Construction of Office Building at District Head Quarter Jaipur for Tribal Area Development Department (Electric work - CCTV, PA system, Projector, Intercom, etc.

Amount

SITC of IP 67, IK 10, full HD 1920*1080, 20-60 fps, 2 MP, ONVIF profile S/profile G, True day/night, Bullet camera having wide dynamic range up to 120 dB 2.7-12mm Varifocal lens with 16X digital zoom, S/N ratio 50-60 dB, Provision of Auto/manual white balance, gain control & on board micro SD card support, IPv6 ready, Supports all standard protocols, operating temperature range of 20 degree celcius to 50 degree celcius. The work includes complete installation, outdoor weather proof camera enclosure, mounting brackets, clamps etc. required for successful operation of system of make BOSCH/ Honeywell / Sony.

SITC of IP 67, IK 10, full HD 1920*1080, 20-60 fps, 2 MP, ONVIF profile S/profile G, True day/night, Dome camera having wide dynamic range up to 120 dB 2.7-12mm fixed lens with 16X digital zoom, S/N ratio 50-60 dB, Provision of Auto/manual white balance, gain control & on board micro SD card support, IPv6 ready, Supports all standard protocols, operating temperature range of 20 degree celcius to 50 degree celcius. The work includes complete installation, outdoor weather proof camera enclosure, mounting brackets, clamps etc. required for successful operation of system of make BOSCH/ Honeywell / Sony.

SITC of network video recorder of 32 channel HD recording, user friendly operation with features to view record, playback, live view and remotely control the system simultaneously with 4 SATA interface to support 04 TB HDD, 19PoE, VGA output, HDMI, multiscreen display of 1/4/8/16 windows, Ethernet LAN with RJ-45 connector of make, Samsung/Sony/ Honeywell.

SITC of high performance 4 TB surveillance Hard Disc Drive to be fitted in existing NVR of make Western Digital (WD)/Seagate.

Supply, installation & commissioning of Smar LFD signage display of screen size : 55'' (138 cm diagonal), in built two speakers, LED backlit type, wall/ table mount type of following specifications with making connectivity of devices with surveillance system with the help of signal/ 2 mtr. HDMI cables as required along with all accessories : SONY/LG/SAMSUN/ BARCO/ NEC/ PANASONIC Make)

Resolution : 1920*1080 (16:9) FULL HD

Brightness : minimum 450 nit

Scree type : Non touch

Duty Cycle : 24*7

Viewing angle : 178:178

Power : AC 100-240v 50 HZ

SITC of Wireless Access Point consisting of following specifications

Supported Standards: 802.11 a/b/g/n/ac; Wave 2 Concurrent Dual-band 2.4 & 5 GHz

Supported Data Rates: 802.11b: 1, 2, 5.5, 11 Mbps, 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps, 802.11n: 6.5 – 144 Mbps (20 MHz), 802.11n: 13.5 – 300 Mbps (40 MHz), 802.11ac: 6.5 – 173.4 Mbps (20 MHz), 802.11ac: 13.5 – 400 Mbps (40 MHz), 802.11ac: 29.3 – 866.6 Mbps (80 MHz)

Access Point should be Dual Radio capable. Access Point radio should have minimum 2X2 radio chains MIMO with minimum 2 spatial streams for each band

Channelization: The AP should support 20/40/80 MHz channel width.

ESSIDs: Up to 16 SSIDs per radio (32 total) available on each AP simultaneously without negatively impacting system performance

It should provide physical data rate of up to 300 Mbps for 2.4 GHz and up to 867 Mbps for 5 GHz which makes aggregate data rate capability of up to 1.2 Gbps

Supported concurrent users per AP should be up to 256 combining both the bands

Power: Should have option for both, 12V 1.0A DC input and 802.3af PoE compliant with maximum power consumption of 9W.

Interfaces: 1 Gigabit 802.3at PoE Uplink and 1 Gigabit 802.3af PoE LAN ethernet interface with the Auto-MDIX capability to make sure two end stations are connected using crossover cable to make sure correct pairs are connected. 1 USB interface that can transmit data rate at a maximum rate of 480 Mbps.

The AP should have LED indicators for Power / 2.4G-WiFi / 5G-WiFi / Eth1 / Eth2

The AP should have reset/restart button(s)

Environmental Conditions: The Access point shall be rated for operation over a temperature range of 0° to 50°C and operating humidity of 5% to 95% (Non condensing).

Antennas

AP should have option for, Option 1: Built-in 2.4GHz 5dBi Omni, 5GHz 15dBi Directional with Azimuth 30° & Elevation 20° Option 2: Built-in 2.4GHz 10dBi Directional with Azimuth 130° & Elevation 30°, 5GHz 10dBi Directional with Azimuth 90° & Elevation 30°.

The Ap should have 3 x Built-in PIFA (2 x 2.4 GHz, 5 GHz, 1 x Bluetooth Low Energy) with antenna gain 3 dBi (2.4 GHz), 5 dBi (5 GHz), 3 dBi (BLE).

The AP should be Wall/Ceiling mount with Mounting kit included.

Quality of Service (QoS): The Ap should support following QoS

Wireless QoS (802.11e/WMM) DSCP (802.1p) Airtime Fairness Band Steering Multicast to Unicast Conversion Optimal Client Filtering

Security:

Wireless Security: WEP, WPA / WPA2 Mixed (TKIP/AES Mixed), WPA2-Personal (AES), WPA2-Enterprise (AES)

The AP should support VLAN Tagging (802.1Q)

Station isolation

Support for DHCP Snooping

The AP should have L2 firewall in it.

Management

Deployment: The AP deployment should be in standalone, hardware or cloud controller managed and tunnel managed by controller with IPv4 and IPv6 compatibility. Deployment option for LLDP to advertise a device's identity and abilities, as well as other devices connected within the same network.

Configuration: SNMP v1/v2c/v3 and web user interface (HTTP/HTTPS)

Mobility/Roaming

Layer2/Layer3 fast roaming.

Hotspot 2.0

Certificates: FCC (United States), CE (Europe), WPC (India) certified.

Wireless Access point and wireless controller should support seamless integration

Field deployment shall be with EIRP as per regulatory guidelines

Make: Edgecore/Cisco/Alcatel

Supply,Installation,Testing and Commissioning of Wireless Centralized Controller to provide maximum flexibility, manageability and preserve technology investments, the provided solution should be via a single integrated console with an on-premise centralized hardware controller. The provided controller should be separate hardware and not the wireless access point having following specifications.

System Capacity: System should be able to manage up 50 APs, up to 2000 local accounts, up to 2000 on-demand accounts and 200 concurrent users (switchable).

Hardware Specifications

Form Factor: The provided hardware controller should be desktop mount.

Interfaces: 1 Gigabit WAN/Uplink and 4 Gigabit LAN ethernet interfaces with the Auto-MDIX capability to make sure two end stations are connected (or two controllers are connected) using crossover cable to make sure correct pairs are connected. 1 USB interfaces that can transmit data rate at a maximum rate of 5 Gbps each. Support for 1 RJ-45 console interface. All the ports must be active from day one.

The hardware controller should have LED indicator for power & status and also a reset button.

Environmental Conditions: The Access point shall be rated for operation over an ambient temperature range of 0° to 40°C and RH 5% to 95% (Non condensing)

Power: Should support DC Input: 12V / 1A with Power Adapter Included

User Security

Authentication: 802.1X with encapsulation of the Extensible Authentication Protocol (EAP) over IEEE 802 which is known as "EAP over LAN" or EAPOL. UAM to allow a subscriber to access and login to services with just a Wi-Fi network interface and Internet browser on the user's device. IP or MAC-based authentication support.

Authentication Servers: The hardware controller should have support for integrated or external Local, On-demand, Guest, RADIUS to enable access servers to communicate with a central server to authenticate dial-in users and authorize their access to the requested system or service, Lightweight Directory Access a client/server protocol to access and manage directory information read and edit directories over IP networks and runs directly over TCP/IP using simple string formats for data transfer, NT Domain, SIP, POP3.

Customizable Captive Portal and Wild Card Walled Garden

User Blacklisting

Account Generation: The controller should have the capability to generate the following accounts

Account Generation: SMS registration. Purchase via PayPal and integration with third party payment gateways. PMS integration in partnership with SMS API, Clickatell. Scalable billing plans. Account ticket printer.

On-demand Account Flexibility: Customizable Billing Plans. Account Credentials. Access Codes. Smart Login

Guest Wi-Fi Account: Limitation by duration and volume. Configurable reactivation time. E-mail registration and activation. Social Media Login

Network Security: The admin should be able to configure following network securities in the hardware controller:

The admin should be able to configure following network securities in the hardware controller:

Remote access via VPN with site-to-site VPN to establish secure connections between main and branch locations. IPSec and PPTP tunneling protocols. Inter/Intra-VLAN or Port-based network isolation. Rogue AP Detection. Built-in root CA certificates.

Network Services

As a wireless network will be used by the university, it is crucial to take into consideration fundamental network services such as DHCP, NAT, and dynamic routing. In addition to providing these functions, the controller also must implement the concept of a "Service Zone", which essentially segments the controller into multiple virtual controllers, each with its own associated network services, user policies and authentication settings.

On the reliability end, the hardware controller must support WAN port failover. Furthermore, load balancing between the WAN ports to increase overall performance by alleviating congestion and distributing traffic between the two outgoing links.

Redundancy: 1+1 HA: When the active controller malfunctions, the standby controller will take over, the new active one will take on all the settings of the previous active controller. N+1 HA: The standby controller can be the backup for either one of multiple active controllers.

The controller should support IPv4 and IPv6 internet protocols.

High performance content filter HTTP proxy server to examine web traffic to identify suspicious content, which can be a spyware, malformed content, or another type of attack.

Local DNS Records

Integrated Billing & Accounting System

Billing Quota Types: By duration; By Traffic Volume

PMS Integration: Innkey PMS, Oracle hospitality Opera ( Micros Opera PMS), IDS next.

System Management

As the controller will be the central point of management for network administrators. The management console of the controller should be a browser-based GUI which should be simple and intuitive to operate. The controller should have a feature to generate administrator accounts for multiple tired access privileges and the admin must be able to Monitor each admin’s current accessed page.

Ability to set system time by NTP synchronization and manual configuration.

From the controller interface, network administrators must be able to configure traffic shaping profiles, track previous network usage, crapture backup (built-in) perform system backup and restore.

AP Management

Centralized AP configuration and monitoring to reduce maintenance overhead.

The controller must support automatic AP discovery, AP provisioning with template-based AP provisioning.

The controller must support automatic AP configuration back and restore.

Automatic and secure AP firmware batch upgrade.

Tunneled AP Management for both L2 & L3 APs.

AP load-balancing feature with automatic adjust AP transmit power to balance loading.

Automatic and secure AP Firmware Upgrade

Automatic Periodically AP Backup

Switch Management

The controller must support automatic switch discovery, switch provisioning with template-based switch provisioning.

The controller must support automatic switch configuration back and restore.

Support for switch power scheduling

User Management: The controller should support user policies which consist of the following.

Role-based, time-based and location-dependent user policy assignment should be supported by the controller

The controller should be able to limit user-based, group-based bandwidth and must support bandwidth throttling.

Traffic Classification / Remarking / QoS: Yes; 802.1p, DSCP

Stateful firewall where admin can create each rule with individual enforcement schedules.

Routing policy with static route assignment

Concurrent session limit and idle timeout

Allow clients to obtain different IP addresses after authentication as IP Address reassignment

Device/User Mobility

Layer 2 Roaming: Layer 2 Roaming: Users should be able to roam between different APs without getting disconnected.

Cross Gateway Roaming: Cross Gateway Roaming: Users should be able to roam seamlessly between APs managed by different controllers.

Account Roaming Out: Account Roaming Out: Users should be able to roam between different APs from other controllers with their original local user accounts.

WISPr Smart Client Roaming: The controller should support features to enable client authentication and provide client roaming between internet service providers.

The controller should support mobile device Recognition for optimized captive Portal.

The controller should support multiple device logins per account.

Support for QR code automatic login.

Support for device plug-and-play.

Support for on-demand smart login without re-authentication

System & Network Status

System Dashboard

Graphical System Performance Reports

Traffic Volume Reports

System Process Monitor

Online Device Monitoring

Active Sessions List

Configurable SYSLOG Severity

SMTP (E-mail) Notifications

Multiple Concurrent E-mail Notification Receivers

Network Activity Logs

Detailed user events and traffic logs to help network administrators monitor user activity and troubleshoot network issues. Logs and reports must be exportable to external SMTP/ SYSLOG/FTP servers.

Need to be able to identify users who are violating network policies using the following logs: NAT log: To help trace the public IP/port to private IP/port conversion User event log: search by IP address for users to find when the user authenticated and from which AP Example logs & reports: User browsing history, User event log, NAT log, On-demand billing report, regular system report.

Logs for Control and provisioning of wireless access points to enable a central wireless Controller to manage a collection of wireless access points.

Logs for change of the configuration

The server log file which records RADIUS events, such as server startup or shutdown or user authentication or rejection, as a series of messages in an ASCII text file. Each line of the server log file should identify the date and time of the RADIUS event, followed by event details.

User HTTP web logs

Make: Edgecore/Cisco/Alcatel Or Any Approved Make as per engineer incharge

SITC OF IP Based Ceiling /Wall Mount Speaker WITH FOLLOWING SPECIFICATIONS:

Power Supply : POE

Power Consumption:12W

Internet Port: RJ 45

Transmission Speed : 10/ 100 Mbps

Support Agreement : TCP/ IP, UDP, IGMP

Audio Format: MP3/MP2

Audio Mode : 16 bit CD sound quality

Sampling Rate: 8K~48K

Bit Rate: 8K~512Kbps

Rated Power : 8W

Max Power : 10 W

Sensitivity: 92dB (+/- 3dB)

Response Frequency: 80Hz~16KHz

Speaker Driver : 6.5" x 1

Make: Audiotrack/Honeywell/Bosch Or Any Approved Make as per engineer incharge

SITC of IP Based Intercom Call Station with Following Technical Specifications:

Network Input :Standard RJ45

Communication Protocol :TCP/IP, UDP, IGMP (multicast)

Audio Format: MP3/MP2

Sampling Rate: 8K~48KHz

Transmission Speed : 100Mbps

Audio Mode : 16-bit stereo CD sound quality

Screen Size :7 inch

Screen Resolution : 800 x 480 pixel

Screen Type : 65 k color DGUS screen

Keyboard Types : Virtual QWERTY keyboard

keyboard Entry Method : Resistive Touch

Rated Power and Impedance of Built-in Speaker : 4Ω, 2W

Frequency Response : 80Hz~16KHz

S/N Ratio : >68dB

Make: Audiotrack/Honeywell/Bosch Or Any Approved Make as per engineer incharge

SITC of Desktop Computers for IP PA System,CCTV System,Wireless AP System having following Technical Specifications:

Processor : i5 and Above

RAM: 8GB and Above

HDD: 4TB

Screen: 21" Inch, Windows 10 OS, MS Office 360

Keyboard,Mouse

Make: HP/Dell/Lenovo/Acer Or Any Approved Make as per engineer incharge

SITC of IP PA Controlling Software having folllowing Technical specifcations

Software should Support Windows 10 and above

Full Duplex Communication Software

Can Control 9 Priority Levels

Built In Decoder to transfer Analog Signal to Digital Sound Card

Built in Weekly timer to Program Music or Sound Files to timely

broadcast at designated zone at pre defind time

Display to monitor each unit

Customize Zone wise paging

Make: Audiotrack/Honeywell/Bosch Or Any Approved Make as per engineer incharge

SITC of steel body evaporative room cooler of superior quality having ISI fan motor of 450mm sweep & 3000cubic mtr/hr with aluminium blade & ISI marked submersible pumpset of high quality,15 mm wood wool pads of high quality,60 ltr water sump tank capacity & tank sheet thickness of 1.0mm.The cooler body shall be made of galvanized sheet steel not less than 0.8mm thick.There shall be three speed fan regulator with on/off switch for fan & pump .The main cord of 2.5 mtr length of 2.5sqmm cable along with suitable plug top & water inlet float valve complete in all respect with mounting stand..Kit Brand: POLAR/Khaitan/Crompton/GEC Or Any Approved Make as per engineer incharge

Supply,Installation,Testing and Commisioning of multimedia projector of brightness 3800 lumens or more, image brightness not less than 3800 ANSI lumens,Resolution 1280*800(WXGA) ,standard throw (0.91 to 2.5m) with 120 % optical zoom,Aspect ratio of 16:9 ,ultra high pressure mercury lamp/UHE/UHM source(minimum life of source 6000 hrs),HDMI ports,audio & video ports & all standard ports along with ceiling mounting kit having trolley base ,240 V ,50Hz supply operated complete in all respect of SONY/BENQ/EPSON/HITACHI Or Any Approved Make as per engineer incharge

Supply, installation,Testing and Commissioning of superior quality wall mount motorised screen of size 100 inches diagonal (152.4*203.2 cm),HD matte white fabric with anti UV coating,complete with suitable rating silent single phase electric motor,wired or wireless remote with batteries, wall mounted clamps etc as required to operate on 240V,50Hz power supply. Make: Suvira/Brix/Logic Or Any Approved Make as per engineer incharge

SITC of 86Inch Interective Screen Panel with following technical specifications:

Display Type: LCD

Display Size (in.):86 Inch

Viewable Area (in.):85.6 Inch

Light Source:LED

Resolution:3840 x 2160

Refresh Rate (Hz):60

Aspect Ratio: 16:09

Static Contrast Ratio:1,200:1

Dynamic Contrast Ratio:5,000:1

Backlight Life (Hours):50000

Brightness:350 cd/m2

Response Time (Typical GTG):8ms

Viewing Angles:178º horizontal, 178º vertical

Panel Surface:9H

Operation Rating:16/7

Networking:

Ethernet LAN:10/100/1000 Mbps

Embedded Player:

OS:ViewBoard OS (embedded Android 8)

CPU:ARM Quad Core A73 + A53

CPU Processor Speed:A73: 1.1GHz, A53: 1.5GHz

Memory:3GB

Storage:32GB

Audio:

Internal Speakers:10W (x2)

Subwoofer:15W (x1)

Connector:

HDMI 2.0 In(3), HDMI Out(1), VGA(1), 3.5mm Audio In(1), 3.5mm Audio Out(1), SPDIF Audio Out(1), USB 3.0(4), USB 2.0(3), Slot-in PC Slot(1), USB B Touch Port(2), RS232(1), Ethernet LAN (RJ45)(1), WIFI Module Slot(1)

Power:

Voltage:100-240 VAC

Consumption (max):350W

Consumption (typical):155W

Operating Conditions:

Temperature:32-104º F (0 - 40º C)

Humidity (non-condensing):10-90%

Touch:

Touch Technology:Infrared

Touch Points:20-Point Touch

Tip Detection:Dual tips, 3mm and 8mm

With Mounting Kit Stand

Make: Viewsonic/Panasonic/Samsung Or any make approved by engineer incharge

Supply, installation, testing & commissioning of Wireless Handheld Microphone -Modulation -wideband FM,Switching bandwidth up to 24 MHz. Frequencies 8 frequency banks, each with up to 10 factory-preset channels .Signal-to-noise ratio ≥ 103 dBA,THD ≤ 0.9% ,Temperature range operation: 0°C to +40°C storage: –20°C to +70°C,Transmitter sychronization 2.4 GHz, Low Power OQPSK (only active during synchronization),AF frequency response 50 to 16,000 Hz (–3 dB),Line/Mic level 20 dB, switchable,Housing material rugged ABS ,RF output power 10 mW,Pick-up pattern cardioid.. Makes- Sennehiser/Bayerdyanmic/Televic/EV or any make approved by engineer incharge

Supply, installation, testing & commissioning of Wireless Lapel Microphone Modulation -wideband FM,Switching bandwidth up to 24 MHz. Frequencies 8 frequency banks, each with up to 10 factory-preset channels .Signal-to-noise ratio ≥ 103 dBA,THD ≤ 0.9% ,Temperature range operation: 0°C to +40°C storage: –20°C to +70°C,Transmitter sychronization 2.4 GHz, Low Power OQPSK (only active during synchronization),AF frequency response 50 to 16,000 Hz, Audio Input 3.5 mm jack socket,Housing material rugged ABS ,RF output power 10 mW,Pick-up pattern - omni-directional..Operating time approx. 10 hrs. Makes- Sennehiser/Bayerdyanmic/Televic/EV or any make approved by engineer incharge

Supply, Installation, Testing and Commissioning of Digital Signal Processer (DSP) having following technical specifications:

The audio DSP shall support Audio Video Bridging (AVB) digital audio networking that shall allow up to 128 x 128 channels. The AVB networking connection shall be implemented on a RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on a RJ-45 connector. The audio DSP shall have internal DSP processing. The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for sending or receiving logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a RS-232 connection for control data transmission into or out of the audio DSP and such operation shall be software programmable. The audio DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and output. The audio DSP shall provide 4 balanced input connections for receiving of microphone or line level analog audio signals on screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware and firmware, the parameters, routing and operation of which shall be software programmable.

The audio DSP shall provide 4 balanced output channels for the transmission of microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel shall have its own dedicated connection. The audio DSP shall integrate to Voice Over Internet Protocol (VoIP) systems on a RJ-45 connector for two lines of VoIP communication and shall support Session Initiation Protocol (SIP) v2.0 or later. The audio DSP shall integrate to standard telephony communications on a RJ-11 connector for a single line of telephone communication. The audio DSP shall provide front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy all Tesira expander-class devices and Tesira control devices. The audio DSP shall be CE marked, UL listed, and shall be compliant with the RoHS directive. Makes- Biamp/Polycom/Symentrix or any make approved by engineer incharge

SITC of 4K60 Simultaneous Wired and Wireless Presentation and Collaboration Solution Wireless presentation device allows users with laptops or mobile to connect and present. Should have 4K@60 HDMI Wired Input to connect a source with HDMI directly. Should have 1 HDMI (Supports 4K video resolution) & 1 DisplayPort (Supports 4K video resolution) outputs. Should have one Gigabit LAN Ethernet port. Should have audio embedding feature with 1 unbalanced stereo audio (line or mic) input on a 3.5mm jack. Should have audio de-embedding feature with 1 Analog audio line out on a 3.5mm jack. Wireless Connection for up to 254 user devices. Should present minimum 6 users laptops or handheld devices on a single display or 12 users on two displays at a time. Should be capable of replicating any iOS device without any required app/device. Should have 2 nos. USB 3.0 & 2nos. of USB 2.0 port for connecting peripheral devices like Webcam, Microphone, Speakerphone, keyboard & mouse.Should be able to share wirelessly uninterrupted video with resolution support of 4K@60Hz. Should have a feature to stop someone else from presenting to enable uninterrupted presentation. Should have annotation & white board feature on both wired & wireless source connected. Should provide a participant control over a presenter’s PC for true collaboration.

Should have DHCP support. Should have inbuilt/external Wi-Fi. Should have feature to call the output view of the wireless presenter on any of the connected devices for viewing or doing annotation. Should have file sharing & chat options for all participants. Should have minimum 128GB (SSD) inbuilt memory, 8GB RAM, 3.60 GHz quad core (8th Generation) processor. Should have file viewing/downloading option from inbuilt memory. Should have Room Calendar Integration which shows the room occupancy schedule on the main display. Should have functionalities of instant Emergency Message/Alert messages for immediate push to the main display. Should have feature of Stream all collaboration activity from the main display to any H.264 decoder. Should have recording feature which an entire VIA video and audio session to a local video file.

It should have facility to Load third party software to use the device a VC Codec, any third party software which supports Windows 10 OS can be installed by user easily. Powerful security features: user authentication, 1024–bit encryption, dynamic room code, Remote Power Control - via a relay port. Required Certification: CE, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment maybe added to match the complete specs. Makes- Kramer/Extrron/Lightware or any make approved by engineer incharge

Supply, Installation, Testing and Commissioning of Power Amplifier having following Technical Specications:

The amplifier shall be capable of being mounted in a standard 19-inch equipment rack and will take up 1 rack units in height with a maximum built in depth of 239mm/9.41 inches The amplifier shall include an output transformer per channel with a high impedance dynamic output power of at least 2 x 120 watts and low impedance dynamic output power of at least 2 x 60watts at 8ohms and include output connectivity at 100 -70 - 50 - 35 volts - 4 ohms The amplifier shall be convectional cooled and use class-D amplifier technology The frequency response of the amplifier shall be at least 50 - 20 kHz .The amplifier shall include protection against high temperature, short circuit, dc, input overload and over current The amplifier shall have a bridging function giving a total power of at least 240 watts at 8 ohms and 240 watts at 100v The amplifier shall incorporate toroidal outputs transformers to ensure reliable and safe operation .The amplifier shall include rear mounted input gain controls and clip leds along with front mounted mute controls and indications of bridge mode on, signal present, mute, limit and clip/overload. Makes- Biamp/L-Acoustic/Renkus-Heinz any make approved by engineer incharge

Supply, Installation, Testing and Commissioning of Coulmn Speakers with following Technical Specifications:

The loudspeaker shall be suitable for mounting on wall or ceiling and include a 4 x 2 inch/4 x 50.8 mm driver and a 1 inch/25.4 mm tweeter in a 2-way design with coated paper woofer material and an IP rating of IP66. The loudspeaker shall include a transformer with multiple taps of 20 - 10 - 5 watts at 100v and 20 - 10 - 5 - 2.5 watts at 70v. The loudspeaker shall have a dynamic power of at least 30 watts and the low impedance connection shall present a load of 8 ohms to the amplifier .The output sound pressure level at a distance of 1m with 1watt input level applied shall be at least 88 dB .The maximum output sound pressure level at a distance of 1m with full power applied shall be at least 100 dB .The loudspeaker shall have a frequency response of at least 250 - 20KHz, have a main construction material of aluminium with aluminium grille and will be available in white colour .The loudspeaker shall have a supporting GLL file which can be used with acoustic simulation software.

The GLL file will support Ease , EASE Focus and EASE Address software packages. The dimensions of the loudspeaker will be 400 x 66 x 66 mm/ 15.75 x 2.6 x 2.6 inches Makes- Biamp/L-Acoustic/Renkus-Heinz any make approved by engineer incharge

Supply, Installation, Testing and Commissioning of wall mount Speakers with following Technical Specifications:

The loudspeaker shall be suitable for mounting on wall or ceiling and include a 5.25 inch/133.35 mm driver and a 1 inch/25.4 mm tweeter in a 2-way design with coated paper woofer material and an IP rating of IP40. The loudspeaker shall include a transformer with multiple taps of 30 - 15 - 6 - 3 watts at 100v. The loudspeaker shall have a dynamic power of at least 80 watts and the low impedance connection shall present a load of 16 ohms to the amplifier .The output sound pressure level at a distance of 1m with 1watt input level applied shall be at least 88 dB .The maximum output sound pressure level at a distance of 1m with full power applied shall be at least 107 dB .The loudspeaker shall have a frequency response of at least 70 - 20KHz, have a main construction material of ABS plastic with steel grille and will be available in black / white colour .The loudspeaker shall have a supporting GLL file which can be used with acoustic simulation software. The GLL file will support Ease , EASE Focus and EASE Address software packages. The dimensions of the loudspeaker will be 260 x 170 x 180 mm/ 10.24 x 6.69 x 7.09 inches A u mount bracket shall be included as standard Optional brackets to allow mounting of the loudspeaker to a light rail shall be available. Makes- Biamp/L-Acoustic/Renkus-Heinz or any make approved by engineer incharge

Supply, Installation, Testing and Commissioning of Conference PTZ Camera with Following Specifications:

Resolution:4K @ 60fps

Sensor:1/2.5 inch, CMOS

Pixel:8.51M or higher

Scanning mode: Progressive

Optical Zoom : 12x or higher

Digital zoom :16x or higher

White Balance : Auto, Indoor, Outdoor, OnePush, Manual, VAR

Backlight Compensation : Supported

Digital Noise reduction ; 2D & 3D Digital Noise Reduction

Signal to noise ratio : ≥55dB or higher

Horizontal angle of view : 71° ~ 8.2°

Vertical angle of view : 42.7° ~ 4.5°

Pan Range : ±170°

Tilt Range : ±30°

H & V Flip and Image Freeze : Supported

No. of Presets : 255 or higher

System Support:Windows 7, Windows 8, Windows 10,MacOS X, Linux, Android

Encode format:YUY2 / H.264 / H.265 / MJPEG

Network Interface: 1 × RJ45

Communication Interface:1 × RS232 IN, 1 × RS485

Audio Interface:1 × LINEIN: 3.5mm Audio Interface

Video Out:1 × USB3.0, 1 × 3G-SDI, 1 × HDMI

Mounting : Wall mount, Table top

Makes- Maxhub/Vaadio/Datavideo or any make approved by engineer incharge

Supply, Installation, Testing and Commsissioning of Popup Box Should have connectivity port for HDMI, VGA, Audio and Ethernet with 2 Nos. Of Power Sockets complete in all respect with all accessories

Makes- Suvira/PAC/Stecker/Brix or any make approved by engineer incharge

SITC of USB Expander with Bluetooth having follwing technical specifications

The AVB/USB expander shall utilize an AVB/TSN network via an RJ-45 connector for audio networking as well as software configuration and control. The AVB/USB expander shall include a Universal Serial Bus (USB) 2.0 connection on a standard USB-B type connector. The AVB/USB expander shall be software configurable to stream up to 8 channels of digital USB Class 1 Audio transmission or USB Class 2 Audio transmission either into or out of the AVB/USB expander, or simultaneous input and output. The AVB/USB expander shall support Bluetooth® wireless technology and shall be compatible with the Hands-Free Profile and Advanced Audio Distribution Profile. The AVB/USB expander shall support the SBC, mSBC, and AAC codecs.

The AVB/USB expander shall support the Qualcomm® aptX™ codec. The AVB/USB expander shall be powered by PoE (IEEE 802.3at Class 2). The AVB/USB expander shall be CE marked, UL listed, and compliant with the RoHS directive. Warranty shall be five years. The AVB/USB expander shall be Tesira EX-UBT. Makes- Biamp/Polycom/Symentrix

SITC of Audio Conference System Controller/Central Unit having following Technical specifications:

a) Digital Technology b) Control upto 40 with Central Unit and expandable upto 400 Units c) Frequency response to be 25Hz to 15 KHz (+/-3dB) d) Built In Conference Manager Software for Controlling Conference e) Should have 2 USB port for Connecting Keyboard/Mouse or can be used for recording f) Cable Management Via Daisy Chain,redendancy mechanisum g) Compatibility with PC and media control units via touch panel h) Direct Recording feature Via USB only (SD Card, external Recorder & other software Not Applicable)i) Max. Open Microphones to be min 6 & Max 8 j) Operating voltage to be 48V dc – 3.15A k) Total harmonic distortionto be ≤ 0.02% l) Conference Interface should be available on a PC with a connectivity through central unit

m) Power consumption to be 2W n) Electronically balanced XLR In o) Built in Open Media Control Protocol for Camera p) Ethernet (compatible to Crestron and other brands) q) Permanent malfunction monitoring and error diagnostics r) Input voltage range to be 100-240Vac , 47-63Hz s) Can be interfaced with a wide range of external equipment’s t) Digital acoustic feedback suppression u) Output level to be > -40dBV v) No Initialization procedure required for Adding New Unit w) Shielding Technology to immune for the interference from Mobile Phone x) No Propriety Cable to be used in connecting the Chairman & Delegate unit y) Headphone output with Headphone volume adjustment z) .OEM Must having Own TWO Service Center In India. Makes- Brahler/Sennehiser/Biamp/Bosch or any make approved by engineer incharge

SITC of Delegates Microphone having following technical specifications

a) Table top gooseneck Unit with microphone Quality super Cardioid for delegate with on-off button with loop in loop out of microphones,

b) Table Top Unit with Microphone Quality Cardioid.

c) In-Built Twin Loudspeakers

d) Cable Management Via Daisy Chain,redendancy mechanisum

e) Gooseneck with LED light Ring & Bi-color bar indicator

f) Length of gooseneck to be min 300mm

g) Sheilding Technology to immune for the interference from Mobile Phone

h) No Propriety Cable to be used in connecting the Chairman & Delegate unit

i) Headphone output with Headphone volume adjustment

j) Operating voltage to be 3.3V DC, 0.5 mA

k) Power consumption to be 0.5 mA (without LED ring); max. 25 mA (with illuminated ring)

l) Pick-up pattern to be Unidirectional, cardioid

m) Frequency response to be 130 Hz – 150000 Hz

n) Load impedance to be > 5kOhm

o) Free field sensitivity to be 7mV/Pa, +/- 3 dB at 1 kHz

p) Operating temperature to be 5°C to 50°C Makes- Brahler/Sennehiser/Biamp or any make approved by engineer incharge

SITC of Chairman Microphone having following specifications:

a) Table top gooseneck microphone Quality Cardioid for Chairman with on-off button, Priority/ mute button with loop in loop out of microphones,

b) Table Top Unit with Microphone Quality Cardioid

c) In-Built Twin Loudspeakers

d) Cable Management Via Daisy Chain,redendancy mechanisum

e) Gooseneck with LED light Ring & Bi-color bar indicator

f) Length of gooseneck to be min 300mm

g) Shielding Technology to immune for the interference from Mobile Phone

h) No Propriety Cable to be used in connecting the Chairman & Delegate unit

i) Headphone output with Headphone volume adjustment

j) Operating voltage to be 3.3V DC, 0.5 mA

k) Power consumption to be 0.5 mA (without LED ring); max. 25 mA (with illuminated ring)

l) Pick-up pattern to be Unidirectional, cardioid

m) Frequency response to be 130 Hz – 150000 Hz

n) Load impedance to be > 5kOhm

o) Free field sensitivity to be 7mV/Pa, +/- 3 dB at 1 kHz

p) Operating temperature to be 5°C to 50°C

q) The chairman version comes with a priority and next-in-line function.

Makes- Brahler/Sennehiser/Biamp or any make approved by engineer incharge

SITC Of 65 Inch Interective Screen Panel having following technical specifications

Display Type: LCD

Display Size (in.): 65 Inch

Viewable Area (in.):65 Inch

Light Source:LED

Resolution:3840 x 2160

Refresh Rate (Hz):60

Aspect Ratio: 16:9

Static Contrast Ratio:1,200:1

Dynamic Contrast Ratio:5,000:1

Backlight Life (Hours):50000

Brightness:350 cd/m2

Viewing Angles:178º horizontal, 178º vertical

Panel Surface:9H

Operation Rating:16/7

Ethernet LAN:10/100/1000 Mbps

Embedded Player:

OS:ViewBoard OS (embedded Android 8)

GPU: ARM Mali-G51

CPU:ARM Quad Core A73 + A53

CPU Processor Speed:A73: 1.1GHz, A53: 1.5GHz

Memory: 3GB

Storage:32GB

Audio:

Internal Speakers:10W (x2)

Subwoofer:15W (x1)

Connector:

HDMI 2.0 In(3), VGA(1), Composite RCA(1), 3.5mm Audio In(1), 3.5mm Audio Out(1), SPDIF Audio Out(1), USB 3.0(4), USB 2.0(3), Slot-in PC Slot(1), USB B Touch Port(2), RS232(1), Ethernet LAN (RJ45)(1), WIFI Module Slot(1)

Power:

Voltage:100-240 VAC

Consumption (max):350W

Consumption (typical):104W

Stand-by:<0.5W

Operating Conditions:

Temperature:32-104º F (0 - 40º C)

Humidity (non-condensing):10-90%

Touch:

Touch Technology:Infrared

Touch Points:20-Point Touch

Tip Detection:Dual tips, 3mm and 8mm

Weight (imperial):

Net (lbs):88.9

Gross (lbs):102.6 with Wall Mount Stand

Make: Sony/Viewsonic/Panasonic/Samsung or any make approved by engineer incharge

SITC of wireless presentation hub shall be designed to connect web-based soft codec conferencing systems with in-room audio and video devices. It shall also allow multiple session participants to directly receive content from in-room audio/ video devices on their compatible computing devices via the use of custom USB drivers. The wireless presentation hub shall connect to AV peripherals via a Universal Serial Bus (USB) connection using a standard USB 3.0 A-type connector. The wireless presentation hub shall be equipped with one High-Definition Multimedia Interface (HDMI) port on the rear panel. The wireless presentation hub shall connect to an Ethernet network via an RJ-45 connector to allow participants using client devices to join a shared session. The client devices shall operate using Windows, Mac OS X, iOS or Android operating systems and shall have installed the Modena Hub custom drivers and client software. The wireless presentation hub shall be CE marked, UL listed, and compliant with the RoHS directive. Makes- Extron/Biamp/Polycom or any make approved by engineer incharge

SITC of Hi Speed HDMI Cable Ultra high speed 8K HDMI cable with 48Gbps transmission speed Durable, high-quality build protects against corrosion while maximizing signal strength - 100% Pure copper conductors, Triple Cable Shielding, 24K Gold-plated full metal jacket connectors Make: Krammer/Bestnet/Creston or any make approved by engineer incharge

SITC of Mic Cable with Power/Voltage 350W, Material PVC, Voltage 220V Gauge 19/40+128/44 Shilded Cable Make: Creston/Bestnet/Krammer or any make approved by engineer incharge

SITC of 45/50L Refirigerator having technical specifications:

Total Capacity :45/50Ltrs.

Refrigerator Style:Single Door Refrigerator

Stabilizer Free Operation

Refrigerant:R600a

Dairy Compartment

Child Lock

Refrigerator Shelf Type Make: LG/Samsung/Haier or any make approved by engineer incharge

Supply Installation Testing and Comissioning of Digital Phone with following Specification: Handsfree and open listening, 15 Programable Keys, , WithDisplay, Last number redial (Approved Makes: SYNTEL , ALCATEL , NEC or any make approved by engineer incharge

Supply Installtion Testing and Comissioning of Analog Phone with following Specification: Handsfree and open listening, 50 entries for CLIP, Last number redial (Approved Make: Bina Tone , Syntel , Beetal, Panasonic or any make approved by engineer incharge

SITC of Mixing Aplifier having following specifications

Bidder Name

Amount

R. C. ENTERPRICES(GSTN-08ACXPC2792A1ZJ)

GANPATI COMMUNICATION SERVICES(GSTN-08AMAPG7177L1ZP)

R. C. ENTERPRICES

GANPATI COMMUNICATION SERVICES