PROVISION OF FALSE CEILING AND WALL LINING AT OPS ROOM AND INT PLANNING ROOM AND PROVISION OF DEFI OFFICE ACCN UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

Excavating in trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in depth and getting out in soft/loose soil ; complete all as specified and directed by Engr-in-charge

Material and Labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete ; complete all as specified and directed by Engr-in-charge

Material and Labour RCC M-25 (Design Mix) using 20 mm graded stone aggregates as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles ; complete all as specified and directed by Engr-in-charge

Material and Labour for RCC M-25 (Design Mix) using 20 mm graded stone aggregates as Columns, pillars, piers,posts and struts ; complete all as specified and directed by Engr-in-charge

Material and Labour for RCC M-25 (Design Mix) using 20 mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span ; complete all as specified and directed by Engr-in-charge

Material and Labour for RCC M-25 (Design Mix) using 20 mm graded stone aggregates as Chajjas, Lintel etc ; complete all as specified and directed by Engr-in-charge

Material and Labour for RCC M-25 (Design Mix) using 20 mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ; complete all as specified and directed by Engr-in-charge

Material and Labour for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips ; complete all as specified and directed by Engr-in-charge

Material and Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ; complete all as specified and directed by Engr-in-charge

Formwork to sides of fair finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter ; complete all as specified and directed by Engr-in-charge

Fair finished Square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions ; complete all as specified and directed by Engr-in-charge

Fair finished flat Form work to Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc ; complete all as specified and directed by Engr-in-charge

Fair finished flat form works to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) ; complete all as specified and directed by Engr-in-charge

Material and Labour for Brick work built CM 1:6 subclass B brick strength curved or plan exc 6m mean radius ; complete all as specified and directed by Engr-in-charge

Material and Labour for 15mm rendering in cement mortar (1:4) on brick/concrete surfaces finished the surface even and smooth without using extra cement ; complete all as specified and directed by Engr-in-charge

Material and Labour for 12mm rendering in cement mortar (1:6) on brick/concrete surfaces finished the surface even and smooth without using extra cement ; complete all as specified and directed by Engr-in-charge

Material and Labour for 5mm rendering in cement mortar (1:3) on brick/concrete surfaces finished the surface even and smooth without using extra cement ; complete all as specified and directed by Engr-in-charge

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper over coat of primer and avg 2mm thick wall care putty on walls ; complete all as specified and directed by Engr-in-charge

Material and Labour for preparation of newly plstered wall surface and applying two coats of of weather proof exterior paint over a coat of primer ; complete all as specified and directed by Engr-in-charge

Material and Labour for applying three coats of white wash on ceiling surface and ; complete all as specified and directed by Engr-in-charge

Re-Filling in floors using surplus excavated soil Spreading and levelling in layers n exc. 25 cm thick and rammed including watering ; complete all as specified and directed by Engr-in-charge

Removal of surplus soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point ; complete all as specified and directed by Engr-in-charge

Material and Labour for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder ; complete all as specified and directed by Engr-in-charge

Material and Labour for 100mm thick Cement concrete type C-2 , 1:3:6 (using 40 mm graded aggregate) as in sub base ; complete all as specified and directed by Engr-in-charge

Material and Labour for Vitrified tiles,dark shade 10mm thick (Square/ rectangular) polished, area of each tiles exc 0.42 Square Metre but n.exc 1.00 Square Metre in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 ; complete all as specified and directed by Engr-in-charge

Material and Labour for 75mm thick cement concrete type C-2, 1:3:6 using 40mm graded aggregate as in plinth protection etc ; complete all as specified and directed by Engr-in-charge

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 Square Metre.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and Fixing 10mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required, complete all as specified and directed by Engr-in-Charge

Supply and Fixing 12mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required, complete all as specified and directed by Engr-in-Charge

Supply and Fixing 450mm long Brass handles, cast type ; complete all as specified and directed by Engr-in-charge

Material and Labour for frosted to toughen glass of any thickness ; complete all as specified and directed by Engr-in-charge

Material and Labour for embossed any type of o.45X0.45m on frosted glass door ; complete all as specified and directed by Engr-in-charge

Supply and Fixing One piece Closet (WC) with soft close Seat Cover of Size 720x345x725mm including S-trap distance 220/300mm ; complete all as specified and directed by Engr-in-charge

Supply & Fixing vitreous china urinal half stall type with CP spreader white incl CP waste coupling with grating and union fordischarge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe ; complete all as specified and directed by Engr-in-charge

Supply and Fixing Vitrous china urinal partition white of size 310x770mm of approved make and fixed to wall terminating about 40cm above floor line ; complete all as specified and directed by Engr-in-charge

Supply and Fixing vitreous China wash basin (Oval Type ) including CP waste fittings 32mm, waste pipe PVC 32mm bore of required size as directed ; complete all as specified and directed by Engr-in-charge

Supply and Fixing centre hole mixer cast coppre alloy chromium plated with capston head (Pillar Mounted) srewed down high pressure with lettered hot or cold with long screwed shanks fly nut screwed for iron pipe 15mm dia ; complete all as specified and directed by Engr-in-charge

