801673 ADDN ALTN AND IMPROVEMENT TO OMQs and SMQs AT VV CAMP CHALLAGATTA UNDER GE (AF) MARATHAHALLI

Amount

Schedule 'A' Part -I (B/R Works) Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above GL) complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in plinth protection finishing surface even and fair complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description as in sunken slabs, existing roof treatment any type complete all as specified and as directed.

Material and labour for rendering 10mm thick in CM 1:3 finished even and smooth using extra cement with liquid water proofing compound slab treatment as in sunken slab plaster complete all as specified and directed. Note : Water proofing compound measured and paid separately.

Supply only integral liquid water proofing compound .

Supply and fix 40mm bore HDPE pipe as in spout pipes in sunken floors complete all as specified and as directed.

Material and labour for applying Nitoproof 600 PF or equivalent approved product minimum 0.8 mm dft over a priming coat on horizontal and vertical surfaces all as manufactures instruction as in sunken slab surfaces complete all as specified and directed. (NOTE:- After the application of above treatment contractor has to fill the sunken slab surface with water and check for dampness and seepage . In case there as a slightest indication of seepages noticed, the same shall be rectified by injection grouting to seal all cracks or application of polymer modified mortar FOSROC Nitobond SBR of equivalent approved product admixed with the integral WPC or cementitious crystalline waterproofing compound in the affected area to seal all cracks and micro cracks if any and additional coat of Nitoproof 600 PF . This shall be done by contractor at his own cost only and rate is deemed to be included in the rate quoted by the contractor.

Material and labour PCC 1:5:10 lean concrete type C2 using 40mm graded aggregate as in filling of sunken floors complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 using 20mm graded aggregate 40mm thick as in sub base to receive floor finishes complete all as specified and as directed.

Material and labour for providing and applying HS TPO membrane of 1.2mm thick over the layer of 200gsm Geo-Textile with overlap joints of 75 mm in both longitudinal and transverse direction of the TPO and sealed properly with hot air welding and terminate TPO at the top of parapet wall with termination strip and fix it by screw at 300 mm c/c and sealed with HS Joint seal PU on top including surface preparation like remove all loose gravels,dirt,oil,grease,and other foreign particles by jet or dry air and clean the surface mechanically or by grinding to make it smooth before application and PCC / cementitious coving of 75 mm radius shall be provided at all junctions between vertical and horizontal faces before application of TPO completely as per specification and direction. (Note:- work to be carried out by authorised applicator of approved make)

Taking down cement plaster on brick work or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Material and labour for two layer (15 mm thick ) Rendering of top layer 5 mm thick with WPC over a 10 mm thick base layer rendering in CM 1:4 on concrete masonary or surfaces other than fair face of brick work finished fair and even without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid separately.

Material and labour for rendering 10 mm thick in cement mortar 1:6 on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M& L for rendering 10 mm thick cement plaster in CM 1:3 on fair faces of brick work on concrete surfaces on ceiling including finished even and smooth complete all as specified and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) in PCC 1:3:6 type C1 using 20mm garded stone aggregate and setting in mortar 1:4 complete, in walls complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Use and waste of form work to sides and soffits of shelves, cooking platforms etc rough finished surfaces complete all as specified and as directed.

Material and labour for RCC 1:2:4 type B1 using 20mm graded aggregate as in shelves, kitchen platforms etc complete all as specified and as directed.

Material and labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for Mild steel TMT bars 6 to 8mm dia and cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons including granite slab in kitchen platform Laid, bedded and pointed in any mortar etc complete all as specified and as directed.

Material and labour for 18 to 20 mm thick 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado or cooking platform etc laid over cement screed bed 15 mm thick in CM 1 : 4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Dismantling of floor hearth or wall tiling, terrazo tiles of any thickness including cement mortar bedding (but not backing) removing tiles and rubbish off the premises complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles with border tile pattern in vertical surfaces 350 x 250 x 7 mm / 450 x350 x7 mm / 300 x 450 x 7 mm thick , set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and above 10 mm thick cement plaster in 1:3 as backing coat complete all as specified and as directed.

Material and labour for 25mm thick cement concrete type B-0, 1:2:4 (12.50 mm grade aggregate) as in levelling course in flooring finished even and fair under floor finishes complete all as specified and as directed.

Material and labour for Double Charged Vitrified Ceramic Colour tiles 9 to 10 mm thick light shade(Square / Rectangular) polished , area of each tiles not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles over and including cement screed or bedding layer of cement mortar 15mm thick in 1:4 complete all as specified and as directed .

