SPECIAL REPAIR TO BLDG NO T-27 AND P-1161 AND OTHER SANCTIONED WORKS AT ITARANA UNDER GE ALWAR

Amount

Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removing the domolisd material out side of defence land all as specifed and directed

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering .

Dismantling ballies, hard or soft wood, any position, except in posts and struts; including taking out iron straps, bolts and nuts, etc., if type 3 or any all as per direction by Engr In Charge.

Dismantling of wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/ slabs

Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L brick work with sub class 'B' fly ash bricks , straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

S&F for steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc gde Fe-410 W (Gde E- 250) quality A

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws as specified

M&L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified

S&F for Non asbestos fibre cement building boards 8mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws incl Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including two coats of oil bound distemper over a coat of primer.

M&L for Providing cement concrete as in coping PCC 1:2:4 Type B-0 using 12.5mm graded aggregate, with & including necessary form work Complete all as specified and as directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab n.exc 200mm thick complete all as specified.

M&L form wok to edges of concrete flats, treads, breaks in floors, windows cills, concrete railings, floor and roof n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specifed.

M&L for reinforced cement concrete type B1 (1:2:4) nominal mix using 20 mm graded broken stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specifed and directed.

S&F Mild Steel TMT round bars 10 mm dia and over, cut to length, bent to shape required, including cranking , binding spirally for hooping end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per item No.18 above but 6mm dia to 8 mm dia.

All as per item No.17 above but 5mm dia and over up to & including 10mm dia in stirrups, spacers & binders

M&L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as under floor tiles finished the surface even and fair complete all as specified and as directed.

Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22" x 22" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:6 including rubbing and mirror polishing complete all as specified and as directed.

Material and labour for kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and as directed.

Material and Labour for rubbing and polishing to exiting kota stone flooring including skirting/riser to achive mirror finish all as directed.

M&L for 75mm thick cement concrete (1:3:6) type C1 using 20 mm thick graded stone aggregate as in plinth protection laid in alternate bays n exc 2.5m length finished even & smooth without using extra cement and joint to be filled with Bituminous mastic filling including necessary form work complete all as specified and directed.

M&L for 75mm thick Cement Concrete type D 2 (1:4:8) using 40 MM graded stone aggregate as in sub bases, sub floors etc omplete all as specified and directed

Forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compond Grade 'A' thickness of concrete slab 100mm complete all as specified.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 20 mm thick cement mortar screed in CM 1:6 as in floors complete all as specified and directed.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4..00 Sqm each.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each.

Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm each

S & F 35mm thick, factory made panelled door shutter (two panel), plain, framed with 2nd class hard wood lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS-1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S & F 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F factory made steel windows, box type, any size ((XW2)M/F) double shutter, one openable shutter with glazing bars and other openable shutter without glazing bars, fabricated with members of standard size as shown on drawings including frames complete all as specified. Note :- The quoted rates shall be deemed of lugs and FI required for fixing wire cloth, Sheet Glass, Grills, iron mongry and guard bars as shown on drg and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F Mild steel Framed work using angle Iron ,flat Iron ,round bars as in security doos/gates with end of bars shouldered and or rivetted or forged into spikes ,framed guard bars barred into iron doors ,walkways railing frame work fan hook arrangement as per site requirement and similler work confiming to Fe 290 ,GDE E-165 all as specified and directed.

S&F for Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete.

S&F for butt hinges, cold rolled mild steel , 100mm medium weight and fixed all as directed.

S&F for aluminium anodised barrel tower bolt 150mm long of extruded section all as directed.

S&F for 150 mm extruded aluminium alloy handles , fabricated type, anodised

S&F 200 mm aluminium anodised barrel tower bolts of extruded section

S&F Aluminium alloy, anodised, 300mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F in repair for harrison rails 19/20mm thick, anodised aluminium alloy powder coated with fixing brackets, stops, rollers etc. compete all as specified as directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of stone/brick masonry, or concrete surfaces, finished with even and smooth complete all as specified and directed.

M&L for rendering 15mm thick other than fair faces of stone/brick masonry in cement mortar 1:6 on fair faces of stone masonry or concrete surfaces finished even and smooth without using extra cement all as specified and as directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth, including cutting to edges, all mitres and stopped end, etc complete all as specified and directed.

M&L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed.

M&L two coats of synthetic enamel paint on old steel surfaces of any description over 10cm width or girth including preparation.

Complete removal of existing treatment and preparation of surface of wall, washing,rubbing down and stopping of distempered and painted surface, incl applying two coat wallcare putty 2mm thick for smooth finished of the surface and applying two coat of oil bound distemper all as specified and directed.

M &L for applying two coat of oil bound distemper on decorated surfaces of walls including prepration of wall surfaces, applying two coat wallcare putty 2mm thick for smooth finished of the surface complete all as specified and directed.

M&L preparing new plastered surfaces of walls and applying two coats of cement paint over a coat of water primer complete as specified and directed.

M&L for preparation of old surfaces by washing rubbing down and stopping of plastered surfaces and applying two coats of Cement based paint white or tined on walls including cornices etc complete all as specified and directed.

Surface dressing n exc 15 cm deep in soft/loose soil. Complete all as specified and directed.

Excavation in trenches n.exc. 1.5 M wide and n.exc. 1.5 M in depth for foundation and getting out in soft/loose soil all as specified and directed.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25cm deep as in soft/loose soil copletete all as specified .

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of Anti termite emulsion per square metre of vertical surface all as specified

M&L for treating the top surface of filled earth at the rate of 5 Litres of Anti termite emulsion per square metre of surface all as specified

M&L for treating the soil under plinth protection at the rate of 5 Litres of Anti termite emullsion per square metre of surface area all as specified.

M&L for hard core of broken stone or boulders of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded agg) as in foundation, filling & Mass concrete complete all as specified and directed.

M&L for form work to sides of concrete foundation, footing, bases of columns, plinth beams and similar work, vertical or to batten rough finish flat surfaces on concrete complete all as specified and directed.

M&L for form work to sides and soffit of floor or floor beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs etc also splays between floors and bemss etc rough finish flat surfaces on concrete complete all as specified and directed.

M&L for form work to sides of Pillars, posts, struts piers, columns etc in squarre, rectangular or polygonal, rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work, n.exc 200mm thick flat, rough finished surfaces of cencrete complete all as specified and directed.

M&L form wok to edges of concrete flats, treads, breaks in floors, windows cills, concrete railings, floor and roof n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specifed and directed.

M&L for use and waste of form work to sides and soffits of chajjas for fair finished surfaces complete all as specified and directed.

M&L M-25 RCC using 20mm graded stone aggregate in foundation including footing, plinth beam, base for column, etc complete all as specified and directed.

M&L M-25 RCC using 20mm graded stone aggregate in for beams, cantilevers, bressummers and lintels over 1.5m span complete all as specified and directed.

M&L M-25 RCC using 20mm graded stone aggregate in for columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L M-25 RCC using 20mm graded stone aggregate in for slabs sopported on walls ,beams and columns in floor s ,roofs etc complete all as specified and directed.

M&L M-25 RCC using 20mm graded stone aggregate in for Chajjas etc complete all as specified and as directed

Material and labour for rendering 10mm thick internal surfaces in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement all as specified and as directed.

M&L 15 mm thick rendering in cement mortar 1:4 mixed with water proofing compound finished with even and smooth mixed with Liquid Water Proofing admixture complete all as specified and directed. (Note : WPA shall be measured and paid separately under relevant item of this Schedule).

M & L 5mm thick rendering in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for Screed bed/Roof plastering 20 mm thick in cement mortar 1:4 mixed with Water Proofing Admixture as per manufacture instructions on concrete surfaces of roof slab finishing the surfaces even and smooth complete all as specified . (WPA shall be measured and paid separately)

Supply only Liquid water proofing admixture

M&L for PCC (1:4:8) type D2 (using 40mm graded aggregate) 100mm thick as in Sub base of flooring finished surface even and rough complete all as specified and directed.

S & F 35mm thick, factory made panelled door shutter (two panel), plain, framed with 2nd class hard wood lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS-1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S & F 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a).

S&F 100 mm MS butt hinges medium weight cold rolled mild steel

S&F 150 mm aluminium anodised barrel tower bolts of extruded section

S&F 150 mm extruded aluminium alloy handles , fabricated type, anodised

S&F for aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F for mild steel Helical door spring 300mm duly painted including roller and roller plate complete

S&F for harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. compete all as specified as directed.

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 Kg/Sqm conforming to IS : 3384 and applying a layer of APP based polymeric membrane not less than 3mm thick weighing not less than 3.50 Kg/Sqm, reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) and upper side of membrane thermally insulated with white gravel finish uniformly embedded during manufacturing process. It shall be laid by torch application having side over lap 75 mm and at the end 100 mm, all overlaps and joints shall be sealed by torch application. For parapet, membrane shall be taken to a height of minimum 60 cm and inserted inside the parapet in a groove to a depth of 65 mm. The same shall be finished by a membrane flashing. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M&L Pre-cast cement concrete block masonry 1:2:4 Type B-1 (using 20mm graded stone aggregates) as in kerb stones with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L supply and laying of sand including spreading, levelling and ramming in layers n.exc. 25 cm thick in each layer complete all as directed

S&F for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigment laid over sand cushing complete all as specified & directed. Note :- Sand cushioning will measured and paid seperately.

Material and labour for three coats of white wash on un-decorated surfaces of ceiling including preparation of surfaces complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of 2mm thick wall care putty in two layers on newly plaster surface of walls all as specified and directed.

M&L preparing new plastered surfaces of walls and applying two coats of cement paint over a coat of water primer complete as specified and directed.

Taking down carefully copper/Aluminium point wiring for one light/fan/socket/power point and taking down of teak wood batten / PVC casing caping and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated in existing/New MS sunken box for mounting fittings like switches, sockets, regulators etc with and including new 3mm thick phenolic laminated sheet top cover, complete, all as specified & directed.

All as per item No. 96 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No. 96 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No. 96 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No.96 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fixing decorative ultra slim liner LED lighting fixture with extended poly carbonate environmental friendly, energy efficient suitable for 16W to 20W with LED tube of model E-LITE LED pride and connecting up, complete all as specified and directed.Make : Havells cat part No. LHEXBHP71N1W018 or equivalent of philips/Crompton Greaves/ bajaj/Wipro/GE

S&F LED type street-DRACO SERIES light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete all as directed. Make: C&S Cat Part no. LTESS20WLED or equvalent Crompton Greaves /Wipro

Supply and fixing stepped type electronic fan regulator, flush type and connecting up, ISI marked, 240 Volts.

Supply & fixing Ceiling fan complete with blades, down rods and accessories, 230V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) incl necessary elect connections.

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar,8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral,240 Volt

S & F MCB 6-40 Amp, single pole 240 Volt

S&F sub main wiring on and including passing through PVC conduit pipe 1100 Volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 4 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Casing Caping should measured as one length)

Supply and fixing 2nd class hard wood rectangular block open recessed of size 30cmx25cmx5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos), complete all as specified & directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore.

M/S ROHIT CONSTRUCTION

M/s KUNTAL ASSOCIATES

KARTIK ENTERPRISES

GAR CONSTRUCTIONS

TARKESHWAR DASS CONSTRUCTION COMPANY

Radha Enterprises

M/s S Amarjit Singh

Hitesh Construction