GE (AF)/SGR-55/2025-26 ADDITION / ALTERATION TO STATION ARMOURY AT AF STN UNDER GE (AF) SRINAGAR

Amount

Schedule 'A' Part-I (B/R Work)

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in any type of soil, complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

M&L for Hard core of broken stone gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surfaces, complete, all as specified and as directed.

Dismantling of old chain link fencing including flat iron, line wire, complete all as specified and as directed.

M&L for plain cement concrete, 1:4:8, Type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed.

M&L for 40mm thick plain cement concrete, 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) as in damp proof course horizontal or vertical including necessary form work, complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 and finishing even and smooth without using extra cement, complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered wall surfaces by using necessary filling compound of Altek/Birla white 1mm thick wall care putty to obtain smooth / even surface using sand paper and applying two coats of oil bound diameter over a coat of primer, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of anti-fungal exterior emulsion paint over a coat of cement primer including thin layer of wall care putty, complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n exc 25cm, complete all as specified and directed.

Removal of excavated soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point, complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation, complete all as speciified and directed.

M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

M&L for 25mm thick plain cement concrete, 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

M&L for 20-25mm thick machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing / grinding and polishing upto mirror finish complete over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Reinforced cement concrete, M-30 (Design Mix) (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for Reinforced cement concrete, M-30 (Design Mix) (using 20 mm graded crushed stone aggregate) for columns, pillars, piers, posts and struts etc., under-reamed piles and mass concrete, complete all as specified and directed.

M&L for Reinforced cement concrete, M-30 (Design Mix) (using 20 mm graded crushed stone aggregate) for Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

M&L for Reinforced cement concrete, 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Flat rough finished surfaces of concrete complete all as specified and directed

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions Square and rectangle or polygon, complete all as specified and directed.

Formwork for rough finished surfaces of concrete to sides and soffits of floor beams, roof beams, beams, haunchings, girder, lintels, cantilevers, shelves including supports overhangs etc., complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface, not exceeding 200m thick (Horizontal or sloping), complete all as specified and directed.

M&L for MS TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for MS TMT bars 05mm dia and over upto 10mm in in stirrups, spacers and binders, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for plain cement concrete, 1:2:4, Type B-1 (using 20mm graded crushed stone aggregate) as in coping, roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.

M&L for structural steel work as in truss, rafter purling, made out of angle / Hollow pipe / tube section including jointing cleats, plates flat iron, gusset plates, rails, braces etc. conforming to Fe 410-W (gde-E-250) Quality, confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe-290 Gde-E-165, complete all as specified and directed.

M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F in repairs Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F in repairs 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed.

S&F in repairs 0.63mm thick Galvanised, Plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed.

Preparing new zinc (or galvanised) surfaces to receive painting of any description over 10cm width or girth, by coating with mordant solution including washing and cleaning, etc. steel and iron surfaces and applying two coats of synthetic enamel paint over one coat red oxide primer, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed.

S&F anodised Aluminium snap grid frame work of size 605 x 605mm for seamless celling, and hangers 6 mm dia G.I. (Upto 1200 mm length) adjusting level fixed to roof slabs by means of Metre ceiling cleats made out of G.I. Flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes, complete all as specified and directed.

S&F 6mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / GI / aluminium framework with screws including putty to receive finishes, complete all as specified and directed.

Preparation of new or previously untreated plaster/ AC sheet / Gypsum board surfaces of ceiling including cornices and applying two coats of oil bound distemper colour / tint, complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, gates etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings conforming to Fe-290 (Gde?E165) (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, complete all as specified and directed.

M&L for 75mm thick plain cement concrete, 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without extra cement, complete all as specified and directed.

S&F Box type steel window double frame (glazed & gauged) made of ERW tube P- section of size 60mm x 25mm double rebated outer frame comprise glazed Skelton shutter door frame of ERW tube P-section size 50mm x 20mm with two No's openable leaf consisting of two No's of sash bar of T-sec 20mm x 3mm welded to frame with one No vertical mullion of ERW of ERW box type T-section size of 60mm x25mm FI 2mm thick welded / screwed to frame for fixing of wire gauge/glass and 10mm Sqr Bar security grill including fixture and fitting like as handle, tower bolt stopper , cleat, pintail hinges, holdfast primer etc., complete all as specified and directed. (Note- sheet glass, wire mess will be measured and paid separately and window will be measured one side only)

S&F 5.5mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips and rubber neosprine gasket in square or rectangular, complete all as specified and directed by Engineer-in-Charge.

S&F mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 in steel / wooden shutter of door & windows, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M&L for brick work with sub class 'B' bricks (using old size bricks) straight or curved on plan to any radius in half brick thick wall radius, built in CM 1:6, complete all as specified and directed.

M&L for chequered cement concrete tiles size 300 mm x 300 mm x 22-25mm thick with grey cement and pigment , rubber moulded with laquer polish for extra shine, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Complete removal of existing treatment of walls and applying 1mm thick wall care putty and prepare the smooth surface with sand paper and applying two coats of distemper oil emulsion paint, complete all as specified and directed.

Complete removal of existing surface treatment from the old plastered surface of wall and applying two coats of exterior emulsion paint (weather coat) over a coat of exterior primer including scaffolding up to 15m height , complete all as specified and directed.

S&F powder coated aluminium partition n.exc 1.20 Sqm in each panel using 95.6 mm x 44.8mm x 1.6mm frame work with 12 mm thick exterior grade veneered particle boards with decorative veneers on both faces / 5.50 mm thick frosted glass as directed by Engr-in-Charge including aluminium beading for fixing board, complete all as specified and directed.

S&F aluminium powder coated glazed shutter (for doors) with frame of section size 101.60x44.45mm 16 gauge and style and top rail of section 80 x 44mm, 16 Gauge thick and bottom rails of section 112 x 44mm of 16 Gauge thick, middle rail 150 x 44mm of 16 guage thick fixed on floor spring, both side opeining without sash bars but including 5mm thick plain/tinted / heat reflecting glass pan with and necessary jointing cleats, rubber beading, anodized aluminium snap beading, screws, aluminium anodized handle, locking arrangement (mortice lock) and aluminuium anodised tower bolt 200 mm long and hydraulic floor door spring, complete all as specified and directed.

S&F sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm, complete all as specified and directed.

S&F stainless steel plate rack of size 900x650x250mm complete and fixing with rawl plug and steel screws of weight not less than 5 Kg each, complete all as specified and directed.

S&F 15 mm size WHB / sink / wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F 15mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed.

S&F 15mm dia Angle valve, cast copper alloy, chromium plated screwed down, high pressure screwed both ends for iron pipe or for union and fixed, complete all as specified and directed.

S&F 32/40 mm dia bore PVC flexible pipe for wash hand basin / urinal, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed .

S&F 100/75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed.

S&F 110mm size PVC (SWR) bends of any radius fitted with oval access doors, complete all as specified.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Dismantling of RCC posts or struts embedded in concrete, any section, including taking out embedded portion and making good disturbed ground and disposal of old debris to outside the premises ,complete all as specified and as directed.

Dismantling of RCC posts or struts embedded in natural ground, any section, including taking out embedded portion and making good disturbed ground and disposal of old debris to outside the premises ,complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L for plain cement concrete, 1:5:10, Type E-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for plain cement concrete, 1:2:4, Type B-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not etc. 50m and making good surface, work in soft/loose soil, complete all as specified and directed.

S&F MS flat iron clamp, angle posts and struts in fencing cutting tops to shape as directed, drilling holes, notching for wire etc. Flat iron fillets (For securing chain link fencing etc.) and similar work conforming to Fe-410-0, complete all as specified and as directed.

Dismantling of galvanised barbed wire from the existing fencing, complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, as in repair etc. (each line of wire to be measured), complete all as specified and directed.

Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed.

Schedule 'A' Part-II (E/M Work)

M&L for flame proof point wiring for One light / fan point controlled by one way switch 6 amps 240 volts with 2.5 Sqmm copper conductor FRLS (multistrand) PVC insulated ISI marked unsheathed cable in and including surface, stove enamelled steel conduit, medium grade, ISI marked conduit not less than 19mm with all fittings & other accessories and also including PVC insulated ISI marked unsheathed ZHFR cable of size 2.5 Sqmm copper conductor as earth wire to common earth dolly controlled by one flame proof switch (colour code of wiring should be for phase-Red, Neutral-black & earth wire-green), complete all as specified and directed.