All as per serial item No.28 above but as in skirting over cement mortar backing plaster in CM1:3 10 mm thick complete all as specified and as directed.

Material and labour for non skid joint free coloured ceramic tiles 7 to 8 mm thick (Square/Rectangle) area exceeding 0.11 sqm and but n exceeding 0.18 sqm , in floor etc . set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including cement screed or bedding layer of cement mortar 15 mm thick in 1:4 complete all as specified and as directed.

All as per serial item No.30 above but as in skirting over 10 mm thick cement mortar backing plaster in CM1:3 complete all as specified and as directed.

Material and labour for non skid joint free coloured ceramic tiles 7 to 8 mm thick of size 300mmX300mm in floor set and jointed in cement slurry and pointed with coloured cement to match with coloured tiles over and including cement screed or bedding layer of cement mortar 15 mm thick in 1:4 complete all as specified and as directed.

Taking down steel windows completely of size not exc 1.00 Sqm each complete all as specified and as directed.

Taking down steel windows completely of size exc 1.00 Sqm but nexc 1.5 Sqm each complete all as specified and as directed.

Taking down steel windows completely of size exc 1.50 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame ) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame ) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each as in cupboard shutters/door shutters complete all as specified and as directed.

Supply and fix Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

Supply and fix Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B0 using 12.50 mm graded aggregate as in filling of pressed steel frames for doors, bed blocks complete all as specified and as directed.

Supply and fix 35 mm thick, Factory made Flush shutter, solid core construction, with block board core, with lipping all round complete all as specified and as directed.

Supply and fix 35 mm thick, Factory made second class hard wood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and tread beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); complete all as specified and as directed

Supply and fix Pleated / Collapsible Sliding Mosquito proof Polypropelene Mesh Door with Aluminum frame including locking arrangements with all necessary accessories complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding door (three nos. glazed panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size cording to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) crescent lock (if required). stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fastener 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, including fixing of glass pane complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately in supply only item) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete including fixing of glass pane all as specified and directed by Engineer-in-Charge. (Glass or wire mesh shall be paid separately in supply only items ) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete including fixing of glass pane complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately in supply only item) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Taking down and refixing in same opening of shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

Supply and fix powder coated Aluminium grill for window / ventilators of mesh size 100 x 100 mm and made out of 6 mm thick aluminium powder coated sections including necessary fitting arrangements of approved design/pattern complete all as specified and as directed.

Supply only Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Supply only 4 mm sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq m Each pane complete all as specified and as directed.

Supply only 4 mm sheet glass, ordinary quality and glazing with oil putty in squares exc 0.5 sq m Each pane complete all as specified and as directed.

Supply only 4mm thick figured glass, pin head type as in louvers, fixed glazing not exc 0.5 Sqm in each pane complete all as specified and as directed.

Supply and fix in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples all as specified and as directed

Supply and fix factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing 24 mm thick factory made UPVC door shutters to existing door frames made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter).

Supply and fix 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and directed.

Supply and fix 150 mm long aluminium, anodized barrel tower bolts of extruded section complete all as specified and as directed.

Supply and fix 150 mm long extruded aluminium alloy handle, cast type, anodized complete all as specified and as directed.

Supply and fix 100 mm long butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and as directed.

Supply and fix 200 mm long aluminium, anodized barrel tower bolts of extruded section all as specified

Supply and fix 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fix 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply and fix in repairs of mortise lock vertical type brass 100mm 4 lever complete all as specified and directed.

Supply and fix in repairs 25 mm dia aluminium anodised powder coated type tubular curtains rod including fixing brackets, stops, rollers etc complete all as specified and as directed.

Supply and fix Floor door of stopper aluminium alloy body and tongue, 150 mm overall length, anodised, with hard drawn steel spring, fixed in floor all as specified and as directed

Supply and fix in repairs sinks with draining board made of stainless steel 1 mm thick kitchen with plugs , washers and waste, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm & bowl size 410mmx330mm x 160mm complete all as specified and as directed.

Supply and fix in repairs stainless steel kitchen plate rack of size 760 x 610 x 254mm including fittings complete all as specified and directed.

Supply and fix PVC waste pipe, 32 mm dia, 750mm long, suitable for Kitchen sink, fixed in repairs all as specified and as directed.

