Construction of 8 Nos. Type-IV Quarters at Dr. RPGMC and H Tanda in District Kangra, (H.P.). DEPOSIT WORK.(SH-Construction of 8 Nos. Type-IV Quarter including Water Supply and Sanitary Installation.)

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and retuning the soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetra consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings balconies and access platform including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera; with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Lintals beams, plinth beams, cantilevers, girders, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillar, piers, abutments, post and struts including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in stairs cases with slopping or stepped soffits, (excluding landing) except spiral staircase including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying in position cement concrete 1:4:8 (One cement; four sand; eight graded broken/crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and curing complete excluding the cost of centering and shuttering in foundation and plinth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Stone Filling in plinth with approved stone under floors including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five ) design mix to obtain the compressive strength of 25 N/mm square (Twenty five Newton per square millimetre) for reinforced cement concrete work, using cement contents not less than @360 kg/cum (Three hundred sixty kilogram per cubic metre) or as per approved design mix for the work upto plinth level to give a smooth surfaces mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the compressive strength of 25 N/mm square (Twenty five Newton per square millimetre) for reinforced cement concrete work, using cement contents not less than @ 360 kg/cum (Three hundred sixty kilogram per cubic metre) or as per approved design mix for All works above plinth level to all floor level to give a smooth surfaces mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing Tor steel reinforcement of Thermo Mechanically Treated bars of grade Fe-500D of Tata Tiscon/Sail for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Damp Proof Course 100mm (One hundred millimetre) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate) 20mm (Twenty millimetre nominal size) and curing complete, as required at site including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying a coat of residual petroleum bitumen of grade VG-10 (Viscosity grade-Ten) of approved quality using 1.70 Kgs. (one decimal seven zero Kilogram) per square metre on Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil, including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : Six sand : Twelve graded crushed stone aggregate 20mm (Twenty milimetre) nominal size at plinth level in cement mortar 1:6 (One cement: Six sand) complete, including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 (one cement : six coarse sand) including carriage of material with in all leads, lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing angle iron door frames (Double rebate) manufctured from M.S angle section of Tata/Sail/Jindal/Reliance of 40x40x5mm (Forty into forty into five millimetres) and M.S. flat 50x5mm (Fifty into five millimetres) as design and drawing including jamb, lock jamb, beed and if required angle threshold of M.S. angles 50x25mm (Fifty into twenty five millimetres) welded or regidly fixed by mnechanical means lugs with spit ends to each jamb includng steel butt hinges 2.5mm (Two point five millimetres) thick with a provision of locking arrangment and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surfaces complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing angle iron door frames (Single rebate) manufctured from M.S angle section of 40x40x5mm (Forty into forty into five millimetres) and M.S. flat 50x5mm (Fifty into five millimetres) as design and drawing including jamb, lock jamb, beed and if required angle threshold of M.S. angles 50x25mm (Fifty into twenty five millimetres) welded or regidly fixed by mnechanical means lugs with spit ends to each jamb includng steel butt hinges 2.5mm (Two point five millimetres) thick with a provision of locking arrangment and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surfaces complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Brick work using Second class common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) in superstructure above plinth up to all floor level in cement mortar 1:4 (One cement isto four sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing factory made P.V.C. door frame single rebate of any colour of size 50x47 mm (Fifty into forty seven millimetres) with a wall thickness of 5 mm (Five millimetres), made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 (Two) Nos of 150 mm (One hundred fifty millimetres) long brackets of 15x15 mm (Fifteen into fifteen millimetres) M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm (Nineteen into nineteen millimetres) M.S. square tube of 19 (Nineteen) gauge, EPDM rubber gasket weather seal to be provided through out the frame including fixing of door frame to be fixed to wall with M.S. screws of 100 mm (One hundred millimetres) long with wooden or rawl plugs embedded in masonry complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing to existing door frames, 30mm (Thirty millimetres) thick factory made PVC door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19 x 19 mm (Nineteen into nineteen millimetres) for styles and 15x15 mm (Fifteen into fifteen millimetres) for top & bottom rails, (Code no. 9.120 ) of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm (Five millimetres) thick heat moulded PVC 'C' channel of size 30 mm (Thirty millimetres)thickness, 70 mm (Seventy millimetres) width out of which 50 mm (Fifty millimetres) shall be flat and 20 mm (Twenty millimetres) shall be tapered in 45 (Forty five) degree angle on either side forming styles and 5 mm (Five millimetres) thick, 95 mm (Ninety Five millimetres) wide PVC sheet out of which 75mm (Seventy Five millimetres) shall be flat and 20 mm (Twenty millimetres) shall be tapered in 45 (Forty Five) degree on the inner side to form top and bottom rail