PROVISION OF CERTAIN IGLOO SHEDS AND ALLIED BUILDINGS AND SERVICES AT AFS GURGAON

Amount

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

SCH 'A' PART XIV (MISC B/R & E/M ITEMS) Note:- Excavation and earthwork to the extent required for execution of relevant item under this schedule unless otherwise specified shall be measured and paid under relevant items of Schedule 'A' Part-III.

INTERNAL ELECTRIFICATION

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 19 / 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated unsheathed multi-stranded copper conductor cable for flush type metal boxes modular type suitable for fixing modular switches sockets fan regulators etc. with white or any colour cover plate with brass screw cup washer and including PVC insulated unsheathed multi-stranded copper conductor cable of 1.5 sqmm as an earth wire connnected to common earth and earth dolly as per IS specification & as specified for one light/fan controlled by one switch.

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 19 / 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated unsheathed multi-stranded copper conductor cable for flush type metal boxes modular type suitable for fixing modular switches sockets fan regulators etc. with white or any colour cover plate with brass screw cup washer and including PVC insulated unsheathed multi-stranded copper conductor cable of 1.5 sqmm as an earth wire connnected to common earth and earth dolly as per IS specification & as specified for one bell / buzzer point controlled by one push button on the same board with other switches.

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 19 / 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated unsheathed multi-stranded copper conductor cable for flush type metal boxes modular type suitable for fixing modular switches sockets fan regulators etc. with white or any colour cover plate with brass screw cup washer and including PVC insulated unsheathed multi-stranded copper conductor cable of 1.5 sqmm as an earth wire connnected to common earth and earth dolly as per IS specification & as specified for one 3 pin 6 Amps switch socket outlet point on same board.

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 19 / 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated unsheathed multi-stranded copper conductor cable for flush type metal boxes modular type suitable for fixing modular switches sockets fan regulators etc. with white or any colour cover plate with brass screw cup washer and including PVC insulated unsheathed multi-stranded copper conductor cable of 1.5 sqmm as an earth wire connnected to common earth and earth dolly as per IS specification & as specified for one 3 pin 6 Amps switch socket outlet point on independent board.

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 19 / 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit wiring with 4 sqmm FRLS PVC insulated unsheathed multi-stranded copper conductor cable for flush type metal boxes modular type suitable for fixing modular switches sockets fan regulators etc. with white or any colour cover plate with brass screw cup washer and including PVC insulated unsheathed multi-stranded copper conductor cable of 4 sqmm as an earth wire connnected to common earth and earth dolly as per IS specification & as specified for one 3 pin 15 Amps switch socket outlet point on independent board.

NOTE FOR ITEM NO 14.001, 14.002, 14.003, 14.004 & 14.005 :- Modular Metal box, modular cover plate shall be measured & paid separately under relevant item.

Material and labour for point wiring (concealed) in and including rigid non-metallic PVC heavy duty conduit, 20 mm dia/suitable size as per site requirement including cutting chases for conduits sinking for boxes for concealed conduit telephone wiring with 0.4 sqmm, 2 pair of 24 AWG solid copper conductor cable including RJ 11 connector for telephone jacks, flush type metal boxes modular type suitable for fixing modular jacks with white or any colour cover plate with brass screw cup washer complete all as specified and directed.

Supply and fixing modular telephone socket / jack, 1 module complete all as specified and as directed.

Supply and fixing modular metal flush box 8 module complete all as specified and as directed.

Supply and fixing LED luminaire 600mm x 600mm of capacity 36 watt, 240 volt AC surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of size 1.5 Sqmm 3 core complete all as specified and as directed.

Supply and fixing LED luminaire of capacity 1 x 20 watt, 240 volt AC decorative box type with driver, holder including LED tube light including connecting up with driver three core flexible copper conductor cable of size 1.5 Sqmm 3 core complete from ceiling rose complete all as specified and as directed.

Supply and fixing LED luminaire of capacity 1 x 10 watt, 240 volt AC decorative box type with driver, holder including LED tube light including connecting up with driver three core flexible copper conductor cable of size 1.5 Sqmm 3 core complete from ceiling rose complete all as specified and as directed.

Supply and fixing street light LED luminaire of capacity 30 Watt complete with all accessories, including GI pipe bracket 25mm dia upto 1 mtr in length 40 degree bend necessary fixing arrangement on wall nut, bolt, screw, washers and including flexible copper cable from ceiling rose to street light fitting of size 3 core 1.5 sqmm complete all as specified and as directed.

Supply and fixing MCB SPN 6 to 32 Amps breaking capacity 10 KA B curve single phase 240 volts including making connection complete all as specified and as directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as specified, directed and shown in electrical plate No 3 of SSR part-I including testing on completion complete all as specified and as directed.

Material and labour for flameproof point wiring (concealed) in stove enamelled steel conduit not less than 20mm dia/suitable size as per site requirement including cutting cheses for conduits sinking for boxes for concealed conduit wiring with 1.5 sqmm ZHFR insulated unsheathed multi stranded copper conductor cable with metal boxes and cover plate with brass screw cup washer and including ZHFR insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm as an earth wire connected to common earth and earth dolly as per IS specification complete all as specified and as directed for one light/fan point controlled by one flameproof switch.

Material and labour for flameproof point wiring (concealed) in stove enamelled steel conduit not less than 20mm dia/suitable size as per site requirement including cutting cheses for conduits sinking for boxes for concealed conduit wiring with 4 sqmm ZHFR insulated unsheathed multi stranded copper conductor cable with metal boxes and cover plate with brass screw cup washer and including ZHFR insulated unsheathed multi stranded copper conductor cable of 4 sqmm as an earth wire connected to common earth and earth dolly as per IS specification complete all as specified and as directed for flameproof switch socket combined outlet 16 Amps on independent board

Material and labour for flameproof sub main wiring (concealed) complete single core 2 x 1.5 Sqmm ZHFR insulated unsheathed stranded copper conductor cable drawn through in and including stove enamelled steel conduit not less than 20mm dia/suitable size as per site requirement and conduit acessories including single run of 1.5 Sqmm ZHFR insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chases in walls for concealed wiring using machine cutting and making good the disturbed surface complete all as specified and as directed.

