Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹57.2 LAccepted-AOC | ₹57.2 L Quoted ₹57.5 L | L1 | Accepted-AOC ACCEPTED |
| 2 | L2₹59.1 LRejected-Finance AT ROAD NEAR RENUKA CINEMA P O DIST TINSUKIA ASSAM PIN 786125 | TINSUKIA | TINSUKIA | ASSAM | 786125 | ₹59.1 L | L2 | Rejected-Finance NOT THE LOWEST BIDDER |
| 3 | Rejected-Technical COLLEGE ROAD CHABUA PO CHABUA DIST DIBRUGARH ASSAM 786184 | DIBRUGARH | ASSAM | 786184 | - | - | Rejected-Technical REJECT DUE TO ESIC NOT SUBMITTED |
| Sl No | Description | Qty | Unit | STANDARD ELECTRIC WINDERS L2 | FREEZCON L1 |
|---|---|---|---|---|---|
| 1.00 | Comprehensive maintenance and repairs to electrically operated one Make ECE Passanger lift and its controls with safety devices etc with microprocessor variable voltage variable frequency with fault display controller simplex collective selective control to carry 8 patients, of speed 0.7mtrs/sec to serve up to second floor including ground floor with sliding collapsible steel door manually operated thermostat controlled with solenoid valve to prevent accidentally openingo f door during transit with digital car position indicator car operating panel with digital floor position indicator, emergency light, emegency alarm and serial communication system with automatic service device and synchronised leveling including maintenance, repair and replacement of defective parts ( Parts which will be measured and paid separately under relevant items). Inclusive of examination of all safety devices speed governors at fixed periodicity as per requirement, Comducting all laid down safety tests at specified period by qualified and skilled personnel. The lift is required to be serviceable 24 hours round the clock. Any defect noticed during maintenance period shall be attended immediately without any inconvenience to medical authorities, doctor's patients and visitors complete all as specified and directed.[Note :- All the spares/components required for the repair shall be measured and paid separately here-in-after as supply only rates]. | 11 | Per month | 26,200 ₹2.9 L | 25,500 ₹2.8 L |
| 2.00 | Comprehensive maintenance and repairs to electrically operated one Make ECE stretcher lift, microprocessor variable voltage variable frequency with fault display controller simplex collective selective control to carry patient stretcher with attendant and necessary medical equipments, of speed 0.55m/sec to serve up to second floor including ground floor with sliding collapsible steel door manually operated thermostat controlled with solenoid valve to prevent accidentally openingo f door during transit with digital car position indicator car operating panel with digital floor position indicator, emergency light, emegency alarm and serial communication system with automatic service device and synchronised leveling including maintenance, repair and replacement of defective parts ( Parts which will be measured and paid separately under relevant items). Inclusive of examination of all safety devices speed governors at fixed periodicity as per requirement, Comducting all laid down safety tests at specified period by qualified and skilled personnel. The lift is required to be serviceable 24 hours round the clock. Any defect noticed during maintenance period shall be attended immediately without any inconvenience to medical authorities, doctor's patients and visitors complete all as specified and directed.[Note :- All the spares/components required for the repair shall be measured and paid separately here-in-after as supply only rates].For item No 1 & 2: The comprehensive maintenance work of lift shall be carried out by approved equipemnt manufacturer only and item shell be executed after the completion period of comprehensive maintenance under the existing maint contract. | 11 | Per month | 28,350 ₹3.1 L | 27,500 ₹3.0 L |
| 3.00 | M&L in replacement of voice card for stretcher lift & Passanger lift complete all as specified and as directed | 2 | Each | 18,450 ₹36,900 | 17,500 ₹35,000 |
| 4.00 | M&L in replacement of relay card for stretcher lift & Passanger lift complete all as specified and as directed | 2 | Each | 23,000 ₹46,000 | 23,200 ₹46,400 |
| 5.00 | M&L in replacement of fuse card for stretcher lift & Passanger lift complete all as specified and as directed | 20 | Each | 3,400 ₹68,000 | 3,300 ₹66,000 |
| 6.00 | M&L in replacement of SMPS 12 V (switched mode power supply ) for stretcher lift & Passanger lift complete all as specified and as directed | 2 | Each | 8,700 ₹17,400 | 8,500 ₹17,000 |
| 7.00 | S & F Black electrically insulated rubber mat 6 mm thick all as specified and as directed by the Engr-in-Charge | 12 | SqM | 1,685 ₹20,220 | 1,650 ₹19,800 |
