Developed as an Eco-tourism destination with adventure tourism activities Bio diversity park and other amenities at Manimutharu Dam in Thirunelveli District

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling GRAVEL in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement five sand ten aggregates) using 40mm gauge HBG jelly inclusive of shoring strutting and baling out water where ever necessary ramming curing etc., complete in respects complying with relevant standard specification and as directed by the Department Officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

For super stucture in Ground Floor

Supplying, fabricating and placing in position TMT Rod/grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Brick work in Cement Mortar 1:5 using best qualityII Class Table Moulded Chamber Burnt Bricks of size 9" x 41/2" x 3" for burnt brick Masonry work including curing, etc., complete complying with standard specifiction.

For Foundation and Basement

For superstructure in Ground Floor

Brick partition walls of 11.50cm thickness using best quality II class table moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)(Hoop iron reinforcement will be measured and paid for separately)11.50cm thickness using best quality First class solid wire cut bricks of size 9" x 4" x 3" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers.

Providing, fabricating and erecting Structural steel members in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 226/2062/800. Cost to include fabricating necessary Gusset Plates, Stiffener plates, Insert Plates, Anchor bolts, Brackets, Bolts, Cleats, seating angles etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1etc. Welding Procedure specifications (WPS) and Third Party mechanical test from NABL accredited lab to be submitted for Owner / PMC/ Architect review. complete as directed by Engineer-in-charge

HELLOW SECTON

MS Grill for Window

Providing and fixing on roof (Ceiling) pressed clay tile (Mangalore Celing tile as inner layer) of 20mm nomial thickness and of approved size and as per approved pattern on steel frame work, including all cost of material, labour lead lift et., complete.

Providing and fixing on roof pressed clay ridge tile (Mangalore tile as outer tile) of 20mm nomial thickness and of approved size and as per approved pattern on steel frame work, including all cost of material, labour lead lift et., complete.

Painting new iron works such as MS flats ,ISMB, Sections and other Steel Works etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of approved colour with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Vertified Anti-Skid Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Engineer in charge before use on works)

Dadooing with printed design colour glazed tiles of size 300 x 450 x 8mm in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in wall, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing Teakwood frame with scantling of required size and design for doors, window frame including labour charges for wrought and putup in possible and for fixing holdfast in frame and necessary etc., complete.

T.W.Door Frame over 2m and beow 3m length

T.W. Door Frame beow 2m length

Supplying and fixing Teakwood Doors shutters fully panelled/Partially Panneled with glass shutters by using Teakwood scantlings upto 4m length and teakwood 40mm thick for styles and rails and 22mm thick for planks and panels including cost of wind appliances and labour charges for fixing the furniture fittings, but Excluding cost of furniture fittings as directed by the Departmental officers in Charge

Polishing the teak wood door with two coats of best French (Lac) polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. (The make, quality and colour of french polish, bees vax should be got approved by the Engineer in charge before use on works.)

Supplying and fixing in position of WPC door shutter made of Single Panel laminated Plastic section of size 200 x 20 mm and WPC extraced shutter frame of size 24 x 60 mm including cost of 3 nos 85 mm butt hinges for single leaf door of size 0.80 x 2.00 m with 2 No aluminium handle and 2 nos 150 x 2 mm aluminium towel bolt hinges etc., complete.

Fabricating, Supplying and fixng in position of steel glazed window (Two Leaves )with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 3mm thick pin headed glass and fixed with 15x12mm teakwood beading of superior quality and fixed with shutter frames.2 numbers of sturdy hinges and one number of handle to be fixed to each shutter at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window.An MS square bar of 12mm size is welded to the inner face of the windowat an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete

Supplying and Fixing in position steel glazed Ventilators with central hung swing shutter using F7D section of size 30x25x3mm for inner outer froames with 4 Nos. Of 12mm dia MS sq.bars for protection and 2 Numbers of clamps welded with outer frame and using 3mm thick pin headed glass for panel including painting with one coat of Red Oxide Primer dismantling the masonry wherever necessary for fixing the ventilator and redoing the same to the original condition fixing the ventilator and redoing the same to the original condition fixing the ventilator in position etc.,

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed by engineer in charge.