and 115 mm (One hundred fifteen millimetres) wide PVC sheet out of which 75 mm (Seventy Five millimetres) shall be flat and 20 mm (Twemty millimetres) shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10 mm (Ten millimetres) thick, 20 mm (Twenty millimetres) wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm (Five millimetres) thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails , joints mitres and jointed with solvent cement adhesive including fixing of PVC shutter with existing frame with M.S. nutt hinges 100x50x1.90mm (One hundred into fifty into one point ninety millimetres) size with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 40mm (Forty millimetres) thick 2nd (Second) Class deodar wood fully panelled shutters for doors windows having 12mm (Twelve millimetres) thick both side prelaminated water proof ply board infill panel of Action Tessa/ Century/ Kitlam including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 40mm (Forty millimetres) thick 2nd (Second) Class deodar wood glazed shutters with glass panes of 5mm (Five millimetres) thick plain glass weight not less than 12.50 kg/M2 (Twelve point five zero kilogramme per square metre) of Modiguard/Saint Gobian for shutters with putty and nails complete for doors windows and clerestory windows, including black enamelled iron butt hinges with necessary screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 40mm (Forty millimetres) thick 2nd (Second) Class deodar wood Fly proof stainless steel grade 304 wire guage with 0.5 mm (Zero pont five millimetres) dia wire and 1.4 mm (One point four millimetres) wide aperture with matching wood beading for doors windows and clerestory windows, including bright finished black enamelled iron butt hinges with necessary screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Glazing with glass panes of 5mm (Five millimetres) thick plain glass weight not less than 12.50 kg/M2 (Twelve point five zero kilogramme per square metre) of Modiguard/Saint Gobian for shutters with putty and nails complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 40mm (Forty millimetres) thick 2nd (Second) Class deodar wood glazed shutters with frosted glass panes of 4mm (Four millimetres) thickness (weight not less than 10kg/sqm (Ten kilogramme per square metre) of Modiguard/Saint Gobian for shutters with putty and nails complete for doors windows and clerestory windows, including black enamelled iron butt hinges with necessary screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing the complete box of cup board shall be made of 25mm (Twenty Five millimetre) thick water proof termite resistant commercial board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino ISI marked including shelves. Back side of cup board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply. All the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging. The shutter from all side shall be finished with 1mm ( one millimetre) thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa and 19 mm (Nineteen millimetre) thick water proof comercial board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino including hinges, PTMT handle in wood colour of Prayag Polymers,knob megnatic catcher complete, (outer face of the cupboard shall be measure for payment) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 25 mm (Twenty Five millimetre) thick water proof commercial board of century ply (ISI marked) with 6 mm (Six millimetre) thick hard wood edging all round and PGI sheet linning inside for FF / SDB including fixing with nickel plated piano hinges with screws etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded crushed/broken stone aggregate 40mm nominal size ) and curing complete, excluding cost of form work in foundation and plinth including carriage of material with in all leads, lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing cup-board shutter magnetic catcher with necessary screws etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 65x35mm (Sixty five into thirty five milllimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra (Indian make of approved quality) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of windows etcetra with M.S. flats, square or round bars etcetra including priming coat with approved steel primer all complete.Fixed to steel windows by welding complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Stainlesss steel curtain rail with rollers stop ends and brackets in pelmets with curtain rod of 25mm (Twenty five millimetres) dia and brackets complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into Sixteen millimetres) size aluminium Pilot/sheel sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetera including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred fifty into Ten millimetres) nominal size M.S. Pilot/sheel to required colour and shade with necessary screws etcetra Tower bolts (Barrel type) bright finished or black enameled with nuts and screws etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150x10mm (One hundred fifty into Ten millimetres) nominal size M.S. Pilot/sheel to required colour and shade with necessary screws etcetra Tower bolts (Barrel type) bright finished or black enameled with nuts and screws etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 125mm (One hundred twenty five millimetres) nominal size M.S. Pilot/sheel handles to required colour or shade with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) nominal size M.S. Pilot/sheel handles to required colour or shade with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetres) nominal size M.S. Pilot/sheel handles to required colour or shade with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. PILT/Sheel 250 mm (Two hundred fifty millimetres) size hooks and eyes complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium hanging twin rubber floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etcetra complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS No. 3564, embossed on the body, door weight upto 35 kg ( thirty five kilogram) and door width upto 700 mm ( seven hundred milimetres), with necessary accessories and screws etcetera complete, as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. other taxes imposed by the Government.