Supply and fix in repairs Bib taps, CP brass, fancy type, long body with flange, screwed down, screwed for 15mm bore iron pipes or brass ferrule, fixed in repairs, all as specified and as directed. Make : Jaquar (CAT Part No COP-107PM ) or equivalent in makes specified in PS.

Supply and fix in repairs CP brass, Sink cock with pipe swinging spout ( wall mounted model ) with wall flange , swan neck tap for kitchen sink, all as specified and as directed. Make : Jaquar (CAT Part No COP-347PM) or equivalent in makes specified in PS.

Supply and fix in repairs fancy type CP brass angle cock of brass chromium plated with ling shank screwed for pipe and fixed 15mm bore fixed to iron pipe all as specified Make : Jaquar (CAT Part No COP-057PM) or equivalent in makes specified in PS.

Supply and fix in repairs Health faucet, CP, with 1.5 metre flexible tube with wall hook, (ABS body) 8 mm dia spirochrome flex tube & wall hook, all as specified and as directed. Make : Jaquar (CAT Part No ALD-587) or equivalent in makes specified in PS.

Supply and fix in repairs overhead shower 120 mm round shape single flow (Face plate stainless steel & ABS Body in chrome finish) with rubit cleaning system with brass arm and flange 225mm pipe all as specified and as directed. Make : Jaquar (CAT Part No OHS-1663 ) or equivalent in makes specified in PS.

Supply and fix in repairs CP brass Central hole Basin mixer with out popup waste system with 450 mm long braided hoses 15mm bore all as specified and as directed. Make : Jaquar (CAT Part No COP-167BPM ) or equivalent in makes specified in PS.

Supply and fix in repairs 15 mm bore CP brass wall mixer provision for overhead shower with 115 mm long bend pipe on upper side, connecting legs & wall flanges all as specified and as directed. Make : Jaquar (CAT Part No COP-273PM ) or equivalent in makes specified in PS.

Supply and fix in repairs CP brass Aerator Pillar taps brass chromium plated, fancy type, foam flow, screwed down high pressure screwed for iron pipe 15mm bore, fixed all as specified and as directed. Make : Jaquar (CAT Part No COP-011PM) or equivalent in makes specified in PS.

Supply and fix in repairs S/S Toilet paper holder with flat recessed type complete all as specified and as directed.

Supply and fix in repairs brass chromium plated tubular towel rail 20mm dia D type 60cm ling between flanges complete all as specified and directed.

Supply and fix in repair CP towel Ring Square with Round Flange, Cat Part No-ACN-1121N, complete all as specified and directed . MAKE:- JAQUAR or equivalent in makes specified in PS.

Supply and fix in repair CP Soap Dish Holder, Cat Part No-AKP-35731P, complete all as specified and directed MAKE:- JAQUAR or equivalent in makes specified in PS.

Supply and fix in repairs Mirror cabinet 622x422mm complete all as specified and as directed.

Supply and fix in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fix in repair Corner Glass shelf (with bracket), Cat Part No-ACN-1173, complete all as specified and directed MAKE:- JAQUAR or equivalent in makes specified in PS.

Supply and fix vitreous china wall hung WHB with fixing accessories of size 560x415x200mm Jaquar CAT Part No CNS-WHT-801) with CP brass waste coupling, Jaquar (CAT PART No ALD-705) , waste pipe and full Pedestal (jaquar (CAT Part No -WHT-301 ) all as specified and as directed. Make : Jaquar or equivalent in makes specified in PS.

Supply and fix in repairs Vitreous china wash down water closet pan (pedestal pattern), white, complete with trap, fixed to floor with fixing bolts and seat cover, including connection to drain (or out going pipe) and to flushing pipe, anti - syphonage pipe etc., including making good to floor complete, including fixing of PVC flush tank and seat cover complete all as specified and as directed.

Supply only Plastic water closet seat cover any colour, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device fixed complete all as specified and as directed. (Note: Seat cover make should be same as of WC make)

Supply and fix in repairs vitreous china squatting Orissa pattern pan size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) including trap set in and including concrete complete all as specified and as directed.

Supply only PVC low level flushing cistern, 10 litres capacity, with chromium plated brass inlet and outlet connections including provision of PVC brackets, PVC flush pipe with bend 32 mm dia of suitable length and making necessary connections to water supply pipe line complete all as specified and as directed.

Supply and fix PVC connections 600 mm long between ends with 2 Nos. brass nuts and washers, 15mm size, fixed in repairs, all as specified and as directed.

Supply and fix in repairs CP fancy bib taps 15mm bore complete all as specified and as directed.

