Provision of covered waiting area at 4011 FD Hosp under GE East JRC

Amount

Surface dressing in soft/loose soil n exc 15 cm deep complete all as specified and as directed.

Excavation in trenches in soft /loose soil, n. exc. 1.5 m wide and n. exc. 1.5m in depth for foundations etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 sqm on plan and getting out complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavation soil exc 250 but n.exc 500 Mtr & depositing where directed at a level n.exc 1.5 M above the starting point. complete all as specified and directed.

M&L Plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in in foundations,filling and mass concrete, complete all as specified and directed.

M&L for reinforcment cement concrete 1:1.5:3 type A1 nominal mix (using 20mm graded stone aggregates) as in foundations, including raft footing, foundation beams, for columns etc, basement slabs and mass concreete complete all as specified and directed.

Use and waste form work to sides of concrete foundations, footings, bases of columns and similar works rough finished flat surfaces of concrete all as specified.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified.

Description same all as item No 8 above but TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified.

S&F mild steel rolled sections, Framed work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, using FE-290 (Gde-E-165) complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or squareexc 22.5cm but, n exc 30cm long and diametr of neck 16to20mm complete all as specified.

S&F for pre- painted galvatume aluminum zinc coating AZ-150 GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and including Curved/Moulded as per directed, cutting chasing of wall, complete all as specified and directed.

M&L for pre-painted galvatume aluminium zinc cating AZ-150 GI based Plain steel sheet 0.50mm thick of an colour having tensil strenght of 550Mpa as in Roof ridge, fixed with self tapping screws as specified and directed.

Preparationa of new steel surface by scrapping by electrically operated grinder machine/electric regmal machine and M&L for two coats of Sprey Paint over a red oxide primer, width or girth exc 10cm complete all as specified and as directed.

M&L for providing cement concrete1:2:4 type B1 (20mm graded aggregate) as in copings,plinth courses including weathering,slightly rounded or chamfered angles and throating on edges complete all as specified and directed.

M & L for PCC 1:4:8 type D-2, 75mm thick using 40mm graded aggregate as in sub base to floors complete all as specified and directed.

M&L 60 mm thick machine pressed precast concrete rubber molded coloured interlocking paver block and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment complete all as specified and directed.

Supply and laying sand (25 mm thickness ) for cushioning to interlocking paver block complete all as specified and directed.

SARASWATI CONSTRUCTION CO (BID ID -3179506)