REPAIR /MAINT TO CERTAIN ROADS AND ROAD FURNITURE IN POCKET A AT JASAI MIL STATION UNDER GE (A) BARMER

M&L for preparing bituminous surface of existing road and marking 2.00 mm thick centre lines, stop lines, dashes, arrows etc and the like n exc 10 cm wide on roads pavements with hot applied thermo plastic road marking paint with glass beeds of approved colour conforming to BS 3262 -1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

M&L in repair for identification sign/cautionary mandatory and information sign board area exc 0.60 Sqm and n exc 1.20 Sqm with thickness not less than 3.0mm aluminium composite panel covered by encapsulated lens type retro reflective sheet (grade 3M type II diamond grade of make 3M/dark eye/SNI ) on both side with green base, including writing of necessary letter/symbols of reflective type fixed on and including stainless steel frame of size 25mmx25mm and hang on 50mm dia stainless steel pipe(fabrication work from SS-304 material) of height 2.4 mtr from ground level to top and post embeded in ground with PCC 1:3:6 TYPE C-2 using 40mm graded aggregate of size 45x45x45cm including necessary excavation and earth work and making plateform of size 150x45x30cm with PCC 1:2:4 using 20mm graded aggregate including necessary formwork and covering all exposed surfacess with black colour glazed ceramic tile (joint less) of size (600x300x7mm) / (450x300x7mm thick over and including 10mm thick backing coat in cement mortar(1:4) set and jointed in neat cement slurry and pointed to match the tiles complete. Note:- The specifaction of board is held with GE(A) Barmer as sketch. The letters and symbols etc on both side shall be as per site requirement of user and as approved by GE. The size and font of wording/ arrow/ symbols as per direction of Engineer In-Charge.

M&L for one coat of synthatic enamel paint on old concrete surface including surface preparation of any description (Road side cement concrete kerb stone in ZABRA Pattern) complete all as specified and directed.

Demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and directed

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for cement concrete 1:2:4 (20mm graded stone aggregate) as in Coping, Roof covering laid in slope, Holdfast including necessary formwork and weathering, slightly rounded or chamfered angles and throating, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar. Note : Work will be in patches or in bulk

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and patter

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete