REPAIR TO COMPOUND WALL FENCING GATE AND OTHER MISC WORKS OF DOMESTIC AREA AT AF STN SIRSA

Amount

Demolition Cement Concrete (Un-Reinforced) of in Ground & Pavings. not exc. 150mm thickness (below or above Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Demolition Cement Concrete (Reinforced) of any description i.e., Beams, Staircase, Chajjas, Slab, Drain Couver etc and in any position complete and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Structural Steel or Mild Steel Work of any description including frame, truss,etc complete all as specified and as directed.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Dismantling Chain Link, weld mesh of any description i.e. any mesh, size and type, complete all as specified and as directed.

Dismantling Floor, Paver Tiles, Chequered Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Dismantling of one way Trellis work (jafri), including taking as under of battens in trellis (post and rails measured seperately) , complete all as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Excavating in Post Holes (or similar holes) in Soft/Loose Soil, Each not exc. 0.50 CUM, getting out, returning, filling in and ramming Earth or Broken Rubble mixed with Earth around in layers not exc. 25 Cm, watering and removing surplus Soil to a distance not exc. 50.00 Metre and making good surface, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (40mm crushed stone aggregate) in Foundation, Filling and Mass Concrete, etc. including Use and Waste of Formwork as required/ordered, complete all as specified and as directed.

M&L RCC Pre-cast Cement Concrete 1:2:4 (12.5mm crushed stone aggregate) as in Louvres and Jallies, 40mm thick (measured solid) with all mouldings including Reinforcement with 5.0 - 6.0mm dia Mild Steel Bars/ Wire and setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Cost of Mild Steel Bars/Wire as Reinforcement will deem to be included in the Quoted Unit Rate.

M&L for Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L for Brick Work with Sub-class ‘B’ Bricks but except Bricks (Serviceable Bricks obtained from BOQ Item No. 3 here-in-before including removing Mortar from Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L for Framed Work as in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for hanging or sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or Other Covering, Running Rails and Guides) and hanging; also fastening and fixing, conforming to Fe-410-W (Gde E-250), Quality A, complete all as specified and as directed.

M&L for Mild Steel Galvanised Chain Link Fencing including Line Wires with 3.0mm dia Wire of and type of Standard Rails, Straining Bolts, etc. including provision of Mild Steel Binding Wire not less than 0.90 mm dia, complete all as directed by Engineer in Charge.

S&F Welded steel wire fabric of weight per square metre not exc 4 Kg fixed to steel members complete all as specified and as directed.

M&L for Cement Concrete 1:4:8, type D-2 (40mm crushed stone aggregate) 75mm thick as in Fillings, Sub-base to Floors, etc. complete all as specified and as directed.

M&L for Pre-cast Reinforced Cement Concrete 1:2:4 (20mm crushed stone aggregate) in lintels landings, cover slabs (for man holes etc) chullah hoods, chajjas, water troughs, shelves, bressumers, steps,quoin blocks (for use with masonry),string courses, copings.kneelers, apex stones, pier caps,columns, posts,boundary pillars,bed plates, pintle, blocks, ancho-rage blocks, bonders(for stone wallin).corbels, brackets,etc. (of any section indicated), withplain fair faces,including chamfers,weatherings,throating etc. andsetting in mortarcomplete with joints to match NOTE : Reinforcement will be Measured and Paid separately under relevant Item.

M&L for TMT Bars 6.0mm to 8.0mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.

M&L for Cement Concrete 1:2:4 (20mm crushed stone aggregate), 40mm thick in PCC floor complete all as specified and as directed.

M&L for Cement Concrete 1:2:4 (20mm crushed stone aggregate), 75mm thick in Path/ Hardstanding in alternate Bay/Panel, finishing Cement Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L for Paver (Floor) Tiles of size 300x300x9.0 to 10mm thick, Coloured, highly abrasive and anti-skid, resistance to UV effect, impact resistance, laid over and including 15mm thick Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Chequered Cement Concrete Coloured (Terracota Red or Yellow) Tiles 300x300x25mm thick, Set, Jointed and Pointed in Neat Cement Slurry in Floors and Pointed in Grey Cement, laid over and including 20mm thick Cement Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : (a) Joint Filling of Tiles Shall be done immediately after laying tiles with cement and pigment to match the colour of tiles. Joint Filling of Tiles with cement slurry shall not be allowed. (b) Cost of screed Bed shall deemed to be included.

S&F Galvanised 2 strand, Steel Barbed Wire 2.24mm dia Barbed with 2.0mm dia Barbs at 75mm spacings and straining and fixing to any type of Standard Rails, Straining Bolts, including securing or tying at Crossings with and provision of Galvanised Mild Steel Wire, Staples or Steel Pins,etc., complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

M&L for Machine Pressed Pre-cast Concrete Interlocking Polished Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked, laid dry over Clean dry Sand and grouted with Clean dry Sand as in Floors, complete all as specified and as directed. NOTE : Clean dry Sand will be Measured and Paid separately under appropriate Item.

S&F for Rolled Mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting Plates, etc. Confirming to Fe-410-W (Gde-E-250) quality B (cut to ordinary lengths i.e. within 20mm of the length indicated), complete all as specified and directed.

M&L Sand Filling under Floors or in Foundations including Watering and Consolidation, complete all as specified and as directed. NOTE : Final sand conforming to Zone IV shall be used.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick Walls/Concrete Surfaces mixing with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : WPC shall be Measured and Paid for as ‘Supply only’ separately under appropriate Item.

Supply only Integral Water Proofing compound, conforming to IS and as approved, complete all as specified.

M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the ratio 1:1:1 shall be applied and finish Even, complete all as specified and as directed.

M&L for Preparing New Plastered Surfaces of Walls by applying wall care putty, cutting / rubbing to obtained a smooth surface and applying Two Coats of Weather Coat Exterior Paint with approved Tint over a coat of Primer as per manufacturer's instructions, complete all as specified and as directed.

M&L for Preparing New Rough Cast Plastered Surfaces of Walls by applying Two Coats of Weather Coat Exterior Paint with approved Tint over a coat of primer as per manufacturer's instructions, complete all as specified and as directed. NOTE: Painting shall not be carried by spray gun

M&L for Preparing Old Decorated/Treated Plastered Surfaces of Walls by brooming down or steel wire brushing and crapping down and applying One Coat of Weather Coat Exterior Paint with approved Tint as per manufacturer's instructions, complete all as specified and as directed.

M&L for Preparing Old Decorated/Treated Plastered Surfaces of Walls by complete removal of existing treatement , Cutting/Rubbing to obtain a smooth surface and applying Two Coat of Weather Coat Exterior Paint with approved Tint as per manufacturer's instructions, complete all as specified and as directed.

M&L for Preparing Old Treated/Painted (Rusted) Steel and Iron Surfaces of any description, and applying Two Coat of Synthetic Enamel Paint (First quality) for Y shape Mild steel Angle Frame ( area exc 0.25 Sqm but not exc 0.50 Sqm Each) fixed on boundary walls (Straining /Supported to barbed Wire and Concertina Coil) complete all as specified and as directed. NOTE: Painting shall not be carried by spray gun

M&L for Preparing Old or previously treated Plastered/ Concrete Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L for Granite (of any type) Tiles 16-18 mm thick machine cut, in skirting/dado/pillars & vertical surfaces laid over cement screed and jointed with grey cement slurry, and pointed with white cement and admixture of pigment to match the shade of granite stone including grinding, polishing including 10mm thick rendering in Cement Mortar 1:4 complete all as specified and as directed. NOTE : Cost of Cement rendering shall deem to be include in the Quoted Unit Rate.

M&L for Providing and laying at or near ground level factory made kerb stone of grade 1:2:4 (20mm graded stone aggregate) cement concrete in position to the required line, level and curvature, jointed with cement mortar (1:3), including making joints with or without grooves (thickness of joints except at sharp curve shall not to be more than 5mm), including making drainage opening wherever required, complete all as directed.

M&L for Preparing new or previously untreated Plastered/ Concrete Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

S&F Mild steel plain sheet 1.00 mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed.

M&L for Preparing new or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L for Preparing old treated/painted Steel and Iron Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality) in Camouflage/ Plain pattern, complete all as specified and as directed.

M&L for Preparing old treated/painted(Rusted) Steel and Iron Surfaces of any description, not otherwise described, n exc 10 Cm width or girth and applying Two Coat of Synthetic Enamel Paint (First quality) , complete all as specified and as directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground, complete all as directed by Engineer in Charge.

Desilting/Taking out Brick Bats, Pebbles, Silts, Muds, Clay, etc. from bottom of Drains including Cleaning Grasses, Vegitations, etc., depth upto 2.50 Metre including removing Excavated Materials from the Sides of Drain inluding removing RCC drain cover and refixing after cleanining of drain and removing debris to outside MD/AF Land where directed, complete all as specified and as directed.

M/s Sheoran Brothers Builders And Engineers

shiv shanker enterprises

Ajay Enterprises

M/s Har Nandi Construction Company

DCM ENTERPRISES

VIVEK CONSTRUCTION CO

BS BUILDERS