Supply, fixing and testing of flameproof cum waterproof LED highbay light fitting of capacity 90 watt, IP 66 protection of cast aluminium alloy material and heat and impact resistance toughen 'A' clear glass having anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor ZHFR insulated cable 1.5 Sqmm complete all as specified and as directed.

Supply, fixing and testing of flameproof cum waterproof LED batten light fitting of twin T8 LED tube of capacity 20 watt, IP 65 protection of cast aluminium alloy material and heat and impact resistance toughen Á' clear glass having anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor ZHFR insulated cable 1.5 Sqmm complete all as specified and as directed.

Supply, fixing and testing of flameproof receptacle with MCB and top plug of 20 Amp DP 250 volts, AC P+N+E complete all as specified and as directed.

Supply, fixing and testing of flameproof receptacle with MCB and top plug of 32 Amp DP 250 volts, AC P+N+E complete all as specified and as directed.

Supply and fixing of flameproof MCB DB SPN 12 way suitable for fixing of MCB's in LM6 or cast iron box of size 355mm x 355mm x 110mm complete all as specified and as directed.

EXTERNAL ELECTRIFICATION

Material & Labour for earthing complete with GI mild steel earth plate electrode 600mm X 600mm X 6 mm thick, burried directly in ground veritcally (Earth pit not less than 2.25 metre deep below ground level) with top edge of the earth plate not less than 1.5 metres below normal ground level, the earth electrode surrounded by adequate quantity of charcoal and salt to a packed thickness of 15 cm on all sides and earth plate connected to GI strip of size 32 x 6 mm by means of bolts, nuts, check nuts and washers of steel and riveted to earth plate at one end and connected to metallic bodies of equipment etc. at other end, earth strip encased in and

including 40mm bore GI light grade pipe with all fitting from top of electrode to the body of equipment fixed with and including 25 x 4mm flat iron clamps, bolts, nuts and washer and also including GI pipe 20 mm medium grade for watering from bottom of earth pit to top of electrode including GI funnel with wire mesh all as shown in electrical plate No. 3 including PCC pit (1:3:6) type C1 in cement concrete 40mm thick precast RCC cover in (1:2:4) type B1 reinforced with 8mm dia TMT bars @ 75 c/c both ways with 01 No lifting handle of 12mm dia MS plain bar, etc. complete all as specified and as directed. NOTE : Quantity of GI strip/ protection pipe beyond 7.5mtrs length shall be measured and paid separately.

Material and labour for straight through cable jointing kit for 1100 V graded cable of cold shrinkable type complete with jointing materials, accessories etc, suitable for XLPE armoured aluminium conductor cable of size 300 sqmm 3.5 core complete all as specified and as directed.

Supply, installing, testing and commissioning of outdoor type step down transformer of capacity 11000/433 volts (at no load), AC, 3 phase 50 Hz capacity 500 KVA ,complete as per Amenment No 1 to IS 1180 :(PART-I ): 2014 , energy efficiency level 3 , core type copper wound, oil immersed, naturally cooled, oil nature, air nature (ONAN) with external cooling tubes, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector symbol DYN – 11 (vector Group) with neutral brought out on secondary side (LV side ) and having tapping at + 5% HV side to - 15% in steps of 2.5 % for variation of HV side and to be changed by means of hand operated

off load tap changer gear. The maximum temperature rise should not exceed 45 degree Celsius when measured by resistance method for transformer winding and 35 degree celsius measured by thermometer for tap oil and 35 degree Celsius in HV/LV winding when measured by resistance method (Necessary test certificate carried out at factory site to be produced) after continuous full load run on an ambient temp of 40 degree Celsius. The transformer shall be comprise of the following :- (a) 3 Nos porcelain bushing with MS cable box sealed for HV side suitable for 11 KV complete with bushing, copper rods, nut and washers, brushing shall confirming to IS-2099 (b) One cable box on LT side (secondary side) consisting of 04 Nos of porcelain bushing shall confirming to IS-7421 with copper rods, complete with nuts and washers with two Nos cable glands suitable for reception / taking out of XLPE insulated heavy duty armoured cable including glands, joint and jointing material complete (c ) Oil conservator with filter type drain valve and oil level gauge. (d) De-hydrating breather with first fills dehydrating agent (silica gel) (e) Explosive vent. (f) Thermometer pocket on tank cover (g) One No 100 mm dia, dial type thermometer, vapour pressure type having range 0-120 degree Celsius with metal guard having maximum perimeter reading temperature indicator with resisting device for transformer (h) Two earthing terminal on tank cover to facilitate fixing of 32 x 6 mm galvanized iron earth strip for earthing of neutral and body. (j) Buchholzs relay for alarming & tripping of circuit breaker. (k) First fill transformer oil as per IS-335-1972, upto desired level.

Supplying, installation, testing & commissioning of HT 11 KV, 3 Phase 50 Hz totally metal clad withdrawable type Vacuum Circuit Breaker panel indoor type with copper bus bar of suitable rating, horizontal isolation type VCB of capacity minimum 630 Amps rated current as per latest IEC 62271- 200. Switch gear panel shall be of sheet steel construction with aluminium zinc not less than 2.5 mm thickness for load bearing section and not less than 2mm thick for non load bearing shall be totally dust and vermin proof. The offered panels shall be type tested to meet IEC 602983& 60694 / IS: 3427 standard , No of operation of Vacuum Interrupter Bottles (ABB/Siemens/Schneider only) for better performance : (i) Mechanical life- 30,000 operations, (ii) Rated Current- 630 A & (iii) Rated short circuit current-18.4 KA .

