PROVN OF OPS ROOM AND SERVER ROOM OF E IN C BRANCH AT KASHMIR HOUSE UNDER GE NEW DELHI

Amount

Surface dressing not exceeding 15cm deep as in hard/dense soil complete all as specified and directed.

Excavating in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for foundation etc. and getting out as in Soft/ loose soil complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (Using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Returning filling in, including Spreading, levelling, watering and well ramming in layers n. exc 25cm thick in soils complete all as specified and directed.

M&L for removing excavated material to a distance exc 1.50KM but n exc 5 KM and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for Sand filling under floors tiles including watering and consolidation complete all as specified and directed.

M & L for reinforced cement concrete M-25 (design Mix) using 20mm graded stone aggregate as in foundation, plinth beams, footings and mass concrete etc., complete all as specified and directed.

M & L for reinforced cement concrete M-25 (design Mix) using 20mm graded stone aggregate as in columns etc. complete all as specified and directed.

M & L for reinforced cement concrete M-25 (design Mix) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the lik. complete all as specified and directed.

M&L for use and waste of formwork for sides of columns, rough finished, rectangular, square or polygonal complete all as specified and directed..

M&L for use and waste of formwork for foundation beams etc., for rough finished, flat surfaces complete all as specified and directed.

M & L for TMT bar 6 to 8mm dia cut to length bent to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

M & L for TMT bar 10mm dia and over cut to length bent to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

M&L for 15mm thick Ready mix plaster on brick work or concrete surfaces of wall (External surface) finished even and smooth complete all as specified and as directed.

M&L for preparing surfaces as wall new plastered or unplastered and applying two coats of weather proof exterior 100% acrylic premium emulsion over and including a coat of primer on wall surfaces complete all as specified and directed.

M & L for Polythene film, black, 50 micron laid in floors complete all as specified and directed.

M & L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection etc., finishing cement concrete surface even and smooth without using extra cement complete as specified and directed.

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel , trusses, purlins etc manufactured out of minimum 0. 75 mm thick steel sheet as per design requirements . The Steel sheet shall be galvanized (AZ-150 gms Aluminum Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per 18:875-1987, ISO 800-1984 and 18:801-1975. The wind load shall be as per provisions of IS 875(part-lll). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11 .7/STAAD PROV8i/ArchitekV2 .5.16/Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod , H-Brackets, Boxing Sections, L -Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11 mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings . The slots will be along center line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self-drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM 8633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 and 8 of length 20mm.The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self-expanding carbon steel anchor bolt of dia as per approved drawings and design subject to minimum 12 mm diameter and 121 mm length conforming to AISI 304 and 316 at 500mm c/c with minimumembedment of 1 OOmm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects . The item also includes the submission of stability reports duly examined and issued by any NIT/liT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above. complete all as specified and as directed

M&L for 9 mm thick heavy duty fibre cement planks category IV type A (High pressure steam cured) on external wall and fixing as specified in Ser Item No 26.00 here-in-before complete all as specified and directed.

Providing EIFS (external insulation finishing System) with 1st layer: 25mm thick expanded polystyrene (EPS) fixed on fibre cement board using polymer based adhesive, 2nd layer: 145 GSM fibre glass mesh, 3rd layer: 3 to 4mm thick layer of polymer based render coat

Providing and fixing in all exterior face panels breathable vapour barrier underneath the cement fiber board as per National Building Code 2009 complete as per direction of Engineer-in-charge.

M&L for Rock Wool Insulation 50 mm thick mineral wool (density 48 kg/Cum) insulation to be used as filler between the outer and inner skin of the walls complete all as specified and directed

M&L for 12.5 mm Gypsum Board as on inner face of external wall and both faces of internal walls and fixing as specified in Ser Item No 24.00 here-in-before complete all as specified and directed

M&L for 8 mm thick Fibre Cement Board of category III type B (High pressure steam cured) as on inner face of external wall and both faces of internal walls and fixing as specified in Ser Item No 24.00 here-in-before complete all as specified and directed

Internal Cladding :- Providing & Fixing internal wall panels on light gauge steel frame work with 12.5mmthick gypsum plaster board confirming IS 2095:2011 fixed on 8mm thick fiber cement board confirming to IS 14862:2000 of category III type B (high pressure steam cured) as per standard sizes fixed with self drilling/ tapping screws/ fasterners @60cm c/c of approved make, sscrews shall be sunk rib head of 1.6mm to 4mm thick of 8 to 10 gauge of length varying from 25 to 45mm. Proper taping and jointing to be done using fiber mesh tape and epoxy & acrylic based jointing compound for seamless finish. (cost of frmae work to be paid for separately.)

Providing and fixing precoated galvlume iron profile sheets (PPGL) (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Base Steel from TATA/JINDAL/BHUSHAN Steels Ltd.) (roof sheets+ roof insulation+ roof weld mesh GI)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws complete : (Base Steel from TATA/JINDAL/BHUSHAN Steels Ltd.)

