SPECIAL REPAIR TO BUILDING NO T-33 SINGLE OFFICER, P-50 BATHROOM BLOCK AND CERTAIN OTHER SANCTIONED REVENUE WORKS AT KREUH UNDER GE 861 EWS.

Amount

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed

Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed

Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each, and removing from site, complete all as specified and directed

Demolition of cement concrete (reinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed

M&L Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:6 complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preapration of new plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

Preapration of new plastered or unplastered surfaces of wall to receive 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

S&F in repair viterious china wash down water closet pan (pedestal pattern), coloured (excluding fixing bolts, flushing cistern & flush pipe) & including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. and including plastic water closet seat black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinges device & making good to dismantled/damaged floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, coloured, round shape, of size 550mmx400mm including brackets and pedestal, embedded in wall with 25mm thick polished granite including cutting for and pinning ends of brackets or errecting stand, including brass, chromium plated, waste coupling 32mm dia with long screwed shank and fly nuts and 15mm bore dia brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S&F in repair stainless steel grating doom 125mm dia, complete all as specified and directed

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repairs swivel shower of PTMT any colour for fixing with 15mm dia pipe (Min weight 40 gms) including shower arm 15mm size 195mm long with bend of 45 degree with flange of PTMT any colour (Min weight 40 gms), complete all as specified and directed.

S&F in repairs 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed

S&F in repairs 15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed

Dismantling water storage tanks of any description, exceeding 250 litres but not exceeding 500 litres and removing from site, complete all as specified and directed.

S&F for Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, complete all as specified

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed for following bore of pipes.

2nd class soft wood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

35 mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified.

35mm thick second class hard wood, glazed and skeleton shutters, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed

30mm thick second class hard wood, glazed and skeleton shutters, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of sash bars and framing moulded, and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b); supplied and fitted to chowkhats, complete all as specified and as directed

4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, including hacking out old glass panes, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples,complete all as specified and directed

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100 mm long, mild steel cold rolled Butt hinges, medium weight, complete all as specified and directed.

75 mm long, mild steel cold rolled Butt hinges, medium weight, complete all as specified and directed.

300 mm long, mild steel helical door spring, including roller and roller plate enamelled black fixed to wooden chowkat, complete all as specified. and directed.

150mm long, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

0.63mm thick , Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

Mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed

Preparation of old decorated CGI sheet surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F PVC (SWR) bends 75mm bore dia complete all as specified and directed.

PVC (SWR) vent cowl for 110mm bore pipe and fixed, complete all as specified and directed.

PVC (SWR) vent cowl for 75mm bore pipe and fixed, complete all as specified and directed.

S&F in repairs tubular towel rail, aluminium anodised, 20mm dia, D type 60 cm long between flanges complete all as specified and directed.

S&F brackets for towel rails, complete all as specified and directed.

S&F in repair 2nd Class hard wood 40mm thick, boarding in Floors and Skirting, Planed one side, with butt joints and fixed with nails supplied and fixed, complete all as specified.

S&F in repair 2nd Class soft wood, weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, complete all as specified.

2nd class soft wood, as in scantling and similar work, clean sawn, timber framed and fixed in position, complete all as specified and directed.

Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surcaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

M&L preparation of old plastered/unplastered wall surfaces and applying two coats of cement base paint including complete removal of existing treatment, complete all as specifed and directed.

M&L 100mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base of floor, complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:4 complete all as specified and as directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of floor or roof beam haunching , lintels, cantilevers shelved including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

MS TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders, cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed.

S&F Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

S& F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding (eaves board) to wall fixed with self tapping screws as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Pre-polished 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone and including 10 mm thick screed bed in CM 1:4, complete all as specified and as directed.

Dismantling water storage tanks of any description, exceeding 500 litres but not exceeding 1000 litres and removing from site, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed.

Vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, jointing to flush pipe complete and making good to dismantled/damaged floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, fixed in repair, complete all as specified and directed .

S&F in repair vitreous china, wash hand basin, coloured, round shape, of size 550mmx400mm including brackets and pedestal, including brass, chromium plated, waste coupling 32mm dia with long screwed shank and fly nuts and 15mm bore dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed, complete all as specified and directed.

100mm cast iron sanitary connection socket to fit WC outlet, complete all as specified and directed.

S&F in repairs, 75 mm outlet, cast iron floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4), complete all as specified.

15mm bore pillar tap,fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe (fixed in repair), complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash,complete all as specified and directed.

Surface dressing not exceeding 30 cm deep and averaging 15 cm getting out in hard/dense soil, complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc of poles/stays/cables etc and getting out in any type of soil, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

RCC M-25 design mix using 20 mm graded aggregate as in Beams cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:6, complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.

Hard core of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L 75mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

Steel ventilator with top hung shutter incl hinges, steel peg stay, including one shop coat of red oxide primer, complete all as specified and directed, complete all as specified and directed.

3 mm thick figured glass pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

M&L preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

75 mm outlet, cast iron floor trap with PVC grating square 150x150x18mm in bath room and other situation including cement concrete type B1(1:2:4) for setting trap and jointed with lead joint, complete all as specified.

Tubular towel rail, brass chromium plated, 20mm dia, D type 60 cm long between flanges complete all as specified and directed.

Plain cement concrete bed 1:4:8 type D-2 (using 40mm graded crushed stone aggregates)to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipe, complete all as specified and directed.

Salt glazed stone ware drain pipe of 150mm bore (internal bore) garde 'A' laid in trenches and jointed, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in soft/disintegrated soil and making good surfaces, complete all as specified and directed

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of colour wash over a coat of white wash,complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

Point wiring with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl necessary fittings & fixture and to be turminated in sunk cast iron/pressed steel/PVC terminal boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed.

All as per srl item No-112 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed.

All as per srl item No-112 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per serial item No 112 here-in-before but for 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 4.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.0 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv, complete all as specified and directed.

Switch piano flush button types 5/6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, 5/6 pin, 5 and 15 Amp, flush type universal complete all as specified and directed.

Switch socket combination 2 in 1, outlet 5 pin, 5 Amp flush type, universal, complete all as specified and directed.

Bell, AC 230 Volt, single pole, complete all as specfied and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/Polycarbonate, isolated body, complete all as specified and directed.

S&F warm colour decorative ultra slim linear LED in replacement of 18 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed. Make : Havells Cat Part No LHEXBLP5PN1W018 or Equivalent/C&S/Bajaj.

Supply and fixing in repair, 10 Watt LED Bulk Head, IP 65, oval shaped pressure die-cast aluminium housing and ring, high quality polycarbonate diffuser in opal finish, complete all as specified and directed. Make : Havells Cat Part No LHEOAOP7UZ6W010 or Equivalent/C&S/Bajaj.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, complete all as specified and directed.

Supply and fixing in repair, LED Bulb 7 W complete all as specified and directed.

Supply and fixing in repair ceiling fan 1200 mm sweep ,copper winding, double ball bearing with aluminium blade set of 3, length of down rod not less then 300 mm, single phase , 240 volts ISI marked , including connection with three core copper wire etc complete all as specified and directed by engr-in-Charge. Make: Havells Model - Mozel 1200 mm, or Usha, Model-Striker 1200mm, or Bajaj, Model-Excel star 1200mm

Supply and fix 6 Watt, wall mounted LED picture light, aluminium material with silver finish, complete all as specified and directed. Make: Philips code No.-30973 or equivalent in CG/Havells/Wipro.

Supply and fixing in repair energy efficient highly rated, heavy duty exhaust fan 300mm sweep with louvers, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material complete all as specified and directed

Sheet metal enclosures distribution board, single pole and neutral 8 way with 200 Amps rated bus bar 240 V, double door IP-42 protection, fixed on wall duly groted in solid block wall or n wooden board with electrical connection and making good distributed wall surfaces to match with existing specification including taking down existing, complete all as specified and directed.

S&F in replacement MCB SPN, 40-63 Amp, 240 volts, 10kA, 50Hz, 'B' series and making connections, complete all as specified and directed.

MCB SP, 6 to 32 Amps, 240 Volts 10 KA, 'B' series and making connections, complete all as specified and directed.

Taking down old unserviceable electric storage water heater any type/size, supply and installation of electric storage water heater (vertical type geysers), five star rating, 35 litres capacity, 240 Volts, AC Single phase capacity having stainless steel inner tank, including heavy duty pin type fasteners 4" long as per site requirement and making necessary inlet/outlet water connections and making good disturbed surface of walls to match with existing surface complete all as specified and directed.

Steel water tubing, 25 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, laid in trenches including jointing material including taking down, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, laid in trenches including jointing material including taking down, complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 25mm dia with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed for following bore of pipes.

Supplying installing, commissioning testing in repair LT cubical feeder pillar box out door kiosk type made out of CRCA sheet 3.15mm ,3 phase 4 wire 50 C/S AC with aluminium bus bar of 250 Amps rating fixed on insulators for incoming & outgoing taping complete double door type with locking arrangement fixing on PCC platform with suitable nuts, bolts duly painted with two coats of synthetic enameled paint over a coat of red oxide primer, comprising with MCCB 160 Amps TPN 50Hzs, 35KA ( 01 Nos) in incoming and MCCB 100 Amps TPN, 25KA (01 Nos), MCB 40 Amps SPN C curve (02Nos) cable for service connection complete all as specified and as directed.

Supply laying connecting and testing in repair 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 Sqmm normal cross section 4 core including suitable size lugs laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers and remove unsv cable complete all as specified and directed. Note- Earth work and protection work shall be measured and paid for separately under respective items of BOQ.

Supply laying connecting and testing in repair 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 10 Sqmm normal cross section 2 core including suitable size lugs laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers and remove unsv cable complete all as specified and directed. Note- Earth work and protection work shall be measured and paid for separately under respective items of BOQ.

Sand cushioning to underground cable as per clause No 19.75 of SSR Part-I laid with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable. The top layer of 15cm shall be punned to 10 cm (total 23 cm) complete all as specified and directed.

Sub class ‘B’ brick old size protection cover laid dry flat transversally along the length of cable on cushioning with width equal to the length of brick complete all as specified and directed .

Material & labour for earthing complete with galvanised cast iron earth plate electrode of size 600x600x6 mm thick buried directly in ground less than 3.0m deep below normal ground level as earth electrode with top edge of the earth plate not less than 2.25mtr below ground level using GI strip 32x6mm as earth continuity conductor connected to earth plate by means of welding, GI thimbles, nuts, bolts & washers all as directed including providing earth wire protection pipe GI light grade 40mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover with handle of angle iron frame of size 40 x 40 x 6mm in PCC 1:3:6 adequate quantity of charcoal dust and salt and kalmi shore all around the earth plate, earth work in any type of soil remaining surplus excavated material all as required at site and specified in EP No 3 of SSR part I 2009 or directed by Engineer-in-charge and incl testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI strip of size 32x6mm with protection pipe of 40mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by 25%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Supply and fixing in replacement fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically, complete all as specified and directed

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 6.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.0 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv, complete all as specified and directed.

Supply and fixing angular lamp holder, PVC/Polycarbonate type with back plate for conduit fittings with LED lamp 5 watts, complete all as specified and directed.

Supply and fix in repair Wall mounted LED Batten, extruded Aluminium heat sink provided for efficient heat dissipation & integrated electronic driver of Lamp type: 18W LED life time of 30000* hours including lamp all as specified and as directed. Make: Philips, Cat Part No: TMC 501 p 1 X T-LED 22W P3241 & ESSENTIAL LED TUBE 1200 MM 18W865 T8 AP 1 (for Tube rod) or equivalent in Havells cat part No ENDURA LINEARNE OBS 20W LED 830SPC WH OR C&S CAT PART NO TARA-E 120W LTDC122 20W LED/WD .

S&F warm colour decorative ultra slim linear LED in replacement of 20 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed by EIC. Make : Havells Cat Part No LHEXBLP7PN1W020 or Equivalent/C&S/Bajaj.

Supply only, LED Bulb 7 W complete all as specified and directed.

Sheet metal enclosures distribution board, single pole and neutral 4 way with 200 Amps rated bus bar 240 V, double door IP-42 protection, fixed on wall duly groted in solid block wall or n wooden board with electrical connection and making good distributed wall surfaces to match with existing specification including taking down existing, complete all as specified and directed.

Supply laying connecting and testing, 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 6 Sqmm normal cross section 2 core including suitable size lugs laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers and remove unsv cable complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in hard/dense soil, complete all as specified and directed.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 4.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 2.50 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv, complete all as specified and directed.

M/S Haji Mohammad Sultan Sofi

M/S STARE BUILDERS

M/S BHAT CONSTRUCTION AND BUILDERS

SAMEER CONSTRUCTIONS

M/S Hilal Builders