Loading
Loading…
Loading…
Tender Value
₹2.1 Cr
EMD Value
₹4.3 L
Closing Date
31 Aug 2026, 3:00 pm7d left
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
COORD
14 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Note :- (i) For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date). (ii) In case, date of tender inviting is on or after date of statutory deadline for audit of balance sheet of previous Financial Year (i.e. 30th Sept. or as further extended for this FY), audited balance sheet of 4th previous year shall not be considered unless concerned CA certifies that balance sheet is not audited yet as on date of invitation of this tender.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (a) Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or (b) Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or (c) One similar work costing not less than the amount equal to 60% of advertised value of the tender. Note :- For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date).
Defination of Similar Work :- Any Civil Engineering work
7 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
1.The quantities/amount mentioned above are rough and for guidance only and are subject to change according to the needs of the railway & variation there of to any extent will not be the basis of any claim against the Railway.2.The work shall be carried out as per standard specifications (Amended up to date).3.The contract shall be governed by General Condition of Contract and Instructions to the Tenders -2022 (Amended up to date).4.All tools & plants and mechanical equipment as required to execute the work shall be arranged by the contractor.5.Contractor/ suppliers/ service providers/ parties shall register their firms under EPFO & GSTIN (GST Identification Number).
Upgradation of staff infrastructure/refurbishment and Workspace Facilities for 07 no. branches in DRM office, Bikaner under ADEN/HQ/Bikaner
138-26-27~NWR
138-26-27
Open
Works - General
7 Months
Bikaner, Rajasthan
₹0
₹4.3 L
8 Aug 2026
8 Aug 2026
17 Aug 2026
89 items across 2 schedules · ₹21,91,031.25 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Second class teak wood | cum | 1.25 | 1,42,949.7 | 1,78,687.13 |
| 2 | Sal wood | cum | 1.25 | 1,16,520.3 | 1,45,650.38 |
| 3 | 35 mm thick shutters | Sqm | 50 | 4,111.95 | 2,05,597.5 |
| 4 | 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). | Sqm | 212.5 | 2,600.45 | 5,52,595.63 |
| 5 | 125x65x2.12 mm | Each | 375 | 53 | 19,875 |
| 6 | 100x58x1.90 mm | Each | 600 | 45 | 27,000 |
| 7 | 75x47x1.70 mm | Each | 850 | 39.3 | 33,405 |
| 8 | 50x37x1.50 mm | Each | 300 | 18.85 | 5,655 |
| 9 | 150x125x27x2.80 mm | Each | 1200 | 91.7 | 1,10,040 |
| 10 | 125x125x27x2.80 mm | Each | 600 | 86 | 51,600 |
| 11 | 100x125x27x2.80 mm | Each | 600 | 75.35 | 45,210 |
| 12 | 75x100x20x2.24 mm | Each | 375 | 66.65 | 24,993.75 |
| 13 | 150 mm | Each | 600 | 291.35 | 1,74,810 |
| 14 | 125 mm | Each | 600 | 262.9 | 1,57,740 |
| 15 | 100 mm | Each | 600 | 232.7 | 1,39,620 |
| 16 | 150 mm | Each | 600 | 326.9 | 1,96,140 |
| 17 | 125 mm | Each | 600 | 291.35 | 1,74,810 |
| 18 | 100 mm | Each | 600 | 261.15 | 1,56,690 |
| 19 | Overall width 35 mm | Metre | 375 | 336.45 | 1,26,168.75 |
| 20 | Overall width 50 mm | Metre | 375 | 337.9 | 1,26,712.5 |
| 21 | Overall width 65 mm | Metre | 375 | 357.8 | 1,34,175 |
| 22 | 150 mm | Each | 600 | 33.1 | 19,860 |
| 23 | 115 mm | Each | 600 | 29.7 | 17,820 |
| 24 | 90 mm | Each | 600 | 25.3 | 15,180 |
| 25 | 125x64x1.90 mm | Each | 600 | 118.2 | 70,920 |
| 26 | 100X58X1.90 mm | Each | 600 | 107.1 | 64,260 |
| 27 | 75x47x1.80 mm | Each | 600 | 80.05 | 48,030 |
| 28 | 50x37x1.50 mm | Each | 600 | 43.75 | 26,250 |
| 29 | 125x64x2.50 mm | Each | 600 | 129.85 | 77,910 |
| 30 | 100x60x2.50 mm | Each | 600 | 106.35 | 63,810 |
| 31 | 75x50x2.50 mm | Each | 600 | 89.3 | 53,580 |
| 32 | 125x85x5.5 mm (heavy type) | Each | 375 | 268.65 | 1,00,743.75 |
| 33 | 125x70x4 mm (ordinary type) | Each | 300 | 185.15 | 55,545 |
| 34 | 100x85x5.5 mm (heavy type) | Each | 300 | 206.4 | 61,920 |
| 35 | 100x70x4 mm (ordinary type) | Each | 375 | 148.25 | 55,593.75 |
| 36 | 75x65x4 mm (heavy type) | Each | 300 | 173.4 | 52,020 |
| 37 | 75x40x2.5 mm (ordinary type) | Each | 300 | 101.85 | 30,555 |
| 38 | 50x40x2.5 mm (ordinary type) | Each | 300 | 40.9 | 12,270 |
| 39 | 150x125x27x5 mm | Each | 600 | 463.15 | 2,77,890 |
| 40 | 125x125x27x5 mm | Each | 300 | 414.6 | 1,24,380 |
| 41 | 100x125x27x5 mm | Each | 600 | 381.75 | 2,29,050 |
| 42 | 75x100x20x3.2 mm | Each | 300 | 339.2 | 1,01,760 |
| 43 | 250x10 mm | Each | 600 | 441.6 | 2,64,960 |
| 44 | 200x10 mm | Each | 600 | 358.4 | 2,15,040 |
| 45 | 150x10 mm | Each | 600 | 287.25 | 1,72,350 |
| 46 | 100x10 mm | Each | 600 | 197.5 | 1,18,500 |
| 47 | 300x16x5 mm | Each | 300 | 322.2 | 96,660 |
| 48 | 250x16x5 mm | Each | 600 | 308 | 1,84,800 |
| 49 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | Each | 300 | 854.65 | 2,56,395 |
| 50 | Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. | Each | 300 | 726.6 | 2,17,980 |
| 51 | Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. | Each | 300 | 1,183.3 | 3,54,990 |
| 52 | 40 mm | Each | 300 | 311.2 | 93,360 |
| 53 | 50 mm | Each | 300 | 356.75 | 1,07,025 |
| 54 | 65 mm | Each | 300 | 362.4 | 1,08,720 |
| 55 | 75 mm | Each | 300 | 386.6 | 1,15,980 |
| 56 | Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws. | Each | 300 | 74.25 | 22,275 |
| 57 | 125 mm | Each | 300 | 256.65 | 76,995 |
| 58 | 100 mm | Each | 300 | 234.7 | 70,410 |
| 59 | 75 mm | Each | 300 | 184.95 | 55,485 |
| 60 | 125 mm | Each | 300 | 231.05 | 69,315 |
| 61 | 100 mm | Each | 300 | 206.25 | 61,875 |
| 62 | 75 mm | Each | 300 | 176.4 | 52,920 |
| 63 | Providing and fixing aluminium tee channels (heavy duty) with rollers & stop end in pelmets as curtain rod. | Metre | 600 | 160.35 | 96,210 |
| 64 | Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre- laminated particle board as per direction of Engineer-in-charge. | Metre | 600 | 102.15 | 61,290 |
| 65 | Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. | Each | 300 | 850.05 | 2,55,015 |
| 66 | Triple strip vertical type | Each | 300 | 52.5 | 15,750 |
| 67 | Double strip (horizontal type) | Each | 300 | 39.7 | 11,910 |
| 68 | Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer- in-charge. | ONE SET | 300 | 414.2 | 1,24,260 |
| 69 | Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) | Each | 300 | 20.4 | 6,120 |
| 70 | 1.5 mm thick | Sqm | 1800 | 1,045.95 | 18,82,710 |
| 71 | 1.0 mm thick | Sqm | 1800 | 897.3 | 16,15,140 |
| 72 | 12mm thick commercial ply conforming to IS : 1328 BWR type | Sqm | 1500 | 1,224.65 | 18,36,975 |
| 73 | 200 x 19 x 1.9 mm | Each | 1200 | 381.3 | 4,57,560 |
| 74 | 250 x 19 x 1.9 mm | Each | 600 | 422.55 | 2,53,530 |
| 75 | 300 x 19 x 1.9 mm | Each | 600 | 459.55 | 2,75,730 |
| 76 | 350 x 19 x 1.9 mm | Each | 600 | 624.6 | 3,74,760 |
| 77 | 400 x 19 x 1.9 mm | Each | 600 | 610.35 | 3,66,210 |
| 78 | Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS:3818 marked with necessary screw etc all complete. | Sqm | 600 | 2,135.25 | 12,81,150 |
| 79 | Providing and fixing cupboard shutter with 19 mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge. (Payment of providing and fixing auto closing hinges shall be paid separately) | Sqm | 1200 | 2,829.25 | 33,95,100 |
| 80 | 200 mm | Each | 1500 | 186.65 | 2,79,975 |
| 81 | Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. | Each | 600 | 272 | 1,63,200 |
| 82 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. | ONE SET | 600 | 885.1 | 5,31,060 |
| 83 | Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) | Kg | 62.5 | 533.25 | 33,328.13 |
| 84 | Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge. | Metre | 1500 | 43.8 | 65,700 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
General Condition
ATTACHMENT
GCCACS11_compressed.pdf
ATTACHMENT
GCC-2022-uptoACS104.3.25.pdf
ATTACHMENT
Generalcondition01.04.26From01-26-27_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].