Supply and Fixing rotational moulded polythene, triple layers, water storage tank 1000Ltr capacity, closed top, cylindrical, hoisted and fixed in position including Supply and Fixing 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod ; complete all as specified and directed by Engr-in-charge

Supply and Fixing Galvanised iron steel water tubing (Medium grade), 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors ; complete all as specified and directed by Engr-in-charge

Supply and Fixing Vitrous china white (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws ; complete all as specified and directed by Engr-in-charge

Supply and fixing Chromium plated Health faucet with 1.5 metre long chain ; complete all as specified and directed by Engr-in-charge

Supply and Fixing 100mm dia CP grating with or without hinge type or hole type ; complete all as specified and directed by Engr-in-charge

Supply and Fixing CP brass towel rail 600mm long ; complete all as specified and directed by Engr-in-charge

Supply and Fixing 75mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2mtr length including) including all fittings complete all as specified and directed by Engineer-in-charge

Supply and Fixing Liquid soap dispensor set. ; complete all as specified and directed by Engr-in-charge

Supply and Fixing PVC connection 15mm size with PTMT nuts of length 600mm ; complete all as specified and directed by Engr-in-charge

Material and Labour for ATT, treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface ; complete all as specified and directed by Engr-in-charge

Material and Labour for ATT, treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall ; complete all as specified and directed by Engr-in-charge

Material and Labour for ATT, treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) ; complete all as specified and directed by Engr-in-charge

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls incl suitable white cover plate for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; ; Complete all as specified and directed by Engineer-in-charge. by Engineer-in-charge. (a) One light point/Fan point controlled by one switch NOTE: (i) Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push, etc & cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (ii) Modular metal flush boxes should be painted with a coat of red oxide to steel surface to avoid rust and rate shall be deemed to be included in the quoted rate

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls incl suitable white cover plate for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; ; Complete all as specified and directed by Engineer-in-charge. by Engineer-in-charge. (a) One 5 Amps outlet point on same board with other switches/sockets NOTE: (i) Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push, etc & cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (ii) Modular metal flush boxes should be painted with a coat of red oxide to steel surface to avoid rust and rate shall be deemed to be included in the quoted rate

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls incl suitable white cover plate for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; ; Complete all as specified and directed by Engineer-in-charge. by Engineer-in-charge. (a) One 3 pin 5 Amps socket outlet on independent board. NOTE: (i) Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push, etc & cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (ii) Modular metal flush boxes should be painted with a coat of red oxide to steel surface to avoid rust and rate shall be deemed to be included in the quoted rate

All as per ser item No. 3 here in above but point wiring with 2.5 Sqmm FRLS cable and 2.5 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board ; Complete all as specified and directed by Engineer-in-charge. by Engineer-in-charge.

Supply and Fixing modular switch 1 way 6A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular switch 1 way 16A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings including 10cm x 10cm presto plastic board for resting to holder including Supply and Fixing 01 x 10/12 watts LED lamp, 230 volts ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size ; ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete including connecting and testing ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PLUTO NEO LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size ; Complete all as specified and directed by Engineer-in-charge..

Supply, install & testing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 300mm complete fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable from ceiling rose to exhaust fan including cutting hole suitable for fixing exhaust fan ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Wall mounted fan of 400mm sweep plastic body and blade including pull cords for speed regulation & wide oscillation control, with 1300 RPM, 60 air delivery, 50 Watt, colour as per the direction of Engr-in-Charge ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 6 way, 415 volts grade with insulated rated bus bar assembly with isolated neutral bar, door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TPN/TP/SPN/SP etc, including taking down existing unserviceable one and removing from site ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing MCCB triple pole and neutral (four pole) 100 Amps, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 25 KA including making incoming and outgoing connections ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, TPN 12 way, 415 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, ; Complete all as specified and directed by Engineer-in-charge. NOTE: Necessary blank plates if required any to cover the blank MCB's place in DB and the rate shall be deemed to included in the quoted rates.

Supply and Fixing MCB single pole 5 to 32 Amps, 240 volt, 10 KA, C curve with IP-20 protected terminals including contact indication window for visual indication and safety of operator, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB SPN 32 Amps, 240 volt, 10 KA, C curve with IP-20 protected terminals including contact indication window for visual indication and safety of operator, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB TPN 40 to 100 Amps, 240 volt, 10 KA, C curve with IP-20 protected terminals including contact indication window for visual indication and safety of operator, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB TP 40 to 63 Amps, 240 volt, 10 KA, C curve with IP-20 protected terminals including contact indication window for visual indication and safety of operator, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing sub main wiring with 4 runs of 16.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 2 runs of 16.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down old unsv one from site ; Complete all as specified and directed by Engineer-in-charge. NOTE: Four runs of 16.0 sqmm copper cable and two runs of 16.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Supply and fixing sub main wiring with 4 runs of 10.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 2 runs of 10.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down old unsv one from site ; Complete all as specified and directed by Engineer-in-charge. NOTE: Four runs of 10.0 sqmm copper cable and two runs of 10.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Supply and fixing sub main wiring with 4 runs of 6.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 2 runs of 6.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down old unsv one from site ; Complete all as specified and directed by Engineer-in-charge. NOTE: Four runs of 6.0 sqmm copper cable and two runs of 6.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Material and Labour for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth of not less than 1.5 m below normal ground level, connected to glavanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts & washers and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 25mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade from top of the earth electrode raised upto a level of 50cm above ground level, MS funnel with wire mesh embeded in earthing pit of size 30x30x30cm in PCC (1:3:6) type C-1 incl exposed surfaces smoth finished with 15mm thick cement mortar (1:6), RCC pre-cast (1:2:4 type B-1) cover slab of 40mm thick with 2 Nos. MS handles of 12mm dia suitable for carrying of pit cover, Angle iron frame made out of 40x40x4mm angle iron for 30x30mm PCC pit for holding the pit cover including providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance n. exc. 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 ; Complete all as specified and directed by Engineer-in-charge. NOTE: (a) Cost of excavation, earth work, watering pipe, test point, MS Funnel with wire mesh and PCC pit with cover will be deemed to be included in the quoted rate. No extra cost shall be paid to the contractor against these items. (b) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor & no extra cost will be given to the contractor.

Supply and Fixing storage electric heater (Geyser), flexible mounting of capacity 25 ltrs, single phase, 240 volts, AC, white colour, ISI marked BEE 5 star rated complete with high precision & externally adustable capillary thermostat for temp regulation, backup safety overheating capillary therrmal cut out at 95ºC, temperature display, etc., including provn of new suitable holding clamp, MS bolts, grouted to wall and connecting up including 3 core sheathed multi-stranded flexible copper conductor cable connected with 15/16 Amp plug top and provn of water connections with new PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers brass union, NRV of suitable size, check/end nuts with washers, 15mm dia 100mm long nipples (02 Nos) for hot water and cold water connections including writing MES No. and making good to the disturbed surface in cement morter as required and testing ; Complete all as specified and directed by Engineer-in-charge. NOTE: Cost of flexible copper cable of 3 core, PVC steel braided inlet/outlet pipe of 15mm dia, 450mm long with brass union, NRV, check/end nuts, nipples, MS bolts, etc., and minor parts, if any, other than those are not specified in the schedule and required for smooth functioning of geyser will be deemed to be included in the quoted rate

Material and Labour for GI pipe light grade 40 mm dia Tubes, with all fitting and fixed complete to walls and ceilings or laid in floors complete for protection of cables ; Complete all as specified and directed by Engineer-in-charge.

Supply and Laying in trenches or drawn through pipe or fixed on wall / poles , LT UG cable 1100 Volts, heavy duty XLPE insulated, screened, PVC bedded, galvanised steel strip or wired armoured with aluminium conductor after removing old one of size 70 Sqmm 31/2 core, ; Complete all as specified and directed by Engineer-in-charge.

AC/REV/05/2023-24 Material and Labour for Providing and fixing Gypsum board 12 mm thick in ceiling fixed with screw as per manufacturers instructions incl preparation of new surfaces & applying two coat of OBD on ceiling including dismantaling of old boarding any type ; complete all as specified and directed by Engr-in-charge

Supply and Fixing GI frame work for seameless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixe to surrounding wall using nylon sleeves and screws as 450mm centre to centr/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including demolition of old framing ; complete all as specified and directed by Engr-in-charge

Supply and Fixing Hangers 4 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including removing old material ; complete all as specified and directed by Engr-in-charge

Supply and Fixing of woodlot Ceiling/Wall lining soundproof and acoustics made of FR grades 2430mmX131mmX16mm made of MDF backed with acoustic fleece providing sound absorption of 0.88 NCR as per ISO 354, installed with 15mm aluminium profile conforms to aluminium alloy 6063-T6, tempered as per BS:1474-1987 and GI lock in clips on the back of tongue and groove system. The density per panel is 750-800 Kg/Cum. The panel comes with tongue and and grooves for eamless pattern with 4-28mm Groove and visible panel. These slates are made from acoustic fibre board with linear perforation for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustic fleece. Achieves sound reduction of 0.88 NCR, installed on and including GI studs 600mmX600mm centre to centre 2400mmX50mm web thickness 0.5mm, flanges 15mm & 50mm fully knurled giving it high strength, Hot dipped galvanised steel with 120 GSM zinc coating specially designed for acoustic vibration manegement and long life with & including backing of 50mm thick, 1000 GSM absorb wool tested as per fire retardent ASTMD 635 of 1991 insulation and IS 15061-2002 for excellent results, ; complete all as specified and directed by Engr-in-charge Make:- HILUX, RITE, SAINT GOBAIN, ANUTONE, ARMSTRONG, PROMAT, HIMALAYA.

S S CONSTRUCTION COMPANY

Saini Constructions

M/S MAHAJAN CONSTRUCTION CO

tarlok singh contractor

GEE EMM ASSOCIATES

Sai Construction Co.

Santokh Singh and Associates