Supply of Spares of coal mills (HP-1103) to RGTPP, Khedar, Hisar on annual rate contract basis.

Supply of Spares of coal mills (HP-1103) to RGTPP Khedar Hisar on annual rate contract basis, For Qty & detail please refer Annexure-1 of NIT in detail

Seal Wear Ring of Coal Mill Journal Assembly Shaft, OD-470 mm, ID-390 mm, Width- 102 mm, MOC-SS304

Journal Assembly Top Cover Plate for Coal Mill HP-1103

Journal Bearing Keeper MOC: En24 Forged, OD-456mm, ID-105mm, PCD-232 mm, 8 nos. of holes of Size M32, thickness-40mm

Journal Housing Seal Cover for Journal Assembly of Coal Mills MOC:IS1020 Cast Steel/EN24

Roller Retainer Ring For coal mills MOC: 16Mn

Journal Housing Guard/Liner Lower, MOC- SS-304

Journal Housing Guard/Liner Upper, MOC: Cast Steel as per IS 1030 Grade-2

Roller Liner Device with Liners For Coal Mill, Base Plate: MS, Liners : Ni Hard

Liner RLD Type-I, MOC: Ni Hard Along With their weld plugs

Liner RLD Type-II, MOC: Ni Hard Along With their weld plugs

Liner RLD Type-III, MOC: Ni Hard Along With their weld plugs

Liner RLD Type-IV, MOC: Ni Hard Along With their weld plugs

Liner RLD Type-V, MOC: Ni Hard Along With their weld plugs

Mill Bowl hub Clamping Ring MOC- 16 Mn (1 Set=4 Nos.)

Shroud Plate1360x120x10 MS (1 Set = 8 Nos.)

Air Restriction Ring Large1800x60x28 MS (1 Set = 8 Nos.)

Air Restriction Ring small 1800x60x28 MS (1 Set = 8 Nos.)

Mill Body Deflector Support Base Plate MS (1 Set = 3 Nos.)

Separator Body Liner-I , MOC: Ni Hard Along With their weld plugs

Separator Body Liner-Il, MOC: Ni Hard Along With their weld plugs

Separator Body Liner-Ill , MOC: Ni Hard Along With their weld plugs

Separator Body Liner-IV, MOC: Ni Hard Along With their weld plugs

Separator Body Liner-V, MOC: Ni Hard Along With their weld plugs

Separator Body Liner-Vl, MOC:Ni Hard Along With their weld plugs

Separator Body Liner-VIl, MOC: Ni Hard Along With their weld plugs

Separator Body Liner-VlIl, MOC: Ni Hard Along With their weld plugs

Separator Body Liner-lX, MOC: Ni Hard Along With their weld plugs

Lower Skirt Carbon Steel, MOC: Carbon Steel ( 1 Set = 4 Nos.)

Bottom Mill Body Side Liners 1mx1mx12mm, MOC: MS (1 set=3 Nos.)

Scrapper With Liner Plate long, MOC:IS 1030, Gr-II, (Cast Steel) MOC of liner ISS 276 ASTM grade-3

Scrapper With Liner Plate, Short, MOC:IS 1030, Gr-II, (Cast Steel)MOC of liner ISS 276 ASTM grade-3

Complete set of Ventury for Coal Mills HP-1103

Set of Classifier Blades OR Vane of Deflector Door High alloying Wear Resistance 55-62 HRC with 4 sets of SS nut & bolts with each plate ( 1 Set = 40 Blades)

MPO base plate Liners Ni Hard Along With their weld plugs

28 " Mill Discharge Valve without pnuematic Cylinder but with Gland sealing Rope, Sliding Plate, Plate Guiding Nuts & Fasteners

Metallic Expansion Bellow/ Antiwear SS 3-D Bellow expansion Joint For PF Piping, Specification: 2 nos. Congulations, (SS 304, Thickness of congulation-2mm, thickness of inner sleeve-5 mm), Medium: Coal+ Hot Air. Maximum Air Flow per Mill:125 Tonne per Hour. Pipe OD-710mm, Thickness of Connection end-16mm (Mild Steel). Position of fitment: Vertical.

Metallic Expansion Bellow/ Antiwear SS 3-D Bellow expansion Joint For PF Piping, Specification: 4 nos. Congulations, (SS 304, Thickness of congulation-2mm, thickness of inner sleeve-5 mm), Medium: Coal+ Hot Air. Maximum Air Flow per Mill:125 Tonne per Hour. Pipe OD-710mm, Thickness of Connection end-16mm (Mild Steel). Position of fitment: Horizontal.

