Augmentation of Ahraura Nagar Palika Parishad Water Supply Scheme. District-Mirzapur

R.C.C Overhead Tank

Supply of all materials labour, T&P etc. preparation of design & drawing, vetting of design of reputed institution for complete the construction of R.C.C. (M30 Grade) Over Head Tank of FOLLOWING CAPACITY min 0.6m above ground level with main components, soil testing and assuming bearing capacity of soil as 8MT including cost of supply of design and drawings. all the water retaining components of OHT shall be casted in M-30 grade cement concrete and minimum grade of concrete of foundation and staging should be M-25 with approved cement, coarse sand and stone grit as per I.S. 11682 and I.S. 456 seismic effects and wind load should be taken into consideration as per I.S. 1893 for earthquake resistance and I.S. 875 Part-III for wind load on structure and including 1M wide RCC dog legged staircase with separate 2 columns & BEAM, 1m wide R.C.C.(M30) balcony, M.S. ladder made of 65x65x8mm angle section and 20mm ribbed M.S. bars with hand rails of 20mm dia medium class G.I. pipes, one aluminum ladder inside the tank from top dome to bottom dome, R.C.C. railling with 20mm dia medium class G.I.pipe (in 3 rows) on both sides of stair case, supported on 65x65x8mm M.S. angle section, spaced at intervals not more than 1.5m, proper ventilator at top dome in circular shape of 1.5m dia, Ultra Sonic Water Level Indicator fabricated with sensor connecting to scada automation, lightening conductor as per I.S. 2309 or its latest amendments of latest electricity rules, consisting of proper elevation rod with 5 or more fork points as prescribed in IS 2309-1969 and IS 3013-1966, C.I. manhole of min 60x60cm size with locking arrangement, supply, fixing, jointing of D.I. D/F Pipes of appropriate size with D.I. D/F specials conforming to IS 8329/2000 as vertical pipes for all required no of seperate inlet on each t/w(150mm OR as designed), all required no of outlet (350mm or as designed for each DMA),350 MM DIA. overflow and 100 MM DIA.wash out as per latest/relevant I.S. specification with all jointing materials for proper completion of work along with Sluice valves with actuators, construction of bed blocks in 1:2:4 PCC with cement, coarse sand and approved stone grit, construction of washout/ overflow chamber and chambers for sluice / butter fly valves as per departmental type design and drawings, supply of 350mm dia DI K-7 pipe as per I.S.-8329/2000 for disposal of water from overflow and washout chamber to suitable point outside the water works compound, SITC 6 nos 200 watt wall mounted LED Light (Crompton/phillips/Bajaj/orient) with all neccessory required equipment, wire, switches/MCB etc., food grade epoxy rasin 3 coat on the inner wall of OHT Tank, 2coat apex ultima weatherproof painting over primer coat, 3 coat enamel painting over primer coat on steel, GI pipe works (water container & drinkingwater touch all parts, internal painting 3 coat food grade epoxy). Including all shuttring and scafolding etc. supply of all materials, labours, T&P etc all complete the work upto the satisfaction of Engineer-In-Charge.

Zone-3, 500KL/25M

Zone -4, 800KL/18M

Zone-1 Construction and desing of RCC circular Clear Water Reservoir (CWR) 1000 KL including supply of all Materials, Labours, T & P etc. Complete including excavation in rock, making the approach road complete.

