Addn/ Altn and Repair of lift of Army Hospital RR under GE E/M RR Hospital, Delhi Cantt-10

Amount

Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L for Machine cut kota stone flooring 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 10 mm thick cement screed in cement mortar 1:4 on vertical surfaces complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from frame) area exc. 1.50 Sqm but n .exc 4.00 Sqm each complete all as specified and directed.

S&F MS Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel over a coat red oxide paint.

S & F factory made 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

S&F 100 mm size MS butt hinges medium weight cold rolled complete all as specified and directed.

S&F 150 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised all as directed complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and directed.

S&F 4mm thick aluminium composite panel (ACP Sheet) including necessary clips, rubber packing & aluminium Frame in back pannel of ACP complete all as specified and directed.

S&F in repairs 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including Hacking out old broken glass complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc. complete all as specified and as directed .

M & L for 15 mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement , complete all as specified and as directed .

M&L for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

Cleaning of Rcc surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site condition, grinding any sharp edges, etc

Identify the crack location on parent structure after clean or removal of cover and making 'v' groove of 10 mm wide and 10 mm deep cover crack line by electrically operated angle grinder with diamond concrete saw blade and cleaning it by air pressure all as directed.

M&L for Sealing of exposed 'v' groove of 10 mm deep and 10 mm wide with solvent-free, moisture tolerant, thixotropic, structural adhesive and repair mortar, based on epoxy resins and special fillers, designed for use at temperature between +10°C and +40°C. Product should conforms to ASTM c 881-78, Type I, Grade 3, class B+C: compressive strength > 60N/mm² (14 days) according to ASTM C881 : bond strength <10N/mm² (7 days) according to ASTM C882 all as per manufacturer's instructions & directed .

M&L for drilling holes 10 mm diameter in structural concrete at the interval as per recommendation of engineer-in-charge, clean the holes by air blower prior of fixing nozzles, fixing of packers 9.8 mm diameter, 10 cm long, with high strength steel screw and structure rubber sealing in cleaned holes & Cutting packers by cut of wheel after completion of grouting without damaging structural elements all as per manufacturer's instructions & directed .

M&L for applying one component , polyurethane injection foam based system for wet condition and temporary sealing , which cure to dense flexible foam with a fine cellular structure, Viscosity cps 500-1300 at 23° C all as per manufacturer's instructions & directed .

M&L for applying two component, CE certificate , elastic , low viscous, solvent free, polyurethane injection resin based system for permanent sealing, that does not need the presence of water for hardening reaction , Viscosity of mixture - 250-600 mPaS ( at +30°C) all as per manufacturer's instructions & directed .

M&L for applying epoxy based membrane adhesive @ 3.0 -4.0 kg/m as base coat having mixed density 1.75 kg/ltr; bond strength > 1.5 N/mm2 on junction area upto 200 mm all as per manufacturer's instructions & directed .

M&L for 2 mm thick & 200 mm wide flexible FPO based membrane Combiflex SG system chemical Base Modified flexible Polyolefin (FPO) with advanced adhesion. Fire Rating Euro class E (EN ISO 11925-2, classification to EN 13501-1), Service Temperature -30° C (min) to + 40° C (max) in wet condition & -30° C (min) to +60° C (max) in dry conditions and the product should have tensile strength > 12 N/mm² (EN 12311-2), Tear strength > 40 N/mm (ISO34-B), elongation at Break > 600% (EN 12311-2) and should pass thermal aging : 7500 h passed (SIA V280, 1996) all as per manufacturer's instructions & directed .

M&L for applying epoxy based membrane adhesive @ 3.0 kg/m as base coat having mixed density : 1.75 kg/ltr; bond strength > 1.5 N/mm2 on both sides of joint all as per manufacturer's instructions & directed .

Supply laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volt grade with standard aluminium conductor of size 95 Sqmm 3.5 core complete all as specified & directed.

All as per item No. 29.00 here in before but of size 70 sqmm 3.5 core.

M&L for Earthing complete including taking down of old one with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6.0 mm thick as per IS 3043 of 1987 buried directly in to the ground ( earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to the galvanised earth lead by means of bolts , nuts check nuts and washers of galvanised iron or steel using GI strip 32 x 6 mm as earthing lead as shown in electric plate No -3 of SSR- Part-1 connected to earth test point all as specified or indicated including testing on completion and necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1 :3:6 type C-1 using 20 mm graded stone aggregate, pit, funnel, 15 mm dia medium grade watering pipe, 40 mm dia GI light grade earth lead protection pipe, CI frame and cover , wire copper lugs etc. mesh, charcoal and common salt in alternate layer complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth, for foundations, laying of pipes etc. not exceeding 10 sqm on plan for manholes etc. and not exceeding 1.5 metre in depth and getting out in hard/dense soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified & directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & directed.

M&L for cutting of bituminous road / floor for laying of pipe / cables including , returning filling, spreading, levelling, well ramming in layers, soiling with broken boulders/stones, WBM 7.5 cm thick with coarse aggregate received from dismantling the existing road, premix, carpeting 25 mm thick with ready made mix patch material (emulsified bituminous mix) and compacted for road patch repair work complete all as specified and directed .

M & L for dry sand cushioning to under ground electric cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable all as specified in clause 19.75 of MES schedule part-1 and as directed. Note:-Sand shall be fine sand as specified for plastering.

Supply and laying reinforced precast concert cable cover, class LV, Type-II flat, size 250 mm x 180 mm x 40 mm complete all as specified and directed.

Supply and laying GI pipe medium grade including fitting 40 mm dia complete all as specified and directed.

Supply, installation, testing & commissioning of Car cabin of size WxDxH (2000mmx1100mmx2200mm) and Automatic Centre opening doors (Car) in SS honey comb finish hand rails (OD>40 mm) on 1 sides of car cabin, floor annunciator with music/arrival chime, Car Operating Panel one sides Car Cabin made out of minimum 18 SWG stainless steel (Vandal finish) as well as car cabin roof covered with 18 SWG stainless steel (hair line finish), cabin floor made of Vinyl Tiles, car cabin having powered doors and inspection box at top of the car cabin complete having a minimum fire resistance rating of 01 Hours, LED Light Ultra slim decorative aluminium casted, recess mounted square fixture in white with opal diffuser and separate electronic driver, suitable for low depth ceiling -12 W BLAZE SQUARE with complete accessories including necessary wiring - 02 Nos. Single phase centrifugal type cross flow blower 270 cu meter/hour-02 Nos. complete all as specified and per directed .

Supply, installation, testing & commissioning of Landing Doors in SS honey comb finish with necessary fittings, and complete fixing of Door sensor min 81 beam, 2D infra red full length infra red screen door sensor, over load warning indicator, intercom system with single automatic push button operation with/without attendant ,Do's & Don’ts chart on stainless steel to be installed inside the car cabin complete all as specified and per directed . Note: - Each Job includes nine landing doors.

Supply, installation, testing & commissioning of Micro processor based VVVF Regenerative type main controller with closed loop system. Type of signal system FIGS fixtures with dot matrix display and car position indicator in car all fixture in SS face plate (both inside/out-side),Provn of travelling cable with copper conductor FRLS of suitable size & core or required wiring to intercom speaking, connect to complete cell and provn of through & other accessories, Electric cabling and wiring in FRLS copper cable including all necessary PVC conduits ISI marked of suitable size and anti nuisance car call protection, independent servicing (for duplex only) overload device, Nudging, emergency fireman's service. Emergency car light unit infrared curtain door protection, door time protection, Emergency alarm button, extra door time of lobby & parking door open/close button, emergency battery backup for light, manual rescue operation ,belt inspection drive Auto fan cut off as per IS specifications complete all as specified and per directed .

Supply, installation, testing & commissioning of Inbuilt ARD (Automatic Rescue Device) with maintenance free batteries operated to bring the car cage to the nearest floor level and auto/opening of door for evacuation of passenger in case of power failure & also operate alarm system and emergency light with power backup up to 30 min, Provision of "Press and Speak" system to be connected with lift complaint cell compatible with exchange. Provision of Automatic call registration in case of breakdown complete all as specified and per directed .

Supply, installation, testing & commissioning of Electrically operated Gearless machine(electric motor) AC 415 Volts, 3 Phase 50 HZ of suitable capacity as per IS and operating gearless box with independent main sheave rim, Provision of governor and governor rope of suitable size, buffer springs as per manufacture's design, compact high efficiency drive combined with suspension Traction Media Technology. Provision of safety guarding equipment such as 02 Nos pit switches controller, guarding pit, pulley, guarding pit ladders, facia plate to cover free space between car cabin and hoist way & switches complete all as specified and per directed .

Supply, installation, testing & commissioning of car cabin of size WxDxH (1300mmx1100mmx2200mm) and Automatic Centre opening doors (Car) in SS honey comb finish hand rails (OD>40 mm) on 1 sides of car cabin, floor annunciator with music/arrival chime, Car Operating Panel one sides Car Cabin made out of minimum 18 SWG stainless steel (Vandal finish) as well as car cabin roof covered with 18 SWG stainless steel (hair line finish), cabin floor made of Vinyl Tiles, car cabin having powered doors and inspection box at top of the car cabin complete having a minimum fire resistance rating of 01 Hours, LED Light Ultra slim decorative aluminium casted, recess mounted square fixture in white with opal diffuser and separate electronic driver, suitable for low depth ceiling -12 W BLAZE SQUARE with complete accessories including necessary wiring - 02 Nos. Single phase centrifugal type cross flow blower 270 cu meter/hour-02 Nos. complete all as specified and per directed .

Supply, installation, testing & commissioning of Landing Doors in SS honey comb finish with necessary fittings, and complete fixing of Door sensor min 81 beam, 2D infra red full length infra red screen door sensor, over load warning indicator, intercom system with single automatic push button operation with/without attendant ,Do's & Don’ts chart on stainless steel to be installed inside the car cabin as per directed complete all as specified and per directed . Note: - Each Job includes nine landing doors.

Supply, installation, testing & commissioning of Micro processor based VVVF Regenerative type main controller with closed loop system. Type of signal system FIGS fixtures with dot matrix display and car position indicator in car all fixture in SS face plate (both inside/out-side),Provn of travelling cable with copper conductor FRLS of suitable size & core or required wiring to intercom speaking, connect to complete cell and provn of through & other accessories, Electric cabling and wiring in FRLS copper cable including all necessary PVC conduits ISI marked of suitable size and anti nuisance car call protection, independent servicing (for duplex only) overload device, Nudging, emergency fireman's service. Emergency car light unit infrared curtain door protection, door time protection, Emergency alarm button, extra door time of lobby& parking door open/close button, emergency battery backup for light, manual rescue operation ,belt inspection drive Auto fan cut off as per IS specifications complete all as specified and per directed .

Supply, installation, testing & commissioning of inbuilt ARD (Automatic Rescue Device) with maintenance free batteries operated to bring the car cage to the nearest floor level and auto/opening of door for evacuation of passenger in case of power failure & also operate alarm system and emergency light with power backup up to 30 min, Provision of "Press and Speak" system to be connected with lift complaint cell compatible with exchange. Provision of Automatic call registration in case of breakdown complete all as specified and per directed .

Supply, installation, testing & commissioning of Electrically operated Gearless machine(electric motor) AC 415 Volts, 3 Phase 50 HZ of suitable capacity as per IS and operating gearless box with independent main sheave rim, Provision of governor and governor rope of suitable size, buffer springs as per manufacture's design, compact high efficiency drive combined with suspension Traction Media Technology. Provision of safety guarding equipment such as 02 Nos pit switches controller, guarding pit, pulley, guarding pit ladders, facia plate to cover free space between car cabin and hoist way & switches complete all as specified and per directed .

Supply, installation, testing & commissioning of car cabin size WxDxH (2000mmx1100mmx2200mm) and Automatic Centre opening doors (Car) in SS honey comb finish hand rails (OD>40 mm) on 1 sides of car cabin, floor annunciator with music/arrival chime, Car Operating Panel one sides Car Cabin made out of minimum 18 SWG stainless steel (Vandal finish) as well as car cabin roof covered with 18 SWG stainless steel (hair line finish), cabin floor made of Vinyl Tiles, car cabin having powered doors and inspection box at top of the car cabin complete having a minimum fire resistance rating of 01 Hours, LED Light Ultra slim decorative aluminium casted, recess mounted square fixture in white with opal diffuser and separate electronic driver, suitable for low depth ceiling -12W BLAZE SQUARE with complete accessories including necessary wiring - 02 Nos. Single phase centrifugal type cross flow blower 270 cu meter/hour-02 Nos. complete all as specified and per directed .

Supply, installation, testing & commissioning of Landing Doors in SS honey comb finish with necessary fittings, and complete fixing of Door sensor min 81 beam, 2D infra red full length infra red screen door sensor, over load warning indicator, intercom system with single automatic push button operation with/without attendant ,Do's & Don’ts chart on stainless steel to be installed inside the car cabin as per directed complete all as specified and per directed . note: - Each Job includes six landing doors.

Supply, installation, testing & commissioning of Micro processor based VVVF Regenerative type main controller with closed loop system. Type of signal system FIGS fixtures with dot matrix display and car position indicator in car all fixture in SS face plate (both inside/out-side),Provn of travelling cable with copper conductor FRLS of suitable size & core or required wiring to intercom speaking, connect to complete cell and provn of through & other accessories, Electric cabling and wiring in FRLS copper cable including all necessary PVC conduits ISI marked of suitable size and anti nuisance car call protection, independent servicing (for duplex only) overload device, Nudging, emergency fireman's service. Emergency car light unit infrared curtain door protection, door time protection, Emergency alarm button, extra door time of lobby& parking door open/close button, emergency battery backup for light, manual rescue operation ,belt inspection drive Auto fan cut off as per IS specifications complete all as specified and per directed .

Supply, installation, testing & commissioning of Inbuilt ARD (Automatic Rescue Device) with maintenance free batteries operated to bring the car cage to the nearest floor level and auto/opening of door for evacuation of passenger in case of power failure & also operate alarm system and emergency light with power backup up to 30 min, Provision of "Press and Speak" system to be connected with lift complaint cell compatible with exchange. Provision of Automatic call registration in case of breakdown complete all as specified and per directed .

Supply, installation, testing & commissioning of Electrically operated Gearless machine(electric motor) AC 415 Volts, 3 Phase 50 HZ of suitable capacity as per IS and operating gearless box with independent main sheave rim, Provision of governor and governor rope of suitable size, buffer springs as per manufacture's design, compact high efficiency drive combined with suspension Traction Media Technology. Provision of safety guarding equipment such as 02 Nos pit switches controller, guarding pit, pulley, guarding pit ladders, facia plate to cover free space between car cabin and hoist way & switches complete all as specified and per directed .

Iconic Engineers