SPL REPAIR TO BUILDING NO. P-69/01-06, P-145/01-06 AND P-114/01-08 AT TAGORE LINE, P-153/01-04 OLD KALINGA LINE UNDER GE JHANSI

Amount

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all Quoins,arches, pillar etc complete all as specified and directed.

M&L for brick work with sub-class B bricks straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) completer all as specified and directed.

M&L for brick work with old size fly ash brick straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) completer all as specified and directed.

M&l for half brick thick wall with old size fly ash brick straight or curved on plan any radius built in CM (1:4) complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in two layers(first coat 10 mm in CM 1:6 & second coat of 5 mm in CM 1:4 ) mixed with WPC as per menufacturers intructions, finished even and smooth without using extra cement complete all as specified and as directed. ( Note: Water proofing compound shall be measured & paid separately) completer all as specified and directed.

Rendering 10 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick on fair faces of concrete surfaces in walls in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed..

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over a coat of primer including 1 mm thick Birla white putty to make the surface to be plain and smooth before primer complete all as specified and directed.

Preparing newly plastered surfaces of new wall and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint (weather proof exterior grade emulsion) of required shade(company Depot tinted) with silicon additives @ 1.43 litre/10Sqm over and including priming coat of exterior primer applied @0.90Litre/10Sqm completer all as specified and directed. Note:- The contractor shall produce batch certificate & delivery challan directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at site along with paint manufacturers drums with seal intact.

Preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Preparing newly plastered surfaces of ceilings and applying three coats of white wash on ceiling complete all as specified and directed.

Complete removal of exisiting treatment, washing rubbing of old treatment and applying three coats of white wash on wall sufaces complete all as specified and as directed.

Complete removal of exisiting treatment, washing rubbing of old treatment and applying three coats of white wash on ceiling complete all as specified and as directed.

Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of oil bound distember over over 1 mm putty and a coat of chalk whitening primer preparatory to distemering complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old surfaces of wall and applying two coat of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint (weather proof exterior grade emulsion) of required shade(company Depot tinted) with silicon additives @ 1.43 litre/10Sqm over and including priming coat of exterior primer applied @0.90Litre/10Sqm complete all as specified and directed. Note:- The contractor shall produce batch certificate & delivery challan directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at site along with paint manufacturers drums with seal intact complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar Complete removal of exisiting treatment, washing rubbing of old treatment and applying three coats of white wash on wall sufaces complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling for Stone slabs and tiles of any description or thickness in floors, aprons etc, laid dry and pointed in any mortar, complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete.all as sppecified and directed.

M&L for Coloured Glazed ceramic tiles 300x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick redering in CM 1:4 on wall complete all as specified and directed.

M&L for jointless double charged/dark shade Virified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but n. exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed.

Ditto all as per item No 23 as above but in skirting including 10mm thick backing coat in CM 1:4 on wall complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 18-20 mm thick and laid over and incl 15 mm thick screed bed in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting / Griding / mirror Polishing on Kota stone as per local trade practice, complete all as specified and directed.

All as per item here-in-above 25 but on vertical surfaces such as skirting/dado over 10mm thick CM rendering in CM 1:4. complete all as specified and directed.

M&L for Granite 15-18mm mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 10 mm thick CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rubbing and polishing complete all as specified and as directed.

M&L for Granite 15-18mm mm thick over including (of any type) work (table rubbed and polished) in shelf partition and like over bracket or groves on walls fixed with Cement including rubbing and polishing complete all as specified and as directed.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 finished even and smooth without using extra cement including forming joints 10 mm wide and upto full depth of PCC and filled with bitumen mastic (1:3) 1 part bitumen 85/25 and 3 parts of sand complete all as specified and directed. {Note:-Bitumen mastic will measured and paid seperately }

M&L for grade A forming construction joint 30 mm deep x 10 mm wide and filled with bitumen mastic all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep getting out in Soft/hard soil omplete all as specified and as directed.

M&L for factory made PU coated, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with over sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion is measured and paid separately.

M&L for sand filling under floor or in foundations incl watering and consolidation, complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and as directed.

Taking down Chowkats or frames Not exceeding 1.5 Sq. M each (Without taking off shutters from the frame) omplete all as specified and as directed.

Taking down shutters of any description exc 1.0 Sqm but not exceeding 2.00 Sqm each omplete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid cuboard & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners incl in this item of required dia and length complete all as specified and as directed.

Ditto all as per item No 37 but of frame of size 65x 100mm complete all as specified and as directed.

Ditto all as per item No 37 but of frame of size 65x 125mm complete all as specified and as directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick prelaminated colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

S&F Factory made single 35 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

M&L 35mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

S &F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelaminated colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 18/19mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F 25 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note:- SS Piano hingr/soft close clip on concealed hinge shall be paid seperatly

M&L for 2mm thick 18 to 25mm wide PVC edge binding tape of approved quality for item No 45 & 46 including necessary sythetic resin hot pressed to edge on binding machine etc complete all as specified and directed.

S&F Window ECO 4000, of double rebate openable/fixed window made of galvanised steel colour coated/powder coated (base steel as per IS 513 Of 'D' quality, galvanised as per IS 277 with zinc of 120 gms/sqm) with total thickness of coating 0.58 microns thick and back coated with alkyd backer 5-7 micron thick or powder coated with pure polyster powder up to 50-60 micron thick. Outer frame section 72 x 55 mm , center mullion section 72 x 50 mm, shutter section 47 x 20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consist rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the section cut to length mitre joined with corner bracket, center millions fixed with mullions cap, stay, handle, latch, 2 nos of heavy duty stainless steel pivot hinges per shutter and paneled with 4 mm thick plain float glass and S. S. mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propyelene Diamine Monomer) gaskets including fixing windows in the Concrete /Masonry wall by means of self expanding screw, including 10 mm square bars welded to 6 x 12 mm flat at a distance 150mm C/C (Pitch) as guard bar etc complete all as specified and as directed.

S&F Box type steel Ventilator with 80x40x 1.25mm RHS frame with side hung shutters (double shutters for glass and gauze) with out sash bars jointed together with and including grills using 12mm square bars @ 10cm C/C Ref TD No CEBZ/TD/14/ 2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and as directed by the Engineer-in-Charge.

M&L for mild steel hold fast and similar small articles conforming to Fe-290 Gde-165, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) for lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, kerb stop rounded or chamfered in edges Etc ccomplete all as specified and directed.

M&L for mild steel framed work section as in door or gates of angle or other section with gusset plates,rails braces etc /windows chowkhats/Shutter frame of steel gate of grade Fe-290 (Gde E-165) including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide complete all as specified and directed.

ditto as per item 53 above but applying one coat of synthetic enamel paint on old steel surface complete all as specified and directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

ditto as per item 55 above but applying one coat of synthetic enamel paint on old wooden surface complete all as specified and directed.

S&F magnetic catcher for fixing in cupboard/cabinet etc to hold the shutter in closed position, complete all as specified and directed.

S&F in repair drawer/shutter handle,projection drop 50 to 65mm on screwed plate for fixing in cupboard, complete all as specified and directed.

S&F in repair door seal for 30 to 35 mm door and fixed complete all as specified and directed.

S&F continuous (paino) hinges,mild steel bright finish in electro galvanised width of flap , when open in 25mm complete all as specified and directed.

S&F of 100mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 75mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed with screws, complete all as specified and directed.

S&F of 150mm long mild steel pressed handles, oval type, stove enamelled black and fixed with screws, complete all as specified and directed.

S&F of 300mm long mild steel, sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 100mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of 100mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed.

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door complete all as specified and directed.

S&F Rubber bush of 25mm long fixed to door complete all as specified and directed.

S&F 125 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm thick sheet glass frosted/figured and pin headed glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L in repair for stainless stell curtain rod 25mm dia with caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed.

M&L in repair for stainless steel curtain rod 15mm dia with wall mounting bracket cutting in to length required at site complete all as specified and directed.

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed.

S&F in repair Aluminium Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

Demolition existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime concrete etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed.

M&L for RCC nominal mix type B-1 (20 mm stone agg) as in beams complete all as specified and directed.

M&L for RCC nominal mix type B-1(20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

ditto all as per item no 86 above but for chajja only complete all as specified and directed.

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Form work to flat soffits of suspended slabs such as roof slabs, floor slabs and lintels, landingand similar work n exc 200mm thick complete all as specified and directed.

Form work to flat chullah hoods, chajjas, troughs and similar items including edges etc. complete all as specified and directed.

Form work to sides and soffits of flat floor or roof beams, beam haunchings, girders,bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed.

Ditto, as per item No 92 above but exc 5cm but not exc. 10cm wide complete all as specified and directed.

M&L for 15mm thick screed bed in CM 1:4 on fair faces of brick work or concrete surfaces mixed with liquid water proofing solution to vertical surface and padding . After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based grout. After the surface is repaired the slab will be tested for water tightness again before proceeding with further treatment. complete all as specified and directed. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solution measured and paid seperate item.

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in sunken floor,padding & levelling course etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as specified and directed. Note:- liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item complete all as directed.

M&L for application/forming of waterproofing liquid membrane moistening the prepared surface for proper dispersion and penetration and applying two component cementitious elastomeric water proofing coating damp block 2k as per manufacturers specifications. The treatment shall be carried out to the entire bottom surface and vertical surface upto the bottom height of wall tiles. Adequate curing to be done on vertical surfaces and ponding test for 48 hours on the bottom surface to be carried out complete all as specified and directed. Make :- M/s Asian paint, M/s fosroc, burger home shield or equivalent NOTE : (a) Treatment shall be done through authorised applicator/representative of the manufacturer only. (b) Warranty for water proofing to be submitted by the contractor as per manufacturer norms complete all as specified and directed.

