GE/CHM-92/2023-2024 SPECIAL REPAIR TO TOILET, BATHROOM OF BLDG NO P 52, PARKING SHED AND CONSTRUCTION OF TOILET ,BATHROOM AND URINAL POINT UNDER GE CHANDIMANDIR

Amount

Taking down chowkats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. includidng a shop coat of red oxide, fill of PCC 1:3:6, complete all as specified and directed.

Factory made flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and drawing on Page No. 160 of SSR-2010 (Part II) all as directed by Engineer-in-Charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing mentioned on Srl Page No. 134, 135 and 146 of SSR Part-II including aluminum iron mongery.

Demolition of cement concrete (reinforced) of any description and in any position, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position, complete all as specified and directed.

Plain cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection, 75mm thick, laid to slope of 1:20, finished even and smooth, with 10mm wide joints to full depth @ 2.5m c/c and at corners, filled with mastic mortar, including dismantling of PCC of complete all as specified and directed.

Reinforced cement concrete 1:2:4 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in beams, cantilevers , bressumers,lintels over 1.5m span, all as specified and directed .

TMT bars for reinforcement, 10mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

All as per serial item No 11 herein before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, -ditto-

Form work to sides and soffits of floor or roof beams, beam hanunchings, girders, shelves including supports, overhangs etc also splays between floors and beams etc rough finished surface of concrete flat complete all as specified and directed.

Demolition of brick work, stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles all as specified & directed by Engineer-in-charge.

Brick work with sub class ‘B’ bricks , old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 , complete all as specified & directed.

Brick work with sub class ‘B’ bricks , old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 , complete all as specified & directed.

Material and Labour Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed

Glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick / stone walls or ceiling including raking out joints, hacking for key, scrubbing down with water, etc , complete all as specified and directed.

10mm thick rendering in Cement and Sand mortar 1:6 over concrete /brick surfaces finished even and smooth without using extra cement, complete all as specified & directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, inclunding using water proofing compound complete all as specified. Note : WPC shall be measured and paid separately.

5mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement complete all as specified and directed

25mm thick PCC 1:2:4(using 12.5mm, type B-0 graded stone aggregate) Damp proof course to horizontal or vertical surfaces including necessary formwork complete, all as specified and directed.

Supply only Integral waterproofing compound, all as specified.

Two coats of white wash on old decorated ceiling surfaces including preparation of old surfaces complete all as specified and directed

Two coats of white wash on old decorated ceiling surfaces including preparation of old surfaces complete all as specified and directed

Three coats of white wash on wall surfaces including preparation of new plastered surfaces complete all as specified and directed

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint of approved tint, complete all as specified and directed.

Preparation of old surfaces of walls and applying two coats of cement base paint of approved tint, including necessary scafolding and safety arrangements, upto three storey bldg complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer, complete all as specified & directed by Engineer-in-charge.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide, complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specifiecation & drawing complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore ,complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth complete all as specified and directed .

Vitreous china Wash hand basin,under the counter, white, of size 560X450mm, fixed as in repair complete all as specified and directed.

Vitreous china, wash down water closet pan, superior white, Pedestal pattern WC with ‘P’ or ‘S’ trap, seat cover (excluding, flushing cistern and flush pipe), complete all as specified and directed.

Supply and fix wash hand basin, vitreous china, flat back , white of size 550X400mm, MS angle bracket of suitable length and size embeded in wall with PCC 1:2:4 complete all as specified and directed.

Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, set with cement concrete, fixed as in repair, complete all as specified & directed.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc as in repair complete all as specified.

Framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165, as in repair complete all as specified & directed by Engineer-in-charge.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; chains; hand made sliding bolts; clamps; hold fasts; wall ties; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles confirming to Fe-410-O or Fe-310-O complete all as specified.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed.

Plain cement concrete 1:7:12 type F-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete complete all as specified & directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed with solvent laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed with solvent laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repair complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repair complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

75mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware etc) internal dia of pipe 200mm. Set in cement mortar including PCC packing in bed and hunching complete all as specified and directed (excavation and earth work shall be measured and paid separately).

RCC pipes class NP2 200mm dia bore, with collars, ISI marked, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed

Salt glazed stoneware drain pipe grade ‘A’ 150mm bore, ISI marked, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed.

Plain cement concrete type C-2, 1:3:6 using 40mm graded crushed stone aggregate as in bed to drain pipes including cradle of 200mm bore pipe after the pipes are laid and tested , complete all as specified and directed.

Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples , fixed as in repair complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden, metel frames including punching or drilling out glazing pins/spring clips complete all as specified and directed.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

3mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

2000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered hoisted and fixed in position, including tank nipple, PTMT float valve of 20 mm bore etc, fixed as in repairs complete all as specified and directed.

500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered hoisted and fixed in position, including tank nipple, PTMT float valve of 20 mm bore etc, complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning works etc and hoisting if required reconnecting and refixing in position of capacity exc 500 ltrs but n.exc 1000 ltrs, complete all as specified & directed.

Bib taps brass, fancy type, with wall flange, chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, complete all as specified and directed.

Bib taps brass, fancy type, with wall flange, chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed in repair complete all as specified and directed.

15mm bore pillar tap, long body with quarter turn, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

15mm bore pillar tap, long body with quarter turn, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, fixed as in repair, complete all as specified and directed.

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, fixed as in repairs, complete all as specified and directed

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fcomplete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve (concealed type), chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Stop valve (concealed type), chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

200mm aluminum anodized barrel tower bolts of extruded section, complete all as specified.

150mm aluminum anodized barrel tower bolts of extruded section, complete all as specified.

150mm size aluminium handle (ISI Marked), cast type, anodised complete all as specified & directed

100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

75mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

Aluminium alloy, anodized, sliding door bolts with hasp staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium, 300 mm long and dia of rod not less than 16 mm, ISI marked, complete all as specified.

Floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), complete all as specified and directed.

Brass, chromium plated, tubular towel rail 20 mm dia. ‘D’ type, 60 cm long between flanges including brackets, complete all as specified and directed.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed.

CI floor trap 100mm dia with CP grating including jointing to waste pipe in cement mortar 1:2:4 complete and making good the disturbed surface to match the existing surface, complete all as specified and directed

100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement in repair complete all as specified & directed

Vitreous China Urinal, Half stall type, white and including flushing cistern, flush pipe and waste pipe, fixed as in repair complete all as specified & directed

Hand jet chromium plated (health faucet ABS Body with 01 m PVC pipe & wall hook) for 15mm bore with fittings, fixed as in repairs complete all as specified and directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, complete all as specified & directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, fixed in repair complete all as specified & directed.

15mm dia PVC connection with PTMT nut, of length 450mm, complete all as specified and directed.

15mm dia PVC connection with PTMT nut, of length 450mm, fixed as in repairs complete all as specified and directed.

32mm dia waste coupling / waste fitting of PTMT any colour high-pressure screwed for iron pipe and fixed (minimum weight 45 gms), complete all as specified and directed.

32mm dia waste coupling / waste fitting of PTMT any colour high-pressure screwed for iron pipe and fixed (minimum weight 45 gms), fixed as in repair complete all as specified and directed.

Soap dish, any type, fixed to plugs with chromium plated brass screws fixed as in repair complete all as specified and directed.

Vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Central hole Basin Mixer, with popup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Granite stone slabs, 16 to 18mm thick, width and length as per site requirement, best quality machine cut and polished to be fixed in floors,cooking plateform, tread, raiser of steps and vertical surfaces etc and jointed with gray cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, rubbing, cutting / rounding of edges and corners where required with and including 15 mm thick screed bed in cement mortar 1:4, Complete all as specified and directed.

Steel rolling shutters (1 mm thickness of lath) without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, push, pull or manual type fixed as in repair complete all as specified and directed

Kota Stone Slab flooring, 20-25mm thick, best quality for staircase landing , treads steps, etc laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm screed layer in cement mortar 1:4, cutting, rubbing, grinding and polishing upto granite finish, complete all as specified.

All as per serial item No 110 herein before but in skirting, riser of staircases etc over and including 10mm thick rendering in cement mortar 1:4

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar, including removal of rubbish from site complete all as specified & directed.

Demolition of mud phuska as in roof of any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof) complete all as specified & directed.

PCC 1:3:6 type C-1 (20 mm graded stone aggs) as in roof padding, roof kerbs rounded or chamfered on edges complete all as specified and directed.

Rendering 15mm thick (average thickness) plaster in cement mortar 1:4 mixed with WPC on concrete roof surfaces including flashings and junction of parapets etc , finishing the surface even and fair without using extra cement all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid separately as supply only).

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, over primer coat bonding material of blown bitumen 85/25 grade heated to working temperature of 180° C applied @1.2Kg/Sqm. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying two coats of bituminous aluminium paint @100gm/sqm on top of membrane, including dismantling of existing felt /treatment, complete all as specified & directed.complete all as specified & directed.

40mm thick brick tiles with including 20mm thick cement mortar 1:4 jointed grouted and pointed complete mixed with crude oil 5% by weight of cement complete all as specified and directed.

All as per serial item No 117 herein before but except tiles –ditto-

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft and loose soil all as specified & directed by Engineer-in-Charge.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation , mass concrete complete all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removal excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed.

Reinforced cement concrete type A-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in beams, lintels over 1.5 metre span and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Reinforced cement concrete type A-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Reinforced cement concrete type A-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in chajja and the like, complete all as specified and directed (reinforcement shall be measured and paid for separately).

Form work to soffits of suspended slabs such as roof slabs, beams, balconies, roofs, canopies shelves , chajja, lintel rough finished surface of concrete flat not exc 200mm thick complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam hanunchings, girders, shelves including supports, overhangs etc also splays between floors and beams etc rough finished surface of concrete flat complete all as specified and directed.

Form work to chullah hoods, chajjas and similar items including edges / sides and soffits of lintels etcrough finished surface of concrete flat complete all as specified and directed.

Spreading and levelling of earth in layers n exc. 25 cm thick and well ramming including watering as required complete all as specified and directed.

Hard core of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in flooring etc, complete all as specified and directed.

Factory made box type steel ventilators, openable with top hung shutters with box type hinges including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded, complete all as specified and directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Square Metre in each pane, complete all as specified and directed.

Material and labour plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, hold fast, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed by Engineer-in-charge. - (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in plain cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required, internal dia of pipe 200mm all as specified and directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 t complete all as specified & directed by Engineer-in-Charge

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, including dismantling of old sheets complete all as specified and directed.

Coloured non skid porcelain tiles exterior grade 300x300x9-10mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed by Engineer-in-charge.

Poly carbonate coloured sheets as approved, 6mm thick as in roofs as in dome shape, circular / semi circular / arch type shape, including self tapping screws / form work / scafolding if required at site to complete the work including adequate size steel screws, washers, nuts, rubber strips/ rubber beading, silicon etc to fill up exisig holes etc aluminium strip/ flat etc as per manufacturer’s instructions, complete all as specified and directed.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete all as specified and directed.

Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed.

All as per serial item 143 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 143 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose combined two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate 3 terminal type with backplate type with back plate with LED bulb B-22 suitble for batten fitting, complete all as specified and directed.

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 12 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 4 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB, SPN, 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size , fixed as in repair complete all as specified and directed.

LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note :- (i) For the purpose of measurement, 2 single core of 4 sqmm and one single core earth cable of 4 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

20 to 25 mm dia, rigid non metallic PVC concealed conduit, 'ISI marked', inclusive of all fittings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing accessories such as couplers lock nuts, saddless, pipe hooks etc for wiring, fixed as in repair Complete all as specified and directed .

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

LED secuirty light 35 watt LED with lens and water/ weather proof powder coated high pressure dia cast housing with IP-66 built- in control driver, aluminium reflector, heat resistant toughened clear glass, connector block, surge protection with 20 watt LED lamp fixed on ceiling/pole/wall/ with fixing arrangement fixed with nuts bolts and 1.5 sqmm 3 core flexible wire from ceiling rose to light fitting , as in repair complete all as specified and directed .

Exhaust fan, steel body AC single Phase. 230V of size 380m sweep, heavy duty with, blades, and frame and louvers, complete all as specified and directed.

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Premier Constructions

Gunjan and Gunjan Associates

M/s Om parkash

Standard Const. Co.