Construction of CMD Residence at plot no. 69, Golf Links, New Delhi

BILL OF QUANTITY

Digitally signed by SANGRAM

PROJECT : CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

S.N DESCRIPTION AMOUNT (DSR) AMOUNT (NS) AMOUNT (DSR+NS)

2 CIVIL, INTERIOR WORKS, LANDSCAPE & HORTICULTURE WORKS 76,63,301.73 81,93,039.94 1,58,56,341.67

6 PLUMBING & SANITARY WORKS 10,49,289.70 21,55,712.14 32,05,001.83

SUB TOTAL (in INR) ₹ 3,66,29,160.11

Digitally signed by SANGRAM

PROJECT : CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

BOQ- STRUCTURE WORKS

DSR-2023 Sr. No. Description Unit Qty - Qty : Total Rate Amount

Building Landscape Qty DSR Rate NS RATE

DSR Rate Cess factor (incl (incl 18% DSR Amount (in Rs) NS AMOUNT (in Rs)

1.0 EARTH WORKS & SITE CLEARANCE

2.6 1.1 Earth work in excavation by mechanical means (Hydraulic

xcavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m

in width as well as 10 sqm on plan) including getting out and disposal

of excavated earth lead upto 50 m and for all lift, as directed by

Engineer-incharge.

2.25 1.2 Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up

to 50 m and lift upto 1.5 m.

2.26 1.3 Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

2.27 1.4 Supplying and filling in plinth with sand under floors, including

watering, ramming, consolidating and dressing complete.

2.34 1.5 Supplying chemical emulsion in sealed containers including delivery as

2.34.1 1.5.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 15.50 15.50 234.75 0.97 1.03 235.26 3646.59

Anti termite treatment

2.35 1.6 Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) :

2.35.3 1.6.1 Treatment of soil under existing floors using chemical emulsion @ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes

and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to

match the existing floor:

2.35.3.1 1.6.1.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 155.40 155.40 310.05 0.97 1.03 310.73 48287.29

2.31 1.7 Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height of

1 m above ground level and removal of rubbish up to a distance of 50

m outside the periphery of the area cleared.

4.0 2.0 CONCRETE WORKS

4.1 2.1 Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth

4.1.8 2.1.1 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

sources : 8 graded stone aggregate 40 mm nominal size derived from Cum 22.15 12.00 34.15 6812.00 0.97 1.03 6826.92 233118.78

natural sources)

4.17 2.2 Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone- III) derived from natural sources : 6

graded stone aggregate 20 mm nominal size derived from natural

sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, Sqm 65.00 65.00 749.30 0.97 1.03 750.94 48811.16

well rammed and consolidated and grouted with fine sand, including

necessary xcavation, levelling & dressing & finishing the top smooth.

5.0 3.0 REINFORCED CEMENT CONCRETE WORK

5.9 3.1 Centering and shuttering including strutting, propping etc. and removal

of form for Digitally signed by SANGRAM

5.9.1 3.1.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 49.34 49.34 392.15

DSR-2023 Sr. No. Description Unit Qty - Qty : Total

Building Landscape Qty DSR Rate NS RATE

DSR Rate Cess factor (incl (incl 18% DSR Amount (in Rs) NS AMOUNT (in Rs)

5.9.2 3.1.2 Walls (any thickness) including attached pilasters, butteresses, plinth

and string courses etc.

5.9.3 3.1.3 Suspended floors, roofs, landings, balconies and access platform Sqm 391.44 391.44 927.25 0.97 1.03 929.28 363757.63

5.9.5 3.1.4 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 269.09 269.09 736.40 0.97 1.03 738.01 198591.84

5.9.6 3.1.5 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 515.20 515.20 961.30 0.97 1.03 963.41 496346.38

5.9.7 3.1.6 Stairs, (excluding landings) except spiral-staircases Sqm 56.00 56.00 764.95 0.97 1.03 766.63 42931.01

5.9.13 3.1.7 Vertical and horizontal fins individually or forming box louvers band,

facias and eaves boards

5.9.16 3.1.8 Edges of slabs and breaks in floors and walls

5.9.19 3.1.9 Weather shade, Chajjas, corbels etc., including edges Sqm 11.22 11.22 951.10 0.97 1.03 953.18 10694.71

5.11 3.1.10 Extra for additional height in centring, shuttering where ever required

with adequate bracing, propping etc. including cost of de-shuttering

and decentring at all levels,over a height of 3.5 m, for every additional

height of 1 metre or part thereof (Plan area to be measured)

5.11.1 3.1.10.1 Suspended floors, roofs, landing, beams and balconies (Plan area to

5.22 3.2 Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 3.2.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 5485.71 5485.71 107.85 0.97 1.03 108.09 592929.50

5.22A 3.3 Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

5.22A.6 3.3.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 17491.66 17491.66 107.85 0.97 1.03 108.09 1890606.48

5.33 3.4 Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate

/ retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of

centering, shuttering, finishing and reinforcement as per direction of

the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified minimum

cement content, the contractor shall have discretion to either re-design

the mix or bear the cost of extra cement.

5.33.1 3.4.1 All works upto plinth level

5.33.1.1 3.4.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum

5.33.1.2 3.4.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum

5.33.2 3.4.2 All works above plinth level upto floor V level

5.33.2.1 3.4.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum

5.33.2.2 3.4.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum

10.0 4.0 STEEL WORK

10.2 4.1 Structural steel work riveted, bolted or welded in built up sections,

trusses and framed work, including cutting, hoisting, fixing in position

and applying a priming coat of approved steel primer all complete. Digitally signed by SANGRAM

DSR-2023 Sr. No. Description Unit Qty - Qty : Total

Building Landscape Qty DSR Rate NS RATE

DSR Rate Cess factor (incl (incl 18% DSR Amount (in Rs) NS AMOUNT (in Rs)

22.0 5.0 WATER PROOFING

NS-1 5.1 Providing and laying water proofing treatment to vertical and horizontal

surfaces of depressed portions of W.C., kitchen and the like consisting

of :(Sunken Areas, toilet (Cementitious coating)

5.1.1 Two coats of 2 component polymer modified cementations coating and

details as per technical specification.

NS-2 5.2 Terrace waterproofing :- 2 component liquid applied, high build

elastomeric polyurethane waterproofing coating details as per technical Sqm 82.00 82.00 1918.80 157341.44

NS-3 5.3 Tanks Water Proofing with Cementitious coating

5.3.1 3 coats of two component polymer modified cementitious coating and

details as per technical specification.

NS-4 5.4 Shaft Waterproofing :- Two coats of 2 component polymer modified

cementations coating and details as per technical specification Sqm 78.00 78.00 1233.51 96214.01

followed by water proofing paint

Digitally signed by SANGRAM

PROJECT : CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

BOQ INTERIOR & LANDSCAPE WORKS

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with

150mm/200mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum

conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band

at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete

as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made

for seperately).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with

Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure

6.38 1.2 above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate CUM 18.00 18.00 10195.45 0.97 1.03 10217.78 183920.00

includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry

1.3 Internal Plaster

a Cement Plaster

13.4 i) 12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand) SQM 272.00 272.00 357.35 0.97 1.03 358.13 97412.07

13.16 ii) 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) SQM 26.00 26.00 300.45 0.97 1.03 301.11 7828.81

b Gypsum Plaster

Providing and applying premixed formulated one coat gypsum lightweight plaster having additives

and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II)

13.78 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling

at all floors and locations, finished in smooth line and level etc. complete.

1.4 External Plaster

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse

13.12 a sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). SQM 233.00 217.00 450.00 537.45 0.97 1.03 538.63 242382.16

13.16 b 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) SQM 41.00 41.00 300.45 0.97 1.03 301.11 12345.43

Saucer Drain :- Providing and fixing of Saucer Drain along the sides of Paved area in min M-30

grade cement concrete complete and provide proper slopes to drain of rain water including all lead,

lifts etc complete . (Note :-Rate is inclusive of excavation for saucer drain. )

Providing & laying at or near ground level factory made cement concrete kerb stone of M-25 grade

cement concrete in position to the required line, level and curvature, jointed with cement mortar

1:3(1cement: 3coarse sand), including making joints with or without grooves ( thickness of joints

except at sharp curve shall not be more than 5mm), including making drainage opening wherever

required complete etc. all cmplete as per direction of Engineer-in-Charge. Precast C.C kerb stone

shall be approved by Engineer-in-Charge.0

2 False Ceiling Works

POP CEILING ; Providing and making POP Ceiling with GI section of 0.55 mm thick having web of

51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with

help of connecting clips and in direction perpendicular to the intermediate channel with centers of

300 mm, entire surface to be cover with rabbit wire mesh fixed to GI Frame and applied POP Puning

over the mesh web in even level till dry, cost also include the split level, curve design, cove,

cornince, as per design and drawing or as per directions of Project-in-Charge. No Extra payment

shall be payble for any vertical, bulkhead,lights & services cutting etc.

3 Painting Work

3.01 Internal Painting

Premium Acrylic Emulsion Paint:- Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even shade and

13.44 b Cement Paint :- Finishing walls with waterproofing cement paint of required shade.

New work (Two or more coat applied @ 3.84 Kg/10 sqm SQM 78.00 78.00 116.90 0.97 1.03 117.16 9138.17

Digitally signed by SANGRAM

3.2 External Painting SINGH

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

13.45 a Finishing walls with Textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior

primer applied @ 2.20kg/10 sqm

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content

Wall & Ceiling :- With water thinnable cement primer on wall & Ceiling surface having VOC content

less than 50 grams/litre

3.4 Putty Work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

13.80 a manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. SQM 687.00 35.00 722.00 156.05 0.97 1.03 156.39 112914.84

Melamine Polish:- Polishing in high gloss/matt finish melamine clear polish on wood work in required

13.116 3.5 color wooden shade texture with following process in the sequence as detailed below: SQM 50.00 50.00 1360.45 0.97 1.03 1363.43 68171.47

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd

coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove

excess sealer layer and make the surface further smooth after this wet rubbing, then surface is

applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to

be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and

melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry

surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine

polish is applied with compressor pressure spray gun using melamine clear polish and melamine

thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to

be done in 1 or 2 layers without gap of time.)

Epoxy Paint :-Finishing with Epoxy paint two or more coats at all locations prepared and applied as

13.52 3.6 per manufacturers specifications including appropriate priming coat preparation of surface etc

4 Flooring Works :-

4.1 Laminated Wooden Flooring :-

Providing and Fixing AC-5 12mm thick made ofhighly anti-abrasive protective overlay laid over

superior water-resistant Highly Density Hard Wood interlocking system Fiber Board with wax coating

base laid over base layer of melamine impregnated film for dimenstional stability with underlay of 2

NS a MM polyurethene foam and 200 micron polythene sheet,on top over a smooth, flat, hard floor free SQM 89.00 89.00 2832.54 252096.11

from moisture, grease etc. with levelling of floor by rectifying the undulations if any and cleaning

complete as per drawing, manufacturer instruction and as directed by engineer incharge.

Skirting :- Extra for Providing and fixing Wooden skirting/profile of laminated HDF wood Plank

install with nails/adhesive over a smooth, flat, vertical surface free from moisture, grease etc.

complete as per drawing, manufacturer instruction and as directed by engineer incharge.

i Wooden Skirting 100 mm high, 12mm thick Rmt 35.00 35.00 516.98 18094.27

4.2 Vitrified Tile

Flooring:- Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by

the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved

brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4

coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily.

i Vitrified floor Tiles of size 600 x 600 mm (Glazed/Antiskid) SQM 58.00 58.00 1502.00 0.97 1.03 1505.29 87306.78

ii Vitrified floor Tiles of size 600 x 1200 mm (Glazed/Antiskid) SQM 14.00 14.00 1798.80 0.97 1.03 1802.74 25238.35

4.3 Heat Resistant Terrace Tiles

Digitally signed by SANGRAM

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

Terrace Tile :- Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with

SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and

sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4

12.55 a coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, SQM 82.00 82.00 1703.95 0.97 1.03 1707.68 140029.90

including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto

150 mm height along the parapet walls in the same manner.

Skirting :- Providing and fixing 100 mm high Heat resistant terrace Tile skirting laid on 12 mm

NS b (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry SQM 8.00 8.00 1379.45 11035.60

mixed with pigment to match the shade complete.

11.52 4.4 Italian Marble Flooring

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick

stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

a and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry

admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

i 18 mm thick Italian Marble stone slab SQM 169.00 169.00 6927.35 0.97 1.03 6942.52 1173286.03

ii Extra for Inlay Pattern (Mother of Pearl) SQM 3.00 3.00 39382.52 118147.55

NS "Based Extra for Nosing :- Extra for nosing in treads of steps

NS "Based Extra for stone in stair riser & treads using single length upto 2 meter

4.5 Granite Flooring:-

Providing and laying Granite stone flooring in required design and patterns, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge :

Coping:- Providing and laying stone coping in required design, in linear as well as curvilinear

portions of the building all complete as per the architectural drawings with specified thickness of

stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

NS a 30 mm thick Granite Stone SQM 12.00 12.00 4150.74 49808.90

b 18 mm thick Granite stone SQM 10.00 10.00 3036.94 30369.41

c 40 mm thick SandStone SQM 20.00 20.00 2522.88 50457.58

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and similar locations of required size,

approved shade, colour and texture by adhesive of approved make, joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of

edges to give high gloss finish etc. complete at all levels. Rate shall also inclusive of making required

openings/holes, moulding, rubbing, polishing etc complete as per drawing and as directed by EIC.

Note :- Plan area shall be measured, with all lead and lift and as directed by Project Consultant/

Engineer in charge.

a Quartz stone slab 18 mm thick SQM 7.00 7.00 11384.00 79688.00

b Italian marble slab 18 mm thick SQM 4.00 4.00 9178.00 36712.00

Extra for fixing marble /granite/ quartz stone, over and above corresponding basic item, in facia and

8.4 4.8 drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. Metre 33.00 2.00 35.00 568.55 0.97 1.03 569.80 19942.83

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform,

vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar

taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

IPS Flooring :- Providing and Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

11.3 4.10 stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding Digitally signed by SANGRAM

the cost of nosing of steps etc. complete. SINGH

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

i 40 mm thick with 20 mm nominal size stone aggregate SQM 89.00 89.00 614.20 0.97 1.03 615.55 54783.51

4.11 Granite Cobble stone :-

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for

paving in floors, drains etc. laid over 20 mm thick base mortar 1:4 (1 cement : 4 coarse sand) with

16.92 joints 10 mm wide filled with same mortar including ruled pointing etc. complete as per direction of SQM 107.00 107.00 2189.15 0.97 1.03 2193.94 234752.03

engineer-in-charge

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement

11.26 A slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete

with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

i 20-25 mm Thick

a 800X800 Shotblasted Kota Stone (25 mm thk) Flooring (Green & Yellow Colour) SQM 64.00 64.00 1948.25 0.97 1.03 1952.52 124961.07

4.12 CRAZY PATTERN STONE FLOORING

Crazy marble stone flooring, including filling the gaps with light shade pigment with white cement

marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of

4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1 mm

to 4 mm nominal size by volume), with under layer 25 mm thick cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and

cement slurry etc. complete :

11.15 18 mm thick crazy marble stone white, black or as specified SQM 4.00 4.00 1714.80 0.97 1.03 1718.56 6874.22

5 Cladding / Panelling Works

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer),

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,

including grouting of joints (Payment for grouting of joints to be made separately).