S&F flame proof rotary type 16 Amps switch with terminal box in LM 6, single pole, complete all as specified and directed.

S&F flame Proof MCB DB SPN 240 volts 8 way suitable hazardous area laden with gasses/vapours of group II(a) & II (b) as per IS 2148/1994 10 Amp 240 V AC enclosed as per IP 55 protection as per IS 2147/1962 made out of cast aluminium alloy LM 6 having earthing terminal, complete all as specified and directed.

S&F MCB of single poles and current carrying capacity 6 to 32 Amp, 240V, 10 KA 'C' curve, in the MCB DB complete with connection testing and commissioning, complete all as specified and directed.

S&F flame proof LED 60 Watt, CMPRI certified, well glass LED light recommended for Gas/vapour group of II A & II B and Zone 1 & 2 with die cast aluminium housing with heat resistance glass IP 65 protection and all accessories as per manufacture norms & including 3 core flexible cable from ceiling rose to connector of fitting etc., complete as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories 230V, 1200 mm sweep, minimum air delievery 210 CFM with service value 6.00, BEE 5 star rated with brushless direct current motor (BLDC), complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground (earth pit not less than 2.25 metre deep below ground level) vertically, with top edge of the plate not less than 1.25 mtr below normal ground level, connected to galvanized iron wire 4mm dia by means of nuts, bolts, washers of GI steel all as shown on electrical plate No 3 of MES Schedule Part I connected to earthing test point and testing on completion with and including necessary excavation and earth work, earth electrode, earthing lead from electrode to equipment/substation, adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm gradedcrushed stone aggregate) 40mm thick cover, reinforced with 6mm dia bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 15 mm dia with funnel and wire mesh, and 40 mm dia GI light grade earth lead protection pipe, complete all as specified and directed.

Note: (i) The unit rate includes main earthing lead/strip from earth electrode to test point up to 7.5 meter (ii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department.

Supply,installation,commissioning and testing Flameproof inbuilt Heating and Cooling arrangement Ductable air conditioner of capacity 4.0 TR suitable for non CFC refrigirant gas incl material and labour for the following works invalved for smooth functioning & installation of outdoor/indoor for Ductable AC, complete all as directed (a) Fixing the heating & cooling unit with grouting nuts, cutting groove to wall for gas pipe and water drainage pipe complete. (b) S&F cutting, bent to shape copper pipe of appropriate size from outdoor unit to indoor unit by cutting holes to wall incl brazing the copper pipe, fixing union all as required at site. (c) Insulation of both the copper pipe with insulating material and covering the complete pipes with pvc casing & caping of size 75x75mm for mechanical protection of copper pipe complete.

(d) Charging of correct quantity non CFC refrigerant gas after necessary brazing/fixing of both the outdoor/indoor unit and testing complete on load up to saitisfaction of EIC. (e) S&F MS bracket factory made, fixed on wall through fastener of appropriate size and guage for installation of out door unit (condensing unit) complete all as direced. (g) M&L for provision of shed for outdoor unit made of MS sheet 2.0 mm thick and MS angle 30x30x5mm complete. Note - (i) All other connected civil works and other miscellaneous works required for installation of ductable AC & copper functioning as directed.

Supply,installation,commissioning and testing Flameproof inbuilt Heating and Cooling arrangement Ductable air conditioner of capacity 2.0 TR suitable for non CFC refrigirant gas incl material and labour for the following works invalved for smooth functioning & installation of outdoor/indoor for Ductable AC all as directed by Engr-in-charge. (a) Fixing the heating & cooling unit with grouting nuts, cutting groove to wall for gas pipe and water drainage pipe complete. (b) S&F cutting, bent to shape copper pipe of appropriate size from outdoor unit to indoor unit by cutting holes to wall incl brazing the copper pipe, fixing union all as required at site. (c) Insulation of both the copper pipe with insulating material and covering the complete pipes with pvc casing & caping of size 75x75mm for mechanical protection of copper pipe complete.