Dresser Coupling with Rubber For center feed pipe of Coal Mill

ERW Straight PC Pipe With ID- 684 mm OD-710 mm Grade - API 5L Low alloy steel Q345

Wearable Adjustable Shrink (adjustable Orifice) for Coal Mill HP-1103, Coal PipeOD-710mm, Model-SMK Type-B (Wearable adjustable shrinks to be supplied with 2 no. extra flange for connection/installation with PC Pipe)

L-150 Coupling with Rubber Spider

Priming Valve for LOP of Coal Mills

Seals of hot shut off gate- L2000 mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Seals of hot shut off gate-L1800mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Link Rod For Hot Regulating Damper

Aluminum Cover for Hot Air Diaphragm, MOC- Al Sheet, 2mm, OD-950mm

Coal Mill Coupling Complete /COUPLING K3741.18.0 HP-1103

Hexagonal Steel SET (mill Coupling) SS-304

Taper bolt with washer & nut MOC: medium carbon steel, EN8

Seal Set Assembly for Gearbox of Coal Mills HP-1103

Feeder Outlet Hopper of RC Feeder

Feeder Outlet gate without actuator

Drive sprocket shaft for feeder outlet gate

Gear for feeder outlet gate

RC feeder gearbox helical gear Small DE, En 24 BORE DIA:25MM,NO. OF TEETH:26,FACE WIDTH:30MM,PITCH CIRCLE DIAMETER:57.182MM, KEYWAY:8X3MM,HELIX ANGLE:20DEG(LH)

RC feeder gear box helical gear NDE, En 24 BORE DIA:43MM,NO. OF TEETH:76,FACE WIDTH:26MM,PITCH CIRCLE DIAMETER:159.68MM, KEYWAY:12X3.5MM,HELIX ANGLE:20DEG(RH)

Gear for COC Gearbox DE, GST1661407, BORE DIA:16MM,NO. OF TEETH:21,FACE WIDTH:15MM,PITCH CIRCLE DIAMETER:34.90MM, KEYWAY:5X2.5MM,HELIX ANGLE:20DEG(LH), MOC: En-24

Gear for COC Gearbox NDE, GST1661407, BORE DIA:25MM,NO. OF TEETH:80,FACE WIDTH:10MM,PITCH CIRCLE DIAMETER:128.6MM, KEYWAY:6X3MM,HELIX ANGLE:20DEG(RH) , MOC: En 24

COC gearbox helical gear both end set

COC chain set (72 chain links & 10 Chain Scrappers), MOC: MS

CLEANOUT CONVEYOR CHAIN REDUCER GEAR BOX SHAFT (COC REDUCER GEAR BOX SHAFT) , MOC: En-27 with Heat Treatment

Coupling for COC of RC Feeder

Idler Roller for RC Feeder Model:CS2036, 1 Set=12 Nos.

Weighing Roller For RC Feeder and Coal MillGT1631107

Tension Roller For RC Feeder and Coal MillGT1653407

Bearing Housing For RC Feeder and Coal Mill GT1651907

Eccentric Bearing Housing For RC Feeder and Coal Mill

Bearing Housing Left For RC Feeder Model: CS2036GT1630407

Bearing Housing Right For RC Feeder Model: CS2036GT1630607

Bearing Housing Assembly & Rode Housing Assembly For RC Feeder and Coal MillGT1632107

Take Up Pulley For RC Feeder Model: CS2024, CS2036GT1650307

Bushing for RC Feeder , PART NUMBER:GT1651807

Take up pulley shaft for RC Feeder

Pyrite Chute/ Tramp Iron Spoute for Coal mill before PV1, MOC: MS, Thickness 16 mm

Collar of Ventury outlet of Coal Mill HP-1103 , MOC: Carbon Steel

Flange for Hot Air Diaphragm

Wear Resistant weld overlay plate with carbide layer of 6mm for Coal Mill, carbide layer on inner side of curved portion Dimensions-height:1500mm, width-1000mm, thickness-10mm (1 Set= 6 Nos.)

Vane Wheel Segment for coal mill ( HP- 1103) ( 1Set = 08 No.)

J and J ENGINEERS (BID ID -1138839)

BMW STEELS LTD. (BID ID -1137447)

MULTIMELT STEELS PVT LIMITED (BID ID -1137508)

UNITECH ENGINEERS (BID ID -1137983)

Shiv Shakti Engineering Works (BID ID -1146809)

SUNAINA ENGINEERING INDUSTRIES (BID ID -1138257)

PVJ MARKETING PVT LTD (BID ID -1137673)

RAJU ENGINEERING WORKS PRIVATE LIMITED (BID ID -1146793)