Providing and laying 300x450 mm (Three hundred into four hundred fifty millimetres) Ceremic Glazed tiles of Kajaria/ Nitco / Simpolo/Somany / Orient & Bell / AGL/Johnson in skirting risers of steps and dados (in attached toilets) with cement mortar 1:3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete, as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. other taxes imposed by the Government.

Providing and laying cement concrete flooring 40mm (Forty millimetre) thick with 20mm (Twenty millimetre) nominal size stone aggregate 1: 2:4 (One cement : Two coarse sand : Four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 19mm (Nineteen millimetres) thick kota stone in flooring with uniform laid over 20mm (Twenty millimetres ) (average) thickness base of cement mortar 1:3 (one cement : three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 600x600 mm (Six hundred into six hundred millimetres) Double Charged / Ultra charged vitrified floor tiles of Restile Johnson/ Nitco/Kajaria / AGL / Simpolo / Somany /Orient & Bell in flooring, treads of steps and landing as per approved shade and design of the office (thickness to be specified by the manufacturer) with water absorption less than 0.08% (Zero point zero eight percentage) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (Twenty millimetres) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogramme per square metre) including grouting the joints with white cement and matching pigments etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 300x300 mm (Three hundred into three hundred millimetres) antiskid ceremic tiles of Premium Quality of Nitco/AGL/RAK/SIMPOLO/ Kajaria/Somany / Orient Bell /Johnson tiles as per approved shade in flooring in cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 19 mm (Nineteen millimetres) thick Polished Grey Chima Pink Granite Stone having Semi / Round nosing in work top of Kotchen Self laid over 20mm (Twenty millimetres) (average) thickness base of cement mortar 1:3 (one cement : three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 60mm (Sixty millimetres) thick faciory made cement concrete interlocking paver block of NTC / Unistone / Atlantic vibro compacted upto M50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty five millimetres) thick average thickness of cement mortar 1:4 (one cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 150 mm (One hundred fifty millimetres) M.S. single acting spring hinges with necessary screw etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetres) diametre with prepainted limpet and rubber washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing factory made ridges or hips having proper gola shape 60 cm (Sixty centimetres) overall with 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheets of Tata / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty millimetres) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating fixing with prepainted iron J or L hooks, bolts & nuts 6 mm (Six millimetres) dia & prepainted G.I. limpet and bitumen washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 30cm (Thirty Centimetre) wide 25cm (Twenty five centimetre) deep 0.60mm (Zero point six zero millimetres) thick prepainted plain P.G.I. sheet gutter of Tata / Sail / Reliance / Jindals having dome shape grating fixed with bolts, nuts and washers etcetera including making necessary connections with rain water pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 2.0mm (Two point zero milimetres) thick eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-Incharge (Base members of steel work shall be measured and paid separately) including fixing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150 mm (One hundred fifty millimetres) diametre on wall face PVC (D-Plast) rain water pipes of working pressure 4/6 Kg/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Supreme / Prince including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) dia PVC Plain bend on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Supreme / Prince including priming coat, painting and welding etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) dia PVC Shoe on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Supreme / Prince including priming coat, painting and welding etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing (One hundred fifty millimetres) unplasticised -PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm (Fifty into fifty into fifty millimetres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Structural steel work of Tata / Sail / Reliance / Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing angle iron cup-board frames manufactured from M.S. angle iron sections 25x25x5mm (Twenty five into twenty five into five millimetres) thickness including hinges, jambs, lock jambs, beeds if required threshold of M.S. angles 25x25x5mm (Twenty five into twenty five into five millimetres) thickness welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel bolts, nuts 2.50mm (Two point fifty millimetres) thick with shock observes and specified and applying coat of approved steel primer after pre-treatment of surfaces complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x600x6mm (Six hundred into six hundred into six millimetres) Everest fibre cement board ceiling panel with pre-painted GI channel framing @ 600mm (six hundred millimetres) centre to centre complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing water proofing treatment shall be done in two coats apply First coat of Dr. Fixit Torch SHIELD ( P - 3160- 3mm ) to the clean and saturated surface maintaining a coverage 0.60 sqm (Zero point six zero squate meter) per kilogram to achieve 1mm (one millimeter) thickness this coating shall also be executed up to 300mm (Three hundred millimetres) vertically. The 2nd (Second) coat shall be applied in opposite direction after 4 to 6 (Four to six) hours of application of 1st (First) coat then sprinkle sand on top surface of applied Dr. Fixit Fast flex white still tacky and the second coat. Then apply cement mortar 1 : 4 (one cement : four sand) and mixed with Pidiproof LW at the rate 200ml (two hundred millimetre) per 50 (Fifty kilogram) of cement over the floor with suitable gradient towords drain water pipe while the second coat of Dr. Fixit is still tacky complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing staircase railing laying wooden hard rail 75x65mm (Seventy five into Sixty five millimetre) and baluster 85cms (Eighty five centimetre) height for stair case having baluster of 19x19mm (Nineteen into nineteen millimetres) M.S. solid square bars @60Cm (Sixty centimetre) centre to centre embeded in cement concrete steps the vertical balustars to be welded/jointed with each with 2 (two) nos M.S. flat of 40x6mm (Forty into six millimetres) at top and bottam and applying priming coat of red led paint complete in all respect as per specifications approved drawing, design and as directed by the Engineer-in-Chagre. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 50mm (Fifty millimetre) dia M.S. hollow pipe balcony railing upto 90cm (Ninety centimetre) height welded with 25mm (Twenty five millimetre) diametre baluster embedded in cement concrete 30cm (Thirty centimetre) centre to centre and joining with electrical gas welding at top alongwith M.S. hollow pipe with 2 Nos. (Two Number) M.s. flat of 50x5mm (Fifty into five millimetre) including necessary fitting complete as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting Steel work (including priming coat) with enamel paint of Nerolac / Asian to give an even shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10 sqm (Zero point eighty litre per ten square metre) of approved brand and manufacture including cleaning the surfaces of all dirt, dust and other foreign matter complete as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting wood work (including priming coat) with enamel paint of Nerolac/ Asian Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 sqm (Zero point seven five litre per ten square metre) of approved brand and manufacture including cleaning the surfaces of all dirt, dust andother foreign matter complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

6mm (Six millimetres) thick cement plaster to ceiling in cement mortar 1:3 (One cement : Three sand) upto all floor levels complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth witth cement mortar 1:6 (One cement : Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth witth cement mortar 1:4 (One cement : Four sand) complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying white cement based putty of Birla / JK average thickness 1mm (One millimetres) thick, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete upto all floor level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering with oil bound washable distemper with Asian / Dulux / Berger / Nerolac Suraksha paints of approved brand and manufacture to give an even New work (two or more coats) over and including water thinnable priming coat with cement primer after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth upto all floor level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Finishing walls with 100% (One hundred percent) weather proof exterior emulsion of Asian/Dulux/Berger/Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty grams per liter) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point ninety litre per ten square metre) upto all floor level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing plinth protection with 40 mm ( Forty millimetre) thick interlocking paver block of NTC with 23 cm ( twenty three centimetre) dia half round RCC pipe for drainage purpose laid over 10cm (ten centimetre) thick cement concrete 1:4:8 (One cement : four sand : eight graded crushed stone aggregate) in bedding/ haunching complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Excavating trenches of required width for pipes, Cables, etcetra including excavation for sackets, and dressing of sides, ramming of bottoms upto any depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm (Twenty centimetres) in depth, including consolidating each deposited layer by ramming, watering etcetra and disposing of surplus material/ excavated soil as per specifications, approved drawing, design, specification and as per the entire satisfaction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 1620 20mm (Twenty millimetres) O.D. pipe polythene aluminum polythene PE. AL. PE composite pressure pipe confirming to I.S. 15450-2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply , capable to withstand temperature upto 80° degree celcius including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connections etcetra with clamp at 1.00 (One) metre spacing. This