(d) Charging of correct quantity non CFC refrigerant gas after necessary brazing/fixing of both the outdoor/indoor unit and testing complete on load up to saitisfaction of EIC. (e) S&F MS bracket factory made, fixed on wall through fastener of appropriate size and guage for installation of out door unit (condensing unit) complete all as direced. (g) M&L for provision of shed for outdoor unit made of MS sheet 2.0 mm thick and MS angle 30x30x5mm complete. Note - (i) All other connected civil works and other miscellaneous works required for installation of ductable AC & copper functioning as directed.

S&F UL approved thermal insulation on AC ducts with 13mm thick Class O Nitrile Rubber insulation including providing adhesive, adhesive tapes etc., complete as specified and directed.

Supply, installation, testing and commissioning of 22 gauge site fabricated galvanised steel sheet (GSS) ducting as per the relevant IS of following thickness including necessary supports, adjustable dampers, vanes, etc., complete as specified and directed.

S&F opposed blade aluminum construction volume control dampers in supply air duct collars as per approved drawings and specifications, complete as specified and directed.

Supply, installation, testing and balancing of inlet air louvers with bird screen and volume damper for fresh air in powder coated extruded aluminum construction as per specifications and approved shop drawings, complete as specified and directed.

Supply, installation, testing and balancing of powder coated extruded aluminum square shape ceiling diffusers with removable core and anti smudge ring as per specifications. Quoted price shall be without volume control damper at the location of supply air collar, complete as specified and directed.

Supply, laying, jointing, testing XLPE insulated PVC sheathed with stranded aluminium conductor heavy duty, size of cable 50 Sqmm 3.5 core, conforming to IS 1554 Part I / ISI marked, 1100 Volt grade, including cable glands , cable lugs etc, to suitable the cable size, cables to be laid in trenches, fixed along the poles bare or through GI pipe laid under floors road etc fixed concealed in walls encased in GI pipe etc., complete all as speccified and directed.

Supply, installation and commissioning and testing of LT panel cubical type suitable for 415 volts 3 phase 4 wire, 50Hz AC supply system , floor mounted, out door type factory fabricated duly powder coated inside and outside outer cover made out of 3.15mm thick CRCA sheet , internal cover and partition made out of 2mm thick CRCA sheet with angle iron 50mmx50mmx6mm covered from all side with front and back openable weather proof including suitable size copper cable and embeded in brickwork in CM 1;4 not less than 60cm above ground level with suitable foundation for fixing panel of required size in ground with nuts,bolts, and washers etc complete all as specified and directed.

S&F copper tubing of size 3/8" special annealed pressure copper purity min 99.9% and making flairing at both ends for connection incl brass nut and testing in existing split type air conditioner of any descrtiption/ capacity/make and in any position incl insulating with suitable size insulation, complete as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 m below normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth strip 32 x 6 mm (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 40 mm dia GI pipe medium grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia medium grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit , internal surface of concrete shall be given 10mm thick plaster in CM 1:4 and 40 mm thick precast RCC cover 1 : 2 : 4 ,type B-1( using 20 mm graded crushed stone aggregare ) reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with 12mm dia round bar as in handle including taking down of existing earthing, complete all as specified and directed.

NOTE : (i) The cost of earth lead and its protection pipe upto and including 7.5 m only from the top of earth electrode are deemed to be included under this item and additional earth lead , if any, required at site shall be measured and paid for separately under appropriate item of Schedule `A’/BOQ. (ii) Any joint in earth lead from earth electrode to test point shall not be allowed/permitted.

Deduction to be made from BOQ for Schedule 'A' Part-III (Credit Schedule from dismantling / taking down items) worth Rs 45,635.00 during AOC. (Note :- Tenderers shall not quote for this Schedule)

M/S GHULAM MOHAMMAD AND CO. (BID ID -3488320)

MEGA CONCRETE CONSTRUCTION ENGINEERS AND CONTRACTORS (BID ID -3489305)

M/S maqsood enterprises (BID ID -3489889)

M/S SA INFRATECH (BID ID -3489624)

M/S NAZIR CONSTRUCTION (BID ID -3489701)

M/S Abdul Ahad Rather (BID ID -3487533)

M/S FAROOQ AND SONS (BID ID -3489818)