REPAIR AND MAINT OF DG SETS AND CONNECTED ITEMS AND REPAIR/ REPLACEMENT OF LT FEEDER PILLAR/ ENERGY METER PANEL AT CME

Amount

M/L for Maintenance, servicing and attending faults on call basis of standby DG Set complete including draining out of diesel from tank , cleaning the tank thoroughly and refilling the drained out diesel, draining out engine oil from the sump, cleaning the sump thoroughly and refilling the sump with new engine oil to it’s required level, replacing the fuel filter, lubricating oil filter, clean air cleaner, change air cleaner elements, and check coolant level & make up the same,drain the fuel filter & water separator, filling the starting batteries with electrolyte/distilled water to maintain the required specific gravity, replace the u/s brass connectors for batteries, cleaning of battery terminals & applying petroleum jelly to battery terminal posts & brass connectors, including M & L for V Belts, checking of exhaust leakage, governor, breathers, hose pipes with clips, diesel pipes, thermostat valve, solenoid switch, tappet setting, oil filter element, air filter, bypass filter etc and adjust/set the same for proper functioning of DG Set, checking of fuel, oil and water/ coolant level etc, adjusting and keeping the fan belts to the desired tension, tightening all the bolts and nuts to the required torque etc, cleaning the DG Set with accessories

ITEM NO. 1. CONTD... as prescribed by the manufacturer and test for satisfactory running of DG set for two hour at connected load and record shall be made in respect of RPM, oil pressure, oil temperature, coolant temperature, voltage, frequency, load current, battery charging, fuel consumption etc complete all as specified and directed by Engineer in Charge for 12.5/15/20/25 KVA DG SET. Make :- Crompton Greaves/ Kirloskar Note :- (a). Engine oil for refilling will be paid separetely. (b). Coolant for make up will be measured & paid separately (c). Testing will be carried out in presence of Engineer - in - charge and DHPP consumption will be entered in PRRB. (d). The Make of Fuel filter , Oil Filter , V belt & other above mentioned components will be as per manufacturers recommendations (rate of fuel filter, oil filter, air filter (primary and secondary), V belt and other mentioned items are inclusive in quoted rate.) (e) Checking of all electricial systems, wiring , connections of battery, battery charging,etc during servicing. (f) Maintenance and servicing of DG sets to be carried out twice throughout the CA duration (for item No 01 to 07) (Rates are inclusive for two servicing). (g) Parts replaced will be contractor's responsibility during the one year CA period and also no claim whatsoever will be entertained for payment if any part is replaced again during the CA period. (h) Attending to faults on call basis will not be considered as servicing. Also, parts replaced as part of servicing BOQ item is inclusive in rate despite changing it after servicing, hence contractor should quote the rates accordingly. (i) After servicing checklist as per OEM (printed ) duly signed by Contractor and servicing agency to be submitted to EIC without fail.

All as per item No.1 here-in-before, but for 50/62.5/63 KVA DGSet. Make :- Crompton Greaves/ Kirloskar

All as per item No.1 here-in-before, but for 100/125 KVA DGSet. Make :- Crompton Greaves/ Kirloskar/Mahindra

All as per item No.1 here-in-before, but for 160 KVA DG Set. Make :- Crompton Greaves/ Kirloskar

All as per item No.1 here-in-before, but for 200/250 KVA DG Set. Make :- Crompton Greaves/ Kirloskar

All as per item No.1 here-in-before, but for 320 KVA DGSet. Make :- Crompton Greaves/ Kirloskar

Supply and topping up of best quality antifreezing, inhabitor (Coolant) liquid for DG Set of various capacity and locations complete all as specified and directed.

Supply only engine oil, multi grade 20w / 40 Make :- Indian oil / Hindustan petroleum / Castrol / BPCL.

Repair & Maintenance of existing canopy of eco friendly DG Set of any capacity, cleaning of internal & external parts, tightening of loose parts, painting of rusted area, replacing of unserviceable door locks and keys, replacing of damaged or burned inside sponge insulations,fixing of additional steel sheet for area where canopy area is corroded complete all as specified and directed

Material and labour in replacement broken MS Hinges suitable for Canopy door for any type/capacity of DG Sets (as per sample).

M&L for cleaning of diesel tank of DG set of capacity 12.5 to 25 KVA, replacement of diesel measurement scale including painting the tank with one coat of synthetic enamel paint complete all as specified and as directed. Note: Quoted rates are included for opening of DG set canopy for removing of fuel tanks which are provided bottoms base plate of DG sets and if reqd some welding or fabrication work.

Description all as per item No.11 here -in-before, but for 50 KVA to 100 KVA DG Sets

Description all as per item No. 11 here -in-before, but for 125 KVA to 160 KVA DG Sets

Description all as per item No 11 here -in-before, but for 200 KVA to 250 KVA DG Sets

Description all as per item No. 11 here -in-before, but for 320 KVA DG Sets

Repairs of radiator assembly by dismantling from engine and removing the sediments and scales, corrosion etc by means of descaling chemical cleaning and high pressure water washing and air cleaning, gas welding / soldering with good quality material for stopping the leakage etc, re-assembling the same with new gaskets, fixing to the engine with hoses, clips complete to the entire satisfaction of engineer - in - charge as required for following DG Sets. Note: Rate also includes transportation to the workshop and fabrication if reqd

12.5/15/20/25 KVA DG Set

50/62.5/63 KVA DG Set

100/125/160 KVA DG Set

200/250 KVA DG Set

320 KVA DG Set

Material and labour for repairs/ replacement of turbo charger including replacement of charger kit with all unserviceable parts and testing after completion for all DG Sets, complete all as specified and as directed.

12.5/15/20/25 KVA DG Set

50/62.5/63 KVA DG Set

100/125/160 KVA DG Set

200/250 KVA DG Set

320 KVA DG Set

Dismantling the fly wheel coupling between engine and alternator and Supply and replace complete set of bullet rubber bushes, coupling nuts & bolts including proper alignment of engine & alternator for smooth running for DG set of capacity complete all as specified and directed by Engineer-in-Charge of he following capacity.

12.5/15/20/25 KVA DG Set

50/62.5/63 KVA DG Set

100/125/160 KVA DG Set

200/250 KVA DG Set

320 KVA DG Set

Material and labour for cross arms, bracing supports, clamps fabricated out of structural steel such as ISMC, angle iron, flat iron sections including hot galvanised nuts & bolts, washers for single and two pole structure welding, bending cold or hot, drilling holes for bolts, in any shape or size as specified and including of one under coat and finishing coat with aluminium paint over a coat of red oxide primer. Note: Fabrication,welding and transportation is inclusive in the rate itself.

M&L for servicing of alternator of any make suitable for DG set by opening the end cover, cleaning the dust and rust formed over the terminals, cleaning with CTC liquid, checking of diodes, winding, isolating transformer and AVR panel and rewinding of stator/rotor with super enamelled copper wire applying Dr. beck paint for insulation improvement over the strips/ winding and drying till getting sasfactory insulation resistance complete, refixing the covers including testing complete all as specified and directed. Note: Quoted rate includes disconnecting all connected parts, transportation to workshop and return back from the workshop for refitting in original position.

12.5/15/20/25 KVA DG Set

50/62.5/63 KVA DG Set

100/125/160 KVA DG Set

200/250 KVA DG Set

320 KVA DG Set

M&L for calibrating of diesel engine by disconnecting, dismantling of FIP, injector nozzles including connected accessories and refixing after required repairs, etc. complete all as specified and as directed Notes: (i) Injector nozzle, plunger, delivery valves only if found unserviceable and are replaced for proper functioning, the same will be measured and paid separately under respective items here-in-after. (ii) All any other items required for making the FIP serviceable shall be deemed to be included in the quoted rate

Supply only injector nozzle suitable for 12.5/15/20/25 kVA DG set.

Supply only injector nozzle suitable for 50/62.5/63 kVA DG set

Supply only injector nozzle suitable for 100/125/160 kVA DG set

Supply only injector nozzle suitable for 200/250 kVA DG set

Supply only injector nozzle suitable for 320 kVA DG set

Supply only plunger suitable for 12.5/15/20/25 kVA DG set.

Supply only plunger suitable for 50/62.5/63 kVA DG set

Supply only plunger suitable for 100/125/160 kVA DG set

Supply only plunger suitable for 200/250 kVA DG set

Supply only plunger suitable for 320 kVA DG set

Supply only delivery valves suitable for 12.5/15/20/25 kVA DG set.

Supply only delivery valves suitable for 50/62.5/63 kVA DG set

Supply only delivery valves suitable for 100/125/160 kVA DG set

Supply only delivery valves suitable for 200/250 kVA DG set

Supply only delivery valves suitable for 320 kVA DG set

M&L for repair/overhauling of self starter incl. replacement of carbon brushes, bearing, bushes, rewinding of armature and field etc. and varnishing complete all as directed for the following capacity :-

24 Volts make- Lucas or as per generator

12 Volts Make-Lucas or as per generator

M & L for repairing of battery charging alternator engine mounted with replacement of any of the unserviceable part such as rectifier with voltage regulator, diode plate , carbon brushes for the following capacities and as directed by engineer-In- Charge :-

24 volts capacity

12 volts capacity

Repair/Replacement of 12/24 volt Battery 100 AH high capacity plates ensure higher cranking power of weight ratio works in temperature range - 18° C to 55° C , balanced 'Active' materials ensure superior cranking currents with instant start of your Genset, Surdy PPCP containers for durability, designer calcium lead alloys for positive plates & negative plates for maintenance-free characterestic requires topping-up only once in 6 months and heavy duty pillar & terminal to withstand heavy current all as specified and directed by Engineer-in-charge.

Description all as per item No 39 here -in-before, but of capacity 150 AH

Description all as per item No 39 here -in-before, but of capacity 180 AH

Material and labour for reconditioning 12 V 180 AH, 24 plates Batteries including replacement with new parts such as –ve & +ve plates, PVC separators, terminal post, Acid and distilled water etc making in serviceable conditions, all as specified and directed.

Description all as per Item No. 42 above, but 12 Volts 100/150 AH, 24 Plate battery.

M & L MCB 4P pole 240 volts 10 KA, rating 40 Amps 'C' seris

S&F following items including taking out old unserviceable MCCB's/MCB's:- Note:- Icu=100%Ics for MCCB's Make: L&T/Havells/Schneider/ABB

MCB 6-32 Amps, SPN, suitable for 240 volts, 50 Hz, AC

MCCB, 63 Amps, four pole,16 KA, 415 volt

MCCB, 100 Amps, four pole,16 KA, 415 volt

MCCB 125 Amps, four pole, 25 KA, 415 volt

MCCB, 160 Amps, four pole, 25 KA, 415 volt

MCCB, 200 Amps, four pole, 25 KA, 415 volt

MCCB, 250 Amps, four pole, 25 KA, 415 volt

MCCB, 400 Amps, four pole, 36 KA, 415 volt

M&L for taking out old unserviceable Change over switch and supply and fix new auto transfer switch[ATS] with automatic/Manual control with inbuilt time delay etc complete with enclosure 400 Amp 4 pole including necessary arrangements to fix the ATS on wall with necessary bus bar and cable end boxes to connect incoming cable and out going cables complete [Make- Havells Instaline 8537 or equivalent in all respect such as construction, functioning etc of L&T/Schneider]

Description all as per item No. 46 above, but of current rating 315 Amps

Description all as per item No. 46 above, but of current rating 250 Amps

Description all as per item No. 46 above ,but of current rating 200 Amps

Description all as per item No. 46 above, but of current rating 100 Amps

Taking out following defective parts from Alternator of DG sets and supply and fixing new parts including testing complete all as directed by Engineer-in-Charge :-

AVR unit complete for 12.5/15/20/25 KVA DG Set

AVR unit complete for 50/62.5/63 KVA DG Set

AVR unit complete for 100/125/160 KVA DG Set

AVR unit complete for 200/250 KVA DG Set

AVR unit complete for 320 KVA DG Set

Terminal plate

M & L Silicon Rectifier assembly with metallic plate as existing covered with thin layer of selnium and insulated nut bolt, control wiring soldering complete

M & L Field excitation unit three phase 415 V for alternator

M & L Flexible rubber coupling star type capacity alternator coupled with engine Make : Kirloskar/Crompton Greaves for 50/62.5/63 KVA

M & L Flexible rubber coupling star type capacity alternator coupled with engine Make : Kirloskar/Crompton Greaves/Mahindra for 100/125/160 KVA

M & L Flexible rubber coupling star type capacity alternator coupled with engine Make : Kirloskar/Crompton Greaves for 200/250 KVA

M & L Flexible rubber coupling star type capacity alternator coupled with engine. Make : Kirloskar/Greaves/Cummins for 320 KVA

M & L Carbon brushes set of four

M & L Slip rings (Four rings)

Material and labour for repair and calibration of PT Pump as per calibration procedure and norms for DG Set installation and testing of the same after completion, complete all as specified and as directed.

12.5/15/20/25 KVA DG Set

50/62.5/63 KVA DG Set

100/125/160 KVA DG Set

200/250 KVA DG Set

320 KVA DG Set

Material & labour for Earthing complete using copper earth plate electrode of size 60cm X 60cm X 3.15mm thick burried directly in ground vertically at a depth not less than 2.25 m below normal ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level, earth plate surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using copper strip of size 20 x 3 mm by means of bolts, nuts, check nuts and washers made of copper and protected by light grade 40 mm dia galvanised iron pipe and GI pipe light grade 20mm bore for watering, including funnel, wire mesh, CI pit cover and PCC chamber pit with PCC 1:2:4 type B-2 (including necessary excavation and earth work disposal of surplus soil to a distance not exceeding 50 m all as specified and shown on electrical plate No 3 of SSR Part-I 2009 and testing on completion all as specified and directed.

Supply and fill/top up the distilled water of 01 ltr packing in the battery complete all as specified

S&F PVC insulated copper conductor cable 25 Sqmm single core, of 2 mtr length, solidered with 2 nos gunmetal battery terminals suitable for 100-180 Ah 12v/24volt DC battery complete all as specified and directed.

Dismantling of exising old foundation of DG sets and M&L for cement concrete type C2 1:3:6 (40mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams: plinth beams, bases for columns, etc : basement slabs, under-reamed piles and mass concrete, using mild seel TMT bars 10 mm dia and over, cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, flat formwork to sides of concrete foundations, footing, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works vertical or to batter including excavaion returning and filling removing all as specified and directed by Engineer-in-Charge. Note: Quoted rate includes lifting of DG set with crane to safe place and again placing on plinth after completion. Contactor shall submit detailed drawing of the plinth to EIC and proceed after the approval only.

Dismantling of old coverd shed of DG Sets and M&L for hardcore of brocken stone of guage exc 63 mm but not exceeding 100mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, cement concrete type C2 1:3:6 (40mm graded stone aggregate) as in foundation filling and mass concrete, cement concrete type A-1:1 5:3 (using 20mm graded stone aggregate), 150mm thickness as in hardstandings, fixing of new roof trusses (framed ), trussed,purlins,crane gantries, rails and fastning and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, replacement with new pre-painted galvalume aluminiium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, preparation of steel surface and applying one coat of red oxide zinc chrome primer and two coats of Epoxy anticorrosive paint over 10 cm width or girth including excavation returning, filling, removing and connected jointing and fabrication work all as specified and directed by Engineer-in-Charge. Note:- Shed area should cover min. 02 metre beyond the DG plinth and height min. 2 metre from chimney top point.

Voltmeter 0-500 V

Ammeter 0-200 A / 0-100 A

CT cast resin type of suitable size

Aluminium Busbar as per existing

Cable lugs as per existing

Battery charging circuit suitable for 12V/24V, DC in existing DG set panel board including addition/ alteration in wiring system complete.

Time delay relay of suitable size

PCB assy complete with updated software and wiring

S & F in repair Power contactor 415v, 50Hz, AC suitable for following DG set Control panel / AMF Panels for the following capacities and as directed by Engineer-in-Charge.

D. G . Set 12.5/15/20/25/50/63 KVA

D. G . Set 100/125/160 KVA

D. G . Set 200/250 KVA

D. G . Set 320 KVA

S&F in repairs MS pipes 15mm dia suitable for Diesel incl necessary excavation etc complete all as specified and as directed

M & L for Top Overhauling only of DG set of following capacity of Kirloskar/Cummins or any make and including replacement of gaskets etc complete all as specified and all spare parts required to complete the work to the satisfaction of Engineer-in-charge .

D. G . Set 12.5/15/20/25/50/63 KVA

D. G . Set 100/125/160 KVA

D. G . Set 200/250/320 KVA

Supply only Oil Sump packing set suitable for following DG sets :-

D. G . Set 12.5/15/20/25/50/63 KVA

D. G . Set 100/125/160 KVA

D. G . Set 200/250/320 KVA

Supply and fix solenoid valve suitable for following capacity DG sets for smooth functioning of DG sets complete to the satisfaction of Engineer-in-Charge :-

D. G . Set 12.5/15/20/25/50/63 KVA

DG Set 100/125/160 KVA DG set

DG Set 200/250/320 KVA DG sets

Supply and fix single phase preventer suitable for operation on 415 volt 50 HZ AC supply (Make- L&T/Minilec)

Supply and fix microprocessor based multifunction relay suitable for DG sets operation and showing the various parameters such as Volt, ampere, frequency, RPM etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs fuse base suitable for cylindrical / DIN fuse link for following capacities and all as directed by Engineer-in-Charge

160 Amps capacity ( L&T/Schneider/Siemens/C&S)

250 Amps capacity ( L&T/Schneider/Siemens/C&S)

DIN type HRC fuse link type HN of capacity 125 Amps

DIN type HRC fuse link type HN of capacity 160 Amps

DIN type HRC fuse link type HN of capacity 200 Amps

DIN type HRC fuse link type HN of capacity 250 Amps

Material & labour for Earthing complete using galvanised iron earth plate electrode of size 60cm X 60cm X 6mm thick burried directly in ground vertically at a depth not less than 2.25 m below normal ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level, earth plate surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using galvanised iron strip of size 32X6 mm by means of bolts, nuts, check nuts and washers made of GI and protected by light grade 40 mm dia galvanised iron pipe and GI pipe light grade 20mm bore for watering, including funnel, wire mesh, CI pit cover and PCC chamber pit with PCC 1:2:4 type B-2 (including necessary excavation and earth work disposal of surplus soil to a distance not exceeding 50 m all as specified and shown on electrical plate No 3 of SSR Part-I 2009 and testing on completion all as specified and directed.

Supply and fix earth continuity conductor fixed to wall or burried in ground or fixed to pole or any other indicated situation, made out of galvanised iron strip of size 32x6 mm complete all as specified and directed.

Note: Contractor shall get the drawings of Panel approved by EIC and also CPRI approval of the panel firm to be submitted to EIC.

Supply, laying XLPE insulated PVC FRLS, screened , PVC bedded and PVC tape sheathed galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of following sizes including taking out old un-serviceable cable complete all as specified and directed.

4 core 16 Sq mm

4 core 25 Sq mm

3.5 core 35 Sq mm

3.5 core 50 Sq mm

3.5 core 70 Sq mm

3.5 core 95 Sq mm

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.5m x 0.5m x 1.0m) factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 50x50x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 50x50x5mm & housed with the following accessories:-

Copper bus bar rectangular 400 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01Job

MCCB 250 Amps, 4 pole 415 Volts, 50 Hz ,50 KA, thermal magnetic release adjustable type- 01 No ( Incoming)

MCCB 125 Amps, 4 pole, 415 Volts, 50 Hz ,25 KA, thermal magnetic release adjustable type - 04 Nos ( Outgoing)

MCCB 100 Amps, 4 pole, 415 Volts, 50 Hz ,25KA, thermal magnetic release adjustable type - 01 No ( Outgoing)

RYB LED phase Indicator Lamp set - 01 No

Provision of cubicle as per above description to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.2m x 0.5m x 1.0m) factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 50x50x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 50x50x5mm & housed with the following accessories:-

Copper bus bar rectangular 400 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01Job

MCCB 250 Amps, 4 pole 415 Volts, 50 Hz ,50 KA, thermal magnetic release adjustable type- 01 No ( Incoming)

MCCB 160 Amps, 4 pole, 415 Volts, 50 Hz ,25 KA, thermal magnetic release adjustable type - 03 No ( Outgoing)

MCCB 125 Amps, 4 pole, 415 Volts, 50 Hz ,25 KA, thermal magnetic release adjustable type - 01 No ( Outgoing)

RYB LED phase Indicator Lamp set - 01 No

Provision of cubicle as per above description to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.2m x 0.5m x 1.0m)factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 50x50x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 50x50x5mm & housed with the following accessories:-

Copper bus bar rectangular 400 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01Job

MCCB 250 Amps, 4 pole 415 Volts, 50 Hz ,50 KA, thermal magnetic release adjustable type- 01 No ( Incoming)

MCCB 125 Amps, 4 pole, 415 Volts, 50 Hz ,25 KA, thermal magnetic release adjustable type - 04 Nos ( Outgoing)

RYB LED phase Indicator Lamp set - 01 No

Provision of cubicle as per above description to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.0m x 0.5m x 1.0m)factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 40x40x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 40x40x5mm & housed with the following accessories:-

Copper bus bar rectangular 200 Amps full for phase and half for neutral mounted on epoxy insulators with colour coding PVC sleeves.-01 Job

MCCB TPN 415 Volts 50 Hz 25 KA 100 Amps - 01 Incommer

RYB LED Indicator Lamp- Set of Three-01

3 pole Power contactor 415 Volts, ML - 4, 70 Amps cap - 01

Digital street light timer type - 1 No

MCB SPN 40 Amps :- 03

Provision of cubicle to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.2m x 0.5m x 1.0m) factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 50x50x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 50x50x5mm & housed with the following accessories:-

Copper bus bar rectangular 300 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01Job

MCCB 160 Amps, 4 pole 415 Volts, 50 Hz ,50 KA, thermal magnetic release adjustable type- 01 No ( Incoming)

MCCB 100 Amps, 4 pole, 415 Volts, 50 Hz ,25 KA, thermal magnetic release adjustable type - 03 No ( Outgoing)

RYB LED phase Indicator Lamp set - 01 No

Provision of cubicle as per above description to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Taking out old unserviceable LT panel and supply, installation, testing & commissioning, dust, weather & vermin proof L.T feeder pillar box (approx size 1.2m x 0.5m x 1.0m) factory fabricated (panel shall be got manufactured from any manufacturer duly approved by CPRI) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 50x50x5 mm suitable for operation on 3 phase 4 wire, 440V 50 Hz system, with hinged panel doors on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed to inclusive of PCC foundation, angle iron legs of 50cm above ground level made of angle iron 50x50x5mm & housed with the following accessories:-

Copper bus bar rectangular 400 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01Job

MCCB 250 Amps, 4 pole 415 Volts, 50 Hz, 50 KA, thermal magnetic release adjustable type- 01 No ( Incoming)

MCCB 125 Amps, 4 pole, 415 Volts, 50 Hz, 25 KA, thermal magnetic release adjustable type - 03 Nos ( Outgoing)

3 pole Power contactor 415 Volts, ML - 4, 70 Amps cap - 01

Digital street light timer type - 1 No

MCB SPN 40 Amps :- 03 Nos

RYB LED phase Indicator Lamp set - 01 No

Provision of cubicle as per above description to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 400 Amps 415 AC, 50 Hz, 50 kA thermal magnetic release adjustable type complete all as specified and directed. Make : Indoasian /L&T/Legrand

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 250 Amps 415 AC, 50 Hz, 36 kA thermal magnetic release adjustable type complete all as specified and directed. Make : Indoasian /L&T/Legrand

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 100 Amps 415 AC, 50 Hz, 36 kA thermal magnetic release adjustable type all as specified and directed. Make : Indoasian /L&T/Legrand

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 125 Amps 415 AC, 50 Hz, 36 kA thermal magnetic release adjustable type complete all as specified and directed. Make : Indoasian /L&T/Legrand

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 160 Amps 415 AC, 50 Hz, 36 kA thermal magnetic release adjustable type complete all as directed. Make : Indoasian /L&T/Legrand

Material & Labour for replacement of old UNSV MCCB of any type/capacity with new MCCB FP 63 Amps 415 AC, 50 Hz, 25 kA thermal magnetic release adjustable type complete all as specified and directed. Make : Indoasian /L&T/Legrand

M & L for Preparation of old painted surfaces of LT Panel or Street light Panel covered by dust and other deposited materials by cleaning from Panel of Size (approx 1.2 x 0.5 x 1.0m) including repair of panel door, hinged nut bolts, clamp etc and painting with one coat of synthetic enamel paint of existing colour paint complete all as specified and directed. Note : Size of panel may be differ, no extra shall be paid for painting of extra size panel as specified in item.

Supply and fixing in replacement three pole Contactor current Rating 70 A General use 10A, 415V with coil Make L&T Model MNX 70 Three pole contactor complete all as specified and directed. Make: L&T cat part No CS97076/Legrand/Schneider

Supply and fixing in replacement MNX 50 to 80 spare coil for three pole Contactor complete all as specified and directed. Make : L&T cat part No CS96318/Legrand/Scheider

Supply and fixing in replacement Digital timer switch with inbuilt backup current capacity 16 Amp operated on 415 volts AC 50Hz complete all as specified and directed. Make: Indoasian cat part No TDA43111/ Legrand/ Schneider

M & L for earthing complete with 600x600x60mm GI earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including GI strip of size 25x4mm by means of bolts, nuts and check nuts and washers with and including 40mm dia GI medium grade pipe for protection strip to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoaldust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including chamber made up of PCC 1:2:4 type-B1 with M.S angle iron frame, C.I. Cover, 20mm dia light grade G.I. pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed. Note :- GI strip more than 7.5 mtr will be measured and paid separately.

Supply and fixing in replacement existing Aluminium bus bar rectangular 400 to 600 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators including nut, bolts with colour coding PVC sleeves complete all as specified and directed.

Supply and fixing in replacement existing Aluminium bus bar rectangular 250 to 300 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators nut, bolts with colour coding PVC sleeves complete all as specified and directed.

Supply and fixing in replacement Aluminium lugs of size 16 Sqmm to 50 Sqmm and tightening of all connecting points, cable connection complete all as specified and directed by Engineer-in- Charge

Supply and fixing in replacement Aluminium lugs of size 70 Sqmm to 120 Sqmm and tightening of all connecting points, cable connection complete all as specified and directed by Engineer-in- Charge