Supplying and laying of Interlocking Paver Block 63mm thk. Over a base layer provided with the red soil filling separetly as existing ground leveled properly and ramming with required and than rolling the surfce with light roller make the surface smoothen and light as direction of oficer incharge etc incl. Cost of materials laying and Labour charges complete.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying and laying of Granite Cobble stone flooring of not less than 100 mm x 100mm x 100 mm thk of required colour and pattern over a base layer provided with the red soil filling of existing ground leveled properly and ramming with required and than rolling the surfce with light roller make the surface smoothen and light, watering with sprinkler for compaction properly as direction of oficer incharge etc incl. Cost of materials laying and Labour charges complete.

Architextual tri column at lounge area etc., complete as directed by the departmental Engineer in charge.

Fabrication and supply of MS fabricated Gate for std specification (1.5M X 1.5M Wicket Gate - 2NOS and 5.5M X 2 M Double Swing gate 1nos with paint finishing with standard specification and as directed by the Engineer in charge.

Supplying and Planting of Terminalia arjuna tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation ofrequired size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge

Supplying and Planting of Mimusops elengi tree sapling of height 240 – 300 cm in polythene bag ofsize 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Supplying and Planting of Cassia fistula tree sapling of height 240 – 300 cm in polythene bag of size ncluding loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Supplying and Planting of Saraca indica tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Supplying and Planting of Bauhinia purpurea tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge

Supplying and Planting of Calophyllum inophyllum tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in charge.

Supplying and Planting of Phyllostachys Aurea (Golden Bamboo) tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Planting of Nerium oleander dwarf foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Planting of Jasmine Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Planting of Ixora (Singaporensis) hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge

Planting of Ixora (Coccinea) hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge

Planting of Wedelia trilobata foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in? charge.

Planting of Cynodon dactylon (Arugampul) Grass including necessary soil preparation, transportation, loading and unloading charges etc., as directed by the Engineer in-charge.

Planting of G2 or Shade grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the Engineer in-charge.

Providing and fixing in position Spiral Rota Slide actual equipment size 4.27 X 1.83 X 3.05 m and Children capacity 4 nos necessary section with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position MULTI SEATER MERRY-GO-ROUND actual equipment size 1.5 m Diameter and Children capacity 6 nos necessary section with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position ARC CRAWLING TUNNEL actual equipment size 3.66 X 1.5 X 2.13 m and Children capacity 6 nos and usess for disable children. necessary GIB Class Pipe, LLDPE parts, ISI brand hardwares with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position 2 SEATER ARC SWING RUBBER BELT actual equipment size 3.05 X 1.5 X 3.05 m and Children capacity 2nos and usess for disable children. necessary GIB Class Pipe, ISI brand hardwares with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position MUSICAL POLLS actual equipment size 1.83 X 0.61X 2.44 m and Children capacity 2nos and usess for disable children. necessary SS part,HDPE panles, Graphic strickers, and ISI brand hardwares with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position4 SEATER SPRING SEE-SAW actual equipment size 2.43 X 0.61X 0.91 m and Children capacity 4nos . necessary SS part,GIB class pipe and ISI brand hardwares with PU paint finish complying with standard specification and as diected by the Engineer in charge.

Providing and fixing in position ZIP LINE 250 Mtrs on flat ground. Upto 100 Mtrs Indoors. Upto 200 Mtrs in Motorised version. Upto 50 Mtrs for Kids version with all neccassary Support Structure, Wire, & breaking systems AREA COVERED: 240 - 1500 Sq mtrs

Providing and fixing in position COMPACT ROPE COURSE With upto 10 Elements for an Area of 200 m2 including and Belay Structure, Elements

Providing and fixing in position PRE FABRICATED HUMAN GYRO for a Possible Size of 2 to 3 Persons in an Area of 50m2

Providing and fixing in position ARCHERY COURSE for Approximate area of 300 m2

Providing and fixing in position HUMAN BUNGEE SLING SHOT For 60 feet to 100 feet throw in an Area of 200 m2 including Engineering works, Support Structure and Chords required complete

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Engineer in charge before use on works.

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Above / Below Counter Wash Basin size 550mm x 400mm all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Wash Hand Basin(pedestal washbasins) of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Engineer before use on the work).

Supplying and fixing in position Mirror of size 600x450mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying and fixing C.P. Robe hook fixing with necessary screws etc., complete. fixed on the toilet door complying with standard specification and as directed by the Department officers. The quality and make of coat hook should be got approved by Concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm using rawl plug & brass screws for fixing etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying,installing,testing and commissioning of approved make CONCELD STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 600X600X200 mm tainless steel sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern Engineer before use on work.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Engineer in charge before use on works).

