SPECIAL REPAIRS TO BLDG NO 199 COOK HOUSE SPECIAL REPAIRS TO BLDG NO 200 TO 203 BATHROOM AND TOILET COMPLEX SPECIAL REPAIRS TO BLDG NO EM 26 JCO MESS AND PROVN OF TOILET BLOCK NEAR BLDG NO. EM91 AT NASIRABAD CANTT UNDER GE NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

Rough cast plaster with mixture of crushed or fine gravel aggregate (6 to 12 mm) mixed with coarse sand and cement in the ratio of 1:1:1 over and including 15mm thick under coat of cement and sand mortar 1:4 while it is still in plastic state, complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over a finished coat of white wall care putty (Make-Birla/JK/Asian) all as specified & as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of white wash complete all as specified and directed

M & L for preparation old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

M & L for preparation of new decorated surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab including rubbing & polishing complete all as spdspecified & directed.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate), complete all as specified and directed.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

M&L for glazed ceramic coloured tiles, size 450 mm X 300 mm, 6-7 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over 10 mm thick screed plaster in CM 1:4 complete all as specified and directed

M & L for Non-skid Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

All as per the item No 20.00 above but as in skirting ocer and including 10 mm thick screed plaster in CM 1:4 complete all as specified.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20 mm thick crushed stone aggregate) as in sub base complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered as directed.

M&L for random rubble stone walling uncoursed, built in CM (1:6) complete all as specified and directed.

All as per item No. 24.00 above but except stone.

M&L for brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

All as per item No. 26.00 above but except brick.

M&L for brick work with fly ash bricks straight or curved on plan to any radius, built in CM 1:4 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm as specified.

Demolition of Stone slabs & tiles of any description or thickness in floors , aprons etc, complete all as specified and directed.

M & L for 20mm thick black granite on kitchen platform and similar work over & including 15mm thick screed bed in CM 1:6 laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

S & F for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to rigid UPVC waste pipe bent to shape & fixed to wall with bracket overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge

Taking down old wooden plate rack and S&F stainless steel plate rack made of 0.50mm thick of over all size 920mm x 785 mm x 255 mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item No. 36.00 above but 20 mm bore .

All as per srl item No. 36.00 above but 25 mm bore

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item No. 39.00 above but 20 mm bore .

All as per srl item No. 39.00 above but 25 mm bore

S & F water tubing 20 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, laid in trenches, complete all as specified and directed.

Fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc.

All as per srl item No. 43.00 above but 20 mm bore

All as per srl item No. 43.00 above but 25 mm bore

S&F CI Nahani/Floor trap 75 mm outlet with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as in repairs.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed .

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but not exc 4 Sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed .

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) & cooler stand including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F for 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed.

M&L18/19mm thick block board grade-.II quality, interior grade with decorative type with decorative face veneer on one face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

M & L for 20 to 25 mm thick machine cut kota stone Shelves, window cill including rubbing & polishing and set in CM (1:4) incl cutting inserting into wall not less than 50mm deep and making good to disturbed surfaces complete all as specified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

M&L for IInd class H/W Plain , Solid , Straight chowkats and frames sec area n exe 40 sqcm complete and all as specified.

S & F 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed.

S & F 75mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S & F 300mm long aluminium alloy,anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F 125mm single action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Dismantling of existing unserviceable water tank of any description, capacity exc 500 Ltr but n.exc 1000 ltrs each complete all as specified and directed

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as spd & directed.

M&L for 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and including 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) finished concrete surfaces even & smooth complete all as specified and directed

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

Taking out of old grill & M & L for framed work such as grills, gratings, etc, with ends of bars shouledered and /or reiveted ,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work coforming to Fe 290m Gde E-165 complete all as spd and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc complete all as specified.

Taking down CI pipe 100/75 mm fixed wall and floor etc including accessories complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only old 100 mm bore CI pipe as on wall with new fixing clamps.

S& F 100 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only old 75 mm bore CI pipe as on wall with new fixing clamps.

S& F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

S& F 100 mm CI bend, fixed with cement solvent complete, all as specified and directed

S&F 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet squatting pattern ( Urissa pattern) with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed.

Taking out old unserviceable wash down water closet and S & F vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F in repairs PVC low level flushing cistern syphonic action type white with inlet ball valve, handle including brackets 10 ltrs capacity etc complete all as spcified and directed.

S & F in repairs PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc complete all as specified and directed

S&F in repairs 15mm bore cast copper alloy chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

S&F in repairs 15 mm Stop valves, cast copper alloy, chromimum plated, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc, including removal to store complete all as specified and directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with clamps complete all as specified and directed by the Engineer-in-Charge

Supply only stack clamp made out of 50mm by 3mm flat iron and 16 mm dia round iron stays fixed to pipe of bore 110mm complete all as specified.