Supply and fix in repairs 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs complete all as specified and as directed.

Supply and fix in repairs 32mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs complete all as specified and as directed.

Supply and fix in repairs 40mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs complete all as specified and as directed.

Supply and fix Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted 1000litre capacity and fixed in position all as specified in SSR Part including dismantling old water tank 1000 litre capacity complete all as specified and as directed.

Supply and fix Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted 500litre capacity and fixed in position all as specified in SSR Part including dismantling old water tank 500 litre capacity complete all as specified and as directed.

Supply and fix in repairs 40 mm outer dia ball/gate valve screwed both ends for CPVC pipes and fixed complete all as specified and as directed.

Supply and fix in repairs 32 mm outer dia ball /gate valve for , screewd both ends for CPVC pipes and fixed complete all as specified and as directed.

Supply and fix in repairs Ball valves high 25mm bore pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed. (Minimum weight 15mm-142gms/ 20mm - 210gms / 25mm-455gms/ 40mm - 690 gms)

Supply and fix in repairs 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fix in repairs 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and ceilings complete all as specified and as directed.

Supply and fix in repairs 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fix in repairs 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and ceilings complete all as specified and as directed.

Supply and fix in repairs PVC bends of 110 mm dia complete all as specified and as directed.

Supply and fix in repairs PVC bends of 75 mm dia complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement bends of 75 mm dia complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) junction (Single T) equal or unequal fixed to 75mm bore of pipes with access door complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) junction (Single T) equal or unequal fixed to 110mm bore of pipes with access door complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) vent cowl fixed to 110mm bore of pipes complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) vent cowl fixed to 75mm bore of pipes complete all as specified and as directed.

Supply and fix Stainless steel gratings with frame, 100 mm dia, with/without hole for waste pipe connection complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

Material and labour for 17/18 mm thick Plywood, grade BWP, type BB, fixed with screws to timber frame work as in cupboards , partition, kitchen cabinets, shutters, shelves etc, fixed with screws to timber frame work complete all as specified and as directed.

Material and labour for 0.90 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

Supply and fix 125 mm Brass handles , cast type polished bright complete all as specified and as directed.

Supply and fix nickel plated slip on cupboard/ cabinet hinges suitable for shutters of thickness 15 to 22mm complete all as specified and as directed.

Material and labour second class hardwood Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads not exceeding 3 Sqcm complete all as specified and as directed.

Material and labour for 2 lever brass locks, Cupboards, grade I, size 50mm complete all as specified and as directed.

Supply and fix Semi Modular Kitchen of size Length 3.00 Mtr and width 3.00 mtr comprising of the following :- (i) Storage racks size 0.70mtr high projecting 0.30 mtr from wall above kitchen platform length ( 5.00 Mtr) . (ii) Below kitchen platforms , 10 Nos stainless steel Grade SS-304 basket of size 19/20/21 inch as per site requirement (made out of minimum dia of stainless steel rod 5 mm thick ) with standard telescopic channels including all necessary accessories to be provided and balance portion to be completely covered with door shutter with shelves. (Length below kitchen platform 2 x 3 Mtr) . All cabinets and shelves provided with stainless steel handles zero crank or 90 " hinges, magnetic catches etc as per site requirement. Loft shall be provided with shutters as per site requirements. (iii) Storage racks and kitchen cabins shall be of 18 mm ply wood (BWR) with decorative laminate of approved colour externally and base colour internally . Make : GODREJ, LIVE SPACE, HOME LANE, D LIFE

Material and labour for preparation of old decorated surfaces including brooming down or steel wire brushing, scraping down smokes soot, module, moss and efflorescent salts, oil and greasy spots and applying one coat of white wash on wall surfaces complete all as specified and as directed.

Material and labour for preparation of old decorated surfaces including brooming down or steel wire brushing, scraping down smokes soot, module, moss and efflorescent salts, oil and greasy spots and applying one coat of white wash on ceiling surfaces complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper on wall surfaces over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper on wall surfaces over a coat of alkali resistant primer over 2mm thick wall care putty complete all as specified and as directed.