Ridge Plain (500-600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm diameter

Providing and fixing EPDM rubber in between wall frame and foundation

S&F powder coated aluminum door using 96.6mm X 44.8 mm X 1.6 mm aluminium chowkhats 84.0 x44.7mmX1.6mm section vertical styles 101.60X44.88X1.6mm rails including mortice lock vertical type mild steel 100 mm size (Make : Godrej/Harrison) 02 Nos tower bolt 150 mm , door handles, SS butt hinges 125 mm 04 Nos, hydraulic door closer and fittings complete all as specified and directed by Engr-in-Charge bottom panel with 12 mm thick laminated Novapan and top panel with 5.5 mm thick plain glass fixed with snap beading rubber of suitable size Make of glass (MODI/FLOAT/ATUL).

S&F powder coated aluminium sliding window shutters with frames (consisting of 02 Nos grazed shutters and 01 No gauge shutter) series D(25mm), 3 track sliding shutters, duly fitted with neoprene beading glass 5.5mm nominal thickness in gazed shutters, stainless steel wire mess of 0.254 mm nominal dia of wire and 0.95mm average width of aperture in gauzed shutter, 5.0mm thick prelam PVC Sheet fixed with standard aluminium beading in arch portion and powder coated ornamental aluminium grill 8mm dia, 75 x 97 mm aerature fixed with standard aluminium beading fixed in outer portion of the chowkhat etc complete all as specified and as directed.

S&F Glazed Partition with 12 mm thick toughened glass of approved make and manufacture, edges with Crystal/pencil polished all-round with patch fittings of top, bottom, sides and corners patch fixing arrangement and making necessary holes cut out etc. complete all as specified and directed.

M&L for 12.5 mm thick tapered edge gypsum plain board ceiling conforming to IS: 2095- Part I at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4.

M&L for corrugated 0.8 mm thick G S sheet with zinc coating 120 gms/Sqm for decking including vertical/curved surface,fixed with bolts and nuts 8mm diameter with bitumen and GI limpet washers filled with white lead and overlapping of sheet complete (upto any pitch in horizontal/vertical or curved surfaces) excluding cost of purlins,rafters and trusses and including cutting to size and shape wherever required

M&L for Prefabricated structure/PEB: All structural steel shall conform to IS -2062-2011, Built-up members Fy = 345 MPa and Hot rolled sections Fy = 245 MPa & Fy =345 Mpa. The Square Hollow Sections (SHS)/ Rectangular Hollow Sections (RHS) shall be used of grade YST 310 as per IS :4923. Structural steel shall be of 350 MPa conforming to grade E350A/BO/ BR as per IS: 2062. The minimum thickness of plate shall be 6 mm. All anchor bolts shall be of grade 10.9 conforming to IS: 1367 and of minimum size 12 mm. The cover to anchor bolts shall be 40 mm or 1.5 times the diameter of bolt, whichever is more. ASTM F 1554, GRADE 36, Fy=245 Mpa, Suitable provisions shall be made to design and construct special provisions of insert plates, Anchor Fasteners, Cut out etc. High-strength bolts Gr. 8.8/ASTM A325, IS EQUIVALENT IS:4000 Gr.8/IS EQUIVALENT, Washers (flator beveled) Gr. 4 & GR. 8

M&L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and as directed

M&L for plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed

S&F prelaminated PVC rigid foam sheet wall panelling of 5 mm thick stuck on inner frame work of 35 mm wide strips of 5 mm thick rigid foam sheet. The strips should have a groove of 6 mm width and 2 mm depth for sinking the head of screw used to fix the strips to the all and should be placed vertically at equal intervals of 300 mm C/C. The PVC strips to be fixed to the all using 65 mm long MS screws through the groove in the strip by using PVC fasteners including necessary moulding work on doors, windows, pillers and opening etc complete all as directed at site Note:- (a) Work for fixing of wall panelling shall be got executed through manufacturers authorised applicators only under the close supervision of their technical staff. (b) The entire qty of wall panelling and their allied ancillaries shall be procured directly from the manufacturer or their authorised dealer only.

M&L for best quality vinyl wall paper on wall applying with necessary adhesive including matching corners and angles complete all as specified and directed.

M&L for wooden flooring, laminated wooden type made of high density fibre board (HDF), comprising of tongue and groove interlocking type of planks of 1210 x 193 mm size 8mm thick, commercial grade, abrasion resistance of AC-II category, over and including 6 micron polyethylene and foam cushion sheeting over the concrete surface to minimize moisture migration from the concrete including all fixing material i.e. chemical adhesive, base strip/fillets etc. veneered and matching top beading etc. complete all as specified and directed.

M&L for point wiring with PVC insulated sheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for the following :

One light/fan/exhaust point controlled by one no, one way 5 Amp switch.

One light point controlled by two way 5 Amp switches

One bell/buzzer point controlled by one bell push complete all as specified and directed.

One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board

One three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board

All as per item No. 1 here in before but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board.Make:-RR/Polycab/Havells

Note for item No 42 & 43:- (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate.

S&F modular Switch 6 amps, 230 vots, single pole, one way (ISI marked) complete all as specified and directed

S&F modular switch single pole, two way 6 amps complete

S&F modular bell push 6 amps complete

S&F 16 Amp rating modular switch one way one module complete

S&F modular socket out let 230 volts grade (as catered in point wiring above) of following ratings:-

6 Amp - 2/3 pin combined 2 module complete

16 Amp - 2/3 pin combined 2 module complete

S&F electric bell AC 230 Volt complete all as specified and directed .

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified

Supply and fixing modular metal clad single pole & neutral with a 2 pin & earth plug and socket complete with MCB SP 32/20 Amp, 230 volts complete all as specified..

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 4 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 4 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.Make:-RR/Polycab/Havells

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 10 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 10 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.Make:-RR/Polycab/Havells

S&F factory made sheet steel distribution boards, double door, SPN 12 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing all as specified.

Supply and fixing MCB, 240V 10KA, B curve of following poles and current carrying capacity in the MCB DB complete with connection testing. :-

MCB SP 5 to 32 Amps

MCB SP 40 Amps

MCB SPN 32 Amps

Supply and lay cable XLPE Insulated screened PVC bedded,galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified

M&L for chemical earthing complete with earth electrode made of high tensile low steel circular rods, molecularly bonded with copper on outer surface to meet the relavent indian standards and shall be of the approved make & design. the earth electrode shall confirm IS and of minimum 17 mm dia and minimum 2 mtr long & thickness of copper bonding minimum 250 microns. hole of 100 mm to 120 mm dia shall be augured to a depth of about 2.5 mtr. earth electrode shall be placed into the hole. by penetrating it into the soil gently diving on the top of the rod, so that min. 150 mm of the electrode shall be ibserted in the natural soil/ present soil. earth enchancement material (minimum approx. 20 Kg) shall be filled in to the augured hole in slurry from and allowed to set. after the material get set, the diameter of composite structure (earth electrode + earth enchancement material) shall be of minimum 100 mm dia covering entirelength of the hole. remaining portion of the hole shall be covered by backfill soil/ material. A copper strip of 150mmx25mmx6mm shall be exothermically welded to main earth electrode for taking the connection to the main equi-potential earth bus bar /ICT centre. multi strand single core PVC insulated 10 Sqmm copper cable connecting to main earth electrode. earth enhancement material consist of Graphite and portland cement. Bentonite content shall be negligible. high conductivity & humidity retention capability, non corrosive in nature having low water soiubility but highly hygroscopic. Inspection chamber size of 300x300x300 mm (inside dimension) box (concret / Iron) with smooth finish shall be provided on the top of the pit. A concrete /Iron lid painted black with pulling hooks, shall be povided to cover the earth pit. copper lugs with stainless steel nut and bolts complete all as directed.

Supply and fixing aesthetically designed Wall/Ceiling mounted decorative downlighter LED light of 15 W fixture with opal diffuser to give glare free light including suitable LED lamp of 12 W complete all as specified

Supply and fixing in replacment BLDC ceiling fan 1200 mm sweep,300 RPM, 230 volts having full copper motor & ribbed alluminium blades for higher air delivery,powder coating provides longer life complete with accessories including making arragement to hanging of fan to ceiling with proper hook nut bolts complete all as specified & directed.

Supply and fixing in replacement of wall fan 400mm (16 inch) 60 watt Oscilating wall fan (KD white) wall mounted speed 1350 RPm completet allas specified and directed by Engineer in Charge Make :bajaj,crompton,havellsand including cutting bricks/stone boulders wall for fixing of fan and finished the cutting surface even and smooth by using cement morter complete all as specified and directed by Engineer in charge

Supply and fix industrial plug and socket 32 rating 3P+N+E suitable for IP-76 degree of protection complete all as specified

Supply, installation, testing and commissioning of Split Air-conditioner Hi wall Model of cooling capacity 1.5 TR consisting air cooled copper condenser coil, 3D Airflow, PM 2.5 filter, Anti-corrosion treatment for better air quality, Display on Indoor unit, cordless LED/ LCD remote control ON/Off and other parameters, suitable compressor, fan motors with fan/blower, DX cooling coil, air filter, safety Controls/overload protection ,electrical wiring, first charge of Refrigerant (Non CFC) and Oil etc with 3 star BEE rating suitable for working on single phase 230V,50Hz power supply etc. complete in all respect. Make: Bluestar/ Hitachi/ Llyod

S&F factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way TPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link including MCCB TPN 100 Amp, 25KA as incomer & MCB SP 32/40 Amp of 10 KA capacity of 16 Nos as out going complete all as specified & directed.

MRITUNJYA ASSOCIATES (BID ID -3123901)

M/S Rohit Enterprises (BID ID -3123850)

BEHAL TRADERS (BID ID -3138205)