includes testing of joints complete for concealed work, including cutting chases and making good the wall etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 2025 25mm (Twenty five millimetres) O.D. pipe polythene aluminum polythene PE. AL. PE composite pressure pipe confirming to I.S. 15450-2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply , capable to withstand temperature upto 80 degree celcius including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connections etcetra with clamp at 1.00 (One) metre spacing. This includes testing of joints complete for concealed work, including cutting chases and making good the wall etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20 to 40mm (Twenty to forty millimetre) nominal bore by providing and fixing tees including cutting and threading the pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal size/diameters in trenches P.V.C. Supreme/ Finolex/ Prince pipe class "A" soil, waste and ventilating pipes 8/4.6mm (Eight/Four point six millimetres) thick fixing with approved adhesive mixure complete including entire carriage of materials complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters in trenches P.V.C. Supreme/ Finolex/ Prince pipe class "A" soil, waste and ventilating pipes 8/4.6mm (Eight/Four point six millimetres) thick fixing with approved adhesive mixure complete including entire carriage of materials complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters P.V.C. clamps ISI marked including finishing with approved design with steel screws and rawl plugs etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters P.V.C. clamps ISI marked including finishing with approved design with steel screws and rawl plugs etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus plain bend of Confirming to IS No. 14735-99 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus plain bend of Confirming to IS No. 14735-99 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus plain tees including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus plain tees including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus Collars including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus Collars including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus Cowl including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex/Relpipe(Reliance)/Vectus Cowl including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110x90mm (One hundred ten into ninety millimeter) Nominal size/diameters PVC floor trap ISI marked of Finolex/Relpipe(Reliance)/Vectus Confirming to BIS-14735-99 self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etcetera complete upto all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash down water closet (European type W.C. pan) of Constellation No. S. No. 20087(S-10) size 57x35x39cm (Fifty seven into thirty five into thirty nine centimetre) with 10 (Ten) litre low level P.V.C. flushing cistern (Sleek plus) having dual flush system of Hindware/Cera/Jaguar of star white/snow white shade with with fitting and brackets, 40mm (Forty millimetres) flush bend, 20mm (Twenty millimetres) over flow pipe, with seat & lid fixed with C.P. brass hinges and rubber buffers, with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and fixed with jet pressure and integral P or S trap including jointing the trap and soil pipe with adhesive of approved brand, (Jet Spray to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash down water closet squatting pan (Indian type W.C. pan) Orissa Pan No 20090 of size 530x410mm (Five hundred thirty into four hundred ten millimetre) of Hindware/Cera/Jagquar of star white shade/snow white with 100mm (One hundred millimetre) P.V.C. P or S trap, 10 (ten) litre low level white PVC flushing cistern having dual flush (Sleek plus) flush pipe with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls (Earth work, bed concrete, foot rest to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 550x400mm (Five hundred fifty into four hundred millimetres) vitreous china wash basin Delta No. 10010 without pedestal of Hindware/Cera/Jagquar with Mirror above of star white shade/snow white with single hole for pillar tap including 15 mm (Fifteen millimetre) nominal bore C.P. brass Pillar tap, 32mm (Thirty two millimetre) nominal bore C.P. brass waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings (Mirror to be measured and paid for seperately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Stainless Steel kitchen sink with drain board of Diamond/Unik/ Preyag big size 610x510x200 mm ( Six hundred ten into five hundred ten into two hundred millimetres) including C.P. waste with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (thirty two millimeter) diametre nominal size C.P. Brass chain and rubber plug of ISI marked for wash basin or sink in all floor level/height complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing (32mm nominal size) diameters M.I. union for wash basin or sink including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diameters flexible P.V.C. waste pipe of Finolex/Relpipe (Reliance) / Vectus for wash basin or sink including brass check nut including PVC waste fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) C.P. iron grating of Superior quality of Jaquar/Hindware/Cera/ESS ESS/Jal for gully trap complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetre) nominal size bevelled edge mirror or superior glass of Modiguard/Saint Gobian mounted on 6mm (Six millimetre) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into twenty millimetres) size CP Brass towel rail of Jaquar/Hindware/Cera/ESS ESS/Jal complete with C.P. Brass brackets fixed to wooden plugs including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x120 mm (Six hundred into One hundred twenty millimetre) nominal size glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P. Brass toilet paper holder (Heavy duty make ISI marked No. 8931 & 8934) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 8mm (Eight millimetre) diametre C.P./S.S. Jet of Jaquar/Hindware/Cera/ESS ESS/Jal with flexible tube upto 1 (one) metre long with S.S. triangular plate to Eureopean type W.C. of approved quality complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) diameters C.P. brass. Bib tap of Opal Prime (Single lever) series of Jaquar/Fiuid (Single lever) series of Hindware/Cera/ESS ESS /Jal ISI marked of approved quality (superior or heavy type) and colour complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diameters C.P. Brass stop cock of Opal Prime (Single lever) series of Jaquar/Fiuid (Single lever) series of Hindware/Cera/ESS ESS /Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Plastic Liquid soap container with C.P. brass lid and brackets fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore P.V.C. connection pipe with brass union 45cm (Forty five Centimeters) length complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) nominal bore/diametre PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm (Three millimetre) thick bolts and nuts complete including finishing with approved adhesive etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetres) nominal bore/diametre PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm (Three millimetre) thick bolts and nuts complete including finishing with approved adhesive etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass angle valve of Jaquar/Hindware/Cera/ESS ESS/Jal without nut and pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass full way valve with wheel of Jaquar/Hindware/Cera/ESS ESS/Jal complete in all respect including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimetres) nominal bore/diametre brass full way valve with wheel of Jaquar/Hindware/Cera/ESS ESS/Jal complete in all respect including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore brass valve (Horizontal plunger) type high pressure with copper plate of Jaquar/Hindware/Cera/ESS ESS/Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and placing water tank make P.V.C. SINTEX/Finolex/Relpipe(Reliance)/Vectus having capacity of 1000 (One thousand) liters each tank necessary fittings including over flow pipe scour pipe etcetra and pads required for inlet and outlet and inside painting ball valve with cover and locking arrangements including painting of good quality complete in all respect including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 150mm (One hundred fifty millimetres) nominal bore/diametres to level or slopes PVC pipe of Finolex/Relpipe(Reliance)/Vectus for sewerage line and jointing with approved adhesive complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 150mm (One hundred fifty millimetres) dia PVC pipe cement concrete 1:4:8 (One cement : four sand; eight graded/crushed stone aggregate 40mm (Forty millimetres) nominal size) all-round PVC pipe including bed concrete/ haunching complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. .

Providing and fixing mixer for kitchen sink with casted swinging spout at top complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded crushed stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (Twenty millimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm (Ninety into eighty centimetres) and 45 cm (Forty five centimetres) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded crushed stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded crushed stone aggregate 20 mm (Twenty millimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm (One hundred twenty into ninety centimetres) and 90 cm (ninety centimetres) deep including C.I. cover with frame (medium duty) 500 mm (Five hundred millimetres) internal diameter, total weight of cover and frame to be not less than 116 kg (One hundred sixteen kilogramme) (weight of cover 58 kg (Fifty eight kilogramme) and weight of frame 58 kg (Fifty eight kilogramme)) : With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (one cement : four coarse sand) C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten millimetres) internal dimensions, total weight of cover with frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)), R.C.C. top slab with 1:1.5:3 mix (one cement : one point five Fine sand : three graded stone aggregate 20 mm (twenty millimetres) nominal size), foundation concrete 1:5:10 (one cement : five fine sand : ten graded stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement : three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 455x610 mm (Four hundred fifty five into six hundred ten millimetres) and 45 cm (Forty five centimetres) deep for single pipe line With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five centimetres) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Ashwani Kumar

Ravi Kumar

Ujjawal Singh