MMPPNA_22_23_207 Construction of road from (i) Arimara to Padigaon from Ch. 0.00 m to 1389.00m, (ii) R.C.C. Box Culvert with Approach on Oiramghat PWD Road to Jumpani 3m x 3m Triple Cell-2 Nos. (Uriamghat Nepali to Kemi), (iii) NH-515 at Adi Leku

Amount

(i) Arimara to Padigaon from Ch. 0.00 m to 1389.00m Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means II) Grading II b) Using Screening Type A (13.2 mm Agg)

Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) With hydrated lime/ cement as filler (refer table 500-9 of MoSRT&H specification) (A) With 60/70 or VG-30 grade bitumen (ii) for Grading II (10 mm nominal size)

Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand ii) 60 cm equilateral triangle.

Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iii) 60 cm circular

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iv) 80cm x 60 cm rectangular.

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Dismantling Dismantling of existing existing structures structures like culverts culverts, bridges bridges, retaining retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202 (I) By Manual Means (c) Reinforced Cement Concrete

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m,dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I).Ordinary soil (i)upto 3 m depth

Filling in Foundation Trenches as per Drawing & Technical Specification Clause 305.3.9 (I) Sand Filling

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 (B) With Natural Gravel (II) P.C.C. Grade M15, Nominal Mix (1:2.5:5)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 A) With crushed stone (IV) RCC Grade M20

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 B) With Natural Gravel (III) PCC Grade M20, Nominal Mix (1:2:4)

Plain/reinforced concrete in sub-structure complete as per drawings and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 (B) With Natural Gravel (II) P.C.C. Grade M20, (I)Nominal Mix (1:2:4)

Plain/reinforced concrete in sub-structure complete as per drawings and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 (A) With Crushed Stone (IV) R.C.C. Grade M25, (I) For Height Upto 5 m

Providing and laying reinforced cement concrete in super-structure as per drawing and Technical Specification' clauses 800, 1205.4 and 1205.5 A) With crushed stone ii) RCC Grade M25 (a)Height upto 5m

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in foundation complete as per drawing and technical specifications clauses 1000 and 1202

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in sub-structure complete as per drawing and technical specifications clauses 1002,1005,1010 and 1202

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in super-structure complete as per drawing and technical specifications clauses 1002,1010 and 1202

Construction of precast RCC railing of M30 Grade, aggregate size not exceeding 12 mm, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications (A) With Crushed Stone

Providing Draiage Spouts complete as per approved drawing and Technical Specification

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification clauses 614,709,1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification clause 1204.3.8

Providing pressure relief pipes 100 mm dia in bottom slab of box cell on a filter media base of 500 mm x 500 mm as per drawing and technical specification Clause 1205.5.7

Providing and Laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications clause 130

Boulder apron laid in wire crates :(Providing & laying boulder apron laid in wire crates made with 4mm dia GI wire conforming to IS:280 & IS:4826 in 100mmX100mm mesh.(weaved diagonally) incldg.10% extra for laps and joints laid with stone boulder wieghting not less than 25 kg each as per drawing and technical specifications clause 1301

Utility Shifting

(ii) R.C.C. Box Culvert with Approach on Oiramghat PWD Road to Jumpani 3m x 3m Triple Cell-2 Nos. (Uriamghat Nepali to Kemi) Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Providing and laying interlocking concrete block pavement with M40 grade grade of concrete blocks having thickness 80mm as per technical specification clause 1504 complete including carriage. a) Including Edge block/ Edge restraints

Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) ii) 60 cm equilateral triangle.

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m,dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I).Ordinary soil (i)upto 3 m depth

Filling in Foundation Trenches as per Drawing & Technical Specification Clause 305.3.9 (I) Sand Filling

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 (B) With Natural Gravel (II) P.C.C. Grade M15, Nominal Mix (1:2.5:5)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 A) With crushed stone (IV) RCC Grade M20

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 B) With Natural Gravel (III) PCC Grade M20, Nominal Mix (1:2:4)

Plain/reinforced concrete in sub-structure complete as per drawings and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 (B) With Natural Gravel (II) P.C.C. Grade M20, (I)Nominal Mix (1:2:4)

Plain/reinforced concrete in sub-structure complete as per drawings and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 (A) With Crushed Stone (IV) R.C.C. Grade M25, (I) For Height Upto 5 m

Providing and laying reinforced cement concrete in super-structure as per drawing and Technical Specification' clauses 800, 1205.4 and 1205.5 A) With crushed stone ii) RCC Grade M25 (a)Height upto 5m

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in foundation complete as per drawing and technical specifications clauses 1000 and 1202

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in sub-structure complete as per drawing and technical specifications clauses 1002,1005,1010 and 1202

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in super-structure complete as per drawing and technical specifications clauses 1002,1010 and 1202

Construction of precast RCC railing of M30 Grade, aggregate size not exceeding 12 mm, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications (A) With Crushed Stone

Providing Draiage Spouts complete as per approved drawing and Technical Specification

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification clauses 614,709,1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification clause 1204.3.8

Providing pressure relief pipes 100 mm dia in bottom slab of box cell on a filter media base of 500 mm x 500 mm as per drawing and technical specification Clause 1205.5.7

Providing and Laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications clause 130

Boulder apron laid in wire crates :(Providing & laying boulder apron laid in wire crates made with 4mm dia GI wire conforming to IS:280 & IS:4826 in 100mmX100mm mesh.(weaved diagonally) incldg.10% extra for laps and joints laid with stone boulder wieghting not less than 25 kg each as per drawing and technical specifications clause 1301

Utility Shifting

(iii) NH-515 at Adi Leku to Torajan Road via Kedi Dolung Tiniali from Ch. 0.00 m to 2280.00 m Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 (including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means II) Grading II b) Using Screening Type A (13.2 mm Agg)

Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) With hydrated lime/ cement as filler (refer table 500-9 of MoSRT&H specification) (A) With 60/70 or VG-30 grade bitumen (ii) for Grading II (10 mm nominal size)

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) ii) 60 cm equilateral triangle.

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iii) 60 cm circular

Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iv) 80cm x 60 cm rectangular.

Providing and Fixing 'Logo' of PMGSY Project: Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Utility Shifting

RCC Box Cell : Excavation for Structures: Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m,dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I).Ordinary soil (i)upto 3 m depth

Filling in Foundation Trenches as per Drawing & Technical Specification Clause 305.3.9 (I) Sand Filling

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 (B) With Natural Gravel (II) P.C.C. Grade M15, Nominal Mix (1:2.5:5)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203 A) With crushed stone (IV) RCC Grade M20

Plain/reinforced concrete in sub-structure complete as per drawings and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 (B) With Natural Gravel (II) P.C.C. Grade M20, (I)Nominal Mix (1:2:4)

Providing and laying reinforced cement concrete in super-structure as per drawing and Technical Specification' clauses 800, 1205.4 and 1205.5 A) With crushed stone ii) RCC Grade M25 (a)Height upto 5m

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL) in super-structure complete as per drawing and technical specifications clauses 1002,1010 and 1202

Construction of precast RCC railing of M30 Grade, aggregate size not exceeding 12 mm, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications (A) With Crushed Stone

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification clauses 614,709,1204.3.7