8482 REPAIR AND MAINT OF DRAIN FENCING BOUNDRY WALL HARD STANDING PATH ETC ENGINEER MESS GOD FREY CLINIC ETC UNDER AGE BR I UNDER GE NW KUNJALI AND DAY TO DAY MAINTENANCE OF CE OFFICE ENGINEER MESS AND GODFREY CLINIC UNDER AGE BR I UNDER GE NW KUNJAL

Amount

Resecuring and refixing in same opening without taking down of chowkats or frames with shutter (Without taking off from frame) but n.exc 1.5 sqm complete all as specified and as directed by EIC.

Resecuring and refixing in same opening without chowkats or frames with shutter exc 1.5sqm but n.exc 4 sqm each but (without taking off shutter from the frame) complete all as specified and as directed by EIC.

Taking down chowkats or frames with shutter (Without taking off from frame) but n.exc 1.5 sqm complete all as specified and as directed

Taking down chowkats or frames with shutter exc 1.5sqm but n.exc 4 sqm each but (without taking off shutter from the frame) complete all as specified and as directed by EIC.

Taking down shutters of any description exc 1 Sqm but nexc 2 sqm complete all as specified and directed.

Ditto all as per Sr. No 5. but exc 2 Sqm each complete all as specified and directed by EIC.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by EIC.

M&L for Framed work such as grills, gratings, sun shed etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars, barred iron doors, ladders, farmed balastures, walk ways, railings, frame work of water tanks and similar work conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., of grade Fe 410 -W(Gde-E- 250) quality- A complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240. All as specified and diected.

M&L in repairs for Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hook and including scaffolding upto any height. complete all as specified and directed by EIC.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment.

M&L for Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete all as specified and directed.

M&L for preparing New or previously untreated surface of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Taking down cement plaster of any description hacking for key, racking out joints and scrubbing down with water etc to receive plaster and removing debris outside MD land incl necessary scafolding complete all as specified and as directed

M&L for Plastering 15mm thick in CM 1:6 on brick surfaces, finished with Neeru finish on walls complete all as specified and as directed .

M&L for Plastering 5mm thick in CM 1:3 on concrete surfaces as in ceiling finished even & smooth without using extra cement complete all as specified and as directed .

Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and as directed (Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound all as specified and as directed

S&F in repairs Second class hard-wood in scantlings clean swan. All as specified and directed.

S&F 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.

S&F 35mm thick factory made 2nd class HW rail & stile plain framed , panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated.

S&F 40 mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

M&L for preparation of newly plastered surfaces on ceiling surfaces and applying two coats of oil emulsion distemper over a coat of primer on ceiling surfaces incl preparation of surfaces complete all as specified and as directed

M&L for new or previously untreated surfaces of any description & applying two coats of acrylic (antifungal) exterior grade paint over one coat of primer on wall/roof complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necesssary scaffolding for high rise blds upto G+9 floor complete all as specified and as directed

M&L for preparation of newly steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and as directed

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scafolding for high rise bldgs upto G+9 floor complete all as specified and as directed

M&L for preparation of new or previously untreated surface of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

M&L for preparation of old painted wooden of any description over 10cm width or girth and applying one coat of synthetic enamel paint incl necessary scafolding complete all as specified and as directed

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

S&F in repirs 160 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, ceilings or in floor etc with and including fixing clips bends elbow, shoes bends etc (Note :- Measurement shall be taken along the centre line of the pipes) complete all as specified and as directed.

S&F 110mm dia PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls and laid in flloors/trenches.

S&F 75mm dia PVC ( SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls and laid in floors/trenches.

S&F for PVC (SWR) bends any radius 160mm bore complete all as specified and as directed

S&F 110 mm dia PVC ( SWR) grade double T/Y with access doors including fixing clips

All as per item No 38 above but 75mm dia

M&L for Plain, black, mild steel sheeting, 1 mm thick in ridges, hips, valley gutters,drip and straight flashings (length and girth as fixed)

Demolition of stone/brick masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings dressed stone work and pre cast concrete articles complete all as specified and directed.

M&L for brickwork with sub class 'B' bricks , straight or curved on plan exc 6m mean raidus built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks , straight or curved on plan to any radius in half brick thick wall built in cm 1:4.

Dismantling of Wall panelling, partition and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including Aluminium grid frame work. Complete all as specified and directed.

M&L for false ceiling made out of 600 x 600 x 4 to 6 mm thick ceiling board/tiles deep panel suspensor system made out of powder coated GI sheet main tee of size 23.50 x 40 x 0.63 mm and cross tee of size 23.50x23.50x0.63 mm and angle size 19x19x0.63 mm including 3 mm GI wire for suspending holts necessary washers nut/cleats/pin hook etc for securing frame work to ceiling to the snap grid including provn of necessary holes/cutting for providing light/far as required including making necessary recesses/projected pattern complete all as spoecified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rabbish off the premises.

M&L for (450mm x300mm ) x 7 mm thick coloured glazed ceramic tiles as in dado/vertical services set and jointed in neat cement slurry and pointed in coloured cement to match the surface incl 10 mm thick backing coat in cm 1:4 complete all as specified and directed.

M&L for preparation and applying two coat of floor/Roof paint (Make-Indigo Floor paint). All as specified and directed.

S & F Powder coated aluminium frame for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. complete shall as specified.

S&F 3 mm thick aluminium composite panel cladding plain of approved colour/shade to beam/column/slab in circular/rectangular shape including cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hollow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding etc (Note : colour/pattern of ACP sheet shall be given by GE).

S&F concealed star lock powder coated for aluminium window fixed as per manufacturers instructions all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level un re-inforced complete all as specified and directed. .

Demolition of reinforced (reinforcement cut as required to facilitate demolition) cement concrete in ground floors and paving not exceeding 15 cm thickness( below or above ground level) all as directed.

Demolition of Unreinforced cement concrete of any description and in any position not other wise specifically provided for all as specifed and directed.

M&L for mild steel TMT bars 6 to 8mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed

M&L for Hard core, broken stone/boulder, to gauge n exc 63 mm. all as specified and directed.

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundations, fillings & mass concrete etc all as specified and directed.

M&L for PCC 1:2:4 type B1 using (20 mm graded aggregate) as in kerbing all around of tile complete all as specified and directed.

M & L for cement concrete 1:2:4 type B2 (using 40mm graded stone aggretate) as in surface channel or drain complete all as specified and directed.

M&L for PCC (1:3:6) type C1 using 20mm graded stone aggregate as in coping, bed blocks etc including necessary form work complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B1 25 mm thick (using 20 mm graded stone aggregate)

M&L for PCC of type D2, 1:4:8 using (40mm graded stone aggregate) 100mm thick as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B2 using (using 20mm graded stone aggregate), 100mm thick as in flooring.

M&L for PCC 1:3:6, type C2 (using 20 mm graded stone agg) 75 mm thick as in plinth protection complete all as specified and directed.

M & L for finishing concrete road, pavement with brooming all as specified and as directed

Forming contraction (Dummy) joints 65mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and as directed

M&L for cement concrete type B1 1:2:4 (using 20 mm graded stone aggregates), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed. All as specified and directed.

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) set in cement mortar (1:6) for landings, cover slabs, manholes, chajjas, water troughs, manger shelves and similar articles with plain faces complete all as specified and as directed

Taking down 15mm bore, GI tubing and connections including cleaning for refixing or removal to store.

All as per item No 72 above but 20 mm bore GI Pipe.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

S&F 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors all as specified and directed complete all as specified and as directed.

As per item No 75 above but 20mm dia medium GI Pipe

S & F stainless steel Butt hinges of size 100 mm.

S&F Aluminium anodised sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy .

S&F aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm.

S&F Extrude aluminium anodised alloy handles, fabricated type 150mm size.

M & L for Floor door stopper of aluminium alloy body 150 mm long and tongue, anodised, with hard drawn steel spring, fixed in floor.

S&F in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and strained and fixing to any type of standard rails straining bolts, etc. all as directed.(Each line of wire to be measured)

S&F wire barbed tape concertina coil wire of 50 turn having core wire of high carbon spring steel of high tensile strength and a carbon steel strip of 20mm width, 0.5mm thick having razor sharp barbs punched tape and core wire hot dip galvanized, as fixed in repair.

Dismantling fencing wire mesh, any type all as specified and directed

S & F mild steel security chain link fencing 60mm x 60mm mesh made out of 3mm dia MS wire and 1.00mm thick PVC coating throughout fixed to RCC post including binding wire complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section including taking out embedded portion in concrete complete all as specified and directed.

S&F mild steel works as in fencing, posts & struts in fencing embedded in stone masonry/bricks works including cutting tops to shape as directed, drilled holes notching for wires flat iron fillets (for securing wire mesh etc) inlcuding all drilling, bolting or riveting etc and similar work conforming to Fe-410 or Fe-310-0 complete all as specified an directed

S&F mild steel round bars 10mm dia and over, in horizontal support for chain link straining of fencing including cut to length, bent to shape required including cranking, bending spirally for hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) complete all as specified and directed.

S&F mild steel screw bolts 10mm dia with hexagonal or square heads at one end and screwed at other ends dia of shank 5 to 10 mm and length of bolt exc. 5cm but n.exc 10cm complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

S&F Cast Iron Nahani trap 75mm, plain with grating including setting and jointing with salvant cement to waste pipe fixed in cement concrete type B1 (1:2:4) (using 20mm graded stone aggregates). All as specified and directed.

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

M&L for Chequered/cement concrete tiles 30cm x 30cm x 25mm thick set jointed and pointed in neat cement slurry in floors with in equal proportions & pigments with red and yellow colour over and including 20mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for 20 mm thick granite machine cut as in skirting/vertical surfaces i.e jambs /risers and pillars etc and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed. (colour of granite will be decided by the GE/Engr