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer

work) including dado, skirting, risers of steps etc., in required design and pattern (if required with

marble stone slab pieces of different shapes, sizes & texture but of even thickness) on 12 mm

8.11 5.2 (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement

slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching

shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as

directed by the Engineer-in-Charge.

i 18 mm thick Italian Marble stone slab SQM 121.00 121.00 10414.80 0.97 1.03 10437.61 1262950.62

Dry Stone Cladding :- Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang

saw cut stone with machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel

frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather

sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work,

stainless steel cramps and pins etc. shall be paid for separately).

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with

machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the

required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The

frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which

shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement

:2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including

cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC

8.21 5.4 surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame KG 164.00 320.00 484.00 269.95 0.97 1.03 270.54 130941.94

work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved

by Engineer in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be

submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work

shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be

measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing

extra shall be paid).

Digitally signed by SANGRAM

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size,

adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry

8.22 5.5 stone cladding fixed on frame work at suitable location, including making necessary recesses in EACH 164.00 320.00 484.00 437.00 0.97 1.03 437.96 211971.20

stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Ceramic Tile flooring & wall cladding :- Providing and laying rectified Glazed Ceramic wall tiles in

different sizes (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622,

NS 5.6 of approved make, laid with cement based high polymer modified quick set tile adhesive (water

based) conforming to IS: 15477, in average 6 mm thickness including grouting the joints with white

cement and matching pigments etc., complete.

WALLPAPER PANELLING: Providing and fixing of fabric backed Wallpaper over existing walls/ Gypsum/

MDF/Plywood surface with approved adhesive, as per manufacturer's specification & as shown in drawing, of

NS 5.7 specified size & shade, including cutting, wastage, Provision for MEP (as required), all complete as per drawing, Sqm 10.00 10.00 3430.73 34307.33

designs and directions of Project manager. Rates shall include base preparation with 2 coat oil based primer, all

lead and lifts etc complete.

Providing and Panelling with specified plywood/ board by suitable screws of approved make in GI

framework. The work includes provision for opening if any required for MEP services etc, all complete

in all respect as per drawing, designs and directions of EIC (frame work shall be inclusive).

NS-38 i HDHMR Board 12 mm thick SQM 10.00 10.00 2284.04 22840.44

Veneer Panelling :- Providing and fixing plywood 3.5 to 4 mm thick, one side decorative veneer

8.28 5.9 conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming

coat on unexposed surface with :

Decorative veneer facings of approved manufacture Sqm 25.00 25.00 1946.25 0.97 1.03 1950.51 48762.81

Panelling :- Providing and paneling with the specified material for plain lining / cladding with

necessary screws, etc complete as per drawing and as directed by EIC.

i 1 mm thick Laminate Sqm 5.00 5.00 2650.52 13252.58

6.1 Flush Door

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type,

core of block board construction with frame of 1st class hard wood and well matched teak 3 ply

veneering with vertical grains or cross bands and face veneers on both faces of shutters.

i 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 5.00 5.00 3473.85 0.97 1.03 3481.46 17407.29

ii 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 30.00 30.00 3167.95 0.97 1.03 3174.89 95246.63

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type,

b core of block board construction with frame of 1st class hard wood and 1 mm thick laminate pasted

on both faces of shutters.

NS i 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 4.00 4.00 5051.01 - 20204.05

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of

flush door shutters (over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs

and priming coat on unexposed surface etc. complete :

9.40.1 i 2nd class teak wood

e Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold

fast lugs or dash fastener shall be paid for separately).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,

nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement :

3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Door Hardwares:- Providing and fixing of door hardwares in approved shade and make as per

drawing and as directed by EIC.

Digitally signed by SANGRAM

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

Main Door hardwares :Main Door hardwares :- Providing and fixing approved brand and

NS-45 i manufacture SS 304 Handle D-type (450 mm) fixed including SS screws etc. complete in all respects Pair 2.00 2.00 5747.18 11494.35

as per manufacturers' specifications & as directed by Engineer-in-charge.

Main Door hardwares :-Providing and fixing bright finished brass 100mm mortice latch and lock with

6 levers of approved quality and necessary screws etc. complete for 40 mm thick door with SS screws

etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-

Bedroom/Study / Servent room etc Door Hardwares :-Providing and fixing bedroom lock with one

side key other side knob with pair of handles as per approved model. for 35 mm thick door with SS

screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-

Living Area Toilet door hardwares :-Providing and fixing bathroom lock without key, with pair of ss

NS-48 iv brush finished knobs etc as per approved model. complete in all respects as per manufacturers' Set 9.00 9.00 2807.88 25270.92

specifications & as directed by Engineer-in-charge.

Providing and fixing SS 304 tower bolts barrel type, with necessary screws etc complete in all

NS-49 v respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing SS 304 hanging type door stopper with necessary screws etc. complete.

7 Glazing Work

7.01 3 Track UPVC Door (Bedrooms/Balcony)

Providing and fixing factory made UPVC white colour Factory made sliding glazed doors comprising

of multi chambered frame with inbuilt roller track and sash extruded profiles duly reinforced with 1.6

mm thick galvanised MS section shape, size length as per uPVC profile, wool pile, uPVC extruded

glazing beads, EPDM gasket , zinc alloy powder coated handles with key on one side of extreme

panels along with zinc plated MS multi point locking having transmission gear with keeps, zinc alloy

crescent lock powder coated, SS 304 grade body with adjustable double nylon rollers of bearing

capacity not less than 120 kg, GI fasteners, 100x8mm minimum, SS screws, mitred frame joints,

fasteners, fusion welding , drain holes, weather proof silicon sealant with or without backer rod,

minimum 10mm toughened glass Three Track, Three Panel sliding door with fly proof SS 304 grade

wire mesh of frame minimum 116x45mm & sash 46x82mm both having wall thickness 2.3mm.

b UPVC Window (Kitchen/Staircase/Toilet/Bathroom)

Factory-made white UPVC window system comprising a combination of fixed and three-track sliding

windows. The three-track, three-panel sliding window includes a fly-proof SS 304 grade wire mesh,

with a multi-chambered frame featuring an inbuilt roller track, sash, and mullion. The sliding panels

are fitted with a minimum of 6mm toughened glass for durability and safety. The fixed UPVC window

section is also provided with 6mm thick toughened glass, all as per the approved drawing

NS UPVC WINDOWS & Ventilator -

NS xii W12 (900 x 2250) Nos 2.00 2.00 signed by SANGRAM

Digitally 11080.24 22160.47

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

C Slide and Fold UPVC Doors

7.02 Glazed Door

A Frameless Door :-

Design,Providing, installation and fixing of single/double leaf 12 mm thick Toughened Glass Door

with all required arrangement & proper machine edge finish. Glass panels to be formed as per

approved modules 12 mm thick clear toughened glass edge polished and accurate designed holes to

NS-86 be installed by means of steel fittings Including top & bottom pivot, hydraulic Floor spring Lock SQM 2.88 2.88 12540.72 36117.26

approved make,SS Door Handle both side, all works including labour, door fittings/hardwares,

wastages, cost of scaffolding, finishing with frosted design film etc. complete as per drawing and as

directed by EIC.

7.03 Railing :-

Aluminium glazed Railing :- Design, Supply, Fabrication and installation of Glass Railing

Systems(H-1200mm) as per approved design complete using powder coated Aluminium top handrail

50 mm Dia or rectangular with one side minimum 50 mm, anchor bracket Aluminium 'U' channel/

mechanism including Cover profile & silicon grip with all necessary hardware along with 13.52 mm

thick laminated glass made of 6mm Clear Toughenned+1.52mmPVB+6mm thick clear toughened

Glass as per specifications, all fixing arrangements, fixing all accessories as per Manufacturer's

specifications and instructions of Engineer-in-Charge. Aluminium extruded sections shall not weigh

less than 4.5 kg/Rmt, EPDM gasket Rubber for packing on sides. Expandable Fasteners, adhesive

Staircase Railing :- Design, Supply, Fabrication and installation of Glass Railing Systems(H-

1200mm) as per approved design complete using melamine polished wooden handrail, PVD coated

SS Sections, 12 mm thick toughened glass, fixing mechanism, all necessary hardware, Expandable

Fasteners, adhesive etc. complete as per specifications, all fixing arrangements, fixing all

accessories as per Manufacturer's specifications and instructions of Engineer-in-Charge. .

Supply & Fixing of Curtain Wall Glazing System, using extruded built-up Aluminium profile i.e. –

KP 00107 (Mullion) 50MM X 171MM, Transon 50 x 100mm, KP00109(Pressure), KP00110(Cover

Plate) of grade 63400 WP IS : 733 and IS : 1285 anodised transparent or dyed to required shade

according to IS : 1868, (Minimum anodic coating of grade AC-15) / Pure Polyester powder coated

50-60 Microns in approved shade. The curtain wall glazing system have aluminium frame with

pressure plate and cover plate with screws and EPDM gasket of manufacturer to make glazing air /

water tight as per drawings and specifications. All the aluminium profiles shall be provided with

masking tape for safety against external scratches etc complete as per drawing and as directed by

Glazing with 24mm Thk DGU [6mm Low-E Toughened +12mm Air Gap+ 6mm Clear Toughened

8 Miscellaneous Works:-

GRC Screen -Providing and fixing glass reinforcement concrete customized Jali (GRC) screen/

moulding/ cornice as per approved pattern , design, colour of desired size etc. of approved make.

The cornice should be made from 53 grade white portland cement manufactured by separated ISI

company. Quantity, fine silica, sand, alkali resistant glass fiber manufactured by saintgobain or

equivalent, super plasticizer and polymers manufactured by BASF or equivalent and UV resistant &

synthetic inorganic pigments should be used for pigmentation manufactured by Bayberries (Germany)

or equivalent. The material casting should take place synthetic rubber /FRP mould manufacture by

Reckli or equivalent. The fixing of screen/cornice/moulding should be dry fixing is to be done by S.S.

Steel (SS-304 grade) L-shaped clamps, dash fasteners and pins/cement mortar or any suitable

means etc. complete as per site requirements and as per direction of Engineer-in-charge & as per

architectural drawing complete.

Screen/ jali of thickness 50mm with internal members thickness ranging between 25- 30mm, having

atleast 40-50% void space as per patern/ design of arch. (MS Frame if required shall be paid SQM 30.00 30.00 5530.25 - 165907.50

Digitally signed by SANGRAM

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

HPL Cladding :- Providing & Fixing of 06 mm thick High pressure Exterior Grade laminate. These are EN 438-

Part 6 complying, panels, which are manufactured by high pressure and temperature in a hot press. The core of

the panel consists of desired numbers of imported, long fibre virgin kraft papers, impregnated with specially

formulated double hardened Phenolic resin and another top layer of imported virgin Blue wool scale passed,

decorative paper layer impregnated with Melamine resin. The panels are flame retardant type class 1 as per BS:

476 Part 7, ASTM E84 and EN 438- Part 6. Poly-methyl methacrylate UV protecting films are provided at the top

of the Deco layer for optimum UV protection (passes 1500 hours). HPL panels have a tested Flexural Modulus of

≥11,000 MPa and Flexural strength of ≥100 MPa which makes the product enormously sturdy from inside. This

NS 8.02 product shows no distortion in extreme climatic changes such as from -20° C to +80 ° C or from dry climate to a SQM 34.00 34.00 7606.66 258626.56

relative humidity in excess of 85% – 90%. HPL panels are equipped with a maximum possible weather

resistance at extreme oceanic climates as it has duly passed the salt spray test conducted for 500 hours. HPL

panels pass a 3000 hours artificial weathering and are rated with a 5 for Grey scale rating & 7/8 for Blue wool

rating. HPL Density is 1.45gm/cm3 & Warranty of 10 years.The cladding system will be installed on aluminium

box section 38 x 38 x 2.5 mm with aluminium POP rivets are being used for fastening purpose (with appropriate

sliding and fixed hole

Steel work welded in built up sections/framed work, including cutting. Hoisting, fixing in position and

8.03 applying a priming coat of approved steel primer using structural steel etc. as required.

NS i In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works KG 2597.00 2727.00 5324.00 172.60 0.97 1.03 172.98 920934.84

8.04 Modular Kitchen :-

Supply and installation of Factory made modular kitchen, made out of 18mm HDHMR Board, pre

laminated inside(all unexposed surfaces) with balancing laminate of 0.8 mm thick, edge binding tape

with hot melt glue, outside with 1mm high glossed laminate of approved design, Before starting the

fabrication works in the factory contractor has to take all the physical measurements In modular

kitchen SS-304 grade baskets, SS handles, soft closing channels for drawer units, Crouser, Tall unit,

space for RO, Microwave, Chimney, Sink, below CP, dish rack 900 mm, cutlery tray 900 mm, blind

corner hinges, heavy black PVC Legs and overhead storage cabinets, ,. with some open shelves,

corner units, trays of ABS plastic for small articles, fasteners etc of approved brands/ Manufacturers

as per Drawings ( front) all complete as per approved shop drawing

i Type 1 (both side of kitchen) Ground floor Set 1.00 1.00 1098621.50 - 1098621.50

8.05 Modular Wardrobe :-

Factory made modular cup boards, made out of 12mm HDHMR board, laminated inside (all

unexposed surfaces) with balancing laminate of 0.8 mm thick, outside with 1mm laminate of approved

design and or Acrylic sheet etc as per approved design pattern, model of approved manufacturers/

NS i brands, having shutters, locks, SS hinges, self & soft closing channels for drawer units in the cup Sqm 24.00 24.00 32456.19 - 778948.66

boards. Area average 8sqm/room (minimum) including low height storage cabinets and overhead

storage cabinets. (Front elevation shall be measured for payment.)

8.06 Modular Washroom Vanity :-

Supply and installation of Factory-made modular vanity, made out of 12mm HDHMR Board and

Italian Marble countertop, laminated inside(all unexposed surfaces) with balancing laminate of 0.8

NS mm thick, outside with 1mm laminate as per approved design pattern, model of approved Sqm 8.00 8.00 28030.35 - 224242.80

manufacturers/ brands, having shutters, locks, SS hinges, self & soft closing channels for drawer

units. (Front elevation shall be measured for payment.)

Note :- CounterTop stone shall be paid seperately as per relevent item.

TV Cabinet :- Providing and fixing TV consol made of 12mm thick HDHMR board and or 12mm thick

water-resistant plywood, laminated with approved laminate 1mm thick on all surfaces, having drawers

with soft closing Channels of appropriate length, shutters with shelves, locks minimum two lever SS

NS 8.07 body of approved make, knobs/handles of SS304 grade. Overall (size 2250x450mm) minimum as per Sqm 6.00 6.00 28030.35 168182.10

approved design. The drawers shall be projecting 300mm from the face of the console. (Front

elevation shall be measured for payment.)

