WBPWD/EE/AED /eNIQ-86/2024-25

Amount

Supply of polygonal shape 16 mtrs. High mast pole with its accessories. Mast shaft shall be in two section, made from H.T. Steel of grade BSEN 10025,S355JO hot dip galvanised and suitable for wind speed 180km/hr as per IS 875. It shall also included all accessories for hight mast including head frame, two continues steel wire Rope mm (Grade AISI 316), trailing cable, double drum winch galvanised lantern carrage arrangement suitable for 8 nos. luminaries symmetrically and its cotrol gear box, Motor, Manual operating handle, Motor mounting plate, L-Staper, Lighting arraster, Junction box. Including Foundation acc.The mast shall have an intigral pwer tools installed inside the base compartment for its operation. Luminaries wiring materials included in the mast supply price.(BPP/Utkarsh/Bajaj)

Erection of 16 mtr. Hight High mast with all accessories With modern engineering practices including fixnig lighting fixture.

Supply and installation of outdoor Feeder Piller box of size 2.5'(H) x 2'(W)x 1.5'(D) as per direction of EIC.Canopy and upper portion of the Feeder Pillar box is to be made from 5mm & 3mm thick MS Sheet respectively, and bottom portion with 10mm thick MS plate rigidly fixed by nuts bolts washer etc. The Pillar Box will have double door with almirah type lock with 3 nos. keys. Additional provision of pad locking is to be provided with 2 nos. mechanical locks both top and bottom portion. Provision of ventilating grill should be triangular in shape made from MS Plate duly welded to lateral side. The centre ventilation spout at starting surface of the top of the pillar box.Provision of 2 Nos. earthing terminals by 25x6mm GI flat having suitable nuts, bolts & washers etc. The pillar box is to be painted with 2 coats of synthetic enamel paint after one coat of RO primer. The internal EI works of the pillar box should withstand 2KV rms AC Voltage for 1 minute. All fabrication work is to be done as per direction of EIC. The Pillar box should contain the fallowing components incl. painting the pillar box as per G.S. A) Timer DB(16 SWG) which comprises the followings :- i) 32A 4 pole FPMCB (Legrand)-1 ii) 240V, 25A TP cotractor(LT Make)-1 no. iii) Suitable Day dial Timer (GIC)/Digital time switch(LT make) -1 no. iv) By pass switch- 1 no. v) outlet Teminal -2 nos. B) Starter for moter operation (Forward and Revers direction)-1no. C) 32A FPMCB on DIN Rail ( Legrand Make)-1 no.

Supply and Fixing of 200Watt Lence type,120 Lumen/Watt LED Flood Light fixture(Make-CG/Havells/Phillips/Surya Livia/Magik/Orient Alpha) with 5 years warranty.

Supply and Fixing of 120 Watt Lence type,120 Lumen/Watt LED Flood Light fixture(Make-CG/Havells/Phillips/Surya Livia/Magik/Orient Alpha) with 5 years warranty.

Construction of suitable shallow foundation with 1:2:4 or M20 grade concreate for the hight mast considaring the safe soil bearing capacity at site as 10T/sq. mtrs. At 2X 2Mtrs. Depth with all materials and lobour charge as per approval drawing.

Making earthing of high mast with 50 mm GI pipe & wire (3 Mtr long) with G.I. strips as per direction of E.I.C.

S/F 32A TPN mainswitch on existing angle iron frame (Make-Havells/HPL/STANDARD)

S & laying of underground 1100 V, 4 core, 10 sq. mm. PVC/A AI. Cable with 1 x 10 SWG G.I. wire as eathin attachment suspended in air as per G.S. for service connection purpose.

S & fixing cable gland & socket of following sizes with finishing the end. a) 4 core x 10 sqmm

S&F medium gauge 25 mm dia GI Pipe ( ISI-Medium) for cable protection with necy. fittings and jointing metarials as required.

Supply and fixing of (3x10+1x6) sqmm PVC insulated and unsheathed single core stranded copper wire through 32mm dia polythene pipe.

Finishing of the above PVC insulated wire ends of by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. a) 6 sqmm

b) 10 sqmm

S&F of 240V, 32 A DP main switch with fuse on L&N on angle iron frame on wall/feeder piller box. (make- standard, havells, HPL)

Distn. Wiring with 1.1 KV grade single core stranded copper conductor PVC insulated and unsheathed copper wire (MESCAB/ KEI/ RR Kable/ Polycab) in 20 mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required ( for TPNDB to timer DB ,loop box to signage board etc.) 2 x 2.5 sqmm + 1 x 1.5 sqmm

Supply of 2/3.5 Core XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make Mescab / Gloster/KEI/Polycab] 2 Core 6 Sqmm.

Laying of cable upto 35 sqmm in underground trench as per GS for the following numbers of Cables.

Laying of cable upto 2 core 25 sqmm on wall/surface incl. S&F MS saddles with earthing attachment in 10 SWG GI(hot dip) wire etc.

Laying only Cable upto 50 sqmm through existing GI Pipe 2/ 4 core

Supplying & delivery 40mm dia medium gauge GI Pipe ( ISI-Medium) as required for cable protection

Supplying and fixing compression type gland and finishing those with suitable size socket by crimping method for following XLPE / PVC armoured cable (2/4/3.5)Core as per GS. 2 Core 6 Sqmm

S/F Stainless Steel water proof looping cable box of size 200x150x100mm having hinged top Cover with rubber gasket lining, railway type mechanical locking anangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one230 V, 6 A MCB unit, one NL on porcelain insulator etc. and housing the same on pole above 5ft from ground level by necessary pole clamp .

SITC of LED illumination sign board fabricated by ACP box supported with 1"x1" MS hollow square pipe of 18swg all around/rail pole. The 3mm ACP facial should be provided with Laser cutting 6mm thick acrylic letter out of which 3 mm rising from the surface of the ACP board. 6mm letters should be fixed on another 3 mm acrylic sheet on back side of the ACP facial. Border line of the front portion and back portion should be coverd by 1.5" aluminium channel as per the direction of EIC.all the matters / contains as approved by the authority. The Sign board should be glow from back side of letters by 1.5W/2.0 LED 2/3/4 module cool white in colour inculding 12 Volt 615W power supply and LED must be covered in box made of 3 mm thick sun board 4" with part of the four side of board should be covered by ACP after bending excess part from front side. The sign board should be fixed as per direction of EIC with suitable supporting arrangement on floor and mending good damages as per direction of EIC. Colour of APC & letter will be as per direction of EIC. The cost transpotation and scafolding charges are included.

Supply and delivery 9 mtr rail pole.(Approved make, as per choice of EIC)

Erection of H-pole (DP) structure with upto 9 mts. long rail pole (0.9 mt. to 1.5 mt. apart) in CC (6:3:1) foundation (as to similar dimention in item A-1 above) including 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mt. dia & 0.30 mt. above ground level neately cemented finish 3 mm thick and providing Galv. MS Channels, cross arms and cross bracings made out of Galv. angle, flats etc. anticlimbing devices, danger board & earth bolts etc. & carrying of the pole upto 1.6 Km. from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly.

The all complete sign board would be fixed L-type (75mmx75mmx5mm) channel on which the sign board will be placed.with existing rail pole or wall with 2 nos support each structure with supply and Fixing L-type (75mmx75mmx5mm) MS Channel as per direction of EIC

Supplying & fixing 4 bars 415 V, 63 A sheet metal (16 SWG) Iron Clad Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required – (As per Drawing no. 470 of PWD Specification Book – May 1991) Dimension of bars 85mm long, 4 x 20x5mm & Dimension of Sheet Metal Box 500x150mm

Painting of Tubular Pole/pipe of following lengths and 2 nos. of aluminium coats of paint over 1 coat of RO priming with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint Upto 9 mtr. long pole

Supplying & laying 80mm dia medium gauge GI Pipe ( ISI-Medium) as required.

Extra on items above, for providing CC (6:3:1) base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) incl. drilled hole in pole suitable for alkathene/polythene pipe entry, for street light wiring, without Loop Box

S&D of 250V timer DB (equivalent to 8way SPNDB in size) with sheet steel enclosure double door, neutral bar, din rail, with IP43 protection comprises with 20/25A DPMCB(C curve 10ka) and 1 no 24 hr analog time switch and 1 no 18/25A power contactor complete with internal wiring with suitable size of copper wire including 1 no toggle switch (for AUTO/Manual) and LED indicator and earthing attachment as per direction of EIC(make- L&T/ Siemens/ABB)

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required .

Connecting the equipments to earth busbar including S & F 4 SWG GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.

Supply & fixing of Ring type Arm bracket on the top of the Octagonal Pole and arangement for fixing the four / six nos Out Door type Fittings. on the Arm bracket. The Ring type Arm bracket made with 32 mm dia GI pipe & diameter of the bracket appx 700 mm The bracket shall be fabricated & bending in round shape with heating at fabrication workshop & rolling machine shop with expert man power & welder incl S&F of necessary support inside the ring with 32 mm dia GI Pipe and also rose type arrangement at center of the bracket made by 100 mm dia GI pipe of required / length appx 15" long and shall be properly welded with smooth surface finish incl.S&F bolts, nuts and washer, GI socket etc for properly fixing arrangement at the top of the pole incl. painting to complete the installation as per standard design and direction of EIC.

Distn. Wiring with 1.1 KV grade single core stranded copper conductor PVC insulated and unsheathed copper wire (MESCAB/ KEI/ RR Kable/ Polycab) in suitable size PVC casing-capping (Precision make) incl. necy. fittings as required. 3x 1.5 sqmm cu wire

Add GST @18% On total from item no 1 to 35.

Add LWC @1% On total from item no 1 to 36.

R.K.ENTERPRISE (BID ID -5889876)

DURGAPUR POWER (BID ID -5875170)