Material and labour for complete removal of existing treatment of walls and applying two coats of oil bound distemper on wall surfaces over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for complete removal of existing treatment of walls and applying two coats of oil bound distemper on wall surfaces over a coat of alkali resistant primer over 2 mm thick wall care putty complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceilings and applying two coats of oil bound distemper on ceiling surfaces over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of old decorated surfaces including brooming down or steel wire brushing, scraping down smokes soot, module, moss and efflorescent salts, oil and greasy spots and applying one coat of oil bound distemper on ceiling surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment and applying two or more coats of 100% premium acrylic emulsion paint (200 micron) having VOC less than 50 gm / litre and UV resistance as per IS- 15489-2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinned) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over wall surfaces over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for applying two or more coats of 100% premium acrylic emulsion paint ( 200 micron ) having VOC less than 50 gm / litre and UV resistance as per IS- 15489-2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinned) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over newly plastered surfaces of wall surfaces complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

Material and labour for preparation of new wood or wooden based surfaces or previously treated surfaces, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed

Material and labour for preparation of old wood or wooden based surfaces or previously treated surfaces, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed

Removing material or debris retrieved from above demolition or cleaning to a distance exceed 1.5 Km and not exceeding 5.0 Km and depositing where directed complete all as specified and as directed.

Supply and fix pulley operated clothes drying system 7 feet ( 4 pipes of 7' each) consisting of anodised aluminium pipes each of dia 22mm and inner dia 19.80mm, pulleys made up of delrin with rope guide mounted on channel pair of length 24" with locking system , rope will be polyester braided undyed of 4mm dia complete all as specified and as directed.

Supply and fix Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Supply and fix Powder coated Anodised aluminium window and ventilator shutters, fixed type three track windows two glass and one wire mesh shutter without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified Note : Glass pane and SS wire mesh shall be measured and paid separately

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fix mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.complete all as directed and specified.

Supply and fix Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and as directed.

Schedule 'A' Part - II (E/M Works) Taking down carefully copper/aluminium point wiring of any type of batten or conduit (Light, Fan, Socket or power) complete removing material from site and making good the disturbed surfaces of walls, roofs etc including two coats of white/colour washing/distempering etc to match the existing complete all as specified and as directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls complete all as specified and as directed.

Taking down geyser any rating and any size kept in store with out damaging in safe custody complete all as specified and as directed.

Refixing the geyser after repair work complete all as specified and as directed.

Taking down carefully main switches DB's/ MCB DB's/MCB and making good the disturbed surfaces of walls etc complete all as specified and as directed.

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings, capacitors and regulators complete all as specified and as directed.

Material and labour for point wiring with 1.5 sqmm nominal cross sectional area, single core, 1100 Volts FRLS grade, stranded, PVC insulated, unsheathed copper conductor cable drawn through PVC concealed conduit of suitable size, complete with all PVC conduit accessories/ fittings, brass screws, washers etc, including metal flush boxes of suitable size and modular white plate with frame for mounting modular switches, sockets and regulators etc, including all cutting/chases etc in walls and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for the following:-

(a) One light point/fan point controlled by one switch.

(b) One light point controlled by 2 way switch.

(c) One bell point controlled by one bell push

(d) One 3 pin, 05 /06 Amps socket outlet point on same board controlled by one, one way 05/06 Amps switch

(e) One 3 pin, 05 /06 Amps socket outlet point on independent board controlled by one, one way 05/06 Amps switch

All as per Srl Item No. 148 here-in-before, but with 2.5 Sqmm cable and 2.5 Sqmm copper conductor as earth wire for 3 pin, 15 Amps socket outlet

All as per item No.148 above but wiring complete with 4 Sqmm for AC point

Supply and fix modular switch 06 Amps 1 module complete all as specified and as directed.

Supply and fix modular switch 16 Amps 1 module complete all as specified and as directed.

Supply and fix modular socket 06/16 Amps 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fix modular socket 06 Amps 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fix bell push modular type 6 Amps complete all as specified and as directed.

Supply and fix modular switch 2 way , 06 Amps 1 module complete all as specified and as directed.

Supply and draw in conduit sub main wiring with four single core FR PVC insulated stranded copper conductor4 x 6 Sqmm drawn into concealed conduit complete all as specified and FR PVC insulated copper wire 1x6 Sqmm for continuous earth wire complete all as specified and as directed. (Note :- 4 runs of 6 sqmm single cable and one run of 6 sqmm earth wire cable shall be considered as one unit/1RM

All as Srl item No. 157 but two single core 6 Sqmm and 6 Sqmm for earth continuous earth wire.

All as Srl item No. 157 but two single core 4 Sqmm and 4 Sqmm for earth continuous earth wire.

Supplying and fix sheet metal enclosure three phase double door DB flush to wall fitted with bus bar, and neutral link for MCB (without MCB's) 4 ways TPN complete all as specified and as directed.