(A) All the main components like VI/VCB/ Relays/Meters shall be of same make. Approved makes: ABB 9ZNS2)/Siemens (NX-Air)/Schneider (PIX). Panel and VCB parameters are as below (i) Rated voltage level/PF withstand voltage/Insulation level : 12KV/28KV/75KVp. (ii) Continuous current rating : minimum 630A. (iii) Short circuit withstand current : minimum 18.4 KA for 3 Sec. (iv) One No. minimum 630 Apms horizontal draw out type vacuum circuit breaker in 12 KV metal clad floor mounting panel complete with following:- (a) Manually and motor operated ,spring charged type, manually and electrically ( electrical-24 VDC) operation type, incorporating mechanical as well as electrical ON/OFF indication “OFF” push button, test/service position limit switches, with minimum 6 No+ 6 NC breaker auxiliary contacts in service position. (b) Epoxy cast copper wound current transformer (CT), primary insulation level (pf rms / impulse peak )28/75 ka of ratio 100-50/1, 5P10, 2.5 VA burden with metering and protection core including necessary control wiring. (B) Protection arrangement for the breaker shall comprise of the following:- (i) E/F, O/C TCS with IEC 103 protocol for communication & draw out type-numerical type Siemens (7SJ62)/ABB 9REF 615)/Schneider (P-122). (ii) Complete with master trip/Anti pumping relay. All the relay shall belong to common platform and shall be of single make with electromechanical relays in draw out casing.

Material and Labour for Voltage stablizer for automatic operation three phase naturally oil cooled (ONAN) outdoor type & designed for input variation between 300 V to 480 V with out put voltage stablized at 415V with accuracy of ± 1% and speed correction 8 Volts per second and capacity of 250 KVA as per IS 9815/IS 2026. Class `H' insulation with digital temperature/ voltage /current display overload for 100% unbalance etc all as specified and directed including short circuit , high voltage trips protection single phase preventor, low voltage trip auto visual alarm and surge spike suppress and porcelain bushing (conforming to IS 3347) along with cable junction boxes with top or side entry and independent phase contropl etc complete with first fill of transformer oil all as specified and as directed.

Supply,testing and commissioning indoor L.T.Panel board factory fabricated indoor cubicle type totally enclosed made out of 2.00 mm thick sheet metal enclosure with angle iron frame of suitable size, CPRI approved, IP-55 for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel opening doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands of suitable size for cable entry and exit complete with necessary internal wiring with stranded copper conductor FRLS PVC insulated cables of 2.5 sqmm size, duly

painted with one coat of red oxide primer and two coats of synthetic enamel paint of gray or any other approved colour and copper bus bar for three phase 800 amp and neutral of 400 Amp mounted on epoxy insulator-01 Set including connecting the following:- (i) Incoming : LT ACB, 4 Pole of capacity 800 Amps, 50 kA, 415 Volts complete with microprocessor protection for overload and earth fault, inbuilt CT's electrical draw out type- 01 No (ii) MCCB 4P , 36 KA, with thermal -Magnetic release 400 Amp -02 Nos (iii) MCCB 4P, 40 amp , 16 KA,with thermal -Magnetic release of -02 Nos (iv) MCB SPN 16 A, 10 KA-02 Nos (v) MCB TPN 20 amp, 10 KA -1 Nos. (vi) Voltmeter digital type -01 Nos (vii) Ampere meter digital type -01 Nos. (viii) Indicating lamp RYB -03 Nos.

Supply,testing and commissioning indoor L.T.Panel board factory fabricated indoor cubicle type totally enclosed made out of 2.00 mm thick sheet metal enclosure with angle iron frame of suitable size, CPRI approved, IP-55 for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel opening doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands of suitable size for cable entry and exit complete with necessary internal wiring with stranded copper conductor FRLS PVC insulated cables of adequate size, duly

painted with one coat of red oxide primer and two coats of synthetic enamel paint of gray or any other approved colour and copper bus bar for three phase 500 amp and neutral of 250 Amp mounted on epoxy insulator-01 Set including connecting the following:- Incoming :- (i) MCCB 4 P , 36 KA,with thermal -Magnetic release of rating 400 amp -01 Nos Outgoing :- (ii) MCCB 4P, 320 amp , 36 KA, with thermal -Magnetic release -01 Nos (AC plant) (iii) MCCB 200 A, 4P 36 KA (for APFC)-01 Nos (iv) MCCB 40 amp,4P, 16 KA, with thermal -Magnetic release -06 Nos (EOT Cranes, street light). (v) MCB SPN, 16 Amp, 10 KA -05 Nos (Building) (vi) Astro time switch with 3 Pole power contactor , type MNX 9 , - 1 No. (vii) Voltmeter digital type -01 Nos (viii) Ampere meter digital type -01 Nos. (ix) Indicating lamp RYB -03 Nos.

Supply,testing and commissioning indoor L.T.Panel board factory fabricated indoor cubicle type totally enclosed made out of 2.00 mm thick sheet metal enclosure with angle iron frame of suitable size, CPRI approved, IP-55 for operation on 3 phase 4 wire, 440 volts 50 HZ system, with hinged panel opening doors (covers) on two sides with handles, bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands of suitable size for cable entry and exit complete with necessary internal wiring with stranded copper conductor FRLS PVC insulated cables of adequate size, duly

painted with one coat of red oxide primer and two coats of synthetic enamel paint of gray or any other approved colour and copper bus bar for three phase 500 amp and neutral of 250 Amp mounted on epoxy insulator-01 Set including connecting the following:- Incoming :- (i) MCCB 4P , 36 KA rating 400 amps with thermal magnetic release-01 Nos. Outgoing :- (ii) MCCB 4P, 250 amp , 36 KA with thermal magnetic release - 01 Nos (AC plant) (iii) MCCB 200 A, 4P 36 KA with thermal magnetic release (for APFC)-01 Nos (iv) MCCB 40 amp,4P, 16 KA with thermal magnetic release -05 Nos (EOT Cranes, street light). (v) MCB SPN, 16 Amp, 10 KA -05 Nos (Building) (vi) Astro time switch - 1 No with 3 Pole power contactor , type MNX 9 , - 1 No. (vii) Voltmeter digital type -01 Nos (viii) Amp meter digital type -01 Nos. (ix) Indicating lamp RYB -03 Nos.

Supply , install, test and commissioning of LT ACB , 800 A, 4 P , 50 KA , 415 V complete with microprocessor protection for over load and earth faults , inbuilt CTS, electric drawout type, complete with all standard accessories copper bus bar of 800 Amps capacity for incoming and outgoing cable connections etc duly enclosed in CRCA enclosure made of 2 mm thick floor mounted with sufficient space for 3 runs of 300 sqmm 3.5 core UG cable termination on top and botton duly fixed on angle iron frame work of 50 x 50 x 6 mm at a height of 1 mtr from floor level complete including grouting and PCC work complete all as specified and directed.

supply, install, testing and commissioning of Eco friendly Generating Set Diesel Engine driven of capacity 500 KVA/400 KW at 0.8 PF or nearest higher size 415 volts AC, 3 phase, 50 Hz 4 wire, directly coupled alternator and engine, water cooled common base platform with inbuilt fuel tank and including all excavation, PCC foundation, anti vibration pads/dampers as per manufacturer instructions and as directed by manufacturer. The DGset shall work at ambient conditions of Gurgaon and produce specified out put.The derating factors, if any, shall be taken in to consideration while arriving the capacity to give specified out put. The DG set shall be factory assembled by the OEM of the engine manufacturer and all components shall be accommodated in enclosure and other accessories comprising of the following:-

(A) Engine : Eco friendly emmision limits for diesel engines as per CPCB documents vide latest notification GSR105 (E) dated 17 Feb 2015 at Ser No 95 issued by ministry and forest, government of India and noise level (CPCB norms compliances) diesel Engine confirming to BS/IS standard,confirming to BS:5514/DN-6271 / IS 10002/ISO-3046, BHP as per the standard design of OEM to run the DG set in full load / 110% overload with out any change of out put parameters, (not less than 608 BHP),1500 RPM, water cooled complete under NTP condition, with a provision for 10% over load for one hour on 12 hours continuous running with the following:- (i) Radiator/Heat exhanger cooling system (ii) . Corrosion inhibitor coolent (iii) Engine mounted water pump (iv) Thermostats (v) Fly wheel with housing complete. (vi) Fuel pump system with heavy duty injectors and self contained piping. (vii) Spin on type fuel filters (viii) Lub oil pump with self contained piping. (ix) Heavy duty Turbo Charger (x) Air intake manifold with necessary connections. (xi) Dry type replaceable paper element air filter. (xii) Exhaust manifold with flexible piping system and exhaust chimney extended up to a height as per statutory requirement of local pollution control board. (xiii) Residential / Hospital grade silencer. (xiv) Electronic Control panel with Digital governor (xv) Self starter, 24 V, DC (xvi) Display for fault (xvii) Lead acid DC battery 12 volts,180AH - 02 Nos (xviii) Battery charging alternator with inbuilt regulator.

(B) Alternator : Synchronous alternator 500 KVA, 1500 RPM, 415 Volts, 50 Hz, 3 phase system self excited, self regulated, self ventilated in brushless design provided with suitable automatic voltage regulator with ± 1% all load between no load to full load and power factor 0.8 to unity with 10% overload capacity for one hour in any 12 hours of operation without exceeding temp rise limit, Confirming to BS:5000/IS 4722 with standard design with IP 23 protection and class of "H" insulation & having surge separator for protection of alternator for reverse supply .The alternator shall be capable of carrying an unbalanced load of 25% with out injurious heating of any part, provided rated current is not exceeded.The alternator shall withstand a short circuit at its terminals for three seconds with excitation adjusted to develop rated voltage at noload without any damage. (C) Base Frame : Base rail made out of suitable MS channel mounted on AVM pads as recommended by the manufacturer with integral fuel tank of suitable capacity with drain plug, air vent, inlet and outlet connection, level indicator and with provision of cleaning. (D) Acoustic enclosure : Acoustic enclosure drip proof & screen protected meeting stringent MOEF/CPCB norms of 75 dBA @ 1 mtr at 75% load under free field conditions with air inlet louvers powder coated. Use of stainless steel hardware and insulating materials shall meet exacting IS : 8183 insulating materials. Acoustic enclosure shall be as per manufacturer"s design. (E) Provision of DG set foundation : As recommended by the manufacturer in PCC 1:2:4 up to 30cm above ground level.

(F) Generator controller: Microprocessor based generator controller with 4 line LCD display with settable parameters for display, audio visual warning and shut down for the following parameters:- (i) Display parameters :- Battery voltage,Coolent Temperature,Lubricating Oil Pressure, Engine Speed, Engine Hours,Fuel level indication in %,Generator voltage, current, PF, KWH & KW (ii) Audio visual warning for following:- Low oil pressure, High coolant temperature, low battery voltage, low fuel level (iii) shut down/trip with audio/ visual anunciation for the following parameters:- High water Temperature (HWT), Low lube oil pressure (LLOP),Over/under speed,high canopy temperature, under/ over voltage, under/over frequency, low fuel level

(G) AMF panel : Supply, install, testing and commissioning of AMF panel indoor type suitable for 500 KVA DG set, totally enclosed with sheet metal enclosure with sheet (CRCA) duly powder coated, dust & vermin proof made out of min 2.0 mm thick sheet , MS angle iron frame, front door with locking arrangement & two earth points by the side of box, floor mounted cubical type with cable, glands, sockets, etc with provision of cable entry from bottom all prewired and connected complete with comprising the following:- (a) Contactor heavy duty AC3 of capacity 800 Amps , 4 pole , 415 volts with auxilary contacts ( NO+NC) - 2 Nos (b) MCCB 4 Pole of capacity 800 Amps , with adjustable setting , Ics=100% Icu, 800 Amps , 70 KA , 415 volts AC supply - 2 Nos . (c) AMF relay, microprocessor controlled with LCD Display and LEDs for anunciation and settable parameters for sensing/ supervision of rated/ low/high voltage, low/high frequency of mains and generator, over speed, number of generator cranking and cranking period, unbalanced voltage in %, delay time etc with four external fault inputs for HWT, short circuit, over current and earth faults complete.

Material & labour for steel tubular swaged poles , with single swan neck , cast iron base plate , bolts , nuts and screws complete conforming to IS:2713 ( Part I,II & III) 1980 , 9.0 meter long type 410 SP -31 ,errecting truly vertical , welded and reduced section , including painting throughout internally & externally up to standing depth and remaining exterior portion of pole with two coats of aluminium paint over a coat of red oxide primer and numbering of poles complete all as specified and directed . Note:- Earth work , PCC shall be measured & paid separately under relevent items of schedule .