Supply only integral liquid water proofing compound, mixed in CM as per manufacturer instruction,complete all as specified and directed. (Make : Dr Fixit LW + Professional or equivalent of Fosroc / Sika)

M&L PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion complete all as specified and directed.

M&L 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as specified and directed.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions laid with torch application complete all as specified and directed by Engineer-in-Charge with following course of description below:- (a) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (b) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/Sqm to be applied on prepared surface, till the surface is propely impregnated. (c) After the application of approved bituminous primer, the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (d) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. Note : The cost of all items i.e. from Sr No. (a) to Sr No.(d) are included in quoted rate and no separate payment will be done for the above

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry with gray cement and no pigment in floors, roofs; cut and polished, over and including a layer of 15 mm thick screed bed in CM 1:6 including applying tack coat of industrial bitumen 85/25 @1.2kg/Sqm over stone grit for make grip for laying Screed bed etc complete all as specified and directed.

M&L for apply one coat of aluminium paint @ 0.20 Kg/Sqm over APP membrance for non-accessible roof complete all as specified and directed.

Taking down eaves gutter and rain water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F 110 mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC Nahani/ floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

S&F PVC SWR Gully trap of 125/110 mm outlet, jointing to waste pipe jointing with cement solvent complete all as specified and directed.

Dismantling water tank and removing to store exc. 250 litres & not exc. 500 litres capacity of tanks, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet cnnection, complete all as specified and directed.Make : Sintex /Vectus / Supreme

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing complete all as specified and directed.

M&L for cutting chases,pinning in brick walls for concealed water tubing n.exc 10cm girth and making good facing where required and pointing in CM 1:3 complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

Ditto all as per item no 123 above but fixing only complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

Ditto all as per item no 125 above but fixing only complete all as specified and directed.

S&F in repair Vitreous China counter top oval WHB , white, with rib of size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling, 32 mm PVC Waste pipe 600mm long complete all as specified and directed.

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe complete all as specified and directed. ( Make:- Cera,Parry ware,Hindware.

S & Fin repair for stainless steel kitchen plate rack size 750x 600x230 mm including fixing arrange ment to walls with rawel plug or wooden plugs complete all as specified and directed.

S&F in repair for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste cupling, wastepipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.( Make :- Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality) complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.( Make :- Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality) complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. (Make :-Cera (Ist Quality),Parry ware (super fine), Hindware (Ist Quality).

S & F in repairs 15 mm bore conceald stop cock fancy type,chromium plated with long shank and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed. Make: Hindware/ Cera/ Prayag / Pearl /Parryware.

S&F SS grating of square/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.

S & F in repair Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed. (Make : Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality) .

S&F in repair SS Towel Rail 600mm Long fixed with and including chromium plated brass screws complete all as specified and directed.

S&F in repair of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed. (Make : Prayag/ Hindware/ Parryware/Cera)

S&F of toughned glass corner shelves Shelf of size 300x300 mm fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

M&L for hardcore of broken stone of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15mm thick watered and rammed to a true surface complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) in sub base of flooring / hard standing complete all as specified and directed.

Excavating in trenches not exc 1.5m wide & not exc 1.5m depth for foundation etc or for shafts, wells, cesspits, manholes etcand getting out Hard/dence soil complete all as specified and directed.

M&L for DWCPE (SN8) 200(OD) /175(ID)mm dia pipe laid on PCC beded as per procedure laid down for water test complete all as specified and directed.

M&L concrete bed to drain pipe for 150 mm dia pipes in PCC (1:4:8) type D2 using 40 mm graded stone aggregate incl packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Returning / filling in incl spreading, levelling, watering and well ramming in layers not ext 250mm of Hard/dence soil complete all as specified and directed.

Removing excavated material not exc 50 m and depositing where directed at a level not ext 1.5 m complete all as specified and directed.

M & L cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm internal dia of pipe complete all as specified and directed.

Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs set in cement mortar 1:6 complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling of Framed timber scantling 40sq cm and over in section in any position complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed. (Make : Jindal / Tata / Everest)

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the following points:-

One light point/ceiling fan/exhaust fan controlled by one switch

One Bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per srl item no. 2 here-in-before but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

M&L for submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit ISI Marked conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc incl taking down old submain wiring alongwith conduit complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

All as per srl item no. 4 here-in-before but 2 runs X 2.5 Sqmm + 1 run X 2.5 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

S&F switch piano type, single pole, one way, 6 amps, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F electronic fan regulator socket type in 5 steps, 240V, 50Hz ISI marked with valid CML complete all as specified and directed.