| 8.00 | S & F Black autistatic flooring 2 mm thick all as specified and as directed by the Engr-in-Charge | 10 | SqM | 1,180 ₹11,800 | 1,150 ₹11,500 |
| 9.00 | S & F in repairs for ventilation fan to fall ceiling by making a opening/cut to fall ceiling and fix it with necessery control wiring and protection grill all as specified and as directed by the Engr-in-Charge | 2 | Each | 9,260 ₹18,520 | 9,100 ₹18,200 |
| 10.00 | M&L in replacement of travelling cable 24 core 1 sqmm multistranded copper cable (suitable for stretcher and passenger lifts) complete all as specified and as directed. | 80 | RM | 1,200 ₹96,000 | 1,210 ₹96,800 |
Tender Value
₹55 L
EMD Value
₹1.1 L
Closing Date
13 Apr 2026, 6:00 pmClosed
CWE DINJAN
COMMANDER WORKS ENGINEER DINJAN
REPAIR MAINT OF ELECTRICALLY OPERATED LIFTS AT MH AND EOT CRANES AT VARIOUS HANGERS AND MECH LAUNDRY AIR COMPRESSORS UPS AT MH WEIGH BRIDGE AND CONNECTED E/M INFRA UNDER GE DINJAN
2026_MES_756664_1
84546/E8
Open Tender
Electrical and Maintenance Works
330 days
GE DINJAN
AS PER TENDER DETAILS
8 documents required · 8 mandatory
₹1,000
GE DINJAN
₹1.1 L
Yes
16 Jun 2026
17 Mar 2026
20 Apr 2026
17 Mar 2026
13 Apr 2026
7 Apr 2026
M&L in replacement of voice card for stretcher lift & Passanger lift complete all as specified and as directed
M&L in replacement of relay card for stretcher lift & Passanger lift complete all as specified and as directed
M&L in replacement of fuse card for stretcher lift & Passanger lift complete all as specified and as directed
M&L in replacement of SMPS 12 V (switched mode power supply ) for stretcher lift & Passanger lift complete all as specified and as directed
S & F Black electrically insulated rubber mat 6 mm thick all as specified and as directed by the Engr-in-Charge
S & F Black autistatic flooring 2 mm thick all as specified and as directed by the Engr-in-Charge
S & F in repairs for ventilation fan to fall ceiling by making a opening/cut to fall ceiling and fix it with necessery control wiring and protection grill all as specified and as directed by the Engr-in-Charge
M&L in replacement of travelling cable 24 core 1 sqmm multistranded copper cable (suitable for stretcher and passenger lifts) complete all as specified and as directed.
Supply only "Conractor 9 Amps (Siemens make) " complete all as specified and directed.
Supply only "MCB SP 16 Amps to match the exising complete all as specified and directed.
Supply only "Gear oil" complete all as specified and directed.
Supply only " Car main steel wire rope 13 mm dia" complete all as specified and as directed
Supply only " steel wire rope U clip" complete all as specified and as directed
Supply only "O/E/N realy 214 volt DC" complete all as specified and directed.
Supply only "Two phase transformer (415 volts AC)" complete all as specified and directed.
Supply only " controller SSP 440 V " complete all as specified and directed."
Supply only "main controller mother board" complete all as specified and directed."
Supply only "Door bearing for auto door" complete all as specified and directed."
Supply only " Door drive belt V type" complete all as specified and directed.
Supply only "Read switch" complete all as specified and directed.
Supply only " Micro Switch " 15A 250 Volts complete all as specified and directed.
Supply only " Landing Switch" complete all as specified and directed.
Supply only " COP switch" complete all as specified and directed.
Supply only " door drive " complete all as specified and directed.
Supply only " floor sensor " complete all as specified and directed.
Supply only " auto door contact " complete all as specified and directed.
Supply only " auto door motor " complete all as specified and directed.
Supply only " controller fuse card " complete all as specified and directed.
Supply only " controller rectified card " complete all as specified and directed.
Supply only " controller realy 110v to 220v " complete all as specified and directed.
Supply only " main guide shoes 6 mm to 10 mm " complete all as specified and directed.
Supply only " brake coil 100 v to 220 v DC/AC " complete all as specified and directed.
Supply only " automatic door sensor unit" complete all as specified and directed.
Maerial and labour for preparation of old painted mild steel (MS) surfaces of passenger and stretcher lift ( all inside and out side door of the lift) including electric motor, floor of lifts and cabin fan of the lifts, puttying steel surfaces to obtain smooth and even finish and applying two coats of synthetic enemel paints by brush application complete all as specified and directed.