Repair and Maintenance of existing RCC OHT 600KL/15M including cleaning of silt/malwa/algae, repair of seepage/leekage by gun grouting method, dismentaling of old damaged Flooring and Construction of new flooring with 40mm thick M-15 cement Concrete flooring in glass pannels over 75mm thick (1:4:8) PCC base with 3mm thick floating coat of neat cement, removing of weak concrete, repairing of OHT Coloumn, by hacked roughened surface and clean throughly and its repairing with jacking of cement concrete M-20 in 60mm thickness around old damaged coloumn, repairing of all raling of stair, balcony with 20mm dia GI Pipe including changing of old damaged pipe, repairing/changing of old damaged lighteing conductor including fixing of aluminium strip with column and making proper earthing, dismentaling/fixing of inlet, outlet, overflow and washout pipe with clamp of OHT, changing of inlet, outlatet and washout unserviceable sluice valve incluing dismentaling of old S/v and fixing of new S/v and construction of S/v masonary chamber, supplying and fixing of additional column pipes of 200mm dia, supply of garden mess for repairing of construction of verticle wall and bottom dome. 12mm thick plaster 1:3 cement and coarse sand and water proofing compund chemical over the tank internal wall and bottom dome, repairing and changing of old damaged manhole cover, repairing of ventilation jali including supply and ,fixing of safety gate(not less 125kg) on staircase with pillar ,fixing of required MS work and Repair of all RCC work (columns,brace,balcony, bottome dome, top dome, staircase, post, conical wall etc.) including cost of reinforcement, food grade epoxy rasin 3 coat on the inner wall of OHT Tank, 2coat apex ultima weatherproof painting over primer coat. 3 coat enamel painting over primer coat on steel, GI pipe works. SITC 6 nos 200 watt wall mounted LED Light (Crompton/phillips/Bajaj/orient) with all neccessory required equipment, wire, switches/MCB etc., Including all shuttring and scafolding etc., Supply of all materials, labours, T&P etc all complete the work upto the satisfaction of Engineer-In-Charge. NDT Report of all major component of OHT will be submited by Contractor before repairing work.

Provision for survey investigation by any Govt. institution and dismmentaling works of existing OHT-135kl/12 m staging in Zone 2 behind NPP office as per recommendation of committee, including all supply of labour T&P complete(including disposal of scraps and Malva etc all).

PUMP HOUSE

Provide all materials, labour, T&P

Rising Main

etc. complete and construct Pump house size (3.6x3.0x3.0)m - cum- Chlorinating room size (1.80x2.5x3.0)m as per departmental type design with ByPass Chamber including ISMB-250 all labour material T&P etc complete.

Provision for repairing of existing pumphouse located in NPP Ahraura including dismentling & Repairing of necessary rcc work, brick work, roof treatment, flooring, plastering, finising and painting in patches on whole surface , repairin of door, windows, ventilation, sunshed, rain water pipe, drain, Repairing of damaged electrification, SITC 2 nos 180 watt wall mounted LED Light (Crompton/phillips/Bajaj/orient) with all neccessory required equipment, wire, switches/MCB etc., painting of outer surface with approved exterior weather coat apex ultima paint and inner surface with approved interior paint etc. disposal of malwa up to 8.0 km distance, complete the work upto the satisfaction of Engineer-In-Charge.

Supply of following sizes (D.I. K-9) pipes for rising main/distribution system conforming to latest/relevant I.S. 8329/2000 Specifications with all jointing materials such as specials conforming to latest /relevant I.S. specifications, suitable for D.I pipes, as per IS‐1239 /2000 and IS 8329/2000 or their latest amendment including F.O.R. destination and all taxes and insurance etc. with loading, unloading and Carting up to site of work, also including specials for these pipes and lowering them into the trenches and laying true to alignment and gradient and jointing etc. complete (including testing of pipe lines and cutting of pipes for making up the length but excluding the cost of trenches).all complete as per instructions of Engineer ‐in ‐ charge including Supply and Fixing of specials etc complete.

100 mm dia K‐9

Supply of all labour, materials and T & P etc. and construct staff quarter for maintenacne staff in water works compound. as per departmental type design and drawing (39.46 Sqm plinth area) (Only RCC framed structure, plinth above 60 cm. Nearest road level).

Construction of Camp office cum staff room with all facilities (1.5 ton AC- 1 No., 1 No. Confrence Table, 04 Nos., Big table, 25 Nos. Chaires and 03 Nos. Desktop with printer and table) as per approved design and drawing (Only RCC framed structure, plinth above 60 cm. Nearest road level).

Dismantling of roads for laying of pipe line including sorting out and stacking of serviceable materials, stacking and disposal of unserviceable materials upto a distance of 8 Km.

Supply of following sizes (D.I. K-9) pipes for rising main/distribution system conforming to latest/relevant I.S. 8329/2000 Specifications with all jointing materials such as specials conforming to latest /relevant I.S. specifications, suitable for D.I pipes, as per IS‐1239 /2000 and IS 8329/2000 or their latest amendment including F.O.R. destination and all taxes and insurance etc. with loading, unloading and Carting up to site of work, also including specials for these pipes and lowering them into the trenches and laying true to alignment and gradient and jointing etc. complete (including testing of pipe lines and cutting of pipes for making up the length but excluding the cost of trenches).all complete as per instructions of Engineer ‐in ‐ charge including Supply and Fixing of specials etc complete.

100 mm dia K‐9

Carting from (upto 8 Km) the following sizes of D.I. Pipes (class K-9) and A.C.pipes ( class-15) and specials to the site of work, lowering them in to trenches and laying true to alignment and gradient including testing of pipeline ( but excluding cost of trenching and cutting of pipes etc. for making of lengths but including making joints)

100 mm dia K-9

125 mm dia

150 mm dia

100 mm dia

Supply of the following HDPE Pipes as per I.S. code no. 4984/2016 or its latest amendment includi

CC road

Interlocking road

Bituminous road

Reinstatement of following type of roads dismantled during laying of pipe line including supply of all materials, labour and T & P etc. required for proper completion of the work.

Interlocking Road (50% New Interlocking bricks 80 mm thick M-30 grade & 50% Old usable interlocking on 20cm local sand & 10cm TH. PCC 1:6:12 using brick blast ). inclu. Entire surface Spreading 3 cm local sand for paste of brick & joint filling.

Sluice/ wheel Valve (Masonary type) with extra heavy duty MS cover.

ng cost of HDPE electro fusion coupler joint per pipe length and inclusive of all taxes and duties, 3rd party inspection charges, packing and forwarding charges, trasnit insurance charges, road transportation charges etc. F.O.R. destination etc. complete.

SP (stone pitching) road

Supply of all materials,labour, and T & P etc. and construct R.C.C.thrust blocks. Including mild steel works all complete

R.C.C. M-20 grade 100 mm dia

R.C.C. M-20 grade 150 mm dia

300 mm dia. D.I. (K-7 pipes)

250 mm dia. D.I. (K-7 pipes)

200 mm dia. D.I. (K-7 pipes)

Distribution System

Supply of the following D.I. pipes (k-7) conforming to I.S -8329/2000 or its latest amendment(s). Including F.O.R. destinations rate per metre in Rs., anywhere in U.P. including cost of one Rubber Gasket per pipe length & iniclusive of all Taxes &Duties, Third Party Inspection Charges, Packing & Forwarding Charges, Transit Insurance Charges, Road Transportation Charges etc.

160 mm dia HDPE Pipe PN‐6: Class PE‐100

140 mm dia HDPE Pipe PN‐6: Class PE‐100

110 mm dia HDPE Pipe PN‐6: Class PE‐100

Provision for processing fees for NOC from other department such as forest, irrigation department, IOCL and other all.

Ordinary Soil

Dismantling of roads for laying of pipe line including sorting out and stacking of serviceable materials, stacking and disposal of unserviceable materials upto a distance of 8 Km.

Bituminous surface (20cm sand, 20cm GSB, 20cm WMM, 5 cm to 8 cm DBM, 3cm to 4 cm B.C.) payment made upto WMM- 50%, DBM- 30% and BC with testing in NABL aprooved lab/PWD- 20%.

150 mm dia. D.I. (K-7 pipes)

300 mm dia. D.I. (K-7 pipes)

250 mm dia. D.I. (K-7 pipes)

200 mm dia. D.I. (K-7 pipes)

Distribution System

Supply of the following D.I. pipes (k-7) conforming to I.S -8329/2000 or its latest amendment(s). Including F.O.R. destinations rate per metre in Rs., anywhere in U.P. including cost of one Rubber Gasket per pipe length & iniclusive of all Taxes &Duties, Third Party Inspection Charges, Packing & Forwarding Charges, Transit Insurance Charges, Road Transportation Charges etc.

160 mm dia HDPE Pipe PN‐6: Class PE‐100

140 mm dia HDPE Pipe PN‐6: Class PE‐100

110 mm dia HDPE Pipe PN‐6: Class PE‐100

100 mm dia. D.I. (K-7 pipes)

Sluice/wheel valve

PUMP SET: (Zone 3)

600LPM, 82/84 Meter head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 03 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

Scour Valve - 100 mm dia

Air valve - 25 mm dia

Fire Hydrant - 80 mm dia.

Carting of following sluice valves store to site of work, lowering, fixing and jointing of following fitting in trenches :

PUMP SET: (Zone 3)

600LPM, 82/84 Meter head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 03 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

Scour Valve - 100 mm dia

Air valve - 25 mm dia

Fire Hydrant - 80 mm dia.

Supply of the following HDPE Pipes as per I.S. code no. 4984/2016 or its latest amendment includi

BT Road

Carting of following pipes, specials and fittings from site store to site of work, lowering them into trenches, laying true to alignment and gradient, laying and jointing of pipe line including cutting of pipe for making up length as required for proper completion of work DI Pipe -8329/2000

CC Road

Supply of following size sluice valve make DI DF Non Rising Cost iron Sluice valve as per IS 14846 : 2000 PN 10/PN -16

Reinstatement of following type of roads dismantled during laying of pipe line including supply of all materials, labour and T & P etc. required for proper completion of the work.

ng cost of HDPE electro fusion coupler joint per pipe length and inclusive of all taxes and duties, 3rd party inspection charges, packing and forwarding charges, trasnit insurance charges, road transportation charges etc. F.O.R. destination etc. complete.

Interlocking Road (50% New Interlocking bricks 80 mm thick M-30 grade & 50% Old usable interlocking on 20cm local sand & 10cm TH. PCC 1:6:12 using brick blast ). inclu. Entire surface Spreading 3 cm local sand for paste of brick & joint filling.

C.C. Road in M25 grade, minimum thickness 15cm on 15cm sand & 20cm GSB filling base.

Supply of all labour, materials, T&P etc. all complete and construction of following valve chambers as per type design.

Mixed Soil and replace of ordinary soil.

soft Rock and replace of ordinary soil.

Interlocking Road (50% New Interlocking bricks 80 mm thick M-30 grade & 50% Old usable interlocking on 20cm local sand & 10cm TH. PCC 1:6:12 using brick blast). inclu. Entire surface Spreading 3 cm local sand for paste of brick & joint filling.

SP (stone pitching) road with 20 cm. local sand, 20 cm GSB, 3 cm local sand entire surface spreading and bituminous filling every joints.

Construction of Control Station room (SIZE 4.5Mx3.6Mx4.0M) as per approved design and drawing (Only RCC framed structure, plinth above 60 cm. Nearest road level).

Construction of 1.8 m height Boundary wall with RCC Column arround water works compound and Tubewell complete including supply of all materials, labour, T&P etc. complete required for proper completion of the works (plinth not less than 60 cm.).

SP Road

TL Road

HOUSE CONNECTION

For house connection dismentelling of all type of road surface, breaking of all type of floor, wall, and disposal of unserviceable materials up to 5km distance.

Tile Road

B.T. Road

S.P. Road

C.C. Road

Making House Connection should be done from new distribution pipe line to outer wall of house or 2.0 m inside the boundary wall with provision of tap including supply of 7.0 m HDPE Pipe 20mm dia, PN-12.5, PE-100, SDR-6 (0.6m depth below ground level), and 4.0 m 15mm dia (ID) G.I. pipe, Class-B and keeping the G.I. pipe atleast 1.0 m in height above the G.L. as per department type design and drawing including supply of specials, saddle, clamps etc. of suitable size, ISI Mark 6mm BRASS FERRULE conforming to latest/ relevant I.S. 2692/1989 or their latest amendmen, BRASS Tap, all Materials, labours, T&P etc. complete, , Excavation pit/trench, cutting of pipe, Bailing out of water, carting and lowering them into the already prepared trenches, fixing in position and jointing them with pipelines and testing etc., Grountig by CC 150 mm x 150 mm x 150 mm size in M20, and 3 no.s GPS Location colour photographs submitted after completion of works . Also including G.I.S Based Survey to collect all required data in Projected Area Nagar Palika Parishad Ahraura for proper completion of work as per Drawing. as per instructions of Engineer in charge.

new connection in HDPE/ PVC/ CI/ DI/ MS Pipe upto 300mm dia

C.C. Road in M25 grade, minimum thickness 15cm on 15cm sand & 20cm GSB filling base.

ng cost of HDPE electro fusion coupler joint per pipe length and inclusive of all taxes and duties, 3rd party inspection charges, packing and forwarding charges, trasnit insurance charges, road transportation charges etc. F.O.R. destination etc. complete.

Interlocking Road (50% New Interlocking bricks 80 mm thick M-30 grade & 50% Old usable interlocking on 20cm local sand & 10cm TH. PCC 1:6:12 using brick blast ). inclu. Entire surface Spreading 3 cm local sand for paste of brick & joint filling.

Fire hydrant chambers with extra heavy duty MS cover.

Sluice Valve (surface box type) with extra heavy duty MS cover.

Air valve chambers with extra heavy duty MS cover.

existing connection shifting in HDPE/ PVC/ CI/ DI/ MS Pipe upto 300mm dia

Supply and fixing of 1.2M wide Wicket Gate with 1.8 m height as per type design including fabrication and supply of steel and construction of RCC boundary pillars including plaster, putty,priming coat and painting etc complete as per direction of engineer in charge

Excavation of earth in ordinary soil (loam, clay or sand) for pipe line and rising main trenches including lift upto 1.50 m and lead upto 50 m and refilling watering, ramming of the excavated earth into the trench including reinstatement of damaged underground and overhead utilities and also disposal of surplus earth upto 8 Km. from the center of the trenches including supply of all material labour, T&P etc complete as per instructions of Engineer ‐in ‐charge.

Repair of existing Boundary wall etc around water works compound and Tubewell complete in all respect including supply of all materials, labor, T&P etc. required for proper completion of the works upto the satisfaction of Engineer-In-Charge.

Repair/installation of Barbed wire over existing Boundary wall etc around the waterworks compound and Tubewell complete including supply of all materials, labor, T&P, etc. required for proper completion of the works upto the satisfaction of Engineer-In-Charge.

Nala (big)/culvert crossing more than 3.5m width with DI pipe including concrete encasing.

Supply and fixing of 3.6M wide gate and 1.2M wide Wicket Gate with 1.8 m height as per type design including fabrication and supply of steel and construction of RCC boundary pillars including plaster, putty,priming coat and painting etc complete as per direction of engineer in charge

Restoration of pit, trench/ Road (as site condition NON PAVED, BOE, CC, INTERLOCKING BRICKS road , RAMP, DRAIN, WALL, FLOOR etc.) as per PWD/UPJN SPECIFICATIONS after house connection.

Construction of outside toilet facilty (0.90X 1.20M inner area) in the premisis of OHT Campus including plumbing, sanitary and electric fitting, plaster, putty,priming coat and painting etc complete as per direction of engineer in charge

E&M Work

Transportation (Zone -1)

Transportation of rig machine including Loading , unloading, Erection, Dismantling & labour etc complete in all respect and watch & ward during constriction of tubewell.

Transportation of 350 psi air compressor including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

Logging of Bore

Transportation of 1 cusec/3 causec OP unit including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

CONSTRUCTION OF TUBE WELL (DRILLING)

Drilling of 500mm dia bore from G.L. to 65m BGL.

Drilling of 450mm dia bore from 65m BGL to 100m BGL.

Drilling of 450mm dia bore from 100m BGL to 200m BGL.

LOWERING OF TUBE WELL ASSEMBLY AND SHROUDING OF T.W. BY GRAVEL

Lowering of 200mm dia MSERW 7.1mm thick plain pipe from GL to 100m BGL.

Lowering of 200mm dia MSERW plain/slotted pipe 7.1mm thick from 100m BGL to 180m BGL.

TUBE WELL: ASSEMBLY

200mm dia size MSERW housing pipe minimum 7.1mm thick including 1 No M.S. well cap 12mm thick , M.S. ring 12mm thick, M.S. clamp ,T.W. Support (I Section),bail plug, center guide etc comp in all respect . (As per IS 4270, IS 8110)

DEVELOPMENT OF TUBE WELL

Development of tube well by 350 PSI air compressor

PEA-GRAVEL

1.60mm to 4.80mm size pea-gravel of Lalkuwan quarry duly screened, washed and proper stacking at site.(As per IS 4097)

Development of tube well by 1 cusec O.P. Unit.

Estimate for DMA Equipment At OHT Zone 4

Transportation of rig machine including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

SITC of Motor operated Actuators with sluice valve 300 mm dia (DMA-1)

O.P. UNIT

SITC of Motor operated Sluice valve 250 mm dia at (DMA-2)

TRANSPORTATION (Zone -3)

Logging of Bore

Transportation of 1 cusec/3 causec OP unit including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

CONSTRUCTION OF TUBE WELL (DRILLING)

Drilling of 500mm dia bore from G.L. to 65m BGL.

LOWERING OF TUBE WELL ASSEMBLY AND SHROUDING OF T.W. BY GRAVEL-

Drilling of 450mm dia bore from 100m BGL to 200m BGL.

LOWERING OF TUBE WELL ASSEMBLY AND SHROUDING OF T.W. BY GRAVEL

Lowering of 200mm dia MSERW 7.1mm thick plain pipe from GL to 100m BGL.

Lowering of 200mm dia MSERW plain/slotted pipe 7.1mm thick from 100m BGL to 180m BGL.

Transportation of 350 PSI AIR COMPRESSOR including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

Transportation of 1 cusec op unit including Loading , unloading, Erection, Dismantling & labour etc complete in all respect .

DEVELOPMENT OF TUBE WELL

Development of tube well by 350 PSI air compressor

CONSTRUCTION OF TUBE WELL (DRILLING)

PEA-GRAVEL

1.60mm to 4.80mm size pea-gravel of Lalkuwan quarry duly screened, washed and proper stacking at site.(As per IS 4097)

Development of tube well by 1 cusec O.P. Unit.

Survey site Investigation Planning , design Drawings, excavation, dismentaling, road restoration & other all utility restoration( as per required) as per NATIONAL HIGHWAY standard as per MORTH Road manual and vetting / checked from State Road/ NH DIV. PWD/NHAI/UPSHA/ PWD/ Divisional Office and taking NOC CHARGES.(incl. noc fees, licence fees, security amount) for trenchless crossing of National highway road , Road for required dia Rising main pipe with casing pipe as required for proper completion of work also including security money deposited to Road department and Execution of all work in the present of Road staff / Engineers including of supply of required dia MS carrier pipe and required size of MS casing pipe as per drawing and as per (IS:3589 & made from confining to IS:2062) with 750 Micron th. food grade coating internally and 750 MM TH. MICRONE anti corrosive bituminous paint externally by trenchless technology method at an average depth 3.60 mtr from normal ground level up to top of casing pipe including excavation & sand filling of Pit, Dewatering arrangement, Supporting system for soil, also including supply and fixing of 2 no Sluice valve ISI Mark, construction of sluice valve chamber etc. all complete work including supply & fixing specials in carrier pipe over main pipe, as per specification given in the bid documents including supply of all materials, labour T&P etc. for proper completion of work as per instruction of Engineer. and concerned department. (CASING- 600MM (id) MS PIPE 12 MM THICK & CARRIER PIPE- AS PER REQUIRED DESIGN) INCL.3M C/C SPACER.

Chemical and bacteriological test of water sample from departmental approved lab.

MAIN PIPING AND VALVES:

SITC of 550 LPM, 107/111 meter head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

Ratting of Soft starter should be one rating

Motor Operated Actuator with Sluice Valve (100mm)

higher than the required capacity with RS 485 Part-400V Class.

SITC of 100mm dia size main piping, NRV, Sluice valves, CI D/F band, Tee, pipe etc with 24 mtr column pipe, Automatic chlorination system (SCADA compatible), power wiring, earthling, painting, tool set, wiring of pump house, chain pulley block and gauges complete in all respect with all required material, T& P labour.

CE / UL certified Electromagnetic flow meter of size:100mm /Suitable size

SITC of Scada compatible servo voltage stabilizer of 2x HP of motor rating input, output voltage data transfor to Scada ( as per instruction of engineer in charge) with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthling etc complete in all respect.

Chemical and bacteriological test of water sample from departmental approved lab.

MAIN PIPING AND VALVES:

PUMP SET:

Motor Operated Actuator with Sluice Valve (80mm)

400 LPM, 106 meter head 1450rpm,submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling control panel etc.

SITC of 100mm dia size main piping, NRV, Sluice valves, CI D/F band, Tee, pipe etc with 24 mtr column pipe, Automatic chlorination system (SCADA compatible), power wiring, earthling, painting, tool set, wiring of pump house, chain pulley block and gauges complete in all respect with all required material, T& P labour.

SITC of 80mm dia size main piping, NRV, Sluice valves, CI D/F band, Tee, pipe etc with 24mtr column pipe, Automatic chlorination system (SCADA compatible), power wiring, earthling, painting, tool set, wiring of pump house, chain pulley block and gauges complete in all respect with all required material, T& P labour.

Spare 3.0 Mtr Long Heavy duty Column pipe 80 mm Size

CE / UL certified Electromagnetic flow meter of size:80mm /Suitable size

Trial run

Chemical and bacteriological test of water sample from departmental approved lab.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 01 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

PUMP SET: (Zone 2)

Motor Operated Actuator with Sluice Valve (100mm)

600LPM, 81m/79m head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

SITC of 100mm dia size main piping NRV, Sluice valves, CI D/F band, Tee, pipe etc with 24 mtr column pipe, Automatic chlorination system (SCADA compatible), power wiring, earthling, painting, tool set, wiring of pump house, chain pulley block and gauges complete in all respect with all required material, T& P labour.

Spare 3.0 Mtr Long Heavy duty Column pipe 100 mm Size

1.60mm to 4.80mm size pea-gravel of Lalkuwan quarry duly screened, washed and proper stacking at site. (As per IS 4097)

Development of tube well by 1/3 cusec O.P. Unit

Chemical and bacteriological test of water sample from departmental approved lab.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 01 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

PUMP SET: (Zone 2)

Motor Operated Actuator with Sluice Valve (100mm)

600LPM, 81m/79m head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

SITC of 100mm dia size main piping NRV, Sluice valves, CI D/F band, Tee, pipe etc with 24 mtr column pipe, Automatic chlorination system (SCADA compatible), power wiring, earthling, painting, tool set, wiring of pump house, chain pulley block and gauges complete in all respect with all required material, T& P labour.

Development of tube well by 1/3 cusec O.P. Unit.

CE / UL certified Electromagnetic flowmeter of size:100mm /Suitable size

SITC of Scada compatible servo voltage stabilizer of 2x HP of motor rating input, output voltage data transfor to Scada ( as per instruction of engineer in charge) with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthling etc complete in all respect.

Chemical and bacteriological test of water sample from departmental approved lab.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 02 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

Excavation for pipeline trenches in ordinary soil (loam,clay or sand) including lift upto 1.5m and lead upto 50m and refilling, watering, ramming of excavted earth in to the trenches including reinstatement of damaged underground and overhead utilities and disposal of surplus earth upto 8 Km. from the center of the trenches. D.I.( K-9) pipes

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 01 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

decomposed/soft Rock and replace of ordinary soil.

Motor Operated Actuator with Sluice Valve (100mm)

600LPM, 81m/79m head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

PUMP SET: (Zone 4)

600LPM, 71/74 Meter head (both tentative) 1450rpm, submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989),with cable ,earthling, control panel etc.

500LPM, 71 Meter head 1450rpm, 15 H.P. submersible clear water pumping plant suitable to operate on 415+ %5 volt, 50 Hz, 3 phase A.C. supply (as per IS 8034-1989)

CE & BIS approved manufacturer's industrial grade LCD monitor with latest configuration as per specification of size 65"

SITC of Scada compatible servo voltage stabilizer of 2x HP of motor rating input, output voltage data transfor to Scada as per instruction of engineer in charge) with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthling etc complete in all respect.

Trial run of pumping plant and all other E&M / Automation equipments installed at tubewells and ESR of Zone- 04 with Electricity, Chlorine, & Operation charges till hand over of scheme to concerning ULB.

Scada Master Control Station (MCS)

Desktop/PC with i7 processor for as per spec mentioned in technical bid documents 01 for mcs room & other 01 for monitoring at Jal nigam office.

GSM based wireless / broadband/Equipment communication system for PLC capable to transfer and gather data from remote sites to control stations, including all accessories complete

CE/UL approved manufacturer's Firewall for network protection

CE/UL approved manufacturer's suitable size UPS with batteries as spec. mentioned for STP and Computer as per requirement

Full development version of required TAGS SCADA Software with customization of software for MCS as per required as per spec mentioned in technical bid documents.

Mobile App facility system architecture complete.

Supply and Installation 1.5 Ton AC with stabilizer and other required item for installation

Canon/HP 1018/equivalent Laser printer with chair and table.

CE/UL certified field gateway agent for transferring data from MCS to control room

Installation, testing and commissioning with required furniture,Air Conditioner etc

Test and trial run

Lightning surge protector for Ethernet communication protection

CE & UL approved manufacturer’s RTU/ PLC in IP 65 encloser suitable to communicate with GSM based modem unit with CPU and power supply with analog and digital parameter and features as specified, one for each tubewell to store and transmit data on GSM backbone. RTU/PLC designed with logic to transfer data at multiple stations

CE/UL approved manufacturer's industrial grade Ethernet switch

CE / UL certified Intelligent smart energy meter

Security Surveillance IP camera

UNIT ESTIMATE of SCADA for TUBEWELL

CE / UL certified Pressure Transmitter

CE / UL certified Surge protector for control panel

G.S.M./G.P.R.S. based wireless communication with 4G Modem for RTU/ PLC Capable to transfer and gather data from remote sites to control stations, all accessories included with signal enhancer antenna made for pumping plant

Auto phase reversal unit with inbuilt time delay & enclosure conforming to IEC: 60947-1 & IEC:60947-b-1) 200Amp

Control panel with IP 54 protection, industrial grade fro all equipments (separate for control (24V) and power equipments.

Installation, commissioning & testing

CE / UL certified Hydrostat tic type sub soil water level transmitter for Tubewell.

Complete Cabling for tubewell including all power & control cables of all equipment at pump house and OHT

CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each tubewell/ OHT & stand alone OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations

CE/UL approved manufacturer's industrial grade Ethernet switch

Test and trial run for 3 Months period (3x10 Nos tubwell)

Estimate for DMA Equipment At OHT Zone 1,

CE & UL certified Radar type level transmitter for OHT

CE/UL Certified pressure Transmitter

Motor operated Actuators for existing valve already fitted in OHT feeder line by civil department

SITC of Motor operated Actuators with sluice valve 250 mm dia (DMA-1)

SITC of Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system .

SITC of Motor operated Actuators with sluice valve 200 mm dia (DMA-2)

Installation ,commissioning and testing .

SITC of CE & UL certified Electromagnetic Flowmeter for OHT line 250 mm (DMA-1)

CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each tubewell/ OHT & stand alone OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations

CE/UL approved manufacturer's industrial grade Ethernet switch

Test and trial run for 3 Months period (3x10 Nos tubwell)

SITC of CE & UL certified Electromagnetic Flowmeter for OHT line 200 mm (DMA-2)

Complete cabling of all equipment at OHT including power and control cable.

CE & UL certified Radar type level transmitter for OHT

CE/UL Certified pressure Transmitter

Estimate for DMA Equipment At OHT Zone 2,

SITC of Motor operated Actuators with sluice valve 250 mm dia (DMA-1)

SITC of Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system .

SITC of Motor operated sluice valve 200 mm dia (DMA-2)

Installation ,commissioning and testing .

SITC of CE & UL certified Electromagnetic Flowmeter for OHT line size 200 mm. dia.

SITC of CE & UL certified Electromagnetic Flowmeter for OHT line size 250 mm. dia.

CE & UL certified Radar type level transmitter for OHT

CE/UL Certified pressure Transmitter

Complete cabling of all equipment at OHT including power and control cable

SITC of Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system .

SITC of Motor operated sluice valve 200 mm dia (DMA-2)

Installation ,commissioning and testing .

Estimate for DMA Equipment At OHT Zone 3

Test and trial run for 3 Months period (3x10 Nos tubwell)

Motor operated Actuators with sluice valve at DMA-1 and DMA-2)

SITC of CE & UL certified Electromagnetic Flowmeter for OHT line size 300 mm. dia.

CE/UL Certified pressure Transmitter

Complete cabling of all equipment at OHT including power and control cable

SITC of Motor operated Actuators with sluice valve 250 mm dia (DMA-1)

SITC of Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system .

SITC of Motor operated sluice valve 200 mm dia (DMA-2)

Installation ,commissioning and testing .