PROVN OF FUEL STORE IN 21 WEU AT ZAKHAMA MILITARY STATION UNDER AGE (I) ZAKHAMA

Amount

Surface dressing n exc 15 cm deep in soft/loose soil.

Excavation over area, n. exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes, laying of cable etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for hardcore with broken stone or boulder of gauge not exc 63 mm, deposited , spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 40mm thick damp proof course 1:2:4 type B0(using12.50mm graded stone aggregate) and applying evenly a tack coat of blown bitumen 85/25 @ 1.5kg per sqm. and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and as directed.

M&L for RCC type 1:2:4, type B-1 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressumers, lintels over 1.5m span etc. complete all as specified and as directed. (Note : Reinforement shall be measured and paid separately under relevant of this schedule)

Use and waste formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc. in rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for RCC type 1:2:4, type B-1 (using 20mm graded stone aggregate) as in Chajjas complete all as specified and as directed. (Note : Reinforement shall be measured and paid separately under relevant of this schedule)

Use and waste formwork to Chullah hoods,chajjas, troughs,and similar items incl edges in rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cutting, bending cranking, hooking end and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed.

M&L for mild steel TMT bars 8 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M & L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 3% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

Supply only integral water proofing compound complete all as specified and as directed. Note:- Dose of WPC shall be as per manufacturer instruction and the same shall be recorded in the MB.

M&L for preparation of newly plastered surface of walls and applying Three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.

M & L for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and as directed.

M & L for preparation of new steel surface over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in Ridges/valley gutter, fixed with self tapping screws complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B1 (using 40mm graded stone aggregate) as in Floor complete all as specified and directed.

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces,hold fast etc, complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe 410-W(Gde-E- 250)quality-A complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) channels. square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment GDE Fe410-0 or Fe 310-O complete all as specified and as directed.

M & L for 2nd class hardwood, weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30mm laps complete all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

M&L for 100 mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for forming contraction (Dummy) joints 75 mm x10 mm wide ,filled with sealing compound complete all as specified and directed.

Supply only mettalic floor hardner complete all as specified and as directed.

M&L for 100 mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in top layer, surfaces finished even and fair complete all as specified and directed.

M&L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed.

M&L for Pre-Cast Plain Cement Concrete (1:3:6) type C1 using 20mm graded stone aggregate as in bond stone set in Cement Mortar 1:6 complete all as specified and as directed.

M&L For extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, using 20mm thick Granite or Trap stone complete all as specified and as directed.

M&L for raised pointing to random or ploygonal rubble, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and as directed.

S&F for (SWR) pipes,75mm bore single socket in any length with rubber ring joint, weep hole etc complete all as specified and as directed.

M&L for hand packing any thickness of broken stone or boulder at back of wall pitching, laid dry, hand packed tightly complete all as specified and as directed.

M & L for PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) as in benching and coping, cills, hold fasts, fixing of post, water trough etc. including necessary formwork (straight or curved) complete all as specified and as directed.

J C DUTTA (BID ID -3216331)

M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE (BID ID -3212340)