M&L for Servicing of Long Travel 4 Nos Motor alongwith 4 Nos Gear Box complete dismantling, overhauling, gear oil change and fillup complete all as specified and as directed by the Engr-in-charge
M&L for Servicing of Cross Travel motor & gear box assembly by greasing & gear oil change and fillup complete all as specified and as directed by the Engr-in-charge
M&L for Hist motor, gear box grasing & oil change and fillup complete all as specified and as directed by the Engr-in-charge
M&L for Cross travel trolly full checking and greasing complete all as specified and as directed by the Engr-in-charge
M&L for servicing of break assembly and replacement of Leather of LT brake complete including of oil filling all as specified and as directed by the Engr-in-charge
M&L for sevicing, tightness,cleaning of Pannel Board 4 Nos Drive all contractor all relay checking complete all as specified and as directed by the Engr-in-charge
M&L for Guarder repair in, long travel & testing complete all as specified and as directed by the Engr-in-charge
M&L for Long travel all guarder checking and grinding as required complete all as specified and as directed by the Engr-in-charge
M&L for Cross travel guarder checking complete all as specified and as directed by the Engr-in-charge
S/F s*2000VVVF AC drive crank No. 2 change 400 volts complete all as specified and as directed by the Engr-in-charge
M&L for Cross travel motor rewinding 3 phase, 5 HP DC convert 110 V make-bharat bijlee 2 Nos bearing chane complete all as specified and as directed by the Engr-in-charge
M&L for rechecking, callibration and minor repair to pendent push button assembly complete all as specified and as directed by the Engr-in-charge.
M&L for Timer Off relay complete all as specified and as directed by the Engr-in-charge
M&L for Contractor 9 Amps. Cap set of 4 Nos complete all as specified and as directed by the Engr-in-charge.
M&L for MCB Single pole 16 Amps cap complete all as specified and as directed by the Engr-in-charge.
M&L for HRC fuse 32 Amps cap complete all as specified and as directed by the Engr-in-charge
Supply only V belt of Cat No :AX60LP039 B-124 for Industrial washer extrator model AXS 60
Supply only 3way Water Solenoid Valve for Industrial washer extrator model AXS 60 complete all as specified and as directed.
Supply only Door gasket for Industrial washer extrator model AXS 60 complete all as specified and as directed.
Supply only bearing for electric motor for Industrial washer extrator model AXS 60 complete all as specified and as directed.
Supply only Limit Switch for drain-Straight for Industrial washer extrator model AXS 60 complete all as specified and as directed.
S&F in replacement of star delta 3 phase,415 volt starter for pump complete all as specified and as directed. Make L&T/Legrand/Seimens
M& L for servcing of pump Motor sets 5.0 HP capacity the pump sets by repalcing the worn out bushes, gland rope, gland bolts & nuts, etc including testing and commissioning complete all as specified and directed by Engineer-in-Charge.
All as item above capacity of 1.5 HP capaicty complete all as specified and as directed by Engr-in-Charge
M&L in replacement of to indistrial socket multi port as per existing to feed the mechanical laundary electric sypply and dissconect with auto shut option complete all as specified and as directed.
Supply and fixing of driving V belt of size “B-89” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing of driving V belt of size “B-126” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing of driving V belt of size “C-97” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing of driving V belt of size “126” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing of driving V belt of size “B-96” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing of driving V belt of size “B-65” for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply only steam iron heater coil for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply only micro switch for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply only slicon pipe for mechnical loundry including taking out existing unserviceable one complete all as specified and directed.
Supply and fixing in repair 230 Volt, single phase, 3 KW strip heater complete all as specified and directed.
Supply and fixing in repair 230 Volt, single phase, 9 KW round type heater complete all as specified and directed.
Supply and fixing in repair 230 Volt, single phase, 6 KW round type heater complete all as specified and directed.
Supply and fixing in repair 230 Volt, single phase, 3 KW round type heater complete all as specified and directed.
Supply and fixing in repair of industrial grade adjustable timer relay suitable for mechanical laundry operation, 0–15 minutes adjustable timing range, suitable for 230V AC supply, with relay output contacts, complete with mounting accessories, wiring, connections, fixing hardware and all required materials as per site requirement and as directed by Engineer-in-Charge.
Supply and fixing in repair of industrial grade adjustable timer relay suitable for mechanical laundry operation, 60 minutes adjustable timing range, suitable for 230V AC supply, with relay output contacts, complete with mounting accessories, wiring, connections, fixing hardware and all required materials as per site requirement and as directed by Engineer-in-Charge.
