Special repair of Sub Health Centre at Village Gharoot in Palwal Distt.

Amount

Civil & P.H. Works

12mm thick cement plaster on walls (1:6). (HSR 15.7)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81). Through Rate

supplying and fixing glass panes with moulding of commercial hard wood such as hillock champ, chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned) (HSR 17.36 (b)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (i) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (c) decorative veneering with vertical grain cross bands and face veneer on both sides teak facing and edges lipped with commercial hard wood with laminated core:- Duro, Green Only. [HSR 17.93 - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (iii) (HSR 17.93a iii

Wrought iron and mild steel (using angles, flats, square bars, tees and channels), ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3). Through Rate

Distempering with washable oil bound distemper (of approved manufacture) two coats on Old Distempered work (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge).(HSR 16.60).

Providing and Applying Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 Mtrs. (HSR 6.6)

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth. (HSR 10.28)

First class brick work laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

Earth work non plastic or Tibba Sand under floors/Road & Parking taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. (For any lead and lift). [NS].

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation and plinth. (HSR 10.39)

Conglomerate Floor 40mm thick cement concerete 1:2:4 topping as per (HSR 14.9)

Providing and laying 80 mm thick ISI marked internlocing paver paver blocks conforming to IS 15658:2006/IRC:SP:63-2004 of all Shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159). (Note:- Reputed make Paver Block Only ISI marked will be used as approved by Engineer-in-charge).

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (b) Size 630 mm (ii) Single Colour. (Make Hindware) (HSR 30.2 b ii)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (HSR 30.12) (i) white

Providing and fixing in position best Indian make flat back or angular lipped front urinal 465 mm high consisting of :-(HSR 30.19i) Flat back lipped or angular urinal basin of vitreous china ware (to the approval of Engineer-in-charge)5 liters capacity mosquito proof Indian make C.I automatic flushing cistern, painted with non-yellow white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15mm pipe.Pair of R.S or C.I painted brackets and brass couplings Standred size G.I flush pipe with C.P brass wall clips and unions complete including cutting and making good the walls and floor and painting o fittings etc (as required by the Engineer-in-charge)i)White

Providing and fixing 25mm thnick marble partitions for different type of urinals (HSR 30.40) (B) (II) (i) vetreous Chinaware Partition plate

Providing and fixing in position best India make towel rails fixed in with rawlslugs embedded in walls with CP Brass screws, Complete in all respect including cutting and making goods the walls etc. (HSR 30.68) (d) CP Brass Two swivel towel rail 400mm longh

Providing and fixing in position best Indian make Soap dis fixed into wall with C.P. brass screws and complete in all respects including cutting and and making goods the walls etc (HSR 30.70) (d) Vitreous Chinaware recessed soap dis with hand rails (iii) Mixed Colour

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (a) Bib cock long body (HSR 30.75)

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) a) 15mm stop cock(HSR 30.76) i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully decribed in item no 30.41 above (HSR 30.42) R.S or C.I brackets for building into wall including painting32 mm C.P brass waste with C.P brass chain and rubber plug 15 mm C.P brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-charge) All fittings best Indian make and; to the approval of the Engineer-in-chargeAll brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc. Size 530mmx430mm with one no. tap

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. 500 Ltr. Cap. (HSR 30.119)

1000 Ltr Capacity

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal Work - Exposed on Wall. [DSR 18.10). (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

(iii) 25 mm internal diameter of pipeline

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) (b) 20 mm nominal bore

(c) 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (HSR 14.62)

Rajat Sehrawat

JS Construction