S&F PVC bend/ shoe of dia. 110mm complete all as specified including taking down old unserviceable complete all as specified.

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as specified & directed.

Taking out old un serviceable tubular towel rail & S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as specified & directed.

M&L for ceramic coloured tiles matt finish 400 x 400 x 7mm thick coloured/ Jointless tiles in floors, set and jointed in neat cement slurry and pointed in white cement with coloured pigment to match with tile laid over and including screed bed or bedding layer 15mm thick in CM (1:6) laid over and including 25mm thick, PCC (1:2:4) type B-0 using 12.5 graded stone aggregate complete all as speciied and directed.

All as per serial item No. 103.00 above but on vertical surfaces of wall such as dados, skirting etc set and jointed in neat slurry and pointed in white or colour cement to match over 10mm thick screed plaster in CM 1:4 complete, all as specifed and directed.

S&F in repair brass chromium plated shower rose of 125mm size with swivel joints, incl . Fixing to steel pipe or union of 15mm bore complete all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and applying two coats of oil bound distemper over and including 1 mm thick wall care of putty complete all as specified and directed

M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for old concrete surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for 10mm thick vitrified ceramic tiles light shade (Square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified and directed.

All as per serial item No. 109.00 above but on vertical surfaces of wall such as dados, skirting etc set and jointed in neat slurry and pointed in white or colour cement to match over 10mm thick screed plaster in CM 1:4 complete all as specifed and directed

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

S&F in repairs fancy type 20mm dia SS curtain rods fixed to bracket complete all as spd & directed.

S&F decorative type knobs with bracket of Stainless Steel fixing at end of curtain rod complete al as spd & directed.

M&L for providing chequered cement concrete coloured tiles 25cm x 25cm x 22 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment laid over and including screed bed or bedding layer 20 mm thick in cm 1:4 as in floors complete all as specified and directed.

Taking down old unserviceable WHB and S&F wash hand basin vitreous china white /colour flat size 550 x 400mm fixed including waste coupling, waste pipe ,complete all as specified and directed.

S&F in repairs pillar taps fancy type cast copper allloy capston headed, chromium plated, screwed down, high pressure with long screwedshank and fly nut, screwed for 15mm bore iron pipe complete all as specified.

Excavation in trenched n exc 1.50 m in width and n exc 1.50m in depth for foundation , manholes , cespits, etc n exc 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed

M&l for PCC 1:4:8 type D-2 as in foundation and mass concrete complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for broken stone hard core of gauge n exc 63mm deposited spread and levelled in layers n exc 15 cm watered and rammed to a true surfaces complete all as specified and directed

Returning, filling in including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed

Filling under floor including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed

Removel of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above from the starting point complete all as specified and directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 grade (nominal mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge

M & L for M-25 grade (nominal mix) using 20mm graded aggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete , surface is required to be fair finished, complete all as specified and directed by the Engineer-in-Charge

M & L for RCC M-25 (nominal mix) using 20mm graded aggregates as in roof beams, lintel beams/bands, cantilevers, bressummers, lintels over 1.5m span, chajjas etc complete all as specified and directed by the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, soffits of lintel beams/ bands, chajjas, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., flat surfaces of concrete , surface is required to be fair finished, complete all as specified and directed by the Engineer-in-Charge

M & L for RCC M-25 (nominal mix) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished, complete all as specified and directed by the Engineer-in-Charge

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and directed by the Engineer-in-Charge

M&L for 15mm thick rendering on brick /concrete work surfaces in CM 1:4 finished fair and even without using extra cement using WPC as per manufactuere instructions (WPC is to be measured and paid separately)

M&L for 10mm thick redering on brick work surfaces in CM 1:6 finished fair and even without using extra cement complete all as specified and directed

S & F Vitreous China squatting pan, `Orissa` pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with long body PVC SWR suitable 'P' or 'S' trap complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC valve less syphonic action type, low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float and handle & flush pipe, fixed on walls by drilling holes and using PVC rawl plug of suitable size complete.

S & F PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F stop cock/angle cock 15 mm dia cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as spd & directed

S&F Soap dish fancy type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

S&F vitreous china wash hand basin white, flat back of size 550x400mm excl taps, and plug and porcelain stopper but including brackets, PVC waste pipe & PVC waste coupling complete all as specified and directed.

S & F of vitreous China urinal, flat back, half stall type white/ ivory colour with grating and Union for discharge pipe including connection to flushing pipe and outgoing waste pipe complete all as specified and directed by the Engineer-in-Charge.

S&F Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S&F grating square 125mm size of PTMT with centre hole movable or side hole for fix to waste pipe (min weight - 100 gms) complete all as specified and directed.

S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

M&L non skid ceramic coloured tiles 400x400x7 to 8mm thick in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade the tiles over 15mm thick plaster in CM 1:6 over and including 25mm thick PCC 1:2:4 at B-0 (using 12.5mm graded stone aggregate ) complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x450x7 to 8mm thick on vertical surfaces of wall such as skirting/ dados ect set and jonted in neat cement slurry and pointed in white cement to match the shade the tiles over and including 10mm thick screed plaster on stone/brick masonry walls in CM 1:4 complete all as specified and directed.

S & F Steel ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements, 25mm aluminium knobs to shutter, aluminium hook & eye, 10mm MS square bars in grill, 04 Nos lugs welded to frame Z section handle 100mm inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note :Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

Supply only integral water proofing compound , ISI marked.

S&F PVC floor trap with grating 75mm dia fixed with cement joint complete all as specified and directed.

Supply and fixing 500 Litre capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F for 110mm bore PVC (SWR) junction single (Single T) equal or unequal with oval access door, complete all as specified

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 110mm bore PVC (SWR) vent cowl, complete all as specified

M&L 40 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and M&L 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) finished conc. surfaces even & smooth complete all as specified and directed.

M & L for concrete bed to drain pipes of 150mm bore, including packing under, and haunching against the sides of pipes after they are laid and tested cement concrete 1:4:8 type D-2 complete all specified and directed

M & L for 5cm sand stone slabs in sun shades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all specified and directed.

M & L for PCC 1:2:4 Type B2 using 40 mm graded aggregate as in surface channels and drains & coping, edging rounded or chamfered type etc complete all specified and directed

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc complete all as specified..

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified.

Taking down MCB DB's/TPN complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc complete all as specified.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 171.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth S & F MCB TPN, 415 volt, 63 Amp capacity, 10 KA, 'C' curve, ete S & F MCB TPN, 415 volt, 63 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed.

S&F switch piano flush type 5 Amps, single pole one way 240 volts.

S&F switch piano flush type 15 Amps, single pole one way 240 volts.

S&F Socket outlet 3 Pin 5/6 Amp flush type.

S&F socket out let 2 in 1, multipurpose 3 pin 15/16 Amp flush type ISI marked complete.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt), 230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make :- Havells/Bajaj/Philips/Crompton as Approved by AO.

S&F LED light fitting 1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make :- Havells/ Bajaj/ khaitan/Usha as Approved by AO.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unserviceable existing earthing .

Supply only LED lamp 9/10 watt. Make :- Havells/ Bajaj/ Philips as Approved by AO.

S&F box type LED tube light fitting in acrylic linear tube 1x 20 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube rod 20 watt. Make :- Havells/Bajaj/Philips/Crompton as Approved by AO.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp and street light bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make- Havells/Surya/Control&Switchgear/Bajaj as Approved by AO.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. Make :- Havells/ Bajaj/ Philips as Approved by AO.

Supply and fixing testing and commissioning energy saving street light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make- Havells/Surya/Control&Switchgear/Bajaj as Approved by AO.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts for fixing of street light complete all as specified and directed by Engr-in-Charge.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F exhaust fans AC single phase 230V of size 300mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: Bajaj/Havells/Crompton.

M & L submain wiring with two single core, PVC insulated, unsheathed, FRLS, 1100 volts grade 2.5 Sqmm multi stranded copper conductor cable drawn through and including 25 mm dia PVC non metallic rigid conduits & conduits accessories, concealed in wall/ roof/ ceiling including one run of green colour earth continuity conductor with 2.5 Sqmm multi stranded copper conductor cable complete all as specified and directed. Note :- Two run of single core cable, one run of earth continuity conductor & conduit with conduit accessories shall be measured as one unit length.

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy. Make: Bajaj/Havells/Crompton.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, 5 Star rated & Glass lined enamel coated incoloy heating element, Temperature indicating dial & Shock-resistant ABS outer body complete with all accessories such as safety valve, thermostate, NRV, connection piece etc Make: Bajaj, Havells, Usha.

S&F recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey>100 Lm/w complete all as specified and directed. Make Crompton/Havells/Philips.

S&F single pole and neutral enclosure with a two pin and earth plug and earth plug and socket complete with one single pole 20 Amp MCB SP 'C' series for AC complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection .

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

S&F of MCB distribution board TPN 4 way, 415 with 200 Amps rated bus bar with shrouds, earth bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F MCB TPN, 415 volt, 63 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed.

M/S SHIVA TRADERS

M/s Jai Jinendra Constructions

H M LAXMINARAIN

M/S Bansal Construction

V K LAKWAL CONSTRUCTION

MAHARANI CONSTRUCTION