Construction of Panchayat Ghar at Platan Block Khour under RGSA for the year 2025-26

Earth work in excavation by mechanical means(hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (notexceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 meters: All kinds of soil

Earthwork in bulk excavation by mech means hydraullic excavator over areas (exceeding 30cm in depth 1.5m in width as well as 10m2 on plan)including disposal of excavated earth lead upto 50mtrs and lift upto 1.5m as directed by Engineer incharge.All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in 1:6 mix

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Providing and laying 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and curing complete(DPC)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood -With ISI Marked MS pressed butt hinges bright finished of required size with necessary screws (35mm thick)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.With ISI Marked MS pressed butt hinges bright finished of required size with necessary screws (30 mm thick)

Providing and fixing 1mm thick MS Sheet door with frame of 40x40x6mm angle iron MS gazat plate at the junctions and corners.All necessary fitting complete incl.applying a priming coat of approved steel primer using Flats 30x6mm for diagonal braces and central cross piece.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : 2nd class kail wood (30mm thick)

Providing and fixing glazed shutters for doors,windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S pressed butt hinges bright finished of required size with necessary screws all complete as per direction of Engineer-in-charge. Second Class Deodar wood (30mm thick)

Providing and Fixing of Hardware Fittings of approved quality T-Bots 250x10mm

T-Bolts 150MM

I-Hook

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm Aldrop

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete in walls any thickness including pilasters butresses,plinth and string coarses,fillets columns,piers etc 1.1:5:3 upto floor level.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth levelMild steel and medium tensile steel bars

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platforms.

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slab

Centering and shuttering including strutting, propping etc. and removal of form for beamsLintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for Foundation

15mmPlaster in 1:6mix

12mm Plaster in 1:6 mix

6mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on new work (two or more coats over and including priming coat with water thinnable cement primer)

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. completeSize of tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all completeFixed to steel windows by welding

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern includingflush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requiedW.C. pan with lSI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT Pillar cock.

P/F of bib cocks 15mm nominal bore of approved quality

Mirror of superior make glass 60x45 cm 4mm thick

Providing and fixing PVC pipes,of approved quality 75mm

F-Trap (110x75mm)

F- Trap (110x110)

Cowl 110mm

Door Bend110mm

Soap Dish

Angle valve

Brass Ball Valve 25mm

Waste Pipes

Cp Grating

Sink Coupling

Connection Pipe

Tank Nipple 25mm

Towel Rod

Providing and fixing G.I /CPVC pipe to IS ( Medium Class) with fitting upto 150mm diad & above shall be MS 7mm thick confirming to IS : 3989 including Synthetic enamel paints of approved quality and shade over a coat of approved priming coat ( Shade as per colour code ) and clamps and flange including cutting & making good walls complete.(internal and Exposed on walls)& includes testing of joints 15mm medium

20mm Medium

25mm Medium

Providing and fixing high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. Thebasesupport i/c fittings & fixtures for tank shall be paid separately

P/f of Water motor of 1HP capacity ( Basic series Crompton ) incl. all necessary fixtures

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, includingpainting of fittings and brackets, cutting and making good the walls wherever required : 610x460mm with Bowel depth 200mm

Providing and fixing glass panes in doors, windows, clerestory windows, all complete with : 5.0mm thick Glass

Making plinth protection 50mm thick of cement concrete 1:3:6.over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated

PVC rain water pipe

Carriage of Sand for an av. Lead 7 km by MT

Carriage of 20mm+40mm agg for an av. Lead 7 km by MT

Carriage of Bricks for an av. Lead 7.0 km

Providing and Making of CIB (Marble Plate) of approved size by way of making another layer of 12mm thick plaster with brick work 1:4 cement mortar on front side outer plaster surface, painting as per the direction of Engineer-in-charge including supply of materials, carriages all complete L.M.R.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 1 x 1.5 sq. mm

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of Recessed conduit as required. 25mm

Supplying and fixing on exisitng GI Box modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 Amp modular socket outlet and 25 Amp modular with MCB, "C" curve including connections, painting etc. as required.

5/6Amp Switch

3 pin 5/6 Amp socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

Bell Push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 6 way Double door

Supplying and fixing 5 amps to 32 amps rating, 240 Volts, 'C" series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Single pole)

Supplying and fixing following Electrical items complete with connections as required. SPN 63 Amp

SPN 40 Amp

Fan Box

M.S Deep Box

Phenolic laminated round sheet 4" dia average

S/F of 16 sq mm twin core almunium cable

S/F of 10 sq mm twin core almunium cable

Angle batten holder

Supplying, installation, testing & commisioning of 20 Watt LED bulb

Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz supply. Exhaust fan 300 mm sweep

Supplying and fixing of ceiling fan 1200 mm sweep

Supplying and fixing of LED street light 70 Watt alongwith wiring with 2 x 1.5 + 1 x 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. and bracket of suitable size as required