SPECIAL REPAIR OF JCOs MD ACCN BUILDING NO DD25 (01 TO 08) AT A ZONE AND PROVN OF 02 NOs TOILET BLOCK UNDER GE (WEST) FEROZEPUR CANTT

Amount

Demolition of unreinforced cement concrete in ground floors and paving not exceeding 15 cm thickness below or above ground level complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling course to receive floor finishes, filling of eaves gap, sides of interlocking tiles, filling of pressed steel chowkhats, etc complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6, type C-2 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour over and including a screed layer of 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M&L Non skid coloured ceramic tiles of 7 to 8 mm thick, area of each tile exceeding 0.11 Sq m but not exceeding 0.18 Sqm as in skerting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and including backing with 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

M&L 450mmX 350 & 7mm thick glazed coloured (Digital colour) ceramic tiles on vertical surface of such as skirting, dados and risers to steps etc., including 10mm thick rendering in cement mortar 1:4 on brick or concrete surface finished rough to received dado/ skirting, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade with cement mortar bedding and removing off the premises complete all as specified and directed.

S&F granite( of any type) stone slab of 20mm thick laid over and including15mm thick cement screed bed in cement mortar 1:6 machine cut, size and jointed over grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid bedded and pointed in any mortar complete all as specified and directed.

M&L machine cut kota stone slab flooring 18-20 mm thick over and including 15 mm thick cement screed 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish complete all as specified and directed.

M&L Kota stone slab 18-20 mm thick in skirting, etc over and including 15 mm thick cement screed 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish complete all as specifed and directed.

Taking down chowkhat with shutter exceeding 1.50 Sqm and not exceeding 4 Sqm( without taking off shutter) each complete all as specified and directed.

Taking down chowkat with shutter not exceeding 1.50 Sqm (without taking off shutters) each complete all as specified and directed.

S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S& F Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

M&L framed work such as grills etc with ends of bars shouldered and or riveted or forged into spike; framed guard bars and similar work conforming to Fe 410-0 0r Fe 310-0 complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010) complete all as specified and directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105mmx60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

All as per item no 19 above here-in-before but size 125x60mm with double rebate.

M&L Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in filling of steel chowkhats,bed blocks, coping etc including necessary form work omplete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Makes: Rajshri or equivalent in approved makes.

S&F plain framed panel shutter 30 mm thick second class hard wood (any number of panels ) with panel of timber flat on both side (featherd egde )or veneered particle board medium density wood particle board with commercial face veneers suplied and fitted to chowkhats complete all as specified and directed by engineer in charge complete all as specified and directed.

S&F 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat complete all as specified and directed.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zink primer on steel surfacescomplete all as specified and directed.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F PTMT tower bolts, 200 mm long and fixed with steel screwscomplete all as specified and directed.

S&F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified and directed.

S&F PTMT handle 125mm long fixed with steel screws complete all as specified and directed.

S&F 200mm long aluminium, anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm Extruded aluminium alloy handle complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm each pane complete with oil putty complete all as specified and directed.

&F in repair to 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm incl. incl hacking out old broken glass and putty/beading complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staple etccomplete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F in repairs brass chromium plated bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed. Makes : Prayag, Essco or equivalent in approved makes.

S&F in repairs brass chromium plated long body bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed. Makes : Prayag , Essco or equivalent in approved makes.

S&F in repairs chromium plated cast copper alloy 1-way angle cock with flange suitable for 15mm bore pipe, complete all as specified and as directed. Makes : Prayag, Essco or equivalent in approved makes.

S&F wall mixer with 'L' bend (Provision for OH shower) 15mm for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. Makes :Prayag, Essco or equivalent in approved makes.

S&F in repairs CP brass shower rose 150mm size shower with 300mm arm suitable for 15mm bore pipe complete all as specified and as directed. Makes: Prayag cat No. BS-79S or equivalent in approved makes.

S&F CP soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and as directed.

S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified and directed.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 630mm x 450 mm with integral foot rests including necessary cement concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fcomplete all as specified and directed.

S&F in repairs, Vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified and as directed. Makes : Hindware/Cera- Ist quality or equivalent in approved makes.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F PVC waste pipe of standard pattern, not less than 75cm long, 32/40mm dia for steel sink waste coupling or urinal of suitable size complete all as specified and directed.

S&F galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 15 mm dia including taking up or down old steel tubing complete all as specified and directed.

S&F galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 20 mm dia including taking up or down old steel tubing complete all as specified and directed.

Dismantling brick work built in cement mortar of any specification and in any position complete all as specified.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls, /RCC walls surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified & as directed.

M&L 10 mm thick rendering in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and smooth with out using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1:4 on any face of brick walls or conrete surfaces, surfaces finished even and fair without using extra cement complete all as specified & directred.

M&L Rendering 5mm thick in cement mortar 1:3 on in ceiling, soffits of chajja or similar location any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement etc complete all as specified & directred.

M&L Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer and applying a coat of 1mm thick wall care putty complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkaliresistant priming paint complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying three coats white washing on ceiling surfaces complete all as specified and directed.

M&L white washing one coats on ceiling incl preparation of old plastered surfaces complete all as specified and directed.

M&L complete removal of old existing treatment on walls, cornices etc by brooming down or steel wire brushing scrapping down smoke soot moulds, moss and efflorescence salt and trading oil decorated surface of walls and applying a coat of wall care putty of approved make as on wall surface and two coats of oil based distemper (white or tinted) complete all as specified and directed. Makes :-BERGER, ASIAN PAINT OR NEROLAC.

M&L complete removal of old existing surface and applying two coats cement based paint over one coat of alkali resistant priming paint complete all as specified and directed. Makes :- Snowsem/Durocem/Crimocem.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L Cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in subbase of interlocking 100mm thick complete all as specified and directed.

M&L in repair for precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and pigment laid dry over a layer of 25 mm thick sand cushioning complete all as specified and directed. Note:- sand cushioning to be measured and paid for seperately.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20m graded stone aggregates) as in kerbs, rounded or chamfered on edges complete all as specified and directed.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L 10 mm thick screed bed or bedding layer of mortar in cement mortar 1:4 with water proofing compound @ 0.20 Ltr per bag of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane complete all as specified and directed. Note: WPC shall be measured and paid for separately.

Supply only Liquid water proofing compound.

M&L applying a layer of blown grade of industrial bitumen 85/25 @ 1.20 Kilogram per square metre including preparation of roof surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application including bitumen primer complete all as specified and directed.

S&F 1.00 mm thick stainless steel plate rack of size 750mmx600mmx250 mm all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Demolition of cement concrete in sunken portion any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L 15mm thick cement mortar 1:3 with WPC on walls as well as on sunken floor portion finished even and smooth using extra cement. Note:- WPC shall be measured and paid for separately.

M&L PCC 1:5:10, type E-2 (using 40 mm graded stone aggregate ) as in filling under sunken portion complete all as specified and directed.

M&L 25mm tick PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) as in floor finished even and rough to receive top layer ccomplete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75 mm dia outlet complete all as specified.

S&F ball valves of 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed complete all as specified and directed. Makes: Prayag/ polytuf or equivalent in approved makes.

S&F in repair ball valves of 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed complete all as specified and directed. Makes: Prayag/ polytuf or equivalent in approved makes.

S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed 20 mm dia complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed 15 mm dia complete all as specified and directed.

M&L color rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I capacity of the tank 500 ltrs including GI tank nipple of size 20/15 mm dia including dismantling of old water tank complete all as specified and directed. ( Make - Sintex or equivalent in approved makes.

M&L disconnecting existing 500 ltr capacity tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. And re-fixing in position incl nesesary fittings complete all as specified and directed.

S&F in repair mild steel curtain rod powder coated with fixing side brackets, end cup, rings @10 Nos per running metre and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

M&L Applying one coat of anti-corrosive primer as manufacturers instruction to exposed old and new reinforcement to the full circumference and length of bars to form unbrocken 40 mm micron thick film in the area prepared vide above Srl Item No 102 complete all as specified and directed. Makes :- forsoc (nitozine primer ) sikka or equivalent in approved makes.

M&L applying one coat epoxy bonding agent as manufacturers instruction to old concrete surface in the area prepared vide above Srl Item No 102 in surfaces of columns beams and similar stuctural member including use and waste of water tight form work to facilitate pouring of microfiber complete all as specified and directed.

M&L applying one coat epoxybonding agent as manufacturers instruction to old concrete surface in the area prepared vide above Srl Item No 102 in surfaces of columns beams and similar stuctural member including use and waste of water tight form work to facilitate pouring of microfiber complete all as specified and directed.

M&L hard dwan steel wire fabric cut to length bent to shape required and tying with including mild steel wire annealed not less than 0.9 mm in dia supplied and fixed in reinforcement complete all as specified and directed.

M&L aplication of 20-40 mm thick high build polymer modified to ceiling with cement mortar plaster 1:3 with SWR @4 kg per litre bag of cement applied as per manufacturers instruction complete all as specified and directed.

Demolition of existing RCC chhajja or similar article including cutting of steel reinforcement , making good disturbed portion with concreting or plastering whatever required, mixing with bonding agent (Pedelite/Sika/Fosrock) complete all as specified and directed. Note : Size of Chajja is not more than 2.00 Sqm and of 0.15cm thick.

M&L rolled sections as in main and cross beams/columns, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates.(Fe-410 W Gde E-250 Quality A) complete all as specified and directed.

S&F Pre-painted galvatume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L Cutting chases, pinning in, making good to facings in brick work where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

M&L cutting holes exceeding 400 Sqcm but not exceeding 0.10 Sqm into or through brick walls built in cement mortar all as specified and directed by Engr-in-Charge.

M&L aluminium reflexive paint one coat on top of roof/APP membrane surface scomplete all as specified and directed.

S&F Factory made box type steel window with provision of opening for cooler (size 2'x2.5') including pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S&F Factory made box type steel window with provision of opening for cooler (size 2'x2.5') including pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

Removing excavated material (soil) exceeding 500m buty not exceeding 1.5 Km and depositing where directed complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth for foundation etc or for shafts wells cespits, manholes, pier holes etc not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in layers including leveling watering and well ramming in layers not exceeding 25 cm thick compelte all as specified and directed.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L hard core of brocken bricks of gauge not exceeding 63 mm deposited spread and leveled in layers not exceeding 15 cm thick watered and ramed to a true surface complete all as specified and directed.

M&L 50mm thick PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in flooring complete all as specified and directed.

S&F Vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, complete all as specified and directed.

S&F Urinal flat back vitreous china (White), of size 465mm x 365mm x 265 mm with grating, union for discharge pipe, spreader & 40mm dia PVC waste pipe upto floor trap complete all as specified and directed.

S&F 15mm bore dia fancy type chromium plated Stop valve screwed down, high pressure with crutch or butter fly handlecomplete all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, ’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F Corner glass shelves 300 mm radius, 8mm thick as per sample radius for bath room, fixed on suitable support of brass chromium plated clips complete all as specified and directed.

S&F Towel rail 600mm long of brass chromium plated fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 170 gm) complete all as specified and directed.

S&F 20mm bore dia Gun-metal,globe or gate valve Gate valve screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified.

S&F 15mm bore dia Gun-metal,globe or gate valve screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified and directed.

S&F 75mm bore dia PVC (SWR), floor trap, Plain with grating including jointing with solvent cement complete all as specified and directed.

M&L cement concrete 1:3:6, type C2 (with using 40 mm graded stone aggregate) as in concrete bed to drain pipe 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested completed all as specified and directed

S&F salt glazed stonewire drain pipe 150 mm internal diameter grade A laid in trenches jointed and tested complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains 150mm dia,making good to pipe & rendering,cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required complete all as specified and directed.

M&L preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primercomplete all as specified and directed.

Use & waste of formwork to sides of concrete foundations,footings,bases or column,raft and raft beams,sides and soffits if any of foundations and plinth beams and similar work,vertical or batter etc rough finished surface of concrete complete all as specified and directed.

Use & waste of formwork to sides of pillars,posts,struts,piers,columns and stanchions ect fair finished surfaces of concrete complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilever, shelves including supports, overhangs, etc also splays between floors and beams etc rough finished surfaces of concrete all as specified and directed.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Use & waste of formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but not exceeding 20 cm wide complete all as specified and directed.

M&L RCC 1:1.5:3, type B1 (using 20mm graded stone aggregate) as in foundations including rafts,footings,foundations beams, bases of column etc complete all as specified and directed.

M&L RCC 1:1.5:3, type B1 (using 20mm graded stone aggregate) as in columns,pillers, piers,posts and structs etc complete all as specified and directed.

M&L RCC 1:1.5:3, type B1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L RCC 1:1.5:3, type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per Srl Item No 144 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups spaces and binders complete all as specified and directed.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 2 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked.

Supply & fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked complete all as specified and directed.

Supply & Fixing bell push flush type 5 Amps duly ISI marked complete all as specified and directed.

Supply & Fixing ceiling rose, PVC/Polycarbonate, isolated three terminals complete all as specified and directed.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulbcomplete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply & Fixing in repair stepped type electronic fan regulater flush type on the existing phenolic laminated sheet etc. as reqd complete all as specifed and directed.

Supply & Fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply & Fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply & Fixing LED tube light fitting 1X18 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Makes:- Cat Part No LHEXBLP7UN1W018 of make "Havells" or techno-commercially equivalent in approved makes.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 4 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply & Fixing in repair MCB single pole (SP) 240 volts, 40 Amps, 10 KA 'B' Series complete all as specified. Note : 40 Amps 'B' series SP use for TPN DB outgoing purpose.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series complete all as specified and directed.

Supply & Fixing single pole neutral (SPN) 32 AMP rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply & Fixing Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete all as specified and directed.

Supply & Fixing in repair sub main wiring of 4 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia all as specified and directed. Note: Two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length.

M&L sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and directed. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run.

M&L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm & 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) complete all as specified and directed.

Supply & Fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, two single core cables flat or circular of stranded conductor of 10.0 Sqmm complete all as specified and directed.

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 Core complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling, including spreading, levelling, watering and well ramming in layrs not exceeding 25cmin soft/loose soil complete all as specified and as directed.

Removing surplus soil to a distance not exceeding 50m and dpositing where directed at a level not exceeding. 1.5m above the starting point complete all as specified and as directed.

M&L sand filling under floors, foundation or cable protection including spreding leveling in layer not exceeding 25cm thick complete all as specified and directed.

M&L Bricks common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise acrose the line of cable in trenches for protection of undergroud cable complete all as specified and directed.

S&F Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required complete all as specified and directed.

S&F Galvanised iron steel tubing 25 mm (1.0") bore ISI marked medium grade with all fittings (ISI marked) duly laid in trenches complete all as specified and directed.

S&F Galvanised iron steel tubing 20 mm (3/4") bore ISI marked medium grade with all fittings (ISI marked) duly laid in trenches complete all as specified.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 40 mm dia and fixed complete all as specified and directed.

Cutting existing CI/GI pipe 40/50/80/100 mm bore including run lead joints of suitable size with necessary fittings complete.

JAWAHAR CONSTRUCTION COMPANY (BID ID -3498445)

ABHISHEK AND COMPANY (BID ID -3498715)

M/S Pee Kay Builders (BID ID -3498476)

Bhupindra Traders (BID ID -3498570)

M/S N Maini Constrution (BID ID -3498705)

RAKESH KUMAR SATISH KUMAR (BID ID -3498771)

M/s Sarup Singh (BID ID -3498786)