Supply and fix sheet metal enclosure Single phase double door DB flush to wall fitted with busbar and neutral link for MCB 12 way SPN complete all as specified and as directed.

Supply and fix sheet metal enclosure Single phase double door DB flush to wall fitted with busbar and neutral link for MCB 8 way SPN complete all as specified and as directed.

Supply and fix MCB, single pole 240 volts, capacity 6 Amps to 32 Amp current rating 10KA breaking capacity complete all as specified and as directed.

Supply and fix MCB TPN 63A 415 V B series complete all as specified and as directed.

Supply and fix MCB SPN 40 to 63 A 240 V B series complete all as specified and as directed.

Supply and fix ceiling rose suarface bakelite three terminals 65x50mm complete all as specified and as directed.

Supply and fix electronic fan regulator modular type, 2 module, 120W complete all as specified and as directed.

Supply and fix LED light fittings 1x18 watts,220V ,PC batten type with driver, holder including LED tube light connecting up with three core flexiable copper conductor cable of suitable size from ceiling rose complete with all accessories complete all as specified and as directed.

Supply and fix LED bulb with holder PVC insulated body with back plate for batten fittings 9 watt complete all as specified and directed.

Supply and fix LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V PC batten type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed by Engineer In charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of 250 mm sweep complete all as specified and as directed.

Supply and fix electric water heater, storage type steel body with SS inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Starrated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed.

Supply and fix in replacement Door bell AC, 230 volts, single pole in replacement of old u/s bell/ buzzer complete all as specified and as directed.

Supply and fix 45 W LED Street Light fittingpressure die cast aluminium housing, heat resistance toughened glass, IP-66 protection incl suitable GI bracket in replacement of old UNSV 70W HPSV light fittings complete all as specified and directed.

Material and labour for Telephone wiring complete with 0.40 Sqmm nominal area PVC flexible telephone core solid copper conductor cable unsheated in and incld concealed non metalic rigid PVC conduit 20mm dia ISI marked incld fittings acceories and incld sunken MS terminal box suitable for mounting telephone shocket with 3mm thick Ms plastic sheet cover complete all as specified and as directed.

Supply and fix Telephone socket 2 pin complete all as specified and as directed.

Taking down rusted GI wire and Supply & fixing GI earth wire 4.00 mm dia for interconnecting of earth electrodes complete all as specified and as directed.

Taking down ceiling fan/Exhaust fan, sealing the cable ends dismantling the fan blade kept in safe costody complete all as specified and as directed. Note: (a) Servicing and Spares will be measured and paid seperately.

Supply and fix ceiling fans complete incl anti suicide rods with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fix "S" Hooks for ceiling fans hanging of size 1200 mm sweep making hole on roof for fixing "S" hooks of 10mm dia MS and making good for damaged surfaces complete all as specified and as directed.

Supply only GM bush of ISI marked suitable for ceiling fan of size 1200 sweep complete all as specified and as directed.

Supply only ball bearing suitable for ceiling fan of 1200 sweep complete all as specified and as directed.

Replacement of old unserviceable capacitors 2.5 MFD of the fan in position complete all as specified and as directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan retrieved in item No 178 complete all as specified and as directed.

Material and labour for Painting of ceiling fans/ exhaust fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan retrieved in item No 178 complete all as specified and as directed.

Supply and fix in replacement single pole and neutral enclosure with two pin and earth plug and socket including 1Nos MCB 20Amps capacity complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth lead GI wire 4mm dia (8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts and washers of galvanised iron and thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore light grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:3:6 type C-2 & RCC cover in M-20 (Design mix) and all as shown in Electrical Plate No. 3 of SSR (Part-I) of 2009 complete all as specified and as directed.

Supply and fix concealed rigid non metallic PVC conduit, medium grade with 1.6 mm wall thickness, 20 mm dia (external) for TV including all fittings such as tees, bends, junction and terminal boxes with covers, elbows, reducer etc including RG-II co-axial cable single core copper conductor PVC insulated complete all as specified and directed.

Supply and fix TV Socket 1 module complete all as specified and directed.

S.R.M.K Enterprises (BID ID -3397480)

PRAGATHI BUILDERS (BID ID -3402554)

M/s M Munivenkatappa and Company (BID ID -3396786)

Moulya Builders (BID ID -3397953)

B5BUILDING SOLUTIONS (BID ID -3393663)

K N RAJ CONSTRUCTIONS (BID ID -3405240)