Digitally signed by SANGRAM

DSR (2023) Building Landscape Cost DSR Rate

S.No. Description Unit Total Qty DSR Rate Cess factor NDSR RATE DSR AMOUNT NS AMOUNT

No. Qty Qty Index (incl factors)

Supply & Installation of Glass Partition System/window using high-quality 12 mm thick tempered

glass panels of thickness as per approved shop drawings. The partition system shall be fixed with

anodized/powder-coated aluminum fittings, including floor mounted channels, patch fittings, and

corner connectors. All aluminum fittings shall be as per IS:733 and IS:1285 with anodic coating of

grade AC-15 (minimum) or powder-coated with 50-60 microns in approved shade. Necessary silicone

sealants shall be applied to ensure an air tight and water-resistant finish between the glass panels.All

glass panels must be free from scratches or defects, and masking tape or protective film must be

applied on-site to prevent damage during installation.The system shall comply with relevant codes

and standards for structural safety and glass installation.

Powder coated aluminium (minimum thickness of powder coating 50 micron) Sqm 8.00 8.00 4865.52 38924.19

Providing and fixing panelling on wall & ceilings with WPC (WoodPolymerComposite) panels 15 mm

thick of approved make & shade in approved pattern as directed by the architect. Rates shall be

inclusive of all hardware fitting, SS fixtures as required to fix the same on the wall and ceilings

including corner beading and fastners.

WPC Panel 15 mm thick Sqm 15.00 15.00 2650.52 39757.74

8.10 Palmet :- Providing and fixing 150 mm wide pelmet of 18 mm thick MR grade commercial plywood ISI Rmt 47.00

NS marked, including top cover of 18 mm commercial all complete with screw, rawl plug etc complete as 47.00 710.55 33395.84

per drawing and as directed by EIC.

8.11 Curtain :- Supply and fixing of curtain as approved.

NS i Sheer Curtain Sqm 42.30 42.30 949.82 40177.23

NS ii Thick silk curtain for blackout Sqm 98.70 98.70 3519.58 347383.01

Curtain Track :- supply and fixing of powdercoated aluminiumk curtain track with accesseries. Rate

shall include all required hardwares, screws etc complete.

i Curtain track Aluminium Powder coated Rmt 55.00 55.00 356.35 19599.15

iv Wall Bracket Pcs 80.00 80.00 219.29 17543.30

v Ceiling Bracket Pcs 10.00 10.00 82.23 822.34

Thermal Insulation :- Providing fixing thermal insulation of ceiling (under deck insulation) with Resin

Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G

12.34 8.13 Virgin Polythene bags,fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of Sqm 116.00 116.00 703.05 0.97 1.03 704.59 81732.40

12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Floor Protection :- Supply and installation of 4mm thick polypropylene (PP) sheets on the flooring to

NS 8.14 prevent damage during construction activities. The sheets shall be securely laid and fixed as per site Sqm 424.00 85.00 509.00 119.28 60714.00

Veneer Panelling :- Providing and fixing plywood 3.5 to 4 mm thick, one side decorative veneer

8.28 8.15 conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming

coat on unexposed surface with :

i Decorative veneer facings of approved manufacture Sqm 25.00 25.00 1946.25 0.97 1.03 1950.51 48762.81

9 Horticulture Works

Supplying and filling with sweet earth including royalty and carriage (sweet earth measured in stacks

Hort-2.2 9.1 will be deducted by 20% for payment) for mounds specified level mention in drawing and other areas Cum 2.00 2.00 515.60 0.97 1.03 516.73 1033.46

as per site condition.

PLANTATION :- Supply and Planting best quality container- grown healthy trees, Plants, ground cover etc of

NS 9.2 speciesand height as specified. All plants to be approved before planting. Rate shall include pit preparation,

excavation,planting etc complete.

i Alstonia Scolaris ( 7-8 ft Height) Nos 7.00 7.00 1173.69 8215.85

ii Delonix Ragia (8-10 ft Height) Nos 7.00 7.00 1173.69 8215.85

iii Bismarckia nobilis (6 ft height) Nos 2.00 2.00 2142.69 4285.37

iv Phoenix sylvestris ( 8 ft stem height) Nos 11.00 11.00 13978.24 153760.67

v Duranta spp ( 245 mm height) Nos 150.00 150.00 218.84 32826.56

Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing

ground prepared with proper level and ramming with required tools wooden and than rolling the

Hort. 2.34 9.3 surface with light roller make the surface smoothen and light watering the same maintenance for 30

days or more till the grass establish properly,as per direction of officer in charge.

Digitally signed by SANGRAM

Grand Total (All works) SINGH ₹ 76,63,301.73 ₹ 81,93,039.94

Grand Total (All works) SINGH ₹ 76,63,301.73 ₹ 81,93,039.94

S.NO. DESCRIPTION UNIT QTY AMOUNT IMAGE

All furnitures are indicative/reference only and subjected to approval from

client/architect.

Manufacturing, providing and placing in position machine made factory

1.01 assembled Add. Cabin Table of following dimensions with the following

specifications.

Supplying and placing in position Main table of the following specifications. The

Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height.

Top surface of the table shall made up of MDF (Medium density fibre ) board

duly finished with Veneer and final coating of PU. The Main desk should contain

in built key board pull out tray for keeping keyboard of computer. The front

modesty panel of the table shall be made up of MDF board of size 1640 mm x

600 mm x 16mm which shall also be duly finished with Veener and PU coating.

For personal storage one mobile pedestal (3 drawer unit) shall be provided of

size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal

shall also be made up of MDF duly finished with veener & final coating of PU.

The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height.

The side unit shall be made up of MDF board duly finshed with Veneer and final

finish by PU Coating. The design of the side unit shall be such that it can be

placed on either side of the main table. The side unit shall contain open space Each 1.00 122581.04 122581.04

for keeping cpu in extreme right side, one closed storage shutter at extreme left

end & open space in the middle with one shelf for keeping files. The thickness

of the top of the side unit shall be 25mm. The Size of the Back unit shall be

2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made

up of MDF board duly finished with veneer & final finish by PU coating. Below

storage shall be provided with wooden shutters & the upper left & right side of

the back unit shall also be provided with wooden shutters. The middle 3 door

shutters should be of glass of minimum 5mm thick for display purpose. The

hardness of the PU coating shall be 1.5H

Manufacturing, providing and placing in position high back Chair

Revolving type Reef High Back, (as per the sample approved).

Digitally signed by SANGRAM

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded

glass filled poly-amide.Upholstered seat sub- assembly consists of moulded

High Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness

load 16 ± 2 kgf as per IS:7888 for 25% compression. Seat SIZE: 45.5cm. (D) x

BACK ASSEMBLY: The Cushioned back is made of PU Foam with

Polypropylene Injection molded Plastic Inner. ARMRESTS: The armrest having

four range of adjustment. Armrest top is made up of high density PU molded

over glass filled Poly-amide inner.

Height adjustment

sub assembly is inserted in the Aluminum Die Cast Arm body & all other

adjustment are provided in adjustable arm top sub assembly. · Up-Down

adjustment has 8 position (10.5±0.5cm range) · Arm top swivel adjustment- 2

position, 12°±2° swivel inside. Arm top width adjustment - Any position

(2.0±0.5cm range each arm top) · Arm top To - Fro Adjustment- any position

(4.0±0.5cm range) ·

Back Track MECHANISM: The

adjustable tilting mechanism is designed with the following features: · 360°

revolving type. · Forward tilt of sesat and back. · Upright tilt lock. · Tilt tension

adjustment can be operated in seating position. · 3-position Tilt limiter. SEAT

DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and

integrated with the mechanism with help of Polypropene Seat cover. Seat

Depth can be adjusted in sitting position. Seat depth adjustment range is of

ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height

can be adjusted in sitting position. It can be adjusted in the range of 7.5±0.5

Manufacturing, providing and placing in position mid back Chair

Revolving type & Reef High Back, (as per the sample finally approved)

Supplying and placing mesh chair with SEAT/BACK ASSEMBLY: The seat is

made up of 1.5 ±0.1cm. thick hot-pressed

plywood and upholstered with fabric upholstery covers and moulded

Polyurethane foam. The seat has extra thick foam on front edge to give comfort

to popliteal area. The Back is injection moulded in glass filled Polypropylene

which is upholstered with

Mesh fabric.The back consist of adjustable lumbar support made of injection

moulded Polypropylene having an adjustment of 5.0 ±0.1 cm.HIGH

RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam

is moulded with density 45+2 kg/m and hardness 162 kg for 25% compression.

3. ARMRESTS :The adjustable armrest is designed with the following features :

Visitor Chair • Up-Down adjustment- 6 steps (7.2 $ 0.5cm range) Each 2.00 13617.98 27235.97

• Armrest top is mounted on Armrest structure made of glass filled Nylon

• Armrest Top is PU moulded over glass filled Nylon insert.

4. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK: The

mechanism is designed with the following features: 360° revolving type.3

position locking with anti shock mechanism.Tilt tension adjustment. Company

should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard

certified. Product should be Greenguard (UL) and BIFMA LEVEL 2 Certified.

Digitally signed by SANGRAM

2 Drawing Area

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure

Leather Upholstery - Pigmented Durable and ergonomically perfect for seating.

The top grains of leather is clearly visible which adds to the aesthetics

S Spring Webbing- Provides bouncing back action for floating

feeling.Construction- Made of solid wood frame with ply cross section which is

2.01 Sofa moisture , termite and borer resistant. Adequate treatment of wood initiated to

enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply ,

Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat

is made of soft foam of density 28 kg/m3 which enhances comfort and

cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa

is elevated to allow a level of ground clearance.

Dimension :-size 1820mm (W)x 840mm (D)x760(H)

Dimension :-size 1060mm (W)x 840mm (D)x760(H)

Providing and placing in position Centre Table having a size of : 1000mm(L) x

600mm(D) x 425mm(H). Understructure of the table which includes Legs, top

wooden frame & bottom tie members are made out of first quality rubberwood

of approved make without knots &defects on all faces. Bottom tray is made of

1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top:

8mm thick toughened glass of approved make. Construction: Knock-down

2.02 assembly.Wooden members are PU painted with hardness-2H. Metal Each 2.00 31136.61 62273.22

components are powder coated. Bottom MS metal tray is having floral pattern

laser-cut. Top glass is having sand blasted floral pattern on bottom surface 5.

Hardware: Knock-down assembly with high quality standard hardware like

screws, metal inserts, wooden dowel, plastic leg bush. Complete all as per the

dimension of Engineer-in-charge.Complete all as per the direction of Engineer

Providing and placing in position Corner Table having a size of : 500mm(L) x

500mm(D) x 425mm(H). Understructure of the table which includes Legs, top

wooden frame & bottom tie members are made out of first quality rubberwood

of approved make without knots &defects on all faces. Bottom tray is made of

1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top:

8mm thick toughened glass of approved make. Construction: Knock-down

assembly.Wooden members are PU painted with hardness-2H. Metal

components are powder coated. Bottom MS metal tray is having floral pattern

laser-cut. Top glass is having sand blasted floral pattern on bottom surface 5.

Hardware: Knock-down assembly with high quality standard hardware like

screws, metal inserts, wooden dowel, plastic leg bush. Complete all as per the

dimension of Engineer-in-charge. Complete all as per the direction of Engineer

Digitally signed by SANGRAM

3.01 Bed King Dim-1922 x 2304 x 1030 mm (W X D X H).Bed Structure-Matt-Black powder

coated Metal Frames of 25 mm square MS pipes (1.2 mm thick) and MS Channels (1

mm thick) Foot-Board and Side Panels-Made of 2 parts. (A) Lower part in 18 mm PLT

while (B) upper part is High-Gloss PU painted 18 mm MDFHeadboard (Cushioned

Panels – Caprinova 2 tone Brown)- Side Panels of the Headboard part is High-Gloss PU

painted 18 mm MDF while the rest is made in 18 mm PLTHeadboard front has two Set 4.00 133405.80 533623.21

openable upholstered cushioned panels covering storage area. Middle panel of

headboard is also openable upholstered cushioned panel and can be used as coffee

tableMattress Panel-18 mm thick PLT boardHinges, KD Fittings-Hettich (Germany)

3.02 Side Table Material & SubtypeEngineered Wood - Particle Board, Engineered Wood -

Table Top MaterialEngineered Wood

Frame MaterialEngineered Wood

Colour & Colour FamilyBrown - Dark Oak, White - Frosty White

Dimension(W)525mm X (D)385mm X (H)450mm

Table Top Thickness18 mm

Assembly TypeKnock Down

Storage TypeDrawers

Warranty5 Years

3.03 Bench Supplying and placing Bench with overall size of 1500x600x500mm. Made with

solid wood with a very fine Walnut finish bench are upholstered in fabric with a

light brown hue, giving it a cosy and friendly appearance.

Dining Table + Chair (6 Nos)

Material & SubtypeFabric - Polyester, Solid Wood - Rubber Wood

Table Top MaterialSolid Wood

Table Leg MaterialSolid Wood

Chair Leg MaterialSolid Wood

Chair Frame MaterialSolid Wood

Frame MaterialSolid Wood

Upholstery MaterialFabric

4.01 Seat MaterialFabric Set 1.00 185758.70 185758.70

Leg MaterialSolid Wood

Colour & Colour FamilyBrown - Burnish Oak, Beige

Dimension Of Table(W)1600mmX (D)900mm X (H)760mm

Dimension Of Chair(W)530mm X (D)500mm X (H)980mm

Seating Capacity6 Seater

Seating Height460mm

Table Top Thickness19mm

5 FF Living Area

Digitally signed by SANGRAM

Seat is leatherette upholstered cushion fitted to a seat tray. The cushion is

made of 1.2 cm of PU slabstockfoam. Slabstock foam glued to CRCA sheet of

0.12 cm (+0.01cm) thick and upholstered with leatherette. The seat tray Is

made of CRCA steel of 0.25 cm thk (#0.01cm) as per IS:513

It is powder coated with epoxy based polyster powder coating (40-60 microns).

* SEAT CUSHION SIZE: 40.0 cm. (W) x 34.5 cm. (D)* TOP TRAY SIZE: 41.5

2. WOODEN UNDERSTRUCTURE: Understructure of bar stool is made of

5.01 Bar High Stool Each 2.00 27160.59 54321.17

FSC-certified seasoned teak wood finished with a clear matt coat of PU

lacquer. * UNDERSTRUCTURE SIZE: 48.6 cm (W) x 47.0 cm (D) x 6.88 cm

(H) 3. FOOT REST ASSEMBLY Foot rest is made up of 01.6 cm ($0.02 cm)

M.S. ERW tube (IS:71380). It is epoxy based powder coating (40-60 microns).

Additionally it is coated with abrasion resistance coating * FOOT REST SIZE:

Material & Subtype : Premium Leatherette, Metal - Stainless Steel

Frame MaterialSolid Wood

Upholstery MaterialPremium Leatherette

Seat MaterialPremium Leatherette

Leg MaterialMetal

Colour & Colour FamilyGrey - Oyster

5.02 Sofa Dimension(W)2930mm X (D)2340mm X (H)930mm Set 1.00 119135.06 119135.06

MechanismClick Clack Mechanism

Seating Capacity4 Seater

Seating Height440mm

FunctionAdjustable Headrest

StyleContemporary

Assembly TypeKnock Down

Warranty5 Years

Providing and placing in position Centre Table having a size of : 1000mm(L) x

600mm(D) x 425mm(H). Understructure of the table which includes Legs, top

wooden frame & bottom tie members are made out of first quality rubberwood

of approved make without knots &defects on all faces. Bottom tray is made of

1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top:

8mm thick toughened glass of approved make. Construction: Knock-down

5.03 assembly.Wooden members are PU painted with hardness-2H. Metal Each 1.00 31136.61 31136.61

components are powder coated. Bottom MS metal tray is having floral pattern

laser-cut. Top glass is having sand blasted floral pattern on bottom surface 5.