S&F Socket 5 pin, 6 Amp, universal type, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Switch piano type, single pole, one way, 16 amps, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F angle holder, metal cased, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Ceiling rose, three terminals, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Bell Push , flush type, 5 Amp, marked with valid CML complete all as specified and directed

S&F electric bell of DINGDONG type, 240 volts, single pole, marked with valid CML and making all necessary connections, complete all as specified and directed.

S&F Cool/warm white inverter type LED retrofit lamp 07W suitable for pin/threaded type holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix Decorative wall light fixture made up of Polycarbonate and including connecting with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed complete all as specified and directed by Engineer-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50HZ, RPM 1200, Copper winding of sweep 250 mm including connection with 1.5 sqmm, three core copper wire from ceiling rose to exhaust fan upto 1 mtr length including fixing on ventilator complete all as specified and directed by Engr-In-Charge.

S&F LED Tube light fitting batten type 20W, 230W, efficiency 120 Lumens per watt, colour temperature 6500k (Cool White), Power factor grater than 0.9, Polycarbonate body, CRI 80, IP Rating, IP 20, THDv with in 5 % and THDi (8-10%) and integrated Electronic driver complete with al accessories internally Pre-wired and including connecting with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account. (ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase. (iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits.

S&F LED Tube light fitting batten type 10W, 230W, efficiency 120 Lumens per watt, colour temperature 6500k (Cool White), Power factor grater than 0.9, Polycarbonate body, CRI 80, IP Rating, IP 20, THDv with in 5 % and THDi (8-10%) complete with all accessories internally Pre-wired and including connecting Up with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account. (ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase. (iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED building security light fitting 35 watts, Luman efficacy of LED 140 lm/W, PF>0.95 THD<10%, colour temperature 6500K CRI > 7, system luman not less then 2600 lm, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens with toughed glass having bottom separate driver compartment with IP 65 protection and impact resistant of IK 07 etc and all accessories previewed complete including mounting bracket of GI Pipe 40mm inner dia light grade of reqd length and shape including bending, forging or welding etc and suitable bolts and nuts with washers, including connecting with PVC insulated multistandered cooper flexible cable of size 0.5sqmm 3 core form celling rose to fitting al as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account. (ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase. (iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits.

Supply and fix Electric Water Heater storage type, vertical, 25 Ltrs capacity, 5 Star rated, with heating element, PUF insulation, multifunction safety valve, adjustable knob for temperature setting and mild steel inner tank and outer body suitable for operating on 230V, 50 Hz, single phase AC supply including hot & cold water PVC connections and mounting on wall with suitable size & No. of anchor bolts complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 20A rated mini MCB and 20A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge.

S&F of ceiling fans complete with blades, down rods, (with remote) and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value more than 6.00 BEE. Five star rated with brushless direct current motor (BLDC) incl taking down old/us ceiling fan from site and deposited to AGE E/M yard all as specified and directed by Engineer-in-Charge.

Supply and fix of exhaust fan with steel body 300mm sweep with blade , with louvers shutter, voltage 230V, 50HZ, RPM 1200, Copper winding including connection with 1.5 sqmm, three core copper wire from ceiling rose to exhaust fan upto 1 mtr length including fixing on ventilator complete all as specified and directed by Engr-In-Charge.

Supply and fix MCB distribution board, VTPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

S&F of MCB distribution board, TPN, 4 way, 415 V, 3 phase, AC in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Taking down old U/S distribution board alongwith its MCBs and Supply and fix MCB distribution board, SPN, 12 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Note: MCBs shall be measured and paid separately.

All as per item No. 28 here-in-before but SPN, 8 way, 230 V, 1 phase, AC Note: MCBs shall be measured and paid separately.

All as per item No. 28 here-in-before but SPN, 4 way, 230 V, 1 phase, AC Note: MCBs shall be measured and paid separately.

S&F MCCB, Four Pole 63A, with breaking capacity 16 KA, adjustable thermal and fixed magnetic type, ics=100%icu, 415 volt including connection with suitable size aluminium/ copper lugs complete all as specified and directed by Engr-In-Charge.

S&F of MCB 63A, 10 KA, TPN, 415 V, 50 Hz, C series complete all as specified and directed.

S& F MCB SPN 40-63 Amp, 240 V with breaking capacity 10 KA, 'C' series complete all as specified and directed.

S& F MCB SP 6-32 Amp, 240 V with breaking capacity 10 KA, 'C' series complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 25 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT panel based with suitable lugs, glands etc including taking down existing cable of any description complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT panel based with suitable lugs, glands etc including taking down existing cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.

Taking down old U/S earthing and M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

VIJAY BUILDERS (BID ID -3276826)

M/S Kumar Contractors (BID ID -3273215)