Material & Labour for Street light bracket bend to shape made of 25mm dia medium grade GI pipe 1.5 mtr long fixed on pole or directed. Note:- MS clamp nut bolt etc will be measured and paid separately.

Supply and fixing SMC Junction box pole mounted , 100% weather proof ,fire retardent, complete with side hinged door of size 250 x 200 x 105 mm , made out of engineering plastic including ,3 phase 4 wire aluminium bus bar of capacity 100 amp of required size complete with bus bar insulator fibre/ porcelain and one No single pole MCB SPN 6 Amp, B curve & box fixed on pole with clamps made out from MS flat iron of size 25x5 mm complete with nut & bolts complete all as directed .

Supply & fixing LED street light fitting of capacity 35 watts , working on 240 volts , 50 Hz AC supply with lumen efficacy of LED > 100 LM/W , powered by electronic driver built in potted LED driver (SMPS based constant current supply) with lower THD≤ 10% , PF ≥ 0.95 , output open/short circuit protection , phase to phase protection , over voltage protection , surge voltage protection up to 10 kv with SPD and other safety test as per IS 15885 part-2/sec13, CISPR15 with high efficiency polycarbonate UV stablized cover with integrated lens to ensure Asymmetrical batwing light distribution & housing made out from pressure die-cast aluminium alloy for housing ( heat sink) for effective thermal management sturdiness , excellent corrosion , separate optical and gear compartment with IP 66 protection complete.

Supply and fix flame proof weather proof LED flood light fitting suitable of capacity 120 watt, 230V, 50 Hz AC supply, IP-66 complete all as specified and as directed.

Supply install testing and commissioning of APFC Panel of capacity 100 KVAR Company make Automatic power factor improvement system of 3-phase 415V, 50Hz, floor mounted, modular design structure, Non- compartmentalized, dust and vermin proof, made out of 2.0 mm M.S Sheet and M.S Angle Iron 40 x 40 x 6mm frame, duly powder coated, front & back openable with locking arrangement to facilitate easy maintenance, heavy Cable entry gland provision for hooks on top for mounting panel in Platform. Complete Capacitor and Reactor Filter assembly should be mounted on the rack through nut & bolts so that it can be taken out from the panel, during the maintenance / replacement. Necessary internal connection with proper single core, PVC insulated, multistranded copper wire of adequate size, 650 Volts grade copper wire rating & lugs. Proper control wiring with protection to Relay, fans and Thyristor module comprises of following:-

(k) OUTGOING ( BANK PROTECTION):- (HRC Fuse Link with Fuse Base) (i) Bank - I - 3 nos of 10A HRC Fuse Link in 32A Fuse base (ii) Bank - II - 3 nos of 10 A HRC Fuse Links in 32A Fuse Base (iii) Bank - III - 3 nos of 15A HRC Fuse Links in 32A Fuse Base (iv) Bank - IV – 3 nos of 15 A HRC Fuse Links in 32 A Fuse Base (v) Bank - V –3 nos of 20 A HRC Fuse Links in 32A Fuse Base (vi) Bank – VI –3 nos of 20A HRC Fuse Links in 32 A Fuse Base (vii) Bank – VII – 3 nos of 20 A HRC Fuse Links in 32 A Fuse Base (viii) Bank – VIII –3 nos of 30A HRC Fuse Links in 32 A Fuse Base (ix) Bank – IX –3 nos of 30 A HRC Fuse Links in 32 A Fuse Base (x) Bank – X–3 nos of 50A HRC Fuse Links in 63A Fuse Base (xi) Glass fuse links 2A, with base for Thyrister module Protection (l) THYRISTOR MODULE:– Electronic Thyristor Switching Module( Not SSR- solid state relay) should be capable of Voltage peak withstand capacity of upto 2200 V PIV. They should be installed in separate enclosure with heat sink , firing card and axial fan for its cooling operation (i) Bank - I - 1 no of 5 Kvar (ii) Bank - II - 1 no of 5 Kvar (iii) Bank - III – 1 no of 7.5 Kvar (iv) Bank - IV – 1 no of 7.5 Kvar (v) Bank – V – 1 no of 10 Kvar (vi) Bank –VI – 1 no of 10 Kvar (vii) Bank –VII – 1 no of 10 Kvar (viii) Bank – VIII – 1 no of 15 Kvar (ix) Bank – IX – 1 no of 15 Kvar (x) Bank – X – 1 no of 25Kvar

(m) CAPACITORS: Capacitor should be Super Heavy Duty( MDXL) with 525V, 50Hz capable of withstanding current up to 4xIn and temperature withstanding up to 70 deg C temperature on its surface without any detoriation in its lifespan (i) Bank - I - 1 no of 5 Kvar (ii) Bank - II - 1 no of 5 Kvar (iii) Bank - III – 1 no of 7.5 Kvar (iv) Bank - IV – 1 no of 7.5 Kvar (v) Bank – V – 1 no of 10 Kvar (vi) Bank –VI – 1 no of 10 Kvar (vii) Bank –VII – 1 no of 10 Kvar (viii) Bank – VIII – 1 no of 15 Kvar (ix) Bank – IX – 1 no of 15 Kvar (x) Bank – X – 1 no of 25Kvar (n) Auto/Manual switch -01 Nos.

ROAD / PATH / CULVERT

Material and Labour for providing 100 mm thick Dry Lean Concrete (DLC) Design mix with minimum cement content not less than 150 Kg / Cum of concrete having average strength of each consecutive group of 5 cubes made in accordance with IS-516, not less than 10 MPa at 7 days. The proportioning of the material of Mix should be as per clause 601.3 of MORTH Specifications and as per IRC Specifications complete all as specified and as directed.

Material and Labour for cement concrete work in pavement / hard standing of flexural strength 40 kg/square centimetre in field using 400 kg of cement per cubic metre, compacted thickness of concrete 25 cm or less complete all as specified and as directed.

Material and Labour for forming 12mm thick Expansion joints filled with pre-formed bituminous filler & top 30mm primed & sealed with sealing compound grade 'A' thickness of concrete slab 150mm provided with 20 mm dia MS dowel bars 50 cm long (25 cm in each slab) with ferrules, spaced at 300mm centres, including boring formwork and preformed filler for dowels etc complete all as specified and as directed.

Material and Labour for forming contraction (Dummy) joints 50 mm deep x 10 mm wide, filled with sealing compound grade 'A' quality etc complete all as specified and as directed.

FIRE POINTS & FIRE SYMBOLS

Material and Labour for writting letter or figures (Block, Roman, Italic or Indian) of 90 cm high with fluorescent paint complete all as specified and as directed.

LIGHTNING PROTECTION

Material and Labour for providing chemical earthing complete with copper earth plate 60 cm x 60 cm x 6 mm burried direct in ground earth pit not less than 5 mtr deep below ground level filled with alternate layers of charcoal and salt of 15 cm thickness and top layer of magnesium sulphate 60 cm thick connected to copper earth lead strip 32 x 6 mm by means of bolts, nuts and check nuts and washer incuding earth work final with watering arrangement , wire mesh , GI pipe 50 mm dia for watering and 40 mm dia medium grade for protection of earth lead, PCC pit 1:3:6 type C1 and RCC chamber cover in 1:2:4 type B1 of size 550 x 550mm with 8 mm dia TMT bar of 100mm C/C both ways and testing on completion all as specified and directed.

Material and labour for providing 20 x3mm thick copper earthing strip including porcelain insulator as a separator between wall and strip not an interval of more than 45 cm and fixing screws complete all as specified and as directed.

Supply & fixing single pointed air termination aluminium rod, 12 mm dia 600mm long complete all as specified and as directed.

EXTERNAL WATER SUPPLY

Material and labour for test of pilot bore with electro logging through computerized composite litho log machine at site by ground water consultant and innovative engineer and submitting complete result pertaining to water strata and recommendation to tap water by providing slotted pipe all as required complete all as specified and directed.

Developing and enlarging the pilot boreof 200 mm bore perfectly vertical including maintaining strata samples duly graphically recorded and carried out electronic log test of the layers to the complete depth etc including reaming of 200 mm bore by enlarging to not less than 525mm dia bore suitable for lowering Mild steel casing pipes and gravel packing for the required length complete all as specified and directed. Drilling from ground level upto 60 mtr depth.

All as per item no 14.048 herein before but boring exceeding 60 mtr and upto 200 mtr depth complete all as specified and directed.

NOTE FOR ITEM NO 14.047, 14.048 & 14.049 :- Rates quoted by contractor deemed to be inclusive for the cost of Transportation of drilling machine at site ,consumable stores like fuel , lubricants , bentonite mud and supply of strata chart, borewell assy design ,construction report of borewell and drawing dully signed by contractor & Government authorized agency and other desired information essential for completion of job .

Supplying, assembling, lowering and fixing Mild steel ERW casing pipe 200 mm internal dia, conforming to IS :4270 - 1992 , having wall thickness not less than 8 mm screwed and socketed and welded to each other length of pipe upto 6 mtr long,including necessary fittings & fixtures and jointing from ground level duly painted with two coats of bituminous paint on external surfaces of pipe complete all as specified and directed.

Supplying, assembling, lowering and fixing of 200 mm dia Stainless steel slotted pipes having wall thickness not less than 8 mm, cage type wire wound screen ‘V’ shaped profile in suitable length having slots of size not more than 1mm width including necessary end coupling threaded or welded as directed into bore holes beyond casing pipe complete all as specified and directed.

Material and labour for yield testing of tube well by continuous run with suitable equipment all as per IS-2800 part-II of 1979 including complete testing of water suitable for drinking purpose as per IS-10500 of 1991 from testing Laboratory approved by GE and report shall be submitted to GE. The well shall be tested 24 hours continuous after development of the well to ascertain the yield. The air compressor / higher capacity pump required for the development of the well by means of over pumping shall be arranged by the contractor at his own arrangement.

Material and labour for development of bore wells by means of high velocity jetting together with air compressor having capacity not less than 100 PSI for pumping out mud/ dirty water ,complete all as specified and directed.

Supply & fixing housing clamp for 80 mm dia bore pipe made out of flat MS 100x10 mm thick (length 60 mm) with 4 Nos 20 mm dia of suitable size of bolt, nuts, washers etc including drilling holes of suitable sizes and painting 2 coats of synthetic enamel paints over a coat of red oxide primer all as specified and directed.

Supply and packing pea gravel of size 3 mm to 6 mm duly screened and washed, around casing pipe and slotted pipe in bore hole complete all as specified and directed.

Fabrication & supplying of strata sample box overall size 200x750x100mm, made out 18 to 20 mm thick veneered particle board, frame of aluminium angle of size 25x25x2mm having 20 Nos. partitions of size 1500x100x100mm made with 12mm thick commercial quality plywood and 25x25x2mm aluminium angle bearers, with and also including sliding type sheet glass 5mm thick cover with suitable size aluminium channel frame complete as specified.

Supply and fixing mild steel bail plug assembly 6mm thick suitable for 200mm bore casing pipe internal threaded with strong iron hook, screwed and welded to casing pipe , and handing over the sample strata box complete all as specified and directed.

Supply & fixing housing clamp for 200 mm dia bore pipe made out of flat MS 150x12 mm thick (length 80 mm) with 4 Nos 20 mm dia of suitable size of bolt, nuts, washers etc including drilling holes of suitable sizes and painting 2 coats of synthetic enamel paints over a coat of red oxide primer all as specified and directed.

Supplying & fixing well cap suitable for 200 mm bore well dia consisting of two parts complete with welding and machinery work having provision of cut out for passing of column pipe and fabricated from MS sheet 3.15 mm thick all as specified & directed.

Supply, laying in trenches, jointing and testing 150mm bore centrifugally cast ductile iron pipe with spigot and socket end , pressure pipe class K9 conforming to IS- 8329-2000 with necessary DI fittings including rubber tyton joints including testing complete all as specified and directed.

Supply, laying in trenches, jointing and testing 100mm bore centrifugally cast ductile pressure pipe class K9 conforming to IS- 8329-2000 with necessary DI fittings including rubber tyton joints including testing complete all as specified and directed.

Supply, laying in trenches, jointing and testing 150mm bore centrifugally cast ductile iron pipe with flanged end , pressure pipe class K9 conforming to IS- 8329-2000 with necessary DI fittings including rubber tyton joints including testing complete all as specified and directed.

Note for item 14.061, 14.062 & 14.063 :- (i) Excavation, earth work and DI fittings shall be measured and paid separately under respective items. (ii) Standard length of pipe shall be 5.50 metre or 6.00 metre as available. (iii) The measurement of pipes shall be net as fixed between the fittings including short lengths without any allowance for cutting and wastage and for the portion entering in the sockets of pipes and fittings.

Supply & Fixing CI/DI fittings for flanged/ spigot socketed pipe e.g. bends (any type, radius and angle), tapers any type, (straight, bend, increasing, decreasing or double socket etc) tee pieces, collars, caps and plugs conforming to IS of size upto 200mm bore complete all as specified and directed.

Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 7.5 KW ( 10 HP) coupled with pump135-30 mtr head, discharge 180-390 LPM suitable for 200 mm boring complete all as specified and directed. Note: (i) Discharge case shall be fitted with suitable adaptor of 65 mm nominal bore of 0.6m length threaded at one end and flanged at other end to match with the column pipe duly fitted with 2 Nos. flat iron supports. The adaptor shall be welded to GI pipe outlet and studded with discharge case. (ii) Column pipe and control cable shall be measured and paid separately . (iii) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately. (iv) The work mentioned in the above mentioned item shall be executed after finalization of location and specification of borewell by CGWB.

Supply, installation, commissioning and testing of LT feeder pillar box of size 900x1200x300 mm, outdoor cubical type, floor mounted, vermin proof factory made of CRCA Sheet 3.15 mm thick and MS angle of size 40x40x5mm having suitable legs, both side openable with locking and key arrangement with two Nos pad lock 50 mm, powder coated with three phase, 415 volts, 50 Hz, AC supply all as directed and comprising of the following:- Incoming:- (a) 4 pole MCCB 63A, 10 KA adjustable-01 No. Outgoing:- (a) MCCB 32 Amp, 415 volts, 50 Hz TP, 10 KA - 01 No (b) aluminium Bus bar fixed on epoxy insulators capacity 100 Amp and bakelite insulation sheet at the back with coloured tape-01 set ( 3 phases and neutral).

Supply & fix submersible cable flat 3 core PVC insulated & PVC sheathed, multistranded copper cable of size 16 sqmm, 1100V complete all as specified and as directed.

Material & Labour for earthing with galvanized iron earth plate of size 600x600x6 mm thick buried directly in ground not less than 2.25 mtr below normal ground level, earth plate packed on all side with charcoal mixed with salt to a thickness of 150 mm connected by GI wire 4 mm dia at two points soldered and riveted to earth plate, GI earth strip protected by using 15 mm bore light grade GI pipe, watering pipe GI 20 mm dia medium grade 2.5 mtr long with funnel, wire mesh etc. necessary earth/brick work and PCC work, disposal of surplus soil to a distance not less than 50 metre, chamber of PCC (1:3:6) type C1 using 20 mm graded stone aggregate, coping shall be PCC (1:3:6) type C1 using 20 mm graded stone aggregate

RCC pit cover 50 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate, reinforced with 8 mm MS bar at 80 mm C/C both way & 12mm dia MS round bar handle-1No in lieu of CI pit cover and angle iron frame, funnel wire mesh, testing on completion all as specified and as shown in electrical plate No 3 of MES SSR part-1 2009 complete all specified and as directed. Note:- Quantity of GI strip & protection pipe beyond 7.5mtrs length shall be measured and paid separately.

Material and labour for construction of brick masonry valve chamber of size, 1200mm x 1200mm x 1200mm (internal) suitable for housing sluice valve/gate valve etc with plain cement concrete 1:4:8, type D-2, using 40mm graded stone aggregates for foundation, 100mm thick with 150 mm alround offset from external face of wall, brick work in cement mortor 1:6, 230 mm thick, rendering 15mm thick in cement mortor 1:4, inside complete and outside 150 mm below ground level, coping with plain cement concrete 1:2:4, using 20mm graded stone aggregates, type B-1, including provision of MS sheet cover 3.15 mm thick fixed to MS angle iron frame 40 X 40 X 6 mm embedded in PCC (1:2:4) concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer, including necessary excavation and earth work in any type of soil etc. all as specified and as directed.

Material and labour for construction of brick masonry valve chamber of size, 900mm x 900mm x 900mm (internal) suitable for housing sluice valve/gate valve etc with plain cement concrete 1:4:8, type D-2, using 40mm graded stone aggregates for foundation, 100mm thick with 150 mm alround offset from external face of wall, brick work in cement mortor 1:6, 230 mm thick, rendering 15mm thick in cement mortor 1:4, inside complete and outside 150 mm below ground level, coping with plain cement concrete 1:2:4, using 20mm graded stone aggregates, type B-1, including provision of MS sheet cover 3.15 mm thick fixed to MS angle iron frame 40 X 40 X 6 mm embedded in PCC (1:2:4) concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer, including necessary excavation and earth work in any type of soil etc. all as specified and as directed.

EXTERNAL SEWAGE DISPOSAL

Supply and fixing of LLDPE conventional type septic tank designed to carry sewage and sludge water including excavation in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregates) below foundation, vent shaft, connection etc complete "capacity of LLDPE Conventional type Septic Tank i.e. 05 Users" all as specified and as directed.

Supply and fixing of LLDPE conventional type septic tank designed to carry sewage and sludge water including excavation in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregates) below foundation, vent shaft, connection etc complete "capacity of LLDPE Conventional type Septic Tank i.e. 25 Users" all as specified and as directed.

Material and Labour for construction of soak well 3 metre dia and 6 metre deep in soft soil including PCC foundation 1:3:6 type C2 (using 40 mm graded stone aggregates), Honey comb and solid wall, RCC cover slab etc complete all as specified and as directed.

Material and Labour for construction of soak well 1.2 metre dia and 3 metre deep in soft soil including PCC foundation 1:3:6 type C2 (using 40 mm graded stone aggregates), Honey comb and solid wall, RCC cover slab etc complete all as specified and as directed.

DUNNAGE

Material and Labour for precast vibromatic machine made cement concrete 1:1½:3 Type A-1 (using 20mm graded stone aggregates) as in dunnage of size 1500 mm X 200 mm X 200 mm with plain fair faces including chamfering etc complete all as specified and as directed.

EOT CRANE

Design ,manufacture , Erection , commissioning , trial run and supply of 5 Ton capacity, flame proof, single girder, electricity operated overhead travelling , crane conforming to IS : 807, 3177 & 3938 tested to 25 % overload with a span of 16 to 18 meters , lift 2.9 mtrs and bay length 36 meters and as per the detailed specification as per appended below:- (A) Technical specification of single girder E.O.T. crane:- (a) Type of crane - single Girder EOT crane is of steel box construction in accordance with M5 Duty (class-II) as per IS:3177 & 807 AND 3938 Indoor with continuous Operation . (b) Duty or class of crane -II ( as per IS:3177 & 807 ) Mechanical - M5 (c) Capacity of crane - 5 Ton

(B) Dimensional Details :- (a) Span ( Distance Between centre of Gantry track Rails ) - 18 mtrs ± 100 mm . (b) Height of lift - 2.9 mtrs (c) Site clearance ( Distance from centre of track rail to nearest side obstruction - 200 mm . (d) Bay length - 36.0 mtrs (C) Crane performance - (a) Operating speed ( main) - Speed through VVVFD for all motions . (b) Hoist - 4 mtrs/ min (c) Cross Travel 10mtrs / min (d) Long Travel - 18 mtrs/ min (D) Crane controls - Wireless controls (E) Mechnical Details :- (a) Wire Rope - (i)Manufactured & tested as per ASTM A 1023 M-02 and ASTM A586 (ii) Number of falls - 4 (iii) Wire rope diameter - 12 mm minimum (iv) Construction - 6x36 (v) Tensile strength 180kg/mm2 . (b) Hoist Gear box unit shall be totally Enclosed Helical / spur , gear boxbody made out from MS Fabricated IS: 2062 , gears made out from En-19 as per IS: 1570 , Pinions made out from En-24 as per IS: 1570 , type of lubrication - Oil splash (c) Type of bearings - SA spherical roller / ball bearing (d)Hooks - Type plain 'C' shank as per IS: 3815 , Swiveling on thrust bearing with safety latch complete

(F) Structural Details :- (a) Main bridge Girder made out from fusion welded plate box structure with intermediate stiffeners IS : 2062 (b) End carriage made out from channel and plate IS:2062 (c) Platform - Two number short platform and one number full length walk way platform wide 750 mm with hand railing for maintenance purpose (d) Buffers for CT

Total amount of Schedule 'A' Part XIV carried over to General Summary

Blank

Blank

Blank

Blank

GENERAL SUMMARY

Lumpsum price worked out by the contractor for “BUILDING & STRUCTURE” as listed in Schedule ‘A' Part I representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part I on Srl Page No. 36(R)

Lumpsum price worked out by the contractor for “DEMOLITION AND DISMANTLING” as listed in Schedule ‘A' Part II representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part II on Srl Page No. 38

Lumpsum price worked out by the contractor for “SITE CLEARANCE, EXCAVATION AND EARTH WORK” as listed in Schedule ‘A' Part III representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part III on Srl Page No. 40

Lumpsum price worked out by the contractor for “INTERNAL ELECTRIFICATION” as listed in Schedule ‘A' Part IV above/below the lumpsum price as inserted by MES for Schedule ‘A’ Part IV on Srl Page No. 46(R)

Lumpsum price worked out by the contractor for “INTERNAL WATER SUPPLY” as listed in Schedule ‘A' Part V representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part V on Srl Page No. 48

Lumpsum price worked out by the contractor for “ROAD / PATH / CULVERT" as listed in Schedule ‘A' Part VI representing above/below the lumpsum price inserted by MES for Schedule ‘A’ Part VI on Srl Page No. 52

Lumpsum price worked out by the contractor for “AREA DRAINAGE” as listed in Schedule ‘A' Part VII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VII on Srl Page No. 55

Lumpsum price worked out by the contractor for “EXTERNAL SEWAGE DISPOSAL” as listed in Schedule ‘A' Part VIII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VIII on Srl Page No. 58

Lumpsum price worked out by the contractor for “DUNNAGE” as listed in Schedule ‘A' Part IX representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part IX on Srl Page No. 59

Lumpsum price worked out by the contractor for “FIRE POINTS & FIRE SYMBOLS” as listed in Schedule ‘A' Part X representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part X on Srl Page No. 63

Lumpsum price worked out by the contractor for “EXTERNAL WATER SUPPLY” as listed in Schedule ‘A' Part XI representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part XI on Srl Page No. 66

Lumpsum price worked out by the contractor for “EXTERNAL ELECTRIFICATION” as listed in Schedule ‘A' Part XII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part XII on Srl Page No. 73(R)

Lumpsum price worked out by the contractor for “LIGHTENING PROTECTION” as listed in Schedule ‘A' Part XIII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part XIII on Srl Page No. 75

Total amount of SCHEDULE 'A' PART XIV (MISC B/R & E/M ITEMS) brought forwarded from Serial Page No. 142(R)

Aalaya Engineering Project Private Limited

SARAOGI BUILDERS LIMITED

SHRE GURMUKHDAS CONTRACTOR PVT. LTD.

RAMJI DAS DHAL CONSTRUCTION PVT LTD

NITYA NAND AND SONS CONTRACTORS PVT LTD

M/s Madan Lal Bansal and Co. Contractors Pvt. Ltd.

M M SHAWL Engineers and contractors pvt ltd

Agarwal Jagdish Construction Company Private Limited

Bahl Builders Pvt Ltd

SOOD ASSOCIATES PVT LTD

Ktech Engineer Builders Co. Pvt. Ltd

B D Raizada Projects Pvt Ltd