Hardware: Knock-down assembly with high quality standard hardware like

screws, metal inserts, wooden dowel, plastic leg bush. Complete all as per the

dimension of Engineer-in-charge.Complete all as per the direction of Engineer

Digitally signed by SANGRAM

Supplying and placing 3str sofa with overall size of 97x89x97.5cm. A trendy,

luxurious sofa with tufted bench seating that adds style to any interior.

Curvaceous contours in

Sofa (Single multiple colour options for single or dual-tone schemes. Comfortable full back

5.04 support and panel details in solid wood finish. Elevated on cylindrical legs that Set 1.00 44817.64 44817.64

facilitate easy floor cleaning, everyday.

Manufacturing, providing and placing in position mid back Chair

6.01 Revolving type & Crown High Back, (as per the sample finally approved

by the department).

Supplying and placing mesh chair with SEAT/BACK ASSEMBLY: The seat is

made up of 1.5 ±0.1cm. thick hot-pressed

plywood and upholstered with fabric upholstery covers and moulded

Polyurethane foam. The seat has extra thick foam on front edge to give comfort

to popliteal area. The Back is injection moulded in glass filled Polypropylene

which is upholstered with

Mesh fabric.The back consist of adjustable lumbar support made of injection

moulded Polypropylene having an adjustment of 5.0 ±0.1 cm.HIGH

RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam

is moulded with density 45+2 kg/m and hardness 162 kg for 25% compression.

3. ARMRESTS :The adjustable armrest is designed with the following features :

• Up-Down adjustment- 6 steps (7.2 $ 0.5cm range) Each 1.00 13617.98 13617.98

• Armrest top is mounted on Armrest structure made of glass filled Nylon

• Armrest Top is PU moulded over glass filled Nylon insert.

4. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK: The

mechanism is designed with the following features: 360° revolving type.3

position locking with anti shock mechanism.Tilt tension adjustment. Company

should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard

certified. Product should be Greenguard (UL) and BIFMA LEVEL 2 Certified.

Dimensions W x H x D (cm) :- 120 x 71.4 x 60.5

Primary Material : Particle Board

6.02 Desk with Shelves Each 1.00 24656.55 24656.55

Storage and Drawer

7 Outdoor Furniture

Digitally signed by SANGRAM

Dining Armchair with Cushion

Aluminium frame powder coated,

7.01 Woven with Synthetic Wicker. Set 4.00 20284.44 81137.74

( Dimensions : W55 x D64 x H83 Cm. )

Warranty5 Years

Dining Table + 4 Dining Chair

Dining Table-with Aluminium Frame Powder Coated. Table

Top in 8 mm toughened glass.

(Dimensions: W100 x D100 x H75 Cm)

Warranty5 Years

7.03 Guard Chair : Providing and placing at position Guard chair as approved.

Grand Total (furniture) 2118199.58 Rs

Grand Total (furniture) 2118199.58 Rs

Digitally signed by SANGRAM

Description Unit Quantity Rate Amount

Supplying, installation, testing and commissioning of Passenger Lift having serving

1.0 different floors in the lift shaft as per detailed specifications enclosed and as under:- -

(i) Controller: A.C. variable voltage and variable frequency. -

(ii) Operation : Microprocessor based full simplex collective control with and without

(iii) Power : 415 V ± 10%, 3 phase, 50 Hz,4 wire system. -

(iv) Auxilary power Supply :230 V ± 10%, 50 Hz single phase supply. -

(v) Type of doors

(a) Car : Glass door framed in Stainless Steel hairline finish

(b) Landing doors : Glass door framed in Stainless Steel hairline finish

(vi) Voice announcement system with music in the car to announce the position of the

elevator as the car stops at a floor served by the elevator. -

(vii) Automatic rescue device complete with dry maintenance free batteries as required.

(viii) Control panel in the car and hall button panel at each landing. -

(ix) Braille buttons inside the car and at all landings. -

(xi) Other specifications shall be as per NBC & Indian Stansdards. -

Suitable for 6 persons (630 Kgs)

Shaft Size in mm - 1500 x 1200 mm

Floors to be Served - G+2 Nos 1 1916474.88 1916474.88

For details refer Drawing.

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

SUMMARY OF ELECTRIAL WORK

S. NO. ITEM DESCRIPTION AMOUNT AMOUNT

A. ELECTRICAL AND LV SERVICES

I. POINT WIRING 745869.49 5390.00

II. LIGHT FITTING & FANS 141829.84 629108.35

III. DISTRIBUTION PANELS 116248.36 117663.43

IV. EARTHING 39443.18 0.00

V. CABLES, CABLE TRAY'S, RACE WAYS 263210.27 370750.00

VI. UPS / INVERTER 187780.00 0.00

VII. LIGHTING AUTOMATION 43413.71 651291.00

VIII. EXTERNAL LIGHTING 0.00 640369.00

IX. 20 KVA DG SET & ACCESSORIES 0.00 519103.00

X. SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM 325336.42 0.00

XI. CCTV SYSTEM 0.00 279764.16

XII. TV SYSTEM 18110.36 761.00

XIII. DATA, WIFI AND TELEPHONE SYSTEM 41917.57 427511.00

XIV AUTOMATED BOOM BARRIER SYSTEM 0.00 138702.00

TOTAL FOR ELECTRICAL WORK 1923159.20 3780412.95

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

ITEM DESCRIPTION QUANTITY UNIT DSR (incl

NO. DSR Correction Cess factor Cost Index NON DSR DSR NON DSR

I. POINT WIRING

1 1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface/ recessed steel conduit

with modular switch modular plate suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable etc.as required.

2 1.4 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed steel conduit, 2 way modular

switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC

insulated copper conductor single core cable etc as required. 8 Point 1981.00 1.06 0.97 1.03 2111.01 16888.08 0.00

3 1.5 Wiring for power plug points with 2 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor,

single core cable in surface/ recessed steel conduit along with 1 No. 4 sq.mm. FRLS

PVC insulated copper conductor single core cable for loop earthing as required.

4 1.6 Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS PVC

insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along

with 2 Nos. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for

loop earthing as required. 1 Point 662.00 1.06 0.97 1.03 705.45 705.45 0.00

5 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel

conduit as required

6 Supplying and drawing following sizes of FRLS PVC insulated copper conductor,

single core cable in the existing surface/ recessed steel/ PVC conduit as required.

7 1.25 Supplying and fixing two module stepped type electronic fan regulator on the

existing modular plate switch box including connections but excluding modular plate

8 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete

9 1.56 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket

outlet and 2 nos. 5/6 A modular switch, connections etc. as required.

Digitally signed by SANGRAM

10 NS1 Supplying & fixing SPN starter 25 amp along with 25 amp power socket for power

load complete with GI box and modular surface plate, connection accesseries etc as 1078.00 5390.00

required. (for geyser) 5 Nos. 0.00

11 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet

and 5/6 A modular switch, connections etc. as required. 24 Nos. 477.00 1.06 0.97 1.03 508.30 12199.32 0.00

12 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular

socket outlet and 15/16 A modular switch, connections etc. as required.

13 1.34 Supplying and fixing brass batten/ angle holder including connection etc. as

14 1.26 Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required. 10 Each 40.00 1.06 0.97 1.03 42.63 426.25 0.00

15 1.27 Supplying and fixing of following size/ modules, GI box alongwith modular base &

cover plate for modular switches in recess etc as required.

16 Civil-10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling

fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet

with its top surface hacked for proper bonding, top lid shall be screwed into the cast

iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard

17 Supplying and fixing of following sizes of steel conduit along with accessories in

surface/recess including painting in case of surface conduit, or cutting the wall and

making good the same in case of recessed conduit as required.

18 Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including cutting the wall and making good the same in

case of recessed conduit as required.

TOTAL SH-I CARRIED OVER TO SUMMARY 745869.49 5390.00

II. LIGHT FITTING & FANS

Digitally signed by SANGRAM

1 NS2 Supply, installastion, testing & commissioning of suitable for general lighting

recessed downlighter with 40mm height suitable for general lighting. Luminaire

should have die cast heat sink with polycarbonate diffuser. The luminaire should have

CRI > 80 and CCT of 4000K. The luminaire shall be compliant with IP20

classification.The fixture should have a minimum system efficacy of 110 lumen/Watt

and a minimum system lumen output of 2000 lumens and maximum system wattage

of 18 Watts. The luminaire shall be designed so as to ensure lumen depreciation of

up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic

driver used shall have a power factor >0.95 , THD <10%. The fixture should comply

with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 22 Nos. 2581.00 0.00 56782.00

ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1

ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and

IEC61547 ed.2.0, 2009, CISPR- 15 for EMI. Manufacturer shall have inhouse lab

approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports

need to be submitted from a NABL/UL accredited lab to verify above parameters.

Including 3 core 2.5 sq.mm FRLS PVC insulated and PVC sheathed copper

conductor cable and earthing etc. upto suitable point complete as required.

2 NS3 Supply, installastion, testing & commissioning of recessed type LED downlight with

maximum system wattage 40W and minimum system lumen 4000lm. CCT=4000K,

CRI>80. Housing made of pressure die cast Aluminium. Specialy design optics made

of aluminum reflector with beam angle 36 deg for auditorium purpose. The luminaire

shall have a rated system lifetime of 40,000 burning hours at L70. The luminaire shall

meet IP20 rating with THD<10% and PF > 0.9. Operating voltage 220-240V , 50/60 45 Nos. 6375.00 0.00 286875.00

Hz .Fixture should be available in DALI dimmable version or compitable with Dali

System.Including 3 core 1.5 sq.mm FRLS PVC insulated and PVC sheathed copper

conductor cable and earthing etc. Up to suitable point complete as required.

Dimensions:- H-142mm, D=193mm and ceiling cut out dia= 175mm.

3 NS-4 Supply, installastion, testing & commissioning of LED maximum system wattage 36W

Integral 4 ft waterproof IP65 luminaire with polycarbonate housing and PC Glossy

cover. The luminaire should have a color consistency SDCM < 5, CRI > 80 and CCT

of 6500K. Luminaire shall be designed to emit at least 4400 nominal lumens at a

system efficacy of atleast 120 lumen/watt. The luminaire shall be designed so as to

ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient

temp 45 deg C. The electronic driver used shall have a power factor >0.95 and THD

<10% and suitable for an operationg voltage range of 140-270V AC.The LED driver

should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 4 Nos. 7741.00 0.00 30964.00

in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1,

2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer

shall have inhouse lab approved by NABL or ministry of science of govt of India. LM

79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify

above parameters.Including 3 core 1.5 sq.mm FRLS PVC insulated and PVC

sheathed copper conductor cable and earthing etc. Up to suitable point complete as

4 NS-5 Supply, installastion, testing & commissioning of Surface LED batten IP20 2ft made

of Aluminum extrusion housing with high efficiency polycarbonate diffuser , LED Used

shall be SMD type and fixture should have minimum efficacy at System level (Not

Chip Level) >=100lumens/watt with Minimum system Lumens 1000 with maximum

input power of 10 Watt. Life of fixture (Including Driver) : 25000 burning Hrs. @

L70B50 , CRI >80, PF >0.9 & THD<30%, an operating Voltage Range of 160 - 240

VAC. the fixture design should comply with EMC / EMI compliance along with BIS

certification for LED Driver & Luminaire seperately. Including 3 core 1.5 sq.mm FRLS

PVC insulated and PVC sheathed copper conductor cable and earthing etc. Up to

suitable point complete as required.

Digitally signed by SANGRAM

5 NS-6 Supply, installastion, testing & commissioning of Wall bracket decorative light fixture

with 27W lamp with B22 base. Housing made of Metal, synthetics in white color

6 NS-7 Supply, installastion, testing & commissioning of LED BULB 10W 800lm E27 6500K

A67 ,colour temperature 5700 K having efficacy not less than 80 lm/W, CRI ≥ 70

,THD ≤ 10%, complete as required or approved Equivalent. 2 Nos. 387.00 0.00 774.00

7 NS-8 Supply, installastion, testing & commissioning of Chandelier light KCH-CHR-

MD160275216A or approved equivalent with minimum 6 Opal glass Chandelier with

Chrome finish LED lamps with min 4W x 6 suspensed from ceiling with full

suspension arrangement and complete as required. 1 Nos. 21163.00 0.00 21163.00

8 NS-9 Supply, installastion, testing & commissioning of LED Bulkhead with a nominal

system lumen output of 600 lumens and a minimum system efficacy of 60 lm/W. The

luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The

luminaire should have a color temperature of 6500K and CRI > 70. The luminaire

shall meet IP66 rating and IK 09 rating with THD < 20% and PF > 0.9. The luminaire

housing should made of High pressure die cast Aluminium with polycarbonate front

diffuser. The total power consumption should not exceed 10W (including driver).

Including 3 core 1.5 sq.mm FRLS PVC insulated and PVC sheathed copper

conductor cable and earthing etc. Up to suitable point complete as required.

9 NS-10 Supply, installastion, testing & commissioning of LED based Flood light, housing

made up of pressure die cast aluminum Alloy with effective thermal management,

sturdiness and embossed brand name/logo name of manufacturer and Anti Dust

Exposed Lens optics. The fixture should have a minimum system efficacy of 100

lumen/Watt and a minimum system lumen output of 7000 lumens and maximum

system wattage of 35 Watts.The fixture shall have a CRI of minimum 70. The fixture

shall be designed for a system life of 50,000 hours @70% lumen maintenance.

Ingress Protection of IP65 (lamp and gear Compartment) and Mechanical Impact

Resistance Rating of IK >=05.The fixture driver should have an operating voltage

range of 140-270 V, surge protection of >=3KV, PF >0.95 and THD<10%. The fixture

should comply with the parameters as per IS10322. The LED driver should comply to

IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with

IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for

performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI. LM 79 and LM80

reports need to be submitted from a NABL/UL accredited lab to verify above

10 NS-11 Supply, installastion, testing & commissioning of LED Flexible Striplight 4-5Watt/mtr,

4000-4250K, IP65 of approved color for indoor mounting with transformer/Driver unit

at every 5mtrs complete in all respects. 300 meter 95.00 0.00 28500.00

11 NS-12 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star

rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation:

B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope,

copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum

6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019),

THD less than 10%, remote or electronic regulator unit for speed control and all

remaining accessories including safety pin, nut bolts, washers, temperature rise=75

degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50

Hz, single phase AC Supply, earthing etc. complete as required.

Digitally signed by SANGRAM

12 NS-13 Supplying, installation, testing and commissioning of 900mm sweep BLDC ceiling

fan, 300mm down road, canopies, shackles, three number blade & suitable for

operation on 230 volts 50 Hz, single phase A.C. supply including wiring the down rod

of suitable with 1.5 sqmm. PVC insulated copper conductor single core FRLS cable,

earthing the regulator etc. & as per make & models in enclosed list of approved

makes as required & as per make & models in enclosed list of approved makes as

13 NS-14 Supplying, installation, testing and commissioning of 300mm exhaust fan suitable for

operation on 230 volts 50 Hz, single phase A.C. supply including wiring the down rod

of suitable with 1.5 sqmm. PVC insulated copper conductor single core FRLS cable,

earthing the regulator etc. & as per make & models in enclosed list of approved

makes as required & as per make & models in enclosed list of approved makes as

14 15.1 Supplying, installation, testing and commissioning of Passive Infrared(PIR)

technology based occupancy sensor having high preformance, non regulating

programmable type, suitable for connected load upto 10Amp , for mounting height up

to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing

arrangements i/c programming at site etc. complete as required. 7 Each 4602.00 1.06 0.97 1.03 4904.02 34328.16 0.00

15 15.2 Supplying, installation, testing and commissioning of Passive Infrared(PIR)

technology based occupancy sensor with day light dimming(lighting level shall be

regulated as per availability of natural day light in an area along with occupancy

detection.) having high preformance, regulating programmable type, suitable for

connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter

coverage area along with necessary fixing arrangements i/c programming at site etc.

TOTAL SH-II CARRIED OVER TO SUMMARY 141829.84 629108.35

III. DISTRIBUTION PANELS

1 2.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

2 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet

steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/Isolator)

3 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

4 Supplying and fixing following rating, double pole, 240 volts, MCB DP in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Digitally signed by SANGRAM

5 Supplying and fixing of following rating, four pole 415 volts, MCB TPN in the existing

MCB DB complete with connection,testing and commissioning etc. as required.

6 2.14 Supplying and fixing of following rating double pole (Single phase and neutral) 240

volts, residual current circuit breaker (RCCB), having a current sensivity current 30

miliampere in the existing MCB DB complete with connections, testing &

commissioning etc. as required.

7 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc.

8 NS-15 Lighting and Power Panel

CT Main Meter compartment as per NDMC requirement

2 No. 100 Amp FP Moulded Case Circuit Breaker. (TMR Type)

100 Amp ATS for DG & RAW power supply

1 Set of phase indicating lamps with MCB.

1 Set of ON/OFF indicating lamps with MCB.

1 No. Digital MFM with CT's.

150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

10 Nos. 63 Amp 4P Miniature Circuit Breaker.

4 Nos. 40 Amp DP Miniature Circuit Breaker.

10/16 Amp SPMCB- 10 nos

Panel described as above 1 Nos. 117663.43 0.00 117663.43

Digitally signed by SANGRAM

1 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,

and providing masonry enclosure with cover plate having locking arrangement and

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

2 5.7 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor

earth electrode, including connection/ termination with GI thimble etc. as required. 50 Meter 51.00 1.06 0.97 1.03 54.35 2717.35

3 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections

etc. as required. 0.00

TOTAL SH-IV CARRIED OVER TO SUMMARY 39443.18 0.00

V. CABLES, CABLE TRAY'S, RACE WAYS

(LT Cables and Terminations)

1 NS16 Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed

Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC

system, with inner and outer PVC sheath, outer sheath provided with FRLS

insulation, galvanised steel armouring (round or flat as mentioned) and with all

components as mentioned in BOQ, specifications and schedule, complete etc. as

1.2 4 core, 16 sq.mm. (Cu Ar. Cable) 40 Meter 1649.00 0.00 65960.00

1.3 4 core, 6 sq.mm. (Cu Ar. Cable) 30 Meter 734.00 0.00 22020.00

1.5 2 core, 10 sq.mm. (Cu Ar. Cable) 100 Meter 649.00 0.00 64900.00

1.6 2 core, 6 sq.mm. (Cu Ar. Cable) 80 Meter 429.00 0.00 34320.00

2 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size direct in ground including excavation, sand cushioning,

protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

4 7.8 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size on cable tray as required.

5 Supplying and making end termination with brass compression gland and aluminium

lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium

conductor cable of 1.1 kV grade as required.

Digitally signed by SANGRAM

6 Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete

with fitting and cutting, jointing etc..direct in ground (75 cm below ground level)

including excavation and refilling the trench but excluding sand cushioning and

protective covering etc., complete as required.

7 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable

tray (galvanisation thickness not less than 50 microns) with perforation not more than

17.5%, in convenient sections, joined with connectors, suspended from the ceiling

with G.I. suspenders including G.I. bolts & nuts, etc. as required.

12 INSPECTION CHAMBER:

Constructing brick masonry chamber for underground C.I. inspection

chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse

sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions,

total weight of cover with frame to be not less than 38 kg (weight of cover

23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1

cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size),

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone

aggregate 40 mm nominal size), inside plastering 12 mm thick with

cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete as

19.30 per standard design:

12.1 19.30.1 Inside dimensions 455x610 mm and 45 cm deep for single pipe line 0.00

12.1.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 8 Each 6937.00 1.06 0.97 1.03 7392.27 59138.13 0.00

TOTAL SH-V CARRIED OVER TO SUMMARY 263210.27 370750.00

VI. DSR 2024 UPS / INVERTER

Digitally signed by SANGRAM

Input supply: Three Phase, Output supply: Single Phase

Supplying, installation, Testing & Commissioning of ON LINE UPS

,Uninterruptible Power Supply (UPS) system suitable for parallel operation, to

power a load of approximately rated KVA non-linear load. The individual UPS

modules shall include a Rectifier, inverter, battery bank ( separate item) any

other peripherals required for paralleling the individual UPS system and Static

Bypass switch. any other peripherals required. Provision should be available for

manual bypass also. The UPS systems offered are to be of the latest

technology with Digital Control Microprocessor based, for reliable operation,

using IGBT's both in the rectifier & inverter. The quality of design,

manufacturing and inspection process should confirm to the relevant Inter-national

standards such as IEC/EN/VDE. The operating efficiency of the UPS systems

should be of the highest order while delivering quality power to the 100%

non-linear loads. the total harmonic effect ITHD on the input grid shall be

within 5% @ 50 %load. (The required LC filters shall be included in UPS cost).

extreme power factor kit to be include to limit the input pf to 0.99 and output power

Input supply: 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage:

1Phase 220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10

mins, Sine wave output.

Operating temperature ) 0 to 40 deg C., Relative humidity 0-95 non condensing,

noise level less than 60db at 1 meter distance, protections: Input Under voltage

over voltage, abnormal out voltage, battery over charging, output over current,

short ckt protection, battery deep discharge protection, surge rating 600J, Display

watt/VA,Amp and Voltage power parameters. UPS must comply with low voltage

electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and

Part 2, it shall be a VFI-type UPS (as per standard IEC 62040-3) . Both the UPS

should be with 3 Level IGBT Based Inverter Technology, Communication

RS232/RS485/SNMP port open protocol for BMS integration as per approved by

Engineering in charge (Required battery racks and interconnecting cables and

connectors are inclusive of the cost)

( Minimum 96% Energy efficiency)

1.2 7.5 Battery type AMF VRLA , ABS container, maintenance free,

TOTAL SH-VI CARRIED OVER TO SUMMARY 187780.00 0.00

VII. LIGHTING AUTOMATION

1.0 NS-19 Supply, Installation, testing & commissioning of 6 Channel DALI high frequency LED

ballasts controller. Each DALI outputs allowing it to control up to 60 DALI devices.

The DALI control signals can be programmed to operate automatically isolate the

power circuit when all associated DALI channels are at 0%. The device is DIN-rail

mountable integral DALI bus power supply, removing the need for an additional

external device, complete as required.

2.0 NS-20 Supply, Installation, testing & commissioning of 6 Channel Relay controller. 1 Each 50932.00 0.00 50932.00

3.0 NS-21 Supply, installation, testing and commissioning of Antumbra 6 Button keypad with

Proximate Feautre with IP 22 degree protection. 8 Each 29286.00 0.00 234288.00

4.0 NS-22 Supply, installation, testing and commissioning of Ceiling Mount 360 degree Multi

Sensor with PIR, LUX and IR Function inbuilt, having range of 7.5 x 5.4 meter at a

Digitally signed by SANGRAM

5.0 NS-23 Supply, Testing & Commissioning of Power Supply. 1 Each 24830.00 0.00 24830.00

6.0 NS-24 Supply of Automation Panel with Incoming protection Devices like FP MCB, DP

ELCB, FP Surge Arrestor and Outgoing MCB SP with Cable Alley, Netural/Earth Link

7.0 NS-25 Supply, installation, testing and commissioning of Antumbra with display screen

having 20 schens keypad with Proximate Feautre with IP 22 degree protection.

8 1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

recessed steel/ PVC conduit as required.

9 Supplying and drawing following sizes of FRLS PVC insulated copper conductor,

single core cable in the existing surface/ recessed steel/ PVC conduit as required.

10 Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including cutting the wall and making good the same in

case of recessed conduit as required.

TOTAL SH-VII CARRIED OVER TO SUMMARY 43413.71 651291.00

VIII. EXTERNAL LIGHTING

1.0 NS-26 Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of 45W

LED Post Top Light including all fixing accessories as required. (For 4 Mtr. High

2.0 NS-27 Supply, Installation, Testing & commissioning of outdoor type (IP 65) Bollard Light

100 mm dia, 1000 mm height made out of cast aluminium, 8 up to 10 W LED Light

with minimum 340 lumen, 100 lumen / watt, warm white, stainless steel screw,

corrossion & UV resistant coat etc as complete as required. 4 Each 16779.00 0.00 67116.00

3.0 NS-28 Supply, Installation, Testing & Commissioning of Recessed Inground Up Light fixture

20 Watt LED , integral driver, protection IP 66, CLASS I as complete as required.

(Tree Up Lighting) 6 Each 10487.00 0.00 62922.00

4.0 NS-29 Supply, Installation, Testing & Commissioning of Recessed Inground Up Light fixture

12 Watt LED , integral driver, protection IP 66, CLASS I as complete as required.

(Shrub Up Lighting) 4 Each 54701.00 0.00 218804.00

5.0 NS-30 Supply, Installation, Testing & Commissioning of Step Light fixture 3 Watt LED,

integral driver, protection IP 66, CLASS I as complete as required. (Building Entry)

6.0 NS-31 Supply, Installation, Testing & Commissioning of 36 Watt LED Light, integral driver,

protection IP 66, CLASS I as complete as required. (Building Entry) 2 Each 7306.00 0.00 14612.00

7.0 NS-32 Supply, Installation, Testing & Commissioning of 20 Watt LED Light, integral driver,

protection IP 66, CLASS I as complete as required. (Security Light) 2 Each 5681.00 0.00 11362.00

8.0 NS-33 FEEDER PILLAR (OUTDOOR TYPE)-

Digitally signed by SANGRAM

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing &

commissioning of cubicle type totally enclosed free standing type moisture, dust,

vermin & weather proof Floor Distribution Panel made out of 2.0 mm thick & front

cover 1.6 mm thick CRCA sheet complete with following equipments, including

digital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt

voltmeter selector switch, indicating lamps, CT's, internal wiring with suitable size

wires / cable, MS Angle stand for installation, RCC foundation, interconnection,

painting complete as per specification & drawing.

EXTERNAL LIGHTING PANEL

1 No. 63 Amp FP Moulded Case Circuit Breaker.

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No. 63 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

100 Amp TPN aluminium busbar.

3 No. 40 Amp DP MCB, 10 KA breaking capacity.

3 Set 24 Hrs TSQ Timer

3 Set 63 Amp, DP Contactor & A/M switch and Push Button.

21 No. 25 Amp SP MCB, 10 KA breaking capacity.

02 No. 40 Amp DP MCB, 10 KA breaking capacity.

01 No. 25 Amp DP MCB, 10 KA breaking capacity.

Panel described as above 1 Each 174104.00 0.00 174104.00

TOTAL SH-VIII CARRIED OVER TO SUMMARY 0.00 640369.00

IX. 20 KVA DG SET & ACCESSORIES

1.0 NS-34 20 KVA RADIATOR COOLED D.G. SET IN ACOUSTIC ENCLOSURE

1.1 Providing, installation testing & commissioning of 'Silent Type' Diesel Generating Set

along with having prime power rating 20 KVA, 415 Volts at 1500RPM, 0.8 lagging

Factor at 415 V suitable for 50 Hz, 3 phase system and for 0.85 load factor including

AMF panel and consisting of the following:-

a) Diesel Engine

Diesel Engine 4 stroke radiator cooled, electric start, of suitable BHP at 1500 RPM

suitable for above output of alternator at 400C, 50% RH & at 1000 metre MSL and

confirming to BS 5514, BS 649, is 10000, capable of taking 10% overloading for one

hour after 12 hours of continuous operation. The engine will be fitted complete with all

the required accessories.

b) Engine Mounted Instrument Panel fitted with and having digital display for following:

(i) Start- stop switch with key.

(ii) Water Temperature indication

(iii) Lubrication Oil pressure indication

(Iv) Battery charging indication

(v) RPM indication

(vi) Over Speed trip Indication

(vii) Low lubrication oil trip indication

(viii) Engine Hours Indication

c) Alternator:

Digitally signed by SANGRAM

Synchronous alternator rated at 20 KVA, 415 Volts at 1500 RPM, 3 phase 50 Hz, AC

Supply with 0.8 lagging power factor at 400C, 50% RH & at 1000 metre MSL. The

alternator shall be having SPDB enclosure, brushless, continuous duty, self-excited

and self-regulated through AVR confirming to IS:4722/ BS 2613 suitable for tropical

conditions and with class- F insulation. Alternator shall have provision of end

termination of Aluminium Bus Duct.

d) Base Frame & Foundation

Both the engine and alternator shall be mounted on suitable base frame made of MS

channel with necessary reinforcement which shall be installed on suitable cement

concrete foundation and vibration isolation arrangement as per recommendations of

Daily service fuel tank of 990 litres capacity, fabricated out of 3mm thick M.S. sheet

complete with all standard accessories and fuel piping between fuel tank and diesel

engine with MS class 'C pipes of suitable dia. Complete with valves level indication &

accessories as required as per specifications.

f) Exhaust System :

Dry exhaust mainfold with hospital grade exhaust silencer.

g) Starting System:

24V DC starting system comprising of starter motors: voltage regulator and

arrangement for initial excitation complete with 2 Nos. of batteries (25 plates, 160 AH

lead Acid type) as required as per specifications.

h) Accoustic and weather proof enclosure with arrangement for fresh air intake for

cooling of the engine & alternator, extraction, discharging hot air into the atmosphere

as per specifications. The Acoustic Enclosure shall be factory fitted by the OEM.

i) DG Exhaust pipe

Diesel Generating Set 20 KVA including Acoustic Enclosure. described as above.

TOTAL SH-IX CARRIED OVER TO SUMMARY 0.00 519103.00

X. SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Digitally signed by SANGRAM

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power

Plant conforming to MNRE specifications as amended, consisting of Mono/Poly

Crystalline silicon solar cells, net metering facility, necessary protections, earthing,

mounted on Aluminium/GI structure of suitable strength with following components

complete as required:-

a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India,

conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar

Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules

used in solar power plants/ systems must be warranted for their output peak watt

capacity, which should not be less than 90% at the end of 10 years and 80% at the

end of 25 years.

DSR-Solar b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V

Photovoltai AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC

c Power Power with efficiency not less than 97%, total harmonic distortion less than 3% and

Plant suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the

voltage and frequency level to suit the Grid Voltage Frequency.

c) Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP 65 protection and

termination arrangement for incoming and outgoing cable along with glands, lugs

and other accessories etc. as required.

e) Lightning and surge voltage protection.

f) Connections & Interconnections by supplying & fixing required size XLPE

insulated copper conductor 1.1 kV grade armoured power and control cables

between solar modules, main power cable to grid supply PCU unit along with

supplying & fixing of necessary channel/conduit lugs and other accessories etc. as

TOTAL SH-X CARRIED OVER TO SUMMARY 325336.42 0.00

XI CCTV SYSTEM

1.0 NS-35 Supply ,Installation, Testing , Commissioning, Integeration of 16-Channel 4K NVRs:-

Third-party network cameras supported

Up to 5 Megapixels resolution recording With 2 SATA Port up to 12 TB Supported

Support 1-ch HDMI, 1-ch VGA, HMDI at up to 4K(3840x2160) resolution

4-ch network cameras can be connected with 40M/60M/80M incoming bandwidth

Support dual-os to ensure high reliablility of system running

Support various VCA detection alarm and VCA search

Support H.265/H.264/MPEG4 video formats

2.0 NS-36 Supply ,Installation, Testing , Commissioning, Integeration OF outdoor 4 MP

IP BULLET 30 MTR CAMERA PVC BODY :- 1/2.8” Progressive Scan CMOS

Up to 2 megapixel resolution ,Full HD1080p real-time video ,120dB Wide Dynamic

3D DNR ,EXIR high performance LEDs Up to 30 meters IR range

12V DC±25% & PoE(802.3af Class3) Support H.264+ IP67

3.0 NS-37 Supply ,Installation, Testing , Commissioning, Integeration OF 4 MP Indoor IP

BULLET 30 MTR CAMERA PVC BODY :- 1/2.8” Progressive Scan CMOS

Up to 2 megapixel resolution ,Full HD1080p real-time video ,120dB Wide Dynamic

3D DNR ,EXIR high performance LEDs Up to 30 meters IR range

12V DC±25% & PoE(802.3af Class3) Support H.264

4.0 NS-38 Supply ,Installation, Testing , Commissioning, Integeration of SURVILLANCE HDD 4

TB - (UP TO 15 to 20 DAYS RECORDING) 2 Each 20029.00 0.00 40058.00

Digitally signed by SANGRAM

5.0 NS-39 Supply ,Installation, Testing , Commissioning, Integeration of 8 port POE Switch

6.0 NS-40 Supply ,Installation, Testing , Commissioning, Integeration of 6u Rack With PDU,

cable manager 1U metal , hardware pkt and Fan for POE Switches 1 Each 13267.00 0.00 13267.00

7.0 NS-41 P& F of RJ-45 Connectors 12 Each 69.00 0.00 828.00

8.0 NS-42 P&F of 32" LED Monitor Commercial ( LFD) 1 Each 29857.00 0.00 29857.00

9.0 NS-43 Provoding & Fixing of stand for camera 6 Each 1462.00 0.00 8772.00

10.0 NS-44 P& F of Cat -6 Cable Network Cable 150 Mtrs 68.00 0.00 10200.00

11.0 NS-46 P& F of 2 Core 1.5 sqmm Power Cable 20 Mtrs 72.00 0.00 1440.00

Video Door bell :-Supply, installation, testing, and commissioning of a smart

video door phone system, comprising a 7-inch touch display with a resolution

of 1024x600, adjustable brightness, contrast, and color settings, colored

night vision, and talkback functionality. The system supports Wi-Fi. Features

12.0 NS-47 include door lock release, motion detection, automatic voice messages, call 1 Nos 14802.16 14802.16

forwarding, do-not-disturb mode, camera 1080p, and storage for up to 60

images and 10 videos. The system supports two HD CCTV cameras, point-to-

point intercom, and has an IP64-rated 2MP AHD outdoor camera with a 110-

degree viewing angle. Complete with 16 melody options, adjustable

microphone and speaker volume, and an angular bracket for mounting.

TOTAL SH-XI CARRIED OVER TO SUMMARY 0.00 279764.16

1.0 1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor

PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in

the existing surface/ recessed steel/ PVC conduit as required.

2.0 1.24.7 Supplying and fixing following modular TV antena socket on the modular plate &

switch box including connections as required. 6 Each 148.00 1.06 0.97 1.03 157.71 946.28 0.00

Supply, erection, testing and commissioning of 6 way splitter of aluminium die cast

body in suitable size of G.I. Box.

Supplying and fixing of following sizes of medium class PVC conduit along with

4.0 accessories in surface/recess including cutting the wall and making good the same in

case of recessed conduit as required.

TOTAL SH-XII CARRIED OVER TO SUMMARY 18110.36 761.00

XIII DATA, WIFI AND TELEPHONE SYSTEM

1.0 1.18.1 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

recessed steel/ PVC conduit as required. 600 Mtrs 31.00 1.06 0.97 1.03 33.03 19820.69 0.00

Digitally signed by SANGRAM

2.0 1.24.6 Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for

Data, Voice & Wi-Fi rack end etc as per technical specification. 12 Each 148.00 1.06 0.97 1.03 157.71 1892.56 0.00

3.0 9 U Data Rack Supply,Installation, testing and commissioning of following 19"

Networking Enclosure Closed rack with

Front Glass door, rear steel door, castors, fans with fan tray, power distribution units

and complete with all accessories

as required along with Horizontal Cable manager and vertical Cable manager

complete as required.

4.0 Supply, installation, testing, and commissioning of a 16-port PoE (Power over

Ethernet) network switch with 1 uplink (W) and 1 SFP slot (SB), suitable for powering

NS-50 IP devices such as WiFi access points, IP cameras, and VoIP phones. Includes all

necessary accessories and integration with the existing network infrastructure

5.0 16 port patch panel Supply & Installation of Cat 6 Modular Jack Panels for

accommodating 16 port termination and shall

facilitate cross-connection and inter-connection using modular patch cords and shall

conform to EIA standard, 19-inch

relay rack mounting requirements. Patch Panel shall come with preloaded

NS-51 information outlets of non PCB and pyramid

type using lead frame technology.Panel shall have label holders and designation

labels as part of the standard device.

Shall also come with rear cable management metallic tray with velcro ties complete

as required and as per technical

specifications.

16 port patch panel 2 Each 10382.00 0.00 20764.00

6.0 2 Meter patch cord Supply & Installation of LSZH Cat 6A Mounting Cords 2 meter

length for the Patch Panel End

Connectivity, Both end shall be RJ 45 with snagless boots complete as required.

2 meter patch cord 6 Each 311.00 0.00 1866.00

7.0 8- Port Loaded LIU (Supply, laying , installation, testing and commissioning 8 Port

NS-53 LIU with loaded LC -LC coupler and adaptor plates etc. with necessary accessories to

complete the job)

8 port LIU OFC Unit 1 Each 12458.00 0.00 12458.00

8.0 Supply, installation, and commissioning of an enterprise-grade dual-band WiFi 6

NS-54 access point with PoE support, including mounting accessories and configuration.

Includes testing and integration with the network. 9 Each 19238.00 173142.00

9.0 Istallation, testing, and commissioning of an IP PBX telephone exchange system

supporting 100 extensions and 2 main (trunk) lines. 1 Each 158371.00 158371.00

10.0 Supply, installation, testing, and commissioning of standard telephone instruments

NS-56 with caller ID display, hands-free speaker, redial, mute, and speed dial functions,

suitable for use with the IP PBX system. 10 Each 1523.00 15230.00

11.0 Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including cutting the wall and making good the same in

case of recessed conduit as required.

TOTAL SH-XIII CARRIED OVER TO SUMMARY 41917.57 427511.00

XIV AUTOMATED BOOM BARRIER SYSTEM

Digitally signed by SANGRAM

1.0 Supply & Installationof Boom Barriers- Model New Up & Down 6 meter Length of

Boom : upto 6 M Double site open Duty Cycle: Intensive Opening- Closing Time : 2.5-

4 seconds(Adjustable) With –in Built crash protection feature manual over-ride,

Integration with Smart card and proximity reader, Along with push button for opening

and closing of Barrier With Safety rubber at bottom. Photocell included for auto

TOTAL SH-XIV CARRIED OVER TO SUMMARY 0.00 138702.00

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

S.N DESCRIPTION Amount (DSR) Amount (NSR)

A PLUMBING WORKS

1 SUB HEAD-1.0 SANITARY INSTALLATIONS 1,98,702.08 8,21,586.44 10,20,288.52

4 SUB HEAD : 4 - EARTH WORK, CONCRETE WORK 75,973.77 - 75,973.77

5 SUB HEAD : 5 , RAIN WATER HARVESTING - 1,61,963.60 1,61,963.60

Digitally signed by SANGRAM

PROJECT:-CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

Total DSR (incl DSR Amount Total Amount

Total DSR (incl DSR Amount Total Amount

S. No. DSR 2023 Description Unit RESIDENCE External DSR in Rs. Cess factor Cost Index NSR in Rs. NSR Amount

Quantity factors) in Rs. (DSR+NSR)

SUB HEAD-1.0 SANITARY INSTALLATIONS

Providing and fixing white vitreous china extended wall mounting water closet of

size 780x370x690 mm of approved shape including providing & fixing white

1 17.78 vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre Each 6 6 14,999.15 0.973 1.03 15,032.00 90,191.99 - 90,191.99

(adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts

and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single

hole basin mixer of approved quality and make, including painting of fittings and

brackets, cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass

single hole basin mixer

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink of approved make

as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including

painting of fittings and brackets, cutting and making good the walls wherever

17.10.1 Kitchen sink with drain board - - -

Providing and fixing approved make hand shower (Health faucet) of 1.2mtr long

4 NSR 1 with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 Each 6 6 3,741.81 - 22,450.88 22,450.88

litre per minute at 3 bar in chrome finish and wall hook.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make

and as per the direction of Engineer-in-charge.

17.28 Providing & fixing heavy quality PVC waste pipe for sink including PVC waste

fitting Complete

17.28.2 Flexible Pipe - - -

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of

7 17.31 approved quality) complete with 6 mm thick hard board ground fixed to wooden Each 6 6 5,955.37 0.973 1.03 5,968.41 35,810.48 - 35,810.48

cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on

anodised aluminium angle frame with C.P. brass brackets and guard rail complete

fixed with 40 mm long screws, rawl plugs etc., complete.

9 17.34 Providing & fixing toilet paper holder - - -

Providing, Fixing, Jointing, testing and commissioning of uPVC SWR pipe type 'B

as per IS 13592, solvant joint for sunken type for suspended with molded fittings

as per IS-14735, concealed in wet or dry walls including all fittings such as bends

in proper alignment, Y, Tee, junction, vent cowls, offset, access pieces (Plain or

door), Exposed pipes will also be provided with painting of legends with direction

arrow. etc. As per approved shop drawing. Cost shall includes fixing at wall /

ceiling level making holes complete with necessary hydraulic test. All pipe

supports shall be of MS hot dip galvanised with 85 micron galvanisation with

rubber insert(sizes indicated are nominal outside diameter)

Providing, fixing, testing and commissioning of uPVC inlet hopper with two or

three inlets fittings to receive waste pipes from fixtures waste. The hopper shall

be fabricated from 110 mm dia upto 600 mm long pipe complete etc. as per

engineer in charge.

Digitally signed by SANGRAM

Providing, fixing, testing and commissioning of uPVC P trap (FLOOR TRAP) of self

NSR -4 cleaning design with screwed down or hinged grating without vent arm with

12 BASED ON Setting in cement concrete 1:2:4 mix complete and provision for connecting inlet Each 8 8 1,638.48 - 13,107.81 13,107.81

DSR fitting complete including cost of cutting and making good the walls and floors.

110 mm OD inlet and 110 mm OD outlet.

NSR -5 Providing, fixing, testing & commissioning of Floor drain made of uPVC reducing

13 BASED ON elbow (110x63 mm) with horizontal drain outlet of 63 mm OD, round top of 110 Each 6 6 976.81 - 5,860.86 5,860.86

DSR mm OD. (Floor Drain)

Providing & fixing Autometic soap dispenser of approved brand & make of

14 NSR - 6 approved quality and colour, complete as per direction of Engineer in Charge. Each 5 5 3,279.63 - 16,398.13 16,398.13

NSR - 7 Providing, Fixing of CP brass Towel Ring with CP brass wall brackets and

15 BASED ON providing & fixing CP brass screws complete as required. Each 4 4 2,274.11 - 9,096.44 9,096.44

Supply and installation of the towel shelf 600 mm long in a Polished Chrome finish

consisting of space for folded towels along with a dedicated bar for hanging wet

towels. Rate shall include all required hardwares, screws etc complete as per

drawing and as directed by EIC.

17 NSR - 9 Providing & fixing soap dish holder of approved design. Each 4 4 1,356.17 - 5,424.68 5,424.68

Providing and fixing CP brass single lever low flow wall mounted Sink mixer with

15 mm CP brass single lever swivel spout with waste complete with flow rate 2.5

litre per minute at 3 bar including cutting and making good the walls where

Providing and fixing of Shower set as per following deatails-

Concelaed type CP Brass diverter(for hot and cold water), overhead shower

with arm with rubit cleaning system with flow rate 6 litre per minute at 3 bar,

19 NSR 11 hand shower, CP valves etc complete with all accessories as required and Each 4 4 19,834.77 - 79,339.10 79,339.10

spout with flow rate 3.8 litre per minute at 3 bar, wall flange complete with all

accessories as required and making good the walls wherever required.

Providing,Fixing wall mounted of approved make Double Coat hook on door

Providing and fixing CP brass 2 Way Bib cock with wall flange with flow restrictor

with flow rate 2.5 litre per minute at 3 bar.

Providibng and fixing straight type approved make single body push fit type WC

pan connector with factory supplied spring loaded seal guard of approved make

22 NSR 14 with integral single mould sealing fins made of flexible EVA body, including Each 6 6 709.11 - 4,254.65 4,254.65

bush/adaptor for use with C.I. Pipe as supplied with the pan connector.

Supplying, fixing, testing and commissioning of uPVC agricultural pipes

(6Kg/sqcm) conforming to IS 4985 for waste connection from wash basin to floor

trap/anti syphonage pipe with solvent cement joints, including all the fittings, laid

23 NSR 15 in the sunken slab etc, the work shall include wall chase and making good the

same in cement mortar etc., complete.The quoted rate should include necessary

supports like hanger supports, grip bolts and clamps etc.

Providing, fixing, testing and commissioning of uPVC clean out plug for

24 NSR 16 suspended pipes, with suitable inlet key for opening, complete as required.

Providing and fixing Cockroch Trap /Jaali of 125 mm dia of approved quality and

colour complete as per direction of engineer in charge.

25.1 (a) Circular Type - - -

Digitally signed by SANGRAM

25.1.1 i 125 mm nominal dia with 25 mm with waste hole Each 9 9 844.60 - 7,601.39 7,601.39

25.1.2 ii 125 mm nominal dia without waste hole Each 2 2 712.91 - 1,425.81 1,425.81

Providing & Fixing of Bathroom Drain with Sealing flange with removable trap,

(Storage Water Height 50 mm-Water Seal), with protection plug with Three rotable

26 NSR 18 supply DN50, with horizontal drain socket, with outlet 70/ 100 mm. (Body and Top Each 6.00 6 2,898.53 - 17,391.19 17,391.19

Frame made of environmentall friendly PP (poly propylene)

Providing, Installing & fixing storage type water heater (Geyser) of approved

make (vertical/horizontal type ) with copper container, glasswool insulation,stove

enamelled M.S jacket, thermostatically controlled inner heater with pilot neon

lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible

connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm

complete as required.

Providing, Installing & fixing storage type instant water heater (Geyser) of

approved make (vertical/horizontal type ) with copper container, glasswool

insulation,stove enamelled M.S jacket, thermostatically controlled inner heater

with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia

C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8

kg/sqcm complete as required.

Providing, installing, testing and commissioning of Domestic RO system

storage capacity 9 Letre, 20 LPH with inbuilt storage tank.

RO+UV+UF+TDS Control+UV In-tank, and Zero Water Wastage

Technology complete with all accesseries as required.

TOTAL OF SUB HEAD 1 - SANITARY INSTALLATIONS 1,98,702.08 8,21,586.44 10,20,288.52

SUB HEAD-2.0-WATER SUPPLY

NSR-22 Supply and Application of closed cell elastomeric insulation with glass cloth

facing and UV treatment (XLPE) in tubing form/ flat sections for Hot water piping

as per the specifications including all required accessories, protection as per

manufacturer's recommendations, complete in al respect. Quoted price shall be

inclusive of LEED Compliant adhesive and aluminum cladding as per

specifications.

6 mm thick (Concealed Pipes) & 13 mm thick (Exposed Pipes)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc. - -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

Internal work - Exposed on Wall - - -

Digitally signed by SANGRAM - -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded

33 18.9 fittings This includes jointing of pipes & fittings with one step CPVC solvent -

cement, trenching, refilling & testing of joints complete as per direction of Engineer

External Work - - -

Providing and fixing motorised butterfly valve rating PN 1.0 with float type sensors

suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with

control panel and sensors to open valve when water level is low in tanks and to

close when water level is high in water tanks including butterfly valves,

necessary cables, conduits, upto junction box etc. complete.

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal

35 NSR 24 flanged end & PN 16 rating as specified. -

Making rain water khurras 45 x 45 cm with average minimum thickness 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size) over PVC sheet 1 m x 1 m x 400 micron, finished with 12 mm

plaster in cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat

of neat cement including rounding of edges and finishing of outlet complete in all

Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :

38 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions : - -

Providing and filling sand of grading zone V or coarser grade, allround the G.I.

pipes in external work :

Providing and placing on terrace (at all floor levels) polyethylene water storage

tank, IS : 12701 marked, with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the

base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming

to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixture and geyser points

of approved quality confirming to IS: 8931.

Providing and fixing C.I. double acting air valve of approved quality with bolts,

43 18.59 nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be -

paid separately) :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality

Digitally signed by SANGRAM

Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire

45 NSR 27 mesh perforated sheet basket with necessary flange/ unions nuts, bolts and -

washers complete as required.

Water Meter :- Providing, Installing and Giving satisfactory field testing of Static

(Ultrasonic) Domestic Battery operated, MID (Measuring Instrument Directives)

approved Static AMR Water Meters diameters having no moving/fixed part in

contact with water, with fully body made up of composite material, confirming to

ISO 4064 along with manufacturing test certificate and Guarantee certificate with

Meter & Battery Guaranteed up-to 10 years with RF Technology for

communication. Memory of the device should be directly accessible through an

optical scanner.

Providing, laying and joining in position HDPE pipes with slipon flange, High

density Poly Ethylene pipe and conforming to I.S. 4984-1995 of required

grade / class, 08 kg/sq.cm pressure and suitable for the respective working

47 NSR 29 pressures with all fittings and specials, e.g. couplings, tees, bends, reducers,

screwed adapters, flanged tail pieces, etc., jointing as per manufacturers

recommendations, all complete including trenching, backfilling & pressure testing

etc. (For Irrigation System).

TOTAL OF SUB HEAD - 2 -WATER SUPPLY 3,77,312.31 1,36,829.13 5,14,141.44

1 SUB HEAD : 3.0- DRAINAGE

Providing, laying and joining in position HDPE DWC (Double Wall Corrugated)

and conforming to I.S. 16098 of required grade SN-4/SN-8 and suitable for the

respective working pressures with all fittings and specials, e.g. couplings, tees,

48 NSR 30 bends, reducers, screwed adapters, flanged tail pieces, etc., jointing as per

manufacturers recommendations, all complete including trenching, backfilling &

pressure testing etc. (For Sewer & Storm water line).

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10

49 19.2 graded stone aggregate 40 mm nominal size) all-round HDPE pipes/ RCC -

pies/S.W. pipes including bed concrete as per standard design:

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I.

grating brick masonry chamber with water tight C.I. cover with frame of 300 x300

mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be

not less than 2.70 kg as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III)

: 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal

51 19.7 size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse - -

sand) finished with floating coat of neat cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) finished with a floating coat of neat cement complete as per

standard design :

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty)

455 x 610mm internal dimensiions total weight of cover and frame to be not less

than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks

with class designation 7.5

Digitally signed by SANGRAM

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

52 19.8 Extra for depth for manholes: -

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786

having minimum cross section as 23 mmx25mm and over all minimum length 263

mm and width as 165mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering besides necessary and

adequate anchoring projections on tail length on 138 mm as per standard drawing

and suitable to with stand the bend test and chemical resistance test as per

specifications and having manufacture's permanent identification mark to be

visible even after fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size) complete as per design.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of

required shape and approved quality

Making connection of drain or sewer line with existing manhole including breaking

into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered

on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a

floating coat of neat cement and making necessary channels for the drain etc.

Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement

56 19.27 mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC - -

horizontal grating with frame complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

TOTAL OF SUB HEAD 3 -DRAINAGE 3,79,912.04 1,73,902.31 5,53,814.35

SUB HEAD : 4 - EARTH WORK, CONCRETE WORK

Excavating trenches by mechanical / manual means of required width for pipe,

cables etc including excavation for sockets ,& dressing of sides ,ramming of

bottoms ,for all depth including getting out the excavated soil,& then returning the

soil as required, in layers not exceeding 20 cm in depth including consolidating

each deposited layer by ramming ,watering, etc and disposing of surplus

excavated soil as directed, within lead of 50m.

2.10.1 All kinds of soil -

2.10.1.2 Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia Metre 125 125 352.15 0.973 1.03 352.92 44,115.15 - 44,115.15

Excavating trenches of required width for pipes, cables, etc including excavation

for sockets,depth upto 1.5 m, including getting out the excavated matterials,

returning the soil as requred in layers not exceeding 20 cm in depth including

58 2.13 consolidating each deposited layers by by ramming, watering,etc. and stacking -

serviceable material for measurements and disposal of unserviceable matterial for

measurement and disposal of unserviceable matterial as directed within a lead of

2.13.1 Ordinary rock -

2.13.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 10 10 998.65 0.973 1.03 1,000.84 10,008.37 - 10,008.37

2.13.2 Hard rock (requiring blasting) -

2.13.2.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 10 10 1,493.60 0.973 1.03 1,496.87 14,968.71 - 14,968.71

Earth Work in excavation by mechanical means (Hydraulic / excavator ) manual

means over area (exceeding 30 cm in depth ,1.5m in width as well as 10 sqm on

plan) including getting out and disposal of excavated earth lead upto 50m and lift

upto 1.5m, as directed as engineer incharge.

TOTAL OF SUB HEAD : 4.0 - EARTH WORK, CONCRETE WORK 75,973.77 - 75,973.77

Digitally signed by SANGRAM

SUB HEAD : 5 , RAIN WATER HARVESTING

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over

areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including

disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be

levelled and neatly dressed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations

61 2.25 etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming Cum 14 14 253.95 0.973 1.03 254.51 3,596.17 - 3,596.17

and watering, lead up to 50 m and lift upto 1.5 m.

62 2.26 Extra for every additional lift of 1.5 m or part thereof in.

Providing and laying in position ready mixed or site batched design mix cement concrete

for reinforced cement concrete work; using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

63 5.33 concrete, to improve durability and workability without impairing strength; including

pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost

of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-

charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix

shall be payable separately. In case the cement content in design mix is more than 110%

of the specified minimum cement content, the contractor shall have discretion to either re-

design the mix or bear the cost of extra cement.

63.1 5.33.1 All works upto plinth level

63.1.1 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum Cum 2 2 8599.35 0.973 1.03 8,618.18 17,236.37 - 17,236.37

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°

landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral

64 5.3 stair cases up to floor five level excluding the cost of centering, shuttering, finishing & Cum 2 2 10719.30 0.973 1.03 10,742.78 21,485.55 - 21,485.55

reinforcement with1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm

Centring and shuttering including stutting, propping etc. and removal of form for:

5.9.3 Suspended floors, roofs, landings, balconies and acees platform Sqm 5 5 766.55 0.973 1.03 768.23 3,841.14 - 3,841.14

Steel reinforcement for R.C.C. work including supplying, straightening, cutting, bending,

66 5.22 placing in position and binding with GI binding wires (18 gauge) all complete above plinth

Providing and doing Brick masonary work with common burnt clay modular bricks of class

designation 7.5 in foundation and plinth in:

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as

per IS: 10910 on 12mm dia steel bar conforming to IS :1786 having minimum cross section

as 23 mm x 25 mm and over all minimum length 263mm and width as 165mm with

minimum 112mm space between protruded legs having 2mm tread on top surface by

ribbing or chequering besides necessary and adequate anchoring projections on tail

68 19.16 length on 138mm as per standard drawing and suitable to with stand the bend test and Each 4 4 487.10 0.973 1.03 488.17 1,952.67 - 1,952.67

chemical resistance test as per specifications and heaving manufactures permanent

identification mark to be visible even after fixing " including fixing in manholes with

30x20x15 cm cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone

aggregate 20mm nominal size )complete as per design.

Providing and fixing in position precast RCC manhole cover and frame of required shape

and approved quality.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method

prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing

70 23.1 and submitting strata chart/bore log, including hire & running charges of all equipments,

tools, plants & machineries required for the job, all complete as per direction of Engineer

–in-charge, upto 90 metre depth below ground level.

70.1 23.1.1 All types of soil

Digitally signed by SANGRAM

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized

PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including

required hire and labour charges, fittings & accessories etc. all complete, for all depths, as

per direction of Engineer –in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized

PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire &

labour charges, fittings & accessories etc. all complete, for all depths, as per direction of

Engineer-in-charge.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in

73 23.5 recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Cum 1 1 1302.30 0.973 1.03 1,305.15 1,305.15 - 1,305.15

Engineer-in-charge.

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the

74 23.6 recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, Cum 1 1 1309.00 0.973 1.03 1,311.87 1,311.87 - 1,311.87

all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in

75 23.7 recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per Cum 1 1 1309.00 0.973 1.03 1,311.87 1,311.87 - 1,311.87

direction of Engineer –in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing

76 23.8 gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all Cum 1 1 1479.25 0.973 1.03 1,482.49 1,482.49 - 1,482.49

complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap/shoe or spot welded plate to the

77 23.13 top of bore well housing/ casing pipe, removable as per requirement, all complete for

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of

78 23.14 tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size

TOTAL OF SUB HEAD 5 : RAIN WATER HARVESTING 161963.60

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

COST SUMMARY OF WATER SUPPLY WORKS

S.NO DESCRIPTION DSR NS

WATER SUPPLY WORKS

A) WATER SUPPLY PUMPS, DRAINAGE SUMP PUMPS & EQUIPMENTS 17389.50 861430.66

Digitally signed by SANGRAM

PROJECT: CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

NAME OF WORKS: WATER SUPPLY PUMPS, DRAINAGE SUMP PUMPS & EQUIPMENTS WORKS

DSR (incl NSR DSR Amount Total Amount

DSR (incl NSR DSR Amount Total Amount

DSR 2023 S.NO. DESCRIPTION UNIT QTY DSR in Rs. Cess factor Cost Index NSR Amount

factors) (Rs.) in Rs. (DSR+NSR)

1 The quantities given in the Bill of Quantities are provisional. The Client reserves the right to substantially increase or decrease the quantities of work or to totally omit any items of work if so required and the contractor shall not be

entitled to claim any extra or damages on these grounds.

2 The contractor should make himself acquainted with all conditions and situations prevailing at the site. The rates quoted by the contractor shall take in to account all such factors and nothing extra shall be paid for any

misjudgement or misunderstanding, especially on the plea that contractor was not aware of any particular situation or site conditions.

3 The classification of various items of works for purposes of measurements and payments shall be as per bills of quantities (BOQ). Except where distinguished by BOQ the rates shall apply to all heights, depths, sizes, shapes,

profiles, angles, curves, circulars, slopes and locations. They also cater for all cuts and wastes. No level wise separation shall be made for the rates. Likewise all heights of staging,formwork(if any), and scaffolding are covered by

the rates including wastage and multi stage propping for heights greater than one floor (if applicable) strictly as per drawings and as per directions of Engineer in Charge and nothing shall be paid extra in any account.

4 For items not covered by the Technical Specifications, the work shall be executed in accordance with relevant IS code with latest edition as directed by Engineer in charge/Owner. In the event; IS code do not cover any item, the

work for that item shall be executed strictly in accordance with the best engineering practice as directed Engineer in charge /Consultant/Owner and shall be acceptable to the Contractor.

5 Quoted BOQ Rates are for all heights, depths, levels, leads and lifts, protection to all Equipments till final handing over. All basic rate are mentioned is FOR at site which including, design manufacturering,testing, loading

,transporting to site, unloading, freight, transit insurance, shifting at designated place st site, stacking etc. but excluding of GST. Contractor shall take prior approval of base rate from Owner/Project Manager before procurement of

any material or equipment at site.

6 The Contractor shall obtain permission and prior rate approval in writing from the Engineer in Charge/Client, before executing any Extra/variation / replacement / substituted item or exceeding of quantity from bill of quantities.

7 The system installed shall strictly comply with the technical specifications and drawings shared along with the tender BOQ.All items of work under this Order shall be executed strictly to fulfil the requirements of Drawings and

Technical Specifications. Type of equipment, material specification, methods of installation and testing and type of control shall be in accordance with the Detailed specifications, approved shop drawings, approved make of list and

the relevant Indian Standards.

8 All equipments/materials are to be brought in original packing of manufacturer along with documents giving details of packing etc.

9 The rate for each item of work included in the Bill of Quantities shall, unless expressly stated otherwise, include cost of :

a. All materials, fixing materials, accessories, appliances tools, plants, equipment, transport, labour and incidentals required for testing, balancing, commissioning and completion of work called for in the item and as per Detailed

Technical Specifications and Drawings.

b. All Wastage on materials and labour.

c All requirements of Specifications, whether such requirements are mentioned in the item or not. The Specifications and Drawings where available, are to be read as complimentary to and part of the Bill of Quantities and any work

called for in one shall be taken as required for all.

d All equipment and material shall be IS approved. All equipment and material shall be inspected at manufacturer’s works as per relevant IS by the Owner or his representative before dispatch to site. The contractor shall arrange the

same without any additional charge.

e All General arrangement/shop drawings shall be approved by the Owner/Consultant before fabrication work starts. Contractor shall prepare & submit the GA/Shop drawings as per detailed contract terms & conditions.

f All Installation,Testing and Commissioning shall be as per relevant IS for equipment and installation. All these testing records are to be maintained and submitted for Owner / Owner’s representative.The cost of Providing & fixing of

Antivibration pads/isolators shall be included in the quoted rates and nothing shall be paid extra against it.

10 No alteration whatsoever is to be made to the text or quantities of this BOQ unless such alteration is authorised in writing by Owner/Consultant. Any such alterations, notes or additions shall, unless authorized in writing, be

disregarded when tender documents are considered.

11 The Contractor shall procure and bring Materials/Equipment to the site only on the basis of approved Technical specifications and approved drawings for construction and shop drawings and not on the basis of Bill of Quantities

which are approximate only. This also applies to the Contractor’s requisition for Owner supplied materials(if any).

12 The unit rate for all local equipment or materials (not being procured against duty benefit) in Indian Rupees shall include cost of equipment and materials including all taxes and duties and also including loading, transportation to

site, unloading to the designated location,forwarding,all insurance and including shifting and stacking including storage, installation, testing, commissioning and all other works required for the successfully installation, testing and

commissioning of the complete System.

13 Water Treatment Plant(WTP) design is indicative, however Contractor must ensure the required water quality from the water test report (to be arranged by the Owner/Consultant) of the available water at the site before

procurement of equipment. The vendor shall also ensure that installed WTP is competent to maintain the WHO STANDARD of the treated water strictly as per requirement and directions of the Owner/Consultant .

A) WATER SUPPLY PUMPS, DRAINAGE SUMP PUMPS & EQUIPMENTS

Digitally signed by SANGRAM

DSR (incl NSR DSR Amount Total Amount

DSR (incl NSR DSR Amount Total Amount

DSR 2023 S.NO. DESCRIPTION UNIT QTY DSR in Rs. Cess factor Cost Index NSR Amount

factors) (Rs.) in Rs. (DSR+NSR)

1.0 TRANSFER PUMP

Supply & assisting in Installation, Testing & Commissioning of Horizontal/Vertical

centrifugal pumps for filtration & softening system. The pumps shall be made of

CI casing, SS-304 Impellar, SS-304 shaft & sleeve, Mechanical Seal are

connected to a TEFC induction motor mounted on a common channel base

frame with coupling guard, Motor to be suitable for 415 ± 10%, 3 Phase, 50 ± 5%

Hz cycles AC power supply, Strainer at suction and other stater/panel

accessories and concrete foundation complete as required.

Duty Parameter of transfer pump

■ No. of pumps - 2 Nos. (1W+1S)

■ Capacity - 100 LPM

■ Head - 35 Mtr

■ HP - 2.0 (For each)

■ Including pump

Supply, fixing, Installation, testing & commissioning Set 1.00 143909.85 0.00 143909.85 143909.85

Foundation shall be part of Civil work and executed by Civil Contractor as per

pump manufacturer GA/Foundation drawings.

Vendor to submit the Technical submittal comprising of Technical data sheet,

1.2 performance curve, Technical catalogue, dimension detail, installation detail of

the proposed/selected model for review and approval of Consultant.

Hydropneumatic Pumping System With Variable Frequency Drive For

domestic water supply at Terrace Level

Supply, Installation, Testing, & Commissioning a pre-engineered, factory

fabricated, assembled & tested, fully integrated, highly efficient pump, skid

mounted, complete ready-to-connect packaged variable speed water pressure

booster station,pump fitted with a 3-phase, fan-cooled,permanent- magnet

synchronous motors,motor efficiency is classified as IE5 in accordance with IEC

60034-30-2.. The packaged variable speed water pressure booster station shall

be complete with vertical inline multi stage centrifugal pumps , high efficiency

IE5 motors.The motor integrated with dedicated frequency converter in the motor

terminal box. This enables continuously variable control of the motor speed,

which again enables adaptation of the performance to a given requirement.The

pump shall consist of Cast iron with CED coated base & head, SS-304 casing

chamber and impeller and SS-304 shaft along with TEFC motor & mechanical

seal, pressure transmitter, NRV, Isolation valve on delivery line. Isolation

valve(PN-16), stainer at suction. The pump shall be suitable for 415±10%

volts 3 phase AC. Supply, complete in all respects as per directions of Engineer

in charge.The intelligent multi-pump controller, the controller shall be mounted in

a control cabinet with an IP 41 enclosure of suitable rating, digital energy meter in

the control panel; Modbus for BMS; hot Dipped Galvanised suction and delivery

CED coated manifolds; isolation ball valves on suction and discharge of each

pump; non return valve on discharge side of each pump; flow meter with 4-20mA

output; hot dip galvanised common base frame; and diaphragm pressure vessel

■ Pump Head - Cast Iron

■ Pump Base- Cast Iron

Digitally signed by SANGRAM

DSR (incl NSR DSR Amount Total Amount

DSR (incl NSR DSR Amount Total Amount

DSR 2023 S.NO. DESCRIPTION UNIT QTY DSR in Rs. Cess factor Cost Index NSR Amount

factors) (Rs.) in Rs. (DSR+NSR)

■ Impeller-SS 304

■ Chamber-Ss 304

Motor stool-Cast Iron

Shaft sealCartridge type(SiC/Carbon)

Rubber parts-EPDM

Efficiency class-IE5

Insulation class-F

Enclosure class-IP 55

Supply Frequency-50Hz

Supply voltage-3X380-415V

Built in Thermistor-PTC

Enclosure class-IP 41

A dedicated intelligent multi-pump logic controller for control and monitoring of

pumps shall be from the pump manufacturer with easy interface graphical display

unit with key function. controller should able to monitor multiple operating

parameters (flow, inlet pressure, outlet pressure, instant flow estimation,

cumulative flow and speed etc) to calculate best operating algorithm to pump

sequence optimally. Mentioned features should be available, automatic pump

alternations for run time equalization, Programmable number of starts/stops per

hour to prevent pump hunting, Friction Loss Compensation, Redundant primary

sensor for pressure monitoring, soft pressure built-up, log graph display for key

paramters, Clock program for multiple set point for scheduled system operation.

Pressure tank capacity: (minimum 200 Ltrs capacity (approx.) or as per

manufacturer calculation / recommendation) Note: Back up calculation need to

be provided for the same. A pre-charged Carbon Steel body diaphragm tank

shall be fitted to the discharge pipe with a compatible Butyl-rubber diaphragm. It

shall supply water a very low flows to minimize frequent pump start and stop and

water hammering. There shall be complete separation between water and air

and there should be no contact between water and tank compounds to

avoid corrosion. Bladders shall be suitable for sufficient elasticity to permit

full expansion inside the tank to ensure better performance and longer working

Pressure Transmitter (0-10/16/25bar, based on system design pressure)

Pressure Gauge - 0-16bar

Suction & Delivery Manifolds - Hot Dip Galvanised Iron CED coated

All cast iron parts should be CED coated.

One non-return valve and isolating valves for each pump is provided in delivery

side and one isolating valve is provided in suction side.

No. of pumps - 2 Nos. (1W+1S) (for Domestic water supply at terrace )

Capacity - 200 LPM

Digitally signed by SANGRAM

DSR (incl NSR DSR Amount Total Amount

DSR (incl NSR DSR Amount Total Amount

DSR 2023 S.NO. DESCRIPTION UNIT QTY DSR in Rs. Cess factor Cost Index NSR Amount

factors) (Rs.) in Rs. (DSR+NSR)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded

3 fittings This includes jointing of pipes & fittings with one step CPVC solvent

cement, trenching, refilling & testing of joints complete as per direction of

Engineer in Charge.

4.0 VIBRATION ELIMINATORS :

Providing, fixing, testing & commissioning of rubber neoprene lined style arch

vibration eliminators suitable pressure.

4.1 Pressure Rating PN 16 :

5.0 Y - STRAINER :

Providing, fixing, testing & commissioning of Y type Strainer having cast iron

body [IS 210 Gr. FG 200], SS 304 Screen having 1.2 mm performation, Flange

end as per BS 10 Table F. Body Test Pressure shall be 20 kg/cm2 Hydroulic

complete with all Fitting & Drain Plugh & Accessories.

6.0 Ball Valve :

Providing and fixing brass ball valve suitable for 15kg/sqcm working pressure full

bore type with lever and female screwed ends, of approved quality.

7.0 NON-RETURN VALVE

Providing, fixing, testing & commissioning of CI wafer type single plate non-return

valve (PN 16) complete with 2 Nos. matching flanges, rubber insertion, nuts,

bolts and washer etc. of following sizes with locking arrangement.

8.0 BUTTERFLY VALVE :

Providing, fixing, testing & commissioning of level operated water type butterfly

valve conforming to IS : 13095/BS 5155 having CI iron body , ss 316 grade dick,

EPDM / nitride complete with 2 Nos. matching flanges, rubber insertion, nuts,

bolts and washer etc. of following sizes with locking arrangement. (including

8.1 Pressure Rating PN 16 :

Digitally signed by SANGRAM

DSR (incl NSR DSR Amount Total Amount

DSR (incl NSR DSR Amount Total Amount

DSR 2023 S.NO. DESCRIPTION UNIT QTY DSR in Rs. Cess factor Cost Index NSR Amount

factors) (Rs.) in Rs. (DSR+NSR)

Providing, fixing, testing & commissioning of dial type (150 mm dia) pressure

gauge with isolation ball valve suitable for working pressure of 250 PSI cost shall

be of inclusive of providing any short pieces, nipples, elbows etc as required.

having calibration of 0-15 Kg/cm2.(Glycrine filled)

10.0 Electronic Digital Type Turbine Flow Meter :

Providing, fixing, testing & commissioning of Electronic Digital Type Turbine Flow

Meter/Totalizer having following specification:(for UG tank)

● Internal Part (Roter) : Stainless steel SS 304.

● Mounting :Inline horizontal or vertical

● Reading : M3/Hour and Kilo-litter

● Flow rate display : 4 digitals LED.

● Totalizer display : 8 digitals LED.

● Output : 4-20mA (Integrated with BMS).

● Power supply : 220V AC/24 V DC

● Accuracy : ± 1%.

● Repeatibility : ± 1%.

● Operating temperature :0-50°C.

● Media : Liquid.

● Maintenace :"Provision of bypass arrangement (Piping & Valves) Each 1.00 32208.40 0.00 32208.40 32208.40

Providing, fixing, testing and commissioning of Fully Automatic micro-controller

based water level Controller and Water-Level LCD Display & motor protector

including sensor, Display Panel, cabling and all fitting and accessories (For

Underground & OH Water Tanks).

TOTAL OF WATER SUPPLY PUMPS, DRAINAGE SUMP PUMPS &

EQUIPMENTS CARRIED OVER TO SUMMARY

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

COST SUMMERY OF HVAC

S.NO DESCRIPTION DSR NS

Digitally signed by SANGRAM

PROJECT:- CONSTRUCTION OF CMD RESIDENCE AT PLOT NO. 69, GOLF LINK, NEW DELHI

S. No. DSR-2024 DESCRIPTION OF ITEM UNIT QUANTITY DSR Rate NSR Rate DSR Amount NSR Amount

Sub Head 'A'- Machinery

1 8.1 Air Cooled VRV / VRF Outdoor Unit

Supply, Installation,Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed

inverter type Scroll Compressor(s),minimum two compressors for above 14HP modules, microprocessor

based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration

isolators, with suitable foundation etc. complete as required. To have better efficiency condensor fan shall

be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity at

AHRI Conditions and work even at 50°C ambient temperature without tripping.The system shall be able to

deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the

refrigerant and ready for use as required. The condensor shall have protection coating to save from various

external conditions and the hydrophillic film to prevent water accumlating on the heat exchanger's

film.Equipment should be AHRI 1230 certified & NABL Accredited with standard ISO 17025:2005. (As per

ECBC , min efficiency of the system should be 3.28 EER and 4.36 IEER for Units less than 40 kW(14 HP) ,

3.26 EER and 4.34 IEER for Units between 40 kW(14HP) to 70 kW(24HP) and 3.02 EER and 4.07 IEER

for units more than 70 KW(24HP)) (Outdoor stand is not included)Complete as per CPWD

specification/drawings and as directed by Engineer-in-charge.

For Cooling and Heating

2 8.7 VRV Hi Wall Unit - Supply, Installation, Testing and Commissioning of following minimum capacity High

wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control,

drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single

phase AC supply, complete as required. The unit shall have automatic force shut

downvalve in case of fire on receiving signal from BMS System.The system shall be capable

to adjust air flow as per room requirement automatically. The cooling capacity of indoor

unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

(Make will be same as of Outdoor)

Digitally signed by SANGRAM

S. No. DSR-2024 DESCRIPTION OF ITEM UNIT QUANTITY DSR Rate NSR Rate DSR Amount NSR Amount

3 8.2 Indoor Cassetee Unit- Supply, Installation,Testing and Commissioning of following minimum capacity 4

way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media prefilter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil

section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, Corded remote control etc., suitable for operation

on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have

automatic force shut down valve in case of fire on receiving signal from BMS System. The

system shall be capable to adjust air flow as per room requirement automatically. The

cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature. (Make will be same as of Outdoor)

4 8.12 Y-joints For Indoor Unit

Supply Installation Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same

OEM make as of ODUs and IDUs

4.2 8.12.2 Outdoor Multi Joint Each 5.00 8877.00 44385.00

5 8.14 Supply Installation, Testing and Commissioning of wireless remote controller with receiver Each 10.00 4261.00

for VRF/VRV individual indoor units 42610.00

6 8.15 Supply Installation, Testing and Commissioning of Centralized Remote Controller.

Centralized Control with display for Operator interface to Manage Entire VRV/VRF System

from Single point. Minimun 64 indoor units must be controlled.

The following controls should be possible through this system:-

1) Temperature Controls, Each 1.00 71018.00 71018.00

2) ON/OFF Control,

4) Error Display

5) Connectable with Unified ON/Off controller, schedule timer and BMS system.

7 8.17 Insulated Refrigerant Piping for VRV / VRF System

Supply, installation, testing and commissioning of interconnecting high pressure copper refrigerant

piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated

with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell

structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL

94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping

shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside

the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on

insulation & cost to be included in the piping. Cable tray is quantified seperately.

7.1 8.17.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 50.00 263.00 13150.00

7.2 8.17.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 20.00 355.00 7100.00

7.3 8.17.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 100.00 500.00 50000.00

7.4 8.17.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 40.00 632.00 25280.00

Digitally signed by SANGRAM

S. No. DSR-2024 DESCRIPTION OF ITEM UNIT QUANTITY DSR Rate NSR Rate DSR Amount NSR Amount

7.5 8.17.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 70.00 759.00 53130.00

7.6 8.17.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation RMT 20.00 929.00 18580.00

Sub Head 'B' - HVAC Plumbing

8 NS Condensate Drain Piping With Nitrile Rubber Insulation

Supply, installation, testing and commissioning of UPVC condensate drain water piping of density 10

Kg/m³ complete with fittings like elbows, tees, reducers, bends, flanges, supports & duly insulated with

"O" class Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness etc. as

required and of following sizes.

8.1 25 mm dia pipe, 13 mm Insulation RMT 75.00 878.44 65883.26

Total HVAC Works 1202440.00 65883.26

Digitally signed by SANGRAM