SPECIAL REPAIR TO BLDG NO P 42 OR MD ACCN SEVEN QTRS IN A BLOCK AT MILIT GIRINAGAR PUNE 411025

Amount

(B/R POTION) :- Complete removal of entire existing water proofing treatment in any position including tarfelt, Plaster, lean concrete of any thickness, gravels etc. and removing the debries out side MD land complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:3 over concrete surfaces mixed with water proofing compound @ 3% by weight of cement in two layers in longitudinal & transverse directions finished even and smooth with using extra cement and applying two coats of roff hyguard ex Rezone chemical or equivalent make treatment by authorised professional applicators complete all as specified and directed. Note: WPC shall be measured and paid for seprately as "Supply Only"

M&L for 10 mm thick rendering in CM 1:4 on concrete surfaces by authorised professional applicators, mixed with water proofing compound @ 3% by weight of cement in two layers in longitudinal & transverse directions finished even and smooth with using extra cement and applying two coats of Roff Hyguard ex Rezone chemicals or equivalent make tratment by authorised professional applicators complete all as specified and as directed. Note: WPC shall be measured and paid for seprately as "Supply Only"

Supply only integral water proofing compound of approved make all as specified and directed.

M & L for cement concrete 1:5:10 type E-2 (using 40 mm graded brick aggregate) as for filling in sunken floor all as specified and directed by Engr-In-Charge.

M&L Acrylic emulsion polymer of acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc as per following procedure :- (a) Surface & surface preparation : Remove all the loose particles , dirt & dust clean by water , wire brush & mechanical cleaning , grease & oil should be cleaned using solvents, If the surface is previously coated with tar, it should be thoroughtly scraped off. The surface should be dry before application. All the cracks and crevices in the concrete slab to be filled with polyurethene based sealent with and including application of PU based primer all as directed by Engr-in-Charge. (b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied ,non toxic,VOC complaint)in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers specification and as dircted by EIC/GE. Make:-Bostic/ Berger / Fosroc / Sika / Asian or any other make approved by E-in-C'sBranch for PU based water proofing treatment.

M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry including dismantling single layer Manglore pattern or similar tiles in roofing and removing unserviceable tiles off the premises & stacking serviceable tiles for reuse complete all as specified and directed.

M&L for Ridges or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 etc complete all as specified and directed.

M&L for 2nd class hardwood, clean sawn, in scantling timber work incl. dismantling of old U/s scantling and removing rubbish off the premises all as specified and directed.

Dismantling battens for tiles, shingle etc. of any size including tilting fillets spaced exc.15 cm complete all as specified and directed.

M&LPlain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads having sectional area exc.13 and not exc.25 Sqcm complete all as specified and directed.

All as per item no.11 here in before but fixing only complete all as specified and directed.

M&L for Eaves/weather boarding with 20mm thick fibre cement board (Non asbestos) and fixed with self drilling and tapping screws of CSK head and joints finished with jointing compound and fibre tape as per manufacturer's instructions complete of approved arch pattern, size, colour and shape including dismantling of old boarding/eaves board fixed in any position complete all as specified and directed. Make:- V-Board (Vishaka Indurstires Ltd) / Everest / Charminar / Ramco as approved.

Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed..

M&L 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with self tapping screws in roofs, walls with grade of zinc coating 275 complete all as specified and directed.

All as per item No. 15.00 here in above but fixing only except sheeting complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coat of creosote oil complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & over 15 mm thick screed bed in CM 1:6 complete all as directed by Engr-in-Charge including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & over 10mm thick screed bed in CM 1:6 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & over 15 mm thick screed bed in CM 1:4 including Dismantling of wall dado / floor tiles Including floor hearth & removal of rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x450x7mm thick on vertical surfaces such as dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match with & over 10 mm thick backing coat in CM 1:4 including Dismantling of wall dado / floor tiles Including floor hearth & removal of rubbish off the premises complete all as specified and directed.

M & L for cement concrete 1:2:4 type B0 (using 12.5 mm graded store aggregate) as in floor (level course) and in similar siruations 25 mm thick all as specified and directed by Engr-In-Charge.

M&L for 18-20 mm thick granite slab (table rubbed and -polished), machine cut, for floors/ shelves, cooking platforms, window cills etc laid over and including 15mm thick CM 1:4 cement screed and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone laid over 20-25mm thick cudappa stone including cutting and polishing edges to be rounded including dismantling of old exisitng stone or flooring of any description & removing rubbish off the premises complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 20 mm graded stone aggregate) as in plinth protection of average 75mm thick complete all as specified and directed.

M & L for complete removal or existing wall treatment and applying three coats of white wash on old / new surfaces including preparation of surface complete all as specified and directed.

M&L for applying two coats of oil bound distemper over a coat of primer on old surfaces of wall including preparation of old surfaces complete complete all as specified and directed.

M&L for applying three coats of white wash on old surfaces of ceiling complete all as specified and directed.

Taking down chowkats or frames of wooden or steel window/ventilator with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but not exc 4 Sqm each and removing from site complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. Note:- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Supply & fix Factory made solid PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C' type GI or 40 x 20 x 19 of MS pipe as stiffner & supplying & fixing in frame at site as per manufacturer's instructions and all as specified and directed.

S&F three track sliding window with 4mm thick tinted glass in two shutter and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing including good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge and including taking down old steel windows complete all as specified and directed. Series of aluminium section as per Jindal is (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352.

S&F anodised powder coated (thickness of powder coating not less than 50 micron) aluminim window and ventilator shutters, fixed type without sash bar, aluminium section weight not less than 0.55 kg/mtr including necessary joining cleats, glazing clips, rubber packing, screws etc. complete all as specified and directed.

M&L for 4mm thick figured glass, pin head type and glazing with not exc 0.5 Sqm in each pane to aluminium frame work for ventilators complete complete all as specified and as directed.

S & F 125 x 60mm size pressed steel frames for doors with one or more rebates incl necessary fixing luges, hinges , lock strike plates etc complete all as specified and directed.

S & F 105 x 60mm size pressed steel frames for doors with one or more rebates incl necessary fixing luges, hinges , lock strike plates etc complete all as specified and directed.

M&L for PCC 1:3:6 type C0 (using 12.5 mm graded stone aggregate) as in door frame filling and similar work filling complete all as specified and directed.

M&L for 35mm thick Flush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed.

M&L for 35mm thick 2nd class H/wood gauged and skeleton shutters, open rebated and prepared to receive gauge etc. (with sash bars) edges of ramming plain, chamfered or grouted, fitted with cut of and mitred beads for securing gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and as directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F mild steel butt hinges 100mm size medium weight, cold rolled fixed with screws/welding to wooded/steel frames or chowkats, complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt 150 mm long of extruded section cast aluminium alloy complete all as specified and directed

S&F Aluminium anodised barrel tower bolt 200 mm long of extruded section cast aluminium alloy complete all as specified and directed

S&F 300 mm long Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed in repairs complete all as specified and as directed

S&F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed in repairs complete all as specified and as directed

S&F Aluminium handles, cast type anodised 200 mm long of extruded section cast aluminium alloy complete all as specified and directed.

M&L for 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for 140mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed.

S & F in repairs 18/19 mm thick, Prelaminatd particle board, ISI marked interior grade, prelaminated on both sides with decorative choice lamination fixed with screws to timber frame work,and with rubber beading at top and front side for doors, partitions in walls in cupboards/kitchen cabinets etc in shelves, partitions and shelves of built-in cupboards, almirah, bookcase, toilet boxes, racks, pemets etc similiar works complete all as specified and directed.

S & F Continuous (piano) hinges 30 mm width of flap (when open),mild steel, brass, bright finish complete all as specified and directed

S&F in repairs 125mm long aluminium anodised Hasp and staple with mild steel hinge pin including bolt to hinge plate and fixed with screws as in cup board shutters complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces over 10cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide on steel surfaces exc. 10 cm width or girth etc. complete all as specified & directed.

S&F in repairs aluminium anodised tubular curtain rail with fixing brackets, stops & rollers all as directed by Engr-in-Charge.

S & F SS chromium plated 6 pin, 45cm to 60cm long hanger fixed to wall with screws complete all as specified & directed by Engr-In-Charge

S&F in repairs stainless steel grating doom 125 mm dia complete all as specified & directed by Engr-In-Charge

Supplying and laying of CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/cieling, 20mm dia with all fittings and complete including taking up or down old unserviceable steel tubing and connections complete all as specified & directed.

All as per item No 57.00 here in before but 15mm complete all as specified & directed.

M & L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified & directed.

S&F 500 ltrs capacity, Rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and in position including ball brass valve 25mm high pressure with polythene float and fly nut complete including dismantling existing water tank and removing from site all as specified and directed.

S&F in repairs Brass chromium plated Tubular towel rail 20mm dia D type, 60cm long between flanges complete all as specified and directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), coloured, with and including plastic water closet seat cover, coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, fixing bolts,,10 ltrs PVC valveless syphonic action type low level flushing cistern with inlet , ball valve, float & handle and flush pipe and connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc complete all as specified and directed.

S&F in repairs bib taps long body cast copper alloy chromium plated ,fancy type with capstan head, screwed down, screwed for CPVC/iron pipe or for brass ferrule 15 mm bore complete all as specified and directed.

S&F in repair fancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed.

S&F in repair angle/stop valves cast copper alloy, screwed down high pressure fancy type chromium plated 15 mm dia with long shank and cup (concealed type) all as directed by Engr-in-Charge

S&F in repairs chromium plated brass shower rose 125 mm dia with swivel joints complete all as specified and directed

Taking down PVC (SWR) pipes of any size / pattern including fittings complete all as specified and directed.

S&F 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring jointed fixed to wall with suitable clampcomplete all as specified and directed.

S&F 75 mm dia PVC(SWR) pipes single socketed in any length with rubber ring jointed fixed to wall suitable clamp complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction, single(single 'T') equal or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction, single(single 'T') equal or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends 75 mm bore complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal 110mm bore complete all as specified & directed.

S&F PVC (SWR) branch piece, single (Single Y) equal or unequal 75mm bore complete all as specified & directed.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal 75mm bore complete all as specified & directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified & directed.

S&F PVC (SWR) vent cowl 75mm bore complete all as specified & directed.

S&F in repairs for 75 mm dia PVC ( SWR) floor trap with grating including jointing with solvant, PCC complete all as specified and directed

S&F PVC (SWR) gully traps 125/100mm setting and jointed in cement solvent complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M&L for 100 mm thick Hardcore (broken stone or boulders) of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick watered and rammed to a true surface complete all as specified and directed by Engr-In-Charge.

M&L for 75 mm thick cement concrete 1:4:8 type B1 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed by Engr-In-Charge.

M&L for 30 mm thick crushed stone sand cushion for laying of inter locking tiles complete all as specified and directed.

M&L for cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in kerbs or copings and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified & directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement & pigment complete all as specified and directed.

E/M PORTION :- Taking down carefully aluminium / copper point wiring complete (light, fan socket & power) including unserviceable fixtures and fittings such as switches ceiling roses pendents regulators sockets light fittings etc complete & removing material for taking credit & making good disturbed wall / floor etc complete all as directed by Engineer-in-Charge

Taking down sub main wiring complete including fitting and fixtures, removing materials for taking credit and the making good the disturbed surfaces of walls, floors, roof etc, all as specified and as directed.

Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs//Isolator etc and disconnecting and making good disturbed surfaces complete all as directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through and including heavy duty PVC caping casing fixed walls / roofs / floors / ceiling etc and 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly including concealed MS box with 3 mm thick laminated sheet cover fixed with brass screws and cup washers for mounting of plate mounting for housing the switches, socket outlets, fan regulators etc complete all as specified and as directed for the following :- (a) One light point controlled by one way switch.

(b) One light point controlled by Two way switch.

(c) One fan/exhaust fan point controlled by one switch and one regulator.

(d) One bell/buzzer point controlled by one bell push button on independent board.

(e) One 3 pin switch socket outlet point 5 Amps on independent board.

(f) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item No. 91.00 above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed.

S & Fix switch piano, flush type single pole, one way 5 Amps capacity complete all as specified and directed.

S & Fix switch piano, flush type single pole, two way 5 Amps capacity complete all as specified and directed.

S&F switch socket combination 2 in 1, 6A flush type complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal complete all as specified and directed.

S & Fix Ceiling rose surface backlite 65x50mm 3 terminals complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as directed.

S & Fix Bell push flush type complete all as specified and directed.

S & Fix call bell (Ding Dong) 240 V, 50 Hz complete all as specified and directed.

S & Fix in repairs batten General purpose industrial compact batten suitable for single in LED Tubelight with integral LED driver, available in single / double side connection CRCA batten suitable for mount LED tube rod 1 x 18 watts including necessary electric connections 3 core 1 sqmm insulated copper wire from ceiling rose to tube light fitting complete all as specifed and directed by Engineer-in-charge.

S & Fix in repairs LED Tubelight (single side connection) with very high efficacy suited for installation in existing tubelight luminaire with G13 lamp holders to give glare free light with necessary fixing arrangement etc complete all as specifed and directed by Engineer-in-charge.

S&F in repairs LED Tube light fitting 10 watt, 2 feet, 230 volts, sleek and polycarbonate batten with an efficient diffuser to illuminate work and retail spaces complete with all accessories all as specified & directed by Engr-in-Charge.

Supply and Fix in repairs wall light, light fixture made up of Polycarbonate, suitable for 9 W LED lamp B22 base including suitable lamp complete all as specified and directed.

S & Fix in repairs 30 Watts LED new generation energy saving and environmental friendly long life LED building light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance complete all as specified and directed.

Taking down the defective ceiling fan / Exhaust fan of any sweep and make after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the ceiling fan by thoroughly cleaning the bearing, shaft, stator, rotor & applying the lubricant / grease to the bearing including applying one coat of painting re-fixing, testing in all respect for smooth running complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Five star rated with brushless direct current motor (BLDC) including dismentalling old unserviceable fan & depositing to the store complete all as specified and directed.

S&F exhaust fan, AC, single phase, 240 V, 200 mm sweep, PVC body with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan for toilets all as specified and as directed

S&F exhaust fan, AC, single phase, 240 V, 230 mm sweep, metal body with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan including making holes in wall and proving louvers with outside additional flaps all as specified and as directed

Supply and fix electric water heater, storage type with heating element of 2 KW capacity 25 litre, BEE 5 Star rated, with temperature control knob and analogue temperature indicator complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including dismentling old unserviceable water heater & depositing to the store all as directed by Engr-in-charge.

S&Fix MCB DB ETPN 4 ways,with metal double door, IP-43 protection suitable for MCCB as incommer and MCB as out going, 415 volt 3 phase complete with appropriate size copper bus bar and neutral link as required at site and including cutting chases to wall for fixing of DB and making good distrubed wall/surface all as required at site i.e directed by Engr-in charge.

S & Fix double door sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door duly flushed in wall suitable for mounting MCBs and making good the disturbed surfaces to match with existing wall finishes including taking down old MCB DB complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN of 40 A to 100 Amps current carrying capacity in the DB complete all as specified and directed.

S & Fix of RCCB single pole and neutral, 240 volts, 30 mA, 40 Ampere, rupturing capacity complete all as specified and directed.

S & Fix of MCB single pole, 240 volts, 6 to 20 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed.

S & Fix sheet metal enclosure distribution board SPN DB's 2 way dully flushed in wall and making good with exisiting wall with SPN MCB complete all as specified and directed.

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC casing and capping with its accessories all as specified and directed by Engr-in -charge for the following :- (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x6.0 sq mm and 1x6 sq mm as earth wire

Taking down the existing electric meter of single phase any capacity after disconnecting electrically and carry out the cleaning and refixing, reconnecting including applying one coat of synthetic enamel paint on existing MS box of electric meter, testing in all respect for smooth running complete all as directed by Engr -in charge.

M & L Earthing complete with galvanised steel earth plate electrode 60x60cmx06mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. Note :- Cost of earth lead and protection pipe upto 7.5 M shall deemed to be included in quoted rate.

M/S P D TUPE

M/S ANJANI ASSOCIATES

Mehta and Co.