DAY TO DAY MAINTENANCE OF PLUMBING SANITARY FITTINGS WELCOME MAINTENANCE OF OFFICERS ACCN AND MISC PETTY BR WORKS AT CHANGSARI MIL STN UNDER GE RANGIA

Amount

M&L for taking down Chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each, complete all as specified and as directed by Engineer-in-charge.

M&L for taking down Shutters of any description not exc 1 sq. m each, complete all as specified and as directed by Engineer-in-charge.

M&L for taking down Shutters of any description exc 1 sq. m and not exc 2 sq. m each, complete all as specified and as directed by Engineer-in-charge.

M&L for Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

M&L for Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as specified and as directed by Engineer-in-charge.

M&L for demolition of reinforced Cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed by Engineer-in-charge.

M&L for demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and as directed by Engineer-in-charge.

M&L for Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed by Engineer-in-charge.

M&L for dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

M&L for demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed by Engineer-in-charge.

M&L for Dismantling timber scantlings 40 sq. cm and over in section, in any position and in unframed work, complete all as specified and as directed by Engineer-in-charge.

M&L for Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section and in unframed work, complete all as specified and as directed by Engineer-in-charge.

M&L for Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed by Engineer-in-charge.

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement; complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match; complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into square with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters and provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b); complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and both faces are covered with decorative face veneer with lipping/frame to match; complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed by Engineer-in-charge.

S&F of 75 mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Double action spring hinges, mild steel with steel wire spring, stove enamelled, black, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, complete all as specified and as directed by Engineer-in-charge.

S&F of 150 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F of 150 mm long Extruded aluminium alloy handles, febricated type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Extruded aluminium alloy handles, cast type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F of Wire netting of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples of mesh size 12mm, complete all as specified and as directed by Engineer-in-charge.

S&F of Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F of 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hard wood in scantling wrought timber unframed and fixed, complete all as specified and as directed by Engineer-in-charge.

M&L for second class hard wood plain fillets in square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc. 6sqcm but not exc.13sqcm, complete all as specified and as directed by Engineer-in-charge.

M&L for second class hard wood plain fillets in square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc. 13sqcm but not exc.25sqcm, complete all as specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius built and set in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering 10mm thick in cement morter 1:6 on the ‘other’ side of lathing, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering (Externally) 15mm thick in Cement Mortar 1:4 in two layers on one side of lathing, 5mm thick top layer mixed with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer-in-charge. NOTE: WPC shall be Measured and Paid as ‘Supply only’ under relevant Item.

M&L for Rendering 15mm thick in cement morter 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering (Externally) 15mm thick in Cement Mortar 1:4 in two layers on fair faces of Brick Walls/Concrete Surfaces, 5mm thick top layer mixed with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer-in-charge. NOTE: WPC shall be Measured and Paid as ‘Supply only’ under relevant Item.

Supply only Integral waterproofing compound, complete all as specified and as directed by Engineer-in-charge.

M&L for precast reinforced cement concrete 1:2:4, type-B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes, etc.) shelves and similar articles with plain faces and set in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge. NOTE : Reinforcement will be measured and paid separately under relevant Item.

S&F of TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

M&L for providing 38mm wide glass dividing strips, 3mm thick, inserted in position, conform to design, complete all as specified and as directed by Engineer-in-charge.

M&L for providing 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Vitrified Ceramic light shade tiles 8 to 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Glazed ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 350x 250x 6-7 mm/ 450x 350x 6-7mm thick, over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of Synthetic enamel paint (1st quality) of any tint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of Creosote oil, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated wooden Surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint and applying two coats of Synthetic enamel paint (1st quality) of any tint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint of any shade over a coat of alkali-resistant priming paint, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper oil emulsion of any shade over a coat of chalk whitening, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly surfaces of ceiling boards and applying two coats of white wash, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly surfaces of walling boards and applying two coats of white wash, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 25mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Refixing including taking down of old steel tubing and connections in new or old position of 15/20/25mm dia; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Rotational Moulded Polyethylene Water Storage Tank 500 Litre capacity (Cylindrical Vertical with Closed Top), 3 layered, hoisted and fixed in position, all as specified in MES Schedule Part-I with and including providing 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 142gm), complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 62 here-in-above, but for 1000 Litre tank, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 142gm), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of exposed powder coated GI snap grid frame work (600x600 mm) for false ceiling comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with suspended hangers of 1 mm dia. G.I. (upto 1200mm length) adjusting level fixed to any type of roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long with and including fixing/ laying/ inserting of pre-painted (white) 4mm thick designer classic E-boards (595x595 mm) to GI frame work, complete all as specified and as directed by Engineer-in-charge.

S&F of 6mm thick asbestos cement, corrugated or semi-corrugated sheets with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc., complete all as specified and as directed by Engineer-in-charge.

Labour only for fixing of 6mm thick asbestos cement, corrugated or semi-corrugated sheets with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc., complete all as specified and as directed by Engineer-in-charge.

S&F of 6mm thick Asbestos cement serrated ridge for corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts in roof, complete all as specified and as directed by Engineer-in-charge.

S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-in-charge.

S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 4mm thick Asbestos cement plain building boards, fixed to timber frame work as in ceiling, flat or sloping with screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 4mm thick Asbestos cement plain building boards, fixed to timber frame work as in walling, flat or sloping with screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China wash basin, white, with brackets, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including 32mm dia CP Waste fittings, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Wash down water closet (Pedestal pattern) pan and S/P trap of 540x375x415mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm dia, with and including making necessary connections, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type Brass CP telephonic wall mixer (3-in-1) for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated shower rose of 125mm dia of rose, fixing to existing pipe or union of 15 mm dia, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type, chromium plated Stop valves/ Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-charge.

S&F of 20 mm bore (dia), gun metal gate valves with iron wheel head, screwed both ends for iron pipe, ISI Marked, as per IS: 778 and including taking out old unserviceable gate valves complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 75mm dia PVC (SWR) bends any radius, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 110mm dia PVC (SWR) bends any radius, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of PVC connection pipe 15mm dia with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.0 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC water tank cover suitable for any capacity PVC water tank 6mm dia MS bar hinging device and S type locking arrangements, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Grating doom of 100 mm dia with waste hole of PTMT (Minimum weight 25gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Grating doom of 125 mm dia with waste hole of PTMT (Minimum weight 40gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 32 mm bore (dia), Waste coupling of PTMT (half or full threaded) (Minimum weight-45gms) complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 40 mm bore (dia), Waste coupling of PTMT (half or full threaded) (Minimum weight-60gms) complete all as specified and as directed by Engineer-in-charge.

S&F of 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

Disconnecting existing tanks exc 500 Ltrs and n.exc 1000 Ltrs, setting aside for repairs, cleaning etc and hoisting if required, reconnecting and refixing in positiion after cleaning and removing all scale and algae formation inside the tank by using TERBAC G5/NB-10/Inchlor-5( lab tested chemical) including fixing sticker mentioning "TANK CLEANED ON' with date, month and year, complete all as specified and as directed by Engineer-in-charge. The cleaning process would follow following stages as under: (a) To drain out the water by using exit valve or high capacity dewatering system (b) Cleaning all the algae formation inside the tank by using TERBAC G5/NB-10/Inchlor-5 chemical. (c) Scrubbing the walls with mechanised scrubber & fresh water cleaning by high speed jet pump. (d) 1st stage of bacteria screening by degermification by using TERBAC G5 halogen compound. (e) Cleaning the floor of the water tank by industrial vacuum cleaner. (f) 2nd stage of bacteria screening & sterilizing method by using UV ray within the tank & killing all suspended bacteria. (g) 3rd stage of bacteria screening by sterilizing the floor of water tank by using strong oxidizing agent TERBAC-G65/NB-60/Inoxi-60. Note: The quoted rate to include for removal of mud, grits and deposits etc properly from site of work and on completion of wk, sterilisation certificate to be submitted to Engineer in Charge. NOTE: (i)Cleaning needs to be done mechanically by authorized dealer/agent as approved by GE. (ii) Chemical shall be approved by GE

M&L for Disconnecting existing PVC tank, setting aside (or lowering if required) and Cleaning of service water tank exc 500 and n.exc 1000 ltrs capacity and connected circulating pipes at any position by removing sludge, mud, moss, moulds, efflorescent salts, oil spots etc or any other foreign material from the bottom, cover and internal surfaces by scraping using wire brush draining out the water in the tank and washing internally by using bleaching powder and again draining out the water in the tank and applying single coat of lime washing on all tanks and marking the date of cleaning with white paint on black back ground including reconnecting and re-fixing in original position complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 100 here-in-above, but for water tank exc 250 and n.exc 500 ltrs capacity, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing old treated/decorated Plastered/Unplastered Surfaces of Walls and eliminating smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying One Coat of white wash, complete all as directed by Engineer-in-charge.

All as per Item No. 102 here-in-above, but on Ceiling, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 102 here-in-above, but applying One Coat of Distemper Oil Emulsion of approved colour, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 102 here-in-above, but applying One Coat of Cement base paint of approved colour, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted steel/ iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for Complete removal of existing Surface Treatment of Walls and preparing the surfaces even and smooth by washing, rubbing down, including removal of nails, etc. and smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and filling cracks/ holes with putty and applying two coats of Distemper Oil Emulsion of approved colour over a coat of internal primer, complete all as specified and as directed by Engineer-in-charge.

BALEN DEWAN

M/S NARAYAN ENTERPRISE

M/S Rajkamal Enterprise

SYED ATAUR RAHMAN