ADDN/ALTERATION BLDG NO. P-7 TO 10, 8,9,10,64,65 AND 138 (54 JCOS MD ACCN) P-12,15,56,58,67 TO 69,71,72,114,110 AND 157(158 OR MD ACCN) AT VRC OF IHQ OF MOD (ARMY)CAMP AND INF BN DELHI CANTT

Amount

NORMAL REPAIR ITEMS OF BUILDING

Item No.1 Demolition (unreinforced) cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and directed.

Item No.2 Demolition of PCC (unreinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) complete all as specified and directed.

Item No.3 All as per item No. 2 above but exc 15 cm thickness but above ground floors.

Item No.4 M&L for applying a coat of cement slurry @ 0.488 Kg/Sqm mixed with tapercreate @ 0.253 Kg/Sqm after cleaning and drying the old/new surfaces then applying the layer of fibre glass cloth while the above coat is still green. The overlap of fibre glass cloth shall be not less than 100 mm and then applying 1.5 mm thick layer @ 1.288 Kg/Sqm mixed with taper create @ 0.570 Kg/Sqm and coarse sand @ 1.289 Kg/Sqm. Allow the treatment to air curing for four hours followed by water curing for 48 hours complete all as specified and directed.

Item No.5 M&L for 10 mm thick cement plaster on brick/ concrete surface in CM 1:3, finished even and smooth surface (with out using extra cement) but mixing water proofing compound at the rate of 2% of cement by weight etc complete all as specified and directed (WPC shall be paid separately).

Item No.6 Supply only liquid water proofing compound complete all as specified and directed.

Item No.7 M&L Cement concrete Type E2 (1:5:10) (using 40 mm graded stone aggregate) filling under sunken floor complete all as specified and directed.

Item No.8 M&L 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of flooring etc complete all as specified and directed.

Item No.9 M&L coloured glazed ceramic tiles joint free 450X300X7mm thick on vertical surface as in dados set and jointed in neat cement slurry and pointed in coloured cement to match over and including rendering 10mm thick backing coat with CM 1:4 etc complete all as specified and directed.

Item No.10 M&L for 25mm thick cement concrete type B-0 1:2:4 (12.5mm graded stone aggregate) as in sub base of floors finished rough etc complete all as specified and directed.

Item No.11 M&L for 15-17 mm thick marble (Green) udaipur green machine cut bedded jointed & pointed with grey cement slurry including cutting & polishing over and including 15mm thick screed bed in CM 1:4 including round the edges and making the suitable hole for gas pipe etc complete all as specified and directed.

Item No.12 M&L non skid coloured ceramic tiles jointless 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in cement plaster 1:6 for laying floor finishes etc complete all as specified and directed..

Item No.13 M&L 40mm thick PCC flooring type B-1, 1:2:4 (using 20mm graded stone aggregate) finished cement concrete surface even & smooth without using extra cement etc complete all as specified and directed..

Item No.14 S&F 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) tripple layer white colour hoisted and fixed in position complete all as specified and directed.

Item No.15 M&L 75mm thick PCC type C-2, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection finishing cement concrete surface even & smooth without using extra cement complete all as specified and directed.

Item No.16 S&F in repair squatting pan size 580x440mm (Orissa pattern) including connection to trap and to flushing pipe, anti syphonage pipe, etc complete including making good to floor etc complete all as specified and directed.

Item No.17 M&L for vitreous china wash hand basin flat back size 550x400mm white excluding taps waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mmx600mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed. Note: WHB will be supported on angle iron of size 50x50x5mm duly paintd with two coats of synthetic enamel paint for securing WHB.

Item No.18 Dismantling Cast iron pipe 100 bore incl all fittings of any description and in any position etc complete all as specified and directed..

Item No.19 All as per item No. 18 above but 75mm bore

Item No. 20 S&F 100 mm bore sand cast iron soil waste and vent pipe in any length with or without ears with cement joint fixed to walls including MS steel flat iron 25X3 clamp etc complete all as specified and directed.

Item No. 21 All as per item No. 20 above but 75mm bore

Item No. 22 Refixing of 100mm bore sand cast iron soil, waste & vent pipe in any position etc complete all as specified and directed.

Item No. 23 All as per item No. 22 above but 75 mm bore

Item No.24 S&F 100mm bore (CI) Bends diminishing pieces or tapers (larger bore mesured) complete all as specified and directed.

Item No. 25 All as per item No. 24 above but 75mm bore

Item No.26 S & F 75mm dia oval assess door cover for 75mm bore CI pipe including rubber packing & bolts etc complete all as specified and directed.

Item No.27 S&F Branch pieces,Tee junction with bore of pipe 100 mm, single (equal or unequal), ordinary or inverted, (spigot or socket type) or with parallel branches with Oval Access door etc complete all as specified and directed.

Item No. 28 All as per item No. 27 above but 75mm bore

Item No.29 M&L 75 mm (outlet dia) CI floor trap, with grating incl jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified and directed.

Item No.30 S&F in repair PVC (SWR) 150X150 mm dia gully traps, square or round mouthed type 'P' etc complete all as specified and directed. .

Item No.31 Taking down cement or cement lime plaster on brick/concrete surface including terrazo dado etc. including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed..

Item No. 32 Removing old lime wash etc,hacking for key raking out joints of old brick work or stone work built in cement mortar, not previously plastered; and scrubing down with water etc. to receive plaster complete all as specified and directed.

Item No. 33 M&L for 15 mm thick rendering in cement mortar 1:4 on brick or concrete surfaces finished even and smooth surface wihtout using extra cement on external wall upto four stories bldgs complete all as specified and directed.

Item No.34 All as per item No. 33 above but other than fair faces in CM 1:6.

Item No.35 M&L for 10mm thick rendering in cement mortar 1:4 on concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed.

Item No.36 Taking down chowkhats or frames exc 1.5 sqm but n. exc 4.00 sqm each but (without taking off shutters from the frame) etc complete all as specified and directed.

Item No.37 All as per item No. 36 above but n. exc 1.5 sqm each

Item No.38 Taking down shutter of any description exc 1.00 sqm n. exc 2.00 sqm each and refixing in the same opening including easing and adjusting complete all as specified and directed.

Item No.39 S&F 35mm thick plain framed 2nd class hardwood panelled shutter , factory made (two panel ) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle boards with commercial veneering on both face, the size of rail and stile as per IS 1003 (Part-1), kiln seasoned and chemically pressed, treated complete incl 15 to 20 mm tapering beading on one face of second class hardwood fitted to chowkhats complete all as specified and directed

Item No.40 M&L 35mm thick 2nd class hardwood factory made glazed and skeleton shutters, open rebated and prepared to receive gauge, glass etc divided into square with plain, chamfered or rounded fitted with cut and mitred beads for receiving gauge etc complete all as specified and directed.

Item No.41 S&F factory made solid panel FRP door shutter 30mm thick premoulded design made out of solid core, laminated 1.5 mm to 2mm thick GRP/FRP made of superior all season weather resistant polyyester gel coat followed by laminating polyster resin of 450 gm glass mat termite all as per manufacturers specification etc complete all as specified and directed.

Item No.42 S&F factory made solid FRP door frame of size 90mm x 45 mm made out of FRP sheet , suplying and fixing as per direction Engr-in-Charge or complete all as specified and directed.

Item No.43 M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaces finished even and fair complete all as specified and directed.

Item No.44 S&F 100mm size butt hinges stainless steel of AISI 304 complete all as specified and directed.

Item No.45 S&F stainless steel of AISI 304 grade barrel tower bolt 200 mm long, extruded section, etc complete all as specified and directed.

Item No.46 S&F stainless steel of AISI 304 grade handle of size 200mm size long etc. complete all as specified and directed.

Item No.47 S&F 300 mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clipss of sheet, cast or extruded sections and fixing bolts and fixed etc complete all as specified and directed.

Item No.48 S&F 100 mm long, stainless steel of AISI 304 grade, hasp and staple, safty type, incl bolt to hinge plate and fixed with screws etc. complete all as specified and directed.

Item No.49 S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

Item No.50 All as per item No. 49 above but as in repair after taking down old wire cloth.

Item No. 51 S&F as in repair for welding of 100mm size butt hinges stainless steel of AISI 304 including taking down shutter exc 1.5 sqm but n. exc 2.0 sqm and refixing in same position and making good/functional incl supply of new butt hinges etc complete all as specified and directed.

Item No. 52 Hacking out old broken glass of (any size, thickness, quality or description) from metal frame, including punching or drilling out old glazing pins/springs clips and provided fixing new one exc 1.5 sqm each pane etc complete all as specified and directed.

Item No. 53 S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exec 0.5 sqm each pane complete all as specified and directed.

Item No. 54 All as per item No. 53 above but figured glass pin headed type.

Item No. 55 S&F coloured fibre reinforced plastic /perpex, translucent sheet 4mm thick glazing with oil putty in squares not exec 0.5 sqm each pane complete all as specified and directed.

Item No. 56 M&L preparation of newly plastered surfaces of wall and applying 3 coats of white wash etc complete all as per specified and directed.

Item No. 57 All as per item No. 56 above but applying 2 coats of OBD over a coat of alkali resistant priming paint white or tinted complete all as specified and directed.

Item No. 58 All as per item No. 56 above but 3 coats of white wash in ceiling

Item No. 59 M&L preparation of old decorated plastered or plastered wall surfaces including plaster of ceiling and cornices etc including brooming down or steel wire brushing and applying two coats of white wash complete all as specified and directed.

Item No. 60 M&L for grinding existing internal surfaces complete and removal through electrically operated grinder including preparation of surfaces complete all as specified and directed.

Item No. 61 M&L for priming on wall plastered and other surfaces with alkali resistant priming paint etc complete all as specified and directed.

Item No. 62 M&L for distemper on walls with two coats of oil emulsion distemper white or tinted complete all as specified and directed.

Item No.63 M&L for preparation of old decorated surfaces on ceiling & applying two coats of white wash complete all as specified and directed.

Item No. 64 M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed..

Item No.65 M&L for preparing old decorated wooden surfaces of any description not otherwise described over 10 cm width or girth & applying one coat of synthetic enamel paint of any colour complete all as specified and directed.

Item No.66 M&L for preparing old decorated steel surfaces of any description not otherwise described over 10 cm width or girth & applying one coat of synthetic enamel paint of any colour complete all as specified and directed.

Item No.67 M&L Cutting chases for concealed water tubing or concealed conduct wiring etc.and making good cutting n exc 10cm girth in brick wall complete all as specified and as directed.

Item No. 68 S&F in repair 15mm bore galvanised iron pipe mediun grade with all fitting fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections etc complete all as specified and directed.

Item No. 69 All as per item No. 68 above but 20mm dia bore.

Item No. 70 All as per item No.68 above but 32mm dia bore.

Item No. 71 All as per item No. 68 above but 50 mm bore

Item No. 71A All as per item No. 68 above but 25 mm bore

Item No. 72 Refixing of old steel tubing and connection in new or old position (Wall/Ceiling / floorsetc) including cleaning for refixing, bore of pipe 15 mm bore GI pipes and connections etc complete all as specified and directed .

Item No. 73 All as per item No. 72 above but 20mm dia.

Item No. 74 All as per item No. 72 above but 50mm dia.

Item No. 75 S&F in repair stainless steel plate rack of AISI 316 grade made of 1mm thick stainless steel sheet of size 775mmx900mmx200mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big untensils and seven nos of small utensils divided by 10mm dia stainless steel hollow pipe @ 60mm centre to centre or as per drg and sample kept in GE's office complete all as specified and directed.

Item No. 76 S&F in repair sinks made of stainless steel AISI 316 grade 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waist pipe including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle and connecting union to pipe overall size 510x430 bowl size 430x 380mmx160mm, etc. complete all as specified and directed.

Item No. 77 S&F in repairs 10 ltrs capacity PVC Low level flushing cistern including PVC syphon and float valve with float, PVC long bend for out let connection of cistern with WC complete fixing and connecting bend with WC complete all as specified and directed.

Item No. 78 S&F in repair of chromium plated fancy type pillar tap 15mm bore, cast copper alloy, with capastan heads, chromium plated, screwed down high pressure, with or without letter 'HOT or Cold' with long screwed shanks & fly nuts, screwed for iron pipe & fixed etc complete all as specified and directed.

Item No. 80 M&L cutting of trees including cutting of trunk n.exc 30cm girth and branches and digging out roots from floor or roofs and walls of up to four storied bldg and making good the dismantled portion in cement mortar 1:3 to match the existing surfaces complete all as specified and directed.

Item No. 81 Dismantling Brick tiles or terracing tiles single layer on roofs etc complete all as specified and directed.

Item No. 82 Demolition mud in roofs any thickness including plastering and leaping complete (whether full) thickness removed or only a part thereof and removal from site etc complete all as specified and directed.

Item No. 83 M & L applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 Kg per sqm including cleaning surfaces complete all as specified and directed.

Item No. 84 S&F APP polymeric water proofing membrane minimum 3mm thick and weighing not less than 3.5 Kg per Sqm of make "multiplas" manufactured by STP Texsa Ltd or Hyper plas polymer water proofing membrance manufactured by M/s IWL India Ltd or 'Shali plas' (polyester) manufactured by M/S Capital Steels and Chemicals Pvt Ltd or "Make Poly Plast" manufactured by M/S M K Petro, STP superior polyplas manufactured by STP Ltd as approved by GE, black finish reinforced with non woven polyester matt with a thermo fusable finish laid over a coat of bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butane gas torch with an overlap of 100mm at the sides and 150mm at the ends and incl applying a coat of cold emulsion bituminous primer all as per manufacturers instructiions incl preparation of surface complete all as specified and directed. Note The water proofing treatment shall be got carried out by manufacturer or their authorised applicators complete all as specified and directed.

Item No. 85 M&L 40 mm thick brick tile laid on 15mm thick screed in cement mortar 1:6 and jointed & pointed in CM 1:3 with 5% of linseed oil by weight of cement in cement mortar etc complete all as specified and directed.

Item No. 86 All as per item No. 85 above but except brick tiles.

Item No. 87 Demolition of brick work built in CM incl quoins, arches, pillers etc complete all as specified and directed.

Item No. 88 M&L brick work in cement mortar (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified and driected.

Item No. 89 M&L brick work in cement mortar (1:4) using sub class 'B' bricks, straight or curved in plain exc 6 mtr mean radius in half brick thick wall etc complete all as specified and directed.

Item No. 90 Demolition of RCC of any description, in any position roofs, floors (other than ground floors), beams staircases, landing, chajjas, RCC overhead tank and similar suspended work complete all as specified and directed.

Item No. 91 M&L for form work to chajjas and similar items including edges complete all as specified and directed.

Item No. 92 M&L for RCC 1 : 2 : 4 type B-1 (using 20mm graded stone aggregate) as in chajjas etc complete all as specified and directed.

Item No. 93 S&F 10mm dia TMT bar as in reinforcement , cut to length bent to shape required including cranking, bending, binding spirally for hooping for coloumns, hooking ends with MS wire annealed not less than 0.90mm dia complete all as specified and directed.

Item No. 94 All as per item No. 93 but 8mm dia TMT bar.

Item No. 95 M&L in repair 110mm bore PVC (SWR) pipes conforming to relevant IS single socketed in any length with rubber ring joint and fixed to wall with MS flat iron clamp 25X3 mm complete incl taking down old rain water pipes etc complete all as specified and directed.

Item No.96 S&F in repair 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

Item No. 97 M&L for RCC 1 : 2 : 4 type B1 (using 20mm graded stone agg) as in roof slab suported on wall beams and columns in floor slab complete all as specified and directed.

Item No. 98 M&L for form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exc 200mm thick finished rough (horizontal and sloping) etc complete all as specified and directed.

Item No. 99 All as per item No. 98 but edges of concrete flats, sides of RCC/PCC band in wall, horizontal or sloping.

Item No. 100 M&L for cutting holes into or through one brick thick brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required superficial area exc 400 sqcm but nexc 0.10 sqm round shape for exhaust fan etc.

Item No. 101 M & L for 20-22 mm thick Machine cut kota single piece stone slab for steps and size 22''x22'' for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 and rounding of edges, rubbing and polishing complete all as specified and directed.

Item No. 102 All as per item No. 101 above but in riser of steps, skirting dado and pillar laidown cement screed complete all as specified and directed.

Item No. 103 M&L for precast cement concrete 1:2:4 type B-1 (using 20 mm graded aggregate) as in manhole cover slabs round, square or rectangular in shape set in cement mortar 1:4 etc complete all as specified and directed.

Item No. 104 M&L for cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, coping, benching, roof kerb or mud stops, seismic and other similar bands, parapets and railings upto 60 cm in height, copings, apex stones, including form work to concrete surfaces etc complete all as specified and directed.

Item No. 105 S&F in repairs cast iron (sand cast) soil, waste and vent pipes in any length, with or without ears, with cement joints, laid in trenches or in floors or fixed to walls, bore of pipe 50 mm bore etc complete all as specified and directed.

Item No. 106 S&F in repairs cast iron cowl for 50 mm bore of pipe complete all as specified and directed.

Item No. 107 S&F Stainless steel soap dish of AISI 304 any type fixed to plugs with chromium plated brass screw complete all as specified and directed.

Item No. 108 S&F stainless steel Peg set of 3 pegs of AISI 304 as per sample complete all as per specified and directed.

Item No. 109 S&F in repair brass chromium plated 125 mm dia shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40 gms) etc complete all as specified and directed.

Item No. 110 S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) etc complete all as specified and directed.

Item No. 111 S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms) etc complete all as specified and directed.

Item No. 112 S&F in repair of Towel ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats etc complete all as specified and directed. (minimum weight 90 gms)

Item No. 113 S&F in repair of Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) etc. complete all as specified and directed.

Item No. 114 S&F 20mm Ball valves high pressure of PTMT (minimum weight 210 gms) with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed (minimum weight 15mm-142 gms/20mm-210gms/25mm-455gms/40mm-690gms) etc complete all as specified and directed.

Item No. 115 S&F 15mm dia fancy type chromium plated bib taps, cast copper alloy with crutch or capastan head, high preessure, screwed down high pressure screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed.

Item No.116 All as per item No. 115 but in repair.

Item No. 117 S&F Angle stop 15mm dia valve of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15mm-90gms) etc complete all as specified and directed.

Item No. 118 All as per item No. 117 above but in repair.

Item No. 119 S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed etc complete all as specified and directed.

Item No. 120 S&F drappery curtain rods stainless steel 30mm dia of approved quality with decorative wooden finish and two number brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod including 8 Nos (min) match up rings etc complete all as specified and directed.

Item No. 121 S&F 15mm nominal internal bore PVC connection 450 mm long with two brass nuts and PVC washer etc complete all as specified and directed.

Item No. 122 S&F Grating doom 100 mm dia of PTMT (minimum weight 25 gms) complete all as specified and directed.

Item No. 123 S&F Grating doom 125 mm dia of PTMT with waste hole (minimum weight 40 gms) complete all as specified and directed.

Item No. 124 M & L Chequered cement concrete tiles 25cm x 25cm x22 - 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement without pigment laid on screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) for laying floor finishes etc complete all as specified and directed.

Item No. 125 M & L for rectified, Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cm 1:6 for laying floor finish & roughening of floor by chiseling etc complete all as specified and directed.

Item No. 126 M&L for rectified non skid ceramic coloured tile 7 to 8 mm thick (rectangular) of size 600 x 100mm as in skirting set and jointed in neat cement and pointed in white or coloured cement to match etc, complete all as specified and directed.

Item No. 127 M & L 16 to 18 mm thick polished granite stone for corner shelf 12"x12" including making half round to exposed edges, chase cutting & fixed in brick wall complete all as specified and directed.

Item No. 128 S&F brass magic eye for panelled/flush shutter 35mm thick complete all as specified and directed.

Item No. 129 S & F 40mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings for over flow pipe of PVC water tank including connection to tank fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

Item No. 130 S & F 40 mm PP-R connection nipple for water tank to overflow PP-R pipe 40mm dia etc complete all as specified and directed. .

Item No. 131 S&F PVC laminated GI wire 2.00mm dia for cloth drying with S&F fastener as per site requirement complete all as specified and directed.

Item No. 132 S&F in repair of 15mm Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed, but fancy type, chromium plated all as specified and directed.

Item No. 133 S&F MS round bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for guard bars etc complete all as specified and directed.

Item No. 134 M&L fixed in repair 25 mm thick block boards, grade 2 quality , interior grade, commercial type, fixed with screws to timber frame work etc complete all as specified and directed.

Item No. 135 S&F continusous Piano hinges width of flaps (when open) 30 mm stainless steel, bright finish or electrogalvanised etc complete all as specified and directed.

Item No. 136 S & F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section as under, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. (a) Style rail – Jindal Section No.20805 or 20807, 40mm x18mm x0.91mm thick, Wt. @ 0.325 Kg/RM or equivalent. Note: Glass and other fittings material shall be measured & paid separately.

Item No. 137 M & L 6mm dia powder coated aluminium decco grill, (minimum thickness of powder coating 50 micron), section No-104, 100mm aperture of hexagonal design and pattern as approved complete all as specified and directed.

Item No. 138 M&L preparation of newly plastered surfaces on external wall complete incl applying two coat of cement base paint over priming plastered and other surfaces with alkali resistant priming paint complete all as specified and directed.

Item No. 139 S & F powder coated aluminium decco grill (minimum thickness of powder coating 50 micron) aluminium frame of desired section as per site requirement for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Item No. 140 S&F powder coated aluminium window glazed/gauzed window shutters, sliding type Three track (each shutter approx. half the size of opening with two Nos. glazed & one No wire gauzed shutter) (with stainless steel wire gauze) including necessary jointing cleats for fixing etc, glazing clips, rubber packing, snap beading, screws, aluminium (anodised) fittings such as handle (suitable size), locking device, and glazing & gauzing in panels with 4 mm thick coloured/tinted glass with rubber beading, glazing clips and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm using Jindal Aluminium Section Id 491, 4309, 4310, 8853, 8851, 9205 complete all as specified and as directed by Engineer-in-Charge. (In case of non-availability of any particular section, the highter section in terms of Kg/rm shall be provided without any extra cost to govt.( The thickness of shutter shall be 1.6mm and the thickness of glass shall be 4.00mm.) etc complete all as specified and directed.

Item No. 141 M&L for grinding existing external surface and complete removal of existing treatment on wall external (removal through electrically operated grinder) & preparation of surfaces with two coat of cement base paint etc complete all as specified and directed.

Item No. 142 S&F framed work as in doors or gates of angle or other section with gusset plates, rails braces, etc complete drilled for fixing or steel sheeting or other covering doors etc to the prepared for hanging or sliging with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other ncovering running rails and guides and hanging also fastering and fixing complete FE 290 (Gde E-165) etc complete all as specified and directed.

Item No. 143 S&F stainless steel of AISI 304 grade floor door stopper with hard drawn steel spring 140 mm long etc complete all as specified and directed

Item No. 144 S&F stainless steel of AISI 304 grade barrel tower bolt 100 mm long, extruded section, etc complete all as specified and directed

Item No. 145 S&F stainless steel handle of of AISI 304 size 100 mm size long , etc complete all as specified and directed

Item No. 146 Taking down carefully the old U/S Aluminium/ Copper point wiring (light, fan, socket or power) complete fitting such as switches ,ceiling roses ,pendants, sockets ,regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish etc complete all as specified and directed (credit for above items should be made as per condition separately).

Item No. 147 M&L for point wiring complete with , standard copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in and including concealed PVC conduit medium grade and sunk in new pressed steel terminal boxes of required size factory made and factory painted with stove enameled black paint with top cover 3 mm thick plastic/laminated sheet of required colour with brass screw and cup washer with all accessories including 1.5 Sqmm standard copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified for following : Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash etc complete all as specified and directed.

(a) One light /fan/Bell point controlled by one way switch

(b) One light point controlled by two 2-way switch

(c) One 3 pin socket outlet 5 amps point independent board

(d) One 3 pin socket outlet 5 amps point on same board

(e) One 3 pin socket outlet , 15 amps on independent board with cable 2.5 Sqmm for main current and 2.5 sqmm as earth wire as power point.

Item No. 148 S&F switch piano, flush type 5/6 Amps single pole one way,ISI marked etc complete all as specified and directed.

Item No. 149 S&F switch piano flush type 6 Amp single pole two way ISI marked etc complete all as specified and directed.

Item No. 150 S&F socket outlet, 2/3 pin , 5 Amps, flush type, ISI marked etc complete all as specified and directed.

Item No. 151 S&F switch piano, flush type 15 Amps single pole one way,ISI marked etc complete all as specified and directed.

Item No. 152 S&F socket outlet 3/5 pin, 15 Amps, flush type ,ISI marked etc complete all as specified and directed.

Item No. 153 S&F bell push, flush type 5 Amps ISI marked etc complete all as specified and directed.

Item No. 154 S&F ceiling rose 3 terminal /PVC/Poly carbonate isolated body,ISI marked etc complete all as specified and directed.

Item No. 155 S&F socket type ceiling fan regulator electronic type 100 watt complete all as specified and directed.

Item No. 156 S&F in replacement for Batten holder with PVC body and back plate suitable for LED Bulb B-22 capacity etc complete all as specified and directed.

Item No. 157 S & F bell ding dong AC 230 volts, single pole complete all as specified and directed.

Item No. 158 S&F LED integrated batten light fitting T-8 18/20watt, 230 volts, 50 Hz, 4 feet, white, indoor decorative type, PVC extruded type complete with self ballasted LED tube rod including flexible copper cable of suitable size, circular hylum sheet upto 15 cm dia, 3mm thick for using junction box cover and flexible PVC pipe to cover naked cable including taking down old light fitting complete all as specified.

Item No. 159 S&F LED integrated batten light fitting T-8 9/10 watt, 230 volts, 50 Hz, 2 feet, white, indoor decorative type, PVC extruded type complete with self ballasted LED tube rod including flexible copper cable of suitable size, circular hylum sheet upto 15 cm dia, 3 mm thick for using junction box cover and flexible PVC pipe to cover naked cable including taking down old light fitting complete all as specified.

Item No. 160 S&F wall mounting light fitting City-4 type, 230 volts, 50 Hz, decorative wall light fixture made up of poly carbonate suitable for 15 watt retrofit CFL (B-22 Base) complete including flexible copper cable of suitable size, circular hylum sheet upto 15 cm dia, 3 mm thick for using junction box cover and flexible PVC pipe to cover naked cable including taking down old light fitting complete all as specified.

Item No. 161 S&F LED 6 watt, 230 volts, 50 Hz white bulk head light fitting in engineering plastic housing with clear prismatic complete with LED Lamp including flexible copper cable of suitable size, circular hylum sheet upto 15 cm dia, 3mm thick for using junction box cover and flexible PVC pipe to cover naked cable including taking down old light fitting complete all as specified.

Item No. 162 S&F self ballasted LED lamp, RETROFIT type, 9 watt, 230 volts, 50 Hz, B-22 base type suitable for wall mounting light fitting/batten holder complete all as specified.

Item No. 163 S&F in replacement LED building security light fitting 30 watt, 230 volts, 50 Hz, aluminium housing & clear glass type with LED lens for wide beam distribution, IP66 type with suitable SPD including flexible copper cable of suitable size, flexible PVC pipe to cover naked cable, fixing on & including 32/40 mm dia GI bracket made out of duly painted GI Pipe (Minimum 1.20 meter long), bend to shape as required at site with fixing clamps, nuts, bolts & washers including taking down old light fitting complete all as specified.

Item No. 164 S&F in replacement of MCB DB SPN 8 Way, 230 volts, 50 Hz, double door type, IP-43 Protection, flush mounting having suitable bus bar, neutral link, earth link suitable for MCB SPN/DP as incomer and MCB SP as outgoing complete all as specified.

Item No. 165 S&F in replacement MCB SPN 40 Amps, 230 Volts, 50 Hz, C curve, 10 KA breaking capacity including lugs & thimbles complete all as specified.

Item No. 166 S&F in replacement of MCB SP 6 to 32 Amps, 230 volts, 50 Hz, C curve, 10 KA breaking capacity including lugs & thimbles complete all as specified

Item No. 167 M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2x6 Sqmm , 1100 Volts grade on & including PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 6 sqmm for continuous earth wire complete all as specified and directed (Two runs of cable with 01 earth wire (1x6sqmm earth wire) shall be measured as one length) Note:- the rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required etc complete all as specified and directed. (Note : The rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete.

Item No. 168 S&F in replacement of loadline distribution board triple pole and neutral, 6 way, 415 volts, 50 Hz, double door type, IP 43 Protection, flush mounting having suitable bus bar, neutral link, earth link, vertical type suitable for MCCB 125 Amps as incomer and MCB SP/TP as outgoing complete all as specified.

Item No. 169 S&F in replacement of MCCB 125 Amps, 415 volts, 50 Hz, 4 pole, 36 KA breaking capacity, thermal magnetic release type including lugs & thimbles complete all as specified.

Item No. 170 S&F in replacement of ceiling fan 1200mm sweep with 5 star rated copper wound in white colour complete with all acessories conneting up with twin core twisted felxible copper wire all as specified and directed.

Item No. 171 Taking down any type of make of electric KWH meter and refixing in same position after replacement of submain wiring including replacement of lugs/thimbles suitable for meter of capacity upto 60 Amps single phase 50Hz meters including sealing meterial as per site requirement etc. complete all as specified and directed. (Note :- contractor will ensure that meter is working accurately of satisfaction of Engr-in-Charge.)

Item No. 172 M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 3.0 mtr below GL with top edge of the plate not less than 2.5 mtrs below normal GL and connected to earth plate. Earth plate surrounded by 15cm thick packed layers of charcoal dust and common salt upto 1.5 meter depth all around the earth plate and connected to earth lead of GI earth wire 4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel and thimbles and other end of the earth wire connected to DB and protected by galvanized iron or steel pipe light grade 15mm bore and water pipe 20mm bore GI medium grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES SSR Part-I of 2009 and also including making test point for testing of earthing made out of gun metal or phosphorous bronze size 75x75x25 mm etc comple all as specified and directed. Note:- 1.RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM weighing not less than 4 KG/sqmm in lieu of CI cover. 2. Charcoal dust and common salt upto 1.5 meter depth shall be filled in layers of 15 centimeters all around the earth plate. On testing after completion of earthing if desired earth resistance is not achieved, the earthing will be redone at no extra cost to obtain the desired earth values.

Item No. 173 S&F of water heater storage type 5 star rated (Geyser) of capacity 25 Ltr, vertical type, AC electric 230 volt complete with heating element, thermostat, 3 core lead, plug top, saftey valve, including electric and water connection and making good to disturbed surface complete all as specified and directed.

Item No. 174 S&F PVC connection with brass nipple 15 mm x 600 mm long with ISI marked suitable for geyser of 25 Ltrs capacity as hot and cold water connection complete all as specified and directed.

Item No. 175 S&F stopcock of 15mm dia cast copper alloy CP fancy type screwed to iron pipe and fixed complete all as specified and directed.

Item No. 176 S&F 15 mm bore pipe medium grade galvanised iron pipe with all fitting fixed to wall and ceiling or laid in floor complete all as specified and directed by Engineer-in-Charge.

STRUCTURAL REPAIR ITEMS OF BUILDINGS

Item No. 177 M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as directed by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed.

Item No. 178 M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

Item No. 179 M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

Item No.180 M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Item No. 181 M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencing from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. It is to be ensured that there is no obstruction in free flow of grouting materials complete all as specified and directed.

(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Item No. 182 M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : Pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardener shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly.

(vii) Allow entire effected surface to cure for 24 hours. (viii) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (ix) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Item No. 183 Supply & fixing 12mm dia steel sheer connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring mortar (The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item) complete all as specified and directed.

Item No. 184 M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

Item No. 185 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

Item No. 186 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete complete all as sspeified and directed. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

Item No. 187 M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

Item No. 188 S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 189 M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded meshis to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

India Guniting Corporation

AMIT ASSOCIATES

Siya constructions

M/s VINOD KUMAR SHARMA

DABAS CONSTRUCTION COMPANY

Shivom Projects Private limited