40 mm dia

75 mm dia

110 mm dia

160 mm dia

200 mm dia

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Engineer in charge before use on works ).

110 x 75 mm dia (20 mm water seal)

Supplying & fixing in position 300 X 300 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron double gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Engineer Engineer in charge before use on works ).

Constructing solid block masonry manhole various size of deep in cement mortar 1:3( 1 Cement: 4 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame of size 600x600 mm , PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Engineer Engineer in charge before use on works)

450x450mmx 450mm deep to 750mm deep

600x600mmx 450mm deep to 1000mm deep

900x 900mm x 1000mm deep to 1500mm deep

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Engineer in charge before use on works. Internal & Vertical

15 mm dia

20 mm dia

25 mm dia

Supplying, laying, jointing, testing & Commissioning of UPVC Schedule 80 pressure pipes as per ASTM D 1785 with Sch 80 Fittings as per specifications, jointing with hold tite / super tite & tefflon tape and complete with fittings such as sockets, unions, reducers long or short bends, elbows, nipples flanges,checknuts,etc. Pressure testing of piping and back filling of trench complete as required. The quoted rate shall include necessary earth works, fittings like Tees, Bends, Offsets etc., G.I. brackets with pvc coated GI clamps, nuts & bolts, anchor fasteners, grip bolts, GI threaded, rods, etc., complete for external pipes. (For under ground or above ground external water supply piping.) Vertical & External

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supplying, installing, testing and commissioning of approved make full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tested to a pressure not less than 20 Kg / sqcm with threaded joints complete.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supply ,erection and testing & commisioning of 3HP Submersible pumpset in the capacity of 4000 LPH @ 300Ft, max. total head of 350 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the Engineer in charge.( Sump to OHT transfer pump)

Supply ,erection and testing & commisioning of 1HP Monoblock pumpset in the capacity of max 3 bar Pressure pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the Engineer in charge .( Terrace Booster Pump)

Labour charges for the erection of submersible pumpset in borewell/openwell including fixingand jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the Engineer in charge including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the Engineer in charge including construction of mud pit etc. using only calyx rigs.

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the Engineer in charge ) including construction of mud pit

Drilling of 140/150 mm pilot bore - Upto 60 m Depth ending below ground level

Upto 60 m depth ending below ground level

Upto 60 m depth ending below ground level

150mm dia RS

Labour charges for inserting PVC casing pipes of 150mm dia RS assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Engineer in charge.

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor as directed by Engineer-in-charge and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the Engineer in charge.

Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of PU paint of and total dry film thickness 225 microns. Rate to including all materials, labour charges, scaffolding, stagging, transportation, lead & Lifts, wastage, cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for, and the rate to include preparation of fabrication shop drawings for client's approval. etc., as complete with all respects complying with relevant standard specification, as directed by the Engineer in charge.

Providing the SEATER with best approved quality fine polished Granite Stone Slabs of size 1800 x 500/600 of 18/20mm thick of Jet Black and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complying with standard specifications and as directed by the departmental officers. [The granite stone slabs and other materials to be used shall be got approved by the Engineer concerned before use on work]

Providing Pathway Alround the Gardens, Restrooms, Activity Area, Play area and Outdoor activities

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC Rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper wire for Open PVC conduit Plug point ( 8 points / Coil) Higher End

Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 4 sq.mm copper wire for Open PVC pipe power Plug point ( 8 points / Coil) Higher.

Supply and run of 2 of 1.5 sq.mm. (22/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 14 SWG TC wire with painting of suitable colour.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of single box type 4'18W LED fitting complete on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting etc., complete.

Supply and fixing decorative wall fitting with 15 Watts LED bulb including giving electrical connection etc., complete.

Supply and fixing of 1 feet 9 Watts LED Mirror Fitting including giving electrical connection etc., complete.

Supply and fixing of 15 Watts LED surfcae Mount fitting including giving electrical connection etc., complete.

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Lower end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") including electrical connection etc., complete.

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall including electrical connection etc., complete.

Supply and fixing of 450mm (18") sweep (Heavy duty) AC exhaust fan complete without provision of hole in the wall including electrical connection etc., complete.

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.

Supply, fabrication and installation of 160 Amps FP switch panel made out of 14/16 SWG CRCA sheet steel enclosure, metering & Phase indication lamps welded construction floor mounting type with grey powder coated suitable floor mounting in angle iron frame with comprising of following arrangements etc., complete. Incomer: 160 Amps FP On switch - 1 No Outgoing: 63 Amps TPN Switch - 2 Nos32 Amps TPN Switch - 7 Nos Bus Bar: 500mm x 100mm x 6mm - 3 Nos

Supply, fabrication and instalaltion of 160Amps panel made out of change over switch with 14/16 SWG CRCA sheet steel enclosure suitable to accomodate 160 Amps FPN switch with welded construction wall mounting type with grey powder coated suitable wall mounting in angle iron frame etc., complete.

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle ironframe work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered withhylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meterto fuse units by 19/16 PVC insulated copper wire with earth connection complete

Supply of factory assembled 40 KVA diesel engine Model 3R1040TA G1, three cylinders, liquid cooled, turbocharged with after cooler, developing 102 hp @ 1500 RPM. 3R1040TA G1 is Inline, electric start, compression ignition, 4 stroke, designed to run continuously at 1500 RPM confirming to IS 10002, ISO-3046, BS 5514 standard. Diesel Engine will comply with present CPCB IV+ norms. The diesel engine will comprise of following: Dry type air cleaner, Exhaust Silencer suitable for canopy, Expansion bellow, Lube Oil cooler, Lube oil filter, Fuel Filters, Radiator with pusher type fan and mounting, In-line mono block fuel injection pump, Mechanical governor and fuel feed pump, Flywheel with starter ring and bell housing suitable for close coupling, 12 Volt electric starter motor, Battery charging alternator, Microprocessor based KG934 Controller mounted on the Controller Panel, Protection System for Low lube oil pressure & High water temperature and having dimension of 2758 x 1050 x 1690 (L*W*H) etc., complete.

Supply and Laying of 3 1/2 x 95 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3½ x 95 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3½ x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 4x16 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3½ x 95 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and providing cable end termination of 3½ x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and providing cable end termination of 4 x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 of No.8 SWG copper wire for earth connection.

Providing chemical earthing as per the ISI specification with an earth electrode of 3.0mt class 'B' GI pipe with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 25mm x 6 mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection.

Supply and fixing of NERI Architectural 3Meter HT post top pole 3 Meter Height post top Pole Made of hot dip galvanised mild steel pipe sections 114mm dia. & 76mm dia. Thedecorative pedastal to be provided with a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance. Top Ring-(weight- 3kgs.) is made of cast iron. Entire pole & its parts shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge.the pole should be provided with an inbuilt junction box to fix 32A connector and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic NERI Grey.

SUPPLY OF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 851, Wattage 25W-35W Power Module LED,3000k,UprightLight 851:it's upper square frame in single piece made of die cast aluminum using pressure die-casting process,with a decorative element which is also made of die cast aluminium using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame with Company /brand name engraved in the mold, in single piece, made of die cast aluminum using pressure diecasting process with a four-armed bracket with flange, which is also made of die cast aluminum using pressure diecasting process, fixed at the bottom. Frosted Screen made of polymethylmethacrylate (PMMA) molded in a single piece using Injection molding process. Screen's Impact resistance: IK06. Pure polyester powder coating in Standard Grey Colour. Optical Compartment IP Rating - IP 66. Height – 605mm, Length - 325mm, Width - 325mm,Weight - 5.5Kg, Area Exposed to Wind(S) - 0.15 m2. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/ NICHIA/ OSRAM/ LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit,Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours@Ts 85°C.LM80 report from LED Manufacturer should be submitted.The Light fixture shall be in compliance with IEC 60598-2- 3; IEC 60598-1(Supporting Test Report from UL/UL Authorised/Intertek Laboratory should be submitted) .LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory.Sample should be submitted for approval from concerned engineer-in charge.

Supply and fixing of 1 Meter height 15 watts sloar pillar lamp with pole IP 65 waterproof having 5v/10W monocrystalline soalr panel, 3.7V/4AH Roofer Li-io Battery, power 15 W, 24 Pcs SMD 3030 LEDs, 1200 Lumens, warm white, cool white, white, three optional color modes, Aluminium Alloy material with suitable concerete foundation etc., complete

GST at 18%

VADIVELMURUGAN S K (BID ID -1422227)