Supply and fixing in repair of heavy duty industrial steam press suitable for mechanical laundry, electrically heated type with Heating load 3 kW, operating on 230V/415V AC supply, steam pressure 3–5 bar approx., adjustable temperature up to 200°C; directed by Engineer-in-Charge.
Supply and fixing in repair of 10 mm dia pneumatic pipe suitable for compressed air system, complete with fittings, connectors, clamps, bends, supports and all accessories required for proper installation as per site requirement and as directed by Engineer-in-Charge.
Supply and fix in repair of double function type bearing for washer extractor or drying tumbler of capacity upto 60 KG including all fitting and fixture washer nut, bolts complete all as specified and as directed.
Supply and fix in repair of Vibrator bush as per existing sample complete all as specified and as directed.
M&L for Servicing of Fully electronic lorry weight bridge of capacity 40 MT by providing expert skilled person to check & calibration for lorry bridge using 3 Ton CI test weights incl transportion, repair and test to make the equipment in fully funtional and carry preventive mentance for unintruppted functioning of equipment all as specified and as directed.
Supply only display unit with RS-232 Facility for lorry weight bridge of capacity 40 MT complete all as specified and as directed by Engr-in-charge.
Supply only load cell cup and ball type lorry weight bridge of capacity 40 MT complete all as specified and as directed by Engr-in-charge.
Repair and maintenace of digital microprocesser/ computer system with printing module including refilling/replacing of printer cartridge complete all as specified and as directed by Engr-in-charge.
updating the software(Licence) of computer for lorry weigh bridge complete all as specified and as directed by Engr-in-charge.
Opening the 3 HP induction motor of Air compressor, taking down/out the burnt winding wire and cleaning the slots including rewinding the induction motor with super enamelled copper winding wire of existing gauge ,weight etc. and unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed.
Supply and fixing in repair of Air presure meter in air compresssor complete all as specified and directed
Supply and fixing in repair of V belt in air compresssor complete all as specified and directed
Supply and fixing in repair of Air pessuer switch in air compresssor complete all as specified and directed
Supply and fixing in repair of Comprehesive maint of air compressor complete all as specified and directed
Supply and fixing in repair of Air presure copper line in air compresssor complete all as specified and directed
Supply and fixing in repair of Air filter in air compresssor complete all as specified and directed
Supply and fixing in repair of MN 16 DOL starter type suitable upto 5 HP complete all as specified and directed
M&L for Servicing of 5 KVA ONLINE UPS providing expert skilled person to check, repair and test to make the equipment in fully funtional and carry preventive mentance for unintruppted functioning of equipment all as specified and as directed.
Supply and fixing in repair of 12 V 12 AH battery for UPS complete all as specified and directed
Periodical maintenanc/servicing of 1500 kg capacity bio-degradable waste processing plant including complete inspection, cleaning, lubrication/greasing, replacement of worn-out parts, servicing of shredder, motor, gearbox, heating system, control panel, sensors, bearings and all mechanical/electrical components, complete with consumables, minor spares, tools, labour and all accessories required for proper functioning as per manufacturer recommendations and as directed by Engineer-in-Charge.
Supply and fixing in repair of 230 Volt, single phase, 6 KW heating element complete all as specified and directed.
Supply and fixing in of repair 230 Volt, single phase, 9 KW heating element complete all as specified and directed.
Supply & pouring of Hydraulic Oil ISO VG 68 (N68 grade) suitable for bio-degradable waste processing plant hydraulic systems, compressors and industrial machinery, having anti-wear, anti-oxidation and anti-rust properties, as directed by Engineer-in-Charge.
Sservicing/ maintenace of 100 LPH capacity Reverse Osmosis (RO) water treatment plant including cleaning/replacement of pre-filter cartridges, carbon filter, pump servicing, flushing, chemical cleaning, leak rectification, electrical connections, control panel checking, calibration of TDS controller, replacement of minor spares, consumables, labour, tools and all accessories required for proper functioning as per manufacturer recommendations and as directed by Engineer-in-Charge.
Supply and fixing in repair of RO membrane suitable for 100 LPH Reverse Osmosis plant, thin film composite (TFC) type, compatible with existing membrane housing, complete with replacement, flushing, testing, labour and all accessories required for proper functioning with membrane size 1812/2012 (as per existing system), flow capacity suitable for 100 LPH plant, salt rejection ≥95–98%, operating pressure 60–100 psi approx., pH range 2–11, maximum operating temperature 45°C as directed by Engineer-in-Charge.
Please Enable Macros to View BoQ information
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.24 MB
TenderDocuments.pdf
Tender Documents • 1.03 MB
BOQ_847576.xls
BOQ • 0.33 MB
Download all tender documents and submit your bid