PROVISION OF OPENABLE PULLEY GATE ARRANGEMENT AT BUTCHERY NALLAH AND CERTAIN MINOR WORK AT AFS AMLA

Amount

Demolition of cement concrete reinforced of any description & any position compete all as specified & directed by Engineer-in-Charge

Excavation in post holes (or similar holes) each n exc 0.5 Cum, getting out hard and dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified & directed by Engineer-in-Charge.

M & L Reinforced cement concrete M-25 (Design Mix) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete in post hole complete all as specified & directed by Engineer-in-Charge.

S & F Rolled mild steel Fe 410-W (Gde-E-250) quality-A Rolled section as in main and cross beams, column, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates conforming the relevant IS specification complete all as specified & directed by Engineer-in-Charge. Note: Rolled steel section will include Square Hollow Section Channel, Angle, flat, Round bars etc.

S & F Fe 410-W (Gde-E-250) quality -A mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes complete all as specified & directed.

S & F rolled mild steel Fe 410-W (Gde-E-250) quality-A as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified & directed.

Material and labour for two coats of synthetic enameled paint on new steel and iron surfaces over one coat of red oxide primer on surface over 10 cm width or girth including preparation of new surface complete all as specified & directed by Engineer-in-Charge.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified & directed by Engineer-in-Charge.

S & F premium quality open frame design 3 ton (Max capacity 4.5 ton) chain pulley block with chain and 3 meter lifting capacity and double fall mechanism made of high quality hardened triple spur gears of grade 80 alloy, steel load chain and zinc plated hand chain, reinforced double pawl spring for higher braking efficiency having load chain diameter 8x24 mm, overall dimension 161x199x465x50x40 mm and overall self weight 25.6 kg approx. complete all as specified & directed by Engineer-in-Charge. Make: LIFTIT, SKU: SG-PB-2042

S & F carbon steel, zinc plated wedge type fully threaded design expansion anchor bolt of size 12 mm dia x 150 mm length suitable for concrete, rounded end for easy insertion complete all as specified & directed by Engineer-in-Charge. Make: B.K Jagan and Co. Part No 154FDR2

S & F Mild steel bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

M & L for Excavation over areas by mechanical means (Hydraulic excavator) (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift 1.5m complete all as specified & directed by Engineer-in-Charge.

M & L Plain cement concrete 1:3:6 type C-2 using 40 mm stone aggregate in foundation, filling and mass concrete complete all as specified & directed by Engineer-in-Charge.

M & L formwork (Rough Finish) to sides of concrete foundation footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter complete all as specified & directed by Engineer-in-Charge.

S & F Mild Steel bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

M&L for point wiring using approved colour coding as per IS with 1.5 sq. mm two single core PVC insulated but unsheathed FR cable, 1100 volts grade, ISI-694 marked with multistranded copper conductor and earth continuity wire with similar 1.5 Sqmm cable (including connecting to earth dolly) drawn through ISI Marked heavy-duty rigid PVC concealed conduit with all accessories etc with mild steel sunken box 50mm deep 1.6mm thick with earth dolly duly, concealed in the wall and having modular cover plate with a frame suitable for modular switch/ Sockets/ regulators for the following:-

One light/fan point controlled by one switch one way.

One 3 pin 5 Apms socket outlet point controlled by one way switch on independent board.

All as per item No : 16 point wiring with 2.5 Sqmm two single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 Amp socket outlet point on independent board.

S&F Modular switch 01 way 6 Amp, 01 module comlete all as specified.

S&F Modular switch 01 way 16 Amp, 01 module complete all as specified.

S&F ceiling rose of 3 phase/PVC/polycarbonate, isolated body all as directed.

S&F Modular type fan regulator step type, 120 Watt-02 module complete all as specified.

S&F ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with services value 6.00 BEE. Five star rated including providing flexible copper cable from the ceiling rose to the connector of fan and writing MES number on fan complete all as specified and directed.

S&F Wall mounted fan made of sturdy Engineering plastic complete, AC single Phase, 230A of size 400mm sweep with, blades and protective cage frame, minimum 1400 RPM including necessary installation at site complete all as specified and directed.

S&F Modular socket, 6 Amp – 2/3 Pin combined, 02 module complete all as specified.

S&F module socket, 6 Amp/16 Apm -2/3 pin combined, two in one, 02 module complete all as specified.

S&F double pole plug and socket DBs enclosure with one double pole MCB 16 Apms capacity complete suitable for flush mounting and surface mounting, supplied with natural links for provision for mounting modular devices all as specified and directed by Engineer-in-Charge. Cate Part No. 507860 of Legrand or equivalent in L&T

2 runs of 2.5 Sqmm size main cable and one run of 2.5 sqmm size earth continuity conductor.

Note:- The amount against the Schedule of Credit mentioned in the tender document shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance.

TANUJ CONST. CO.

Captainkomalchaharconstructions