Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹12.2 LAccepted-Finance | L1 | Accepted-Finance Quoting Lowest rate | |
| 2 | L2₹12.4 L+₹20,268 (1.66%)Rejected-Finance | L2 | Rejected-Finance Quoting Higher rate | |
| 3 | L3₹13.1 L+₹84,183 (6.88%)Rejected-Finance | L3 | Rejected-Finance Quoting Higher rate |
| Sl No | Description | Qty | Unit | M/S GRACIOUS ENGINEERING PROJECT L3 | ADHISHARM INDUSTRIALS L1 | DURGAPUR POWER L2 |
|---|---|---|---|---|---|---|
| 1.00 | LT PANEL Supply, delivery and installation of fabricated cubical type compartmentalized dust and vermin proof Floor cum wall mounted L.T. distribution panel board of suitable size made of 2 mm (14 SWG) thick M.S. sheet reinforced with (40x40x6 mm) angle iron frame work with individual hinged door with locking arrangement for all compartment and providing suitable ventilation arrangement. The complete panel board shall be painted by power coating paint, colour siemens white. The interconnection should be done with suitable size tinned copper strip between BBC to all main switches and other accessories including suitable stud connectors, socketing etc as required and earthing by nut, bolt in the body complete with base channel. The lower size of the base of panel board should rest on frame work (75x40x5 mm). The control panel will have suitable cable entry from bottom through data cable gland plate to access sufficient no. of cables as per direction of E.I.C. the panel comprising with following switches.(Make: Approved make of P.W.D & Work shop Panel .)
Incoming : 315A, 415V FP SFU with propet HRC fuse (open execution type) --- 1 no. | 1 | Item | 3,25,000 ₹3,25,000 | 2,98,950 ₹2,98,950 Lowest | 3,10,000 ₹3,10,000 |
| 1.01Painting : Board should be properly degreased, derusted before phospheting. Alkaline Melamine Epoxy based Powder coated paint to be done with minimum thickness of 70 micron avg. Shade will be Pebble Grey, No.RAL 7032 both inside and outside. 'CENTRAL POWER RESEARCH INSTITUTE' type test report for the Panel Board for Three phase and Neutral short circuit withstand strength test on main circuit BusBars to be Furnished. | ||||||
| 1.02415V, 315 Amp 4 nos (4x40x5mm ) copper bus-bar with necessary nos of holes and different colour insulating tape on epoxy bus support.- 01 set suitable length each having for Phase and N. Busbar material will be Electrolytic Gr Copper, 90% & above pure in nature, semi soft, tined electroplated with heat srinkable PVC sleeve. (Certificate from Mfg. with challan to be submitted). 5.6 Gr Stainless Steel Bolt to be provided for Bus Bar Connection & spring washers to be provided for Bus Bar Connection. | ||||||
| 1.03Termination : Incoming cable termination Bus should be suitable for termination of requisite nos. of Ar/Al XLPE/PVC cables. Outgoing feeder terminals should be as per rating. | ||||||
| 1.04System Voltage : 415V, 50Hz, RYBN. Control wiring cable size : 1.5 sqmm PVC FR Cu multistrand flexible wire with proper socketing with PVC sleeve & identification ferruling. CT Secondary wiring to be done with 2.5 sqmm PVC FR Cu multistrand flexible wire. (Mk. RR Kabel / Havell's / Polycab/KEI). | ||||||
| 1.05Outgoing : i)250A,415V TPN Change over switch(open execution type) ii) 315A, 415V TPN SFU with propet HRC fuse (open execution type)----1no. ii) 100A, 415V TPN SFU with propet HRC fuse(open execution type)----5 nos. iii) 63A, 415V TPN SFU with propet HRC fuse(open execution type)---- 2 nos. Suitable size of cable alleys on both sides provided. | ||||||
| 1.06Digital Multifunction Meter with selector switch --- 1 no. LCD single function Meter ( Make Siemens- 7KT0311),LED type indicating lamp with colour glasses ( Red / Yellow / Blue / Green) - quantity as per required of site (for incoming indication for 3 phase ) 50 / 5A, 5 VA, Cl.1 CT Coil (Mk. AE) - 3 nos. EI Danger Board --- 1 Nos. Supplying & Fixing 6 Amp SP MCB---- 3 nos. Slide lock fuse---- 3 nos. Make: L&T,Siemens approved by EIC. | ||||||
| 1.07Interconnection -- i. From Input Main switch to Busbars - 4 x 50mm x 5mm Cu bars covered by coloured PVC Heat shrink. ii. From Busbars to 100/125 A output Main switch - 4 x 25 mm x 5 mm Copper bars covered by coloured PVC Heat shrink. iii. From Busbars to 63 A. output Main switch - 25 sq.mm. Copper wires (1.1 KV voltage grade single core stranded 'FR' PVC insulated & unsheathed copper wire) | ||||||
| 1.08The complete panel board is to be installed on suitable brick padestal as directed by the E.I.C. All incoming/outgoing switches is to be properly lebeled on Acrylic sheet as per direction of EIC. | ||||||
| 1.09Note: Panel drawing must approved by EIC prior to start the work. Catagory and model of diffrent switches should be approved before to start the work. An Auto Cad Drawing of the panel has to approved by EIC before making of panel. Enclosure shall provide Degree of protection IP -42/43 in accordance with IS : 2147 -1962 with its latest ammendment. The Panel box will be fabricated by CPRI approved fabricator. Approval should be submitted along with the drawing. ( DG Distribution Panel) | ||||||
Tender Value
Refer Docs
EMD Value
₹24,100
Closing Date
2 Jun 2026, 11:00 amClosed
Sr.Superintending Engineer
Office of the Sr. Superintending Engineer, Western Electrical Circle , PWD, Purta Bhavan, 1st floor, Burdwan-713103
Urgent repairing and rectification work of the electrical panel and panel room at ADM Bungalow near Polo Ground, Asansol, under Asansol Electrical Subdivision II, PWD
2026_WBPWD_5014103_1
WBPWD/SSEWEC /AED /NIQ-02 /2026-27
Open Tender
ELECTRICAL WORKS ORG
Item Rate
14 days
Asansol
Please refer Tender documents.
5 documents required · 5 mandatory
₹24,100
Office of the Sr. Superintending Engineer, Western
8 Jun 2026
15 May 2026
4 Jun 2026
15 May 2026
2 Jun 2026
21 May 2026
15 May 2026 - 20 May 2026
20 May 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1LT PANEL Supply, delivery and installation of fabricated cubical type compartmentalized dust and vermin proof Floor cum wall mounted L.T. distribution panel board of suitable size made of 2 mm (14 SWG) thick M.S. sheet reinforced with (40x40x6 mm) angle iron frame work with individual hinged door with locking arrangement for all compartment and providing suitable ventilation arrangement. The complete panel board shall be painted by power coating paint, colour siemens white. The interconnection should be done with suitable size tinned copper strip between BBC to all main switches and other accessories including suitable stud connectors, socketing etc as required and earthing by nut, bolt in the body complete with base channel. The lower size of the base of panel board should rest on frame work (75x40x5 mm). The control panel will have suitable cable entry from bottom through data cable gland plate to access sufficient no. of cables as per direction of E.I.C. the panel comprising with following switches.(Make: Approved make of P.W.D & Work shop Panel .) Incoming : 315A, 415V FP SFU with propet HRC fuse (open execution type) --- 1 no. | |||||
| 1.01 | Painting : Board should be properly degreased, derusted before phospheting. Alkaline Melamine Epoxy based Powder coated paint to be done with minimum thickness of 70 micron avg. Shade will be Pebble Grey, No.RAL 7032 both inside and outside. 'CENTRAL POWER RESEARCH INSTITUTE' type test report for the Panel Board for Three phase and Neutral short circuit withstand strength test on main circuit BusBars to be Furnished. | - | - | - | - |
| 1.02 | 415V, 315 Amp 4 nos (4x40x5mm ) copper bus-bar with necessary nos of holes and different colour insulating tape on epoxy bus support.- 01 set suitable length each having for Phase and N. Busbar material will be Electrolytic Gr Copper, 90% & above pure in nature, semi soft, tined electroplated with heat srinkable PVC sleeve. (Certificate from Mfg. with challan to be submitted). 5.6 Gr Stainless Steel Bolt to be provided for Bus Bar Connection & spring washers to be provided for Bus Bar Connection. | - | - | - | - |
| 1.03 | Termination : Incoming cable termination Bus should be suitable for termination of requisite nos. of Ar/Al XLPE/PVC cables. Outgoing feeder terminals should be as per rating. | - | - | - | - |
| 1.04 | System Voltage : 415V, 50Hz, RYBN.
Control wiring cable size : 1.5 sqmm PVC FR Cu multistrand flexible wire with proper socketing with PVC sleeve & identification ferruling. CT Secondary wiring to be done with 2.5 sqmm PVC FR Cu multistrand flexible wire. (Mk. RR Kabel / Havell's / Polycab/KEI). | - | - | - | - |
| 1.05 | Outgoing : i)250A,415V TPN Change over switch(open execution type) ii) 315A, 415V TPN SFU with propet HRC fuse (open execution type)----1no.
ii) 100A, 415V TPN SFU with propet HRC fuse(open execution type)----5 nos.
iii) 63A, 415V TPN SFU with propet HRC fuse(open execution type)---- 2 nos.
Suitable size of cable alleys on both sides provided. | - | - | - | - |
| 1.06 | Digital Multifunction Meter with selector switch --- 1 no.
LCD single function Meter ( Make Siemens- 7KT0311),LED type indicating lamp with colour glasses ( Red / Yellow / Blue / Green) - quantity as per required of site (for incoming indication for 3 phase )
50 / 5A, 5 VA, Cl.1 CT Coil (Mk. AE) - 3 nos.
EI Danger Board --- 1 Nos.
Supplying & Fixing 6 Amp SP MCB---- 3 nos.
Slide lock fuse---- 3 nos.
Make: L&T,Siemens approved by EIC. | - | - | - | - |
| 1.07 | Interconnection -- i. From Input Main switch to Busbars - 4 x 50mm x 5mm Cu bars covered by coloured PVC Heat shrink.
ii. From Busbars to 100/125 A output Main switch - 4 x 25 mm x 5 mm Copper bars covered by coloured PVC Heat shrink.
iii. From Busbars to 63 A. output Main switch - 25 sq.mm. Copper wires (1.1 KV voltage grade single core stranded 'FR' PVC insulated & unsheathed copper wire) | - | - | - | - |
| 1.08 | The complete panel board is to be installed on suitable brick padestal as directed by the E.I.C. All incoming/outgoing switches is to be properly lebeled on Acrylic sheet as per direction of EIC. | - | - | - | - |
| 2LT PANEL Supply, delivery and installation of fabricated cubical type compartmentalized dust and vermin proof Floor cum wall mounted L.T. distribution panel board of suitable size made of 2 mm (14 SWG) thick M.S. sheet reinforced with (40x40x6 mm) angle iron frame work with individual hinged door with locking arrangement for all compartment and providing suitable ventilation arrangement. The complete panel board shall be painted by power coating paint, colour siemens white. The interconnection should be done with suitable size tinned copper strip between BBC to all main switches and other accessories including suitable stud connectors, socketing etc as required and earthing by nut, bolt in the body complete with base channel. The lower size of the base of panel board should rest on frame work (75x40x5 mm). The control panel will have suitable cable entry from bottom through data cable gland plate to access sufficient no. of cables as per direction of E.I.C. the panel comprising with following switches.(Make: Approved make of P.W.D & Work shop Panel .) Incoming : 315A, 415V FP SFU with propet HRC fuse (open execution type) --- 1 no. | |||||
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 17.49 MB
BOQ_5082073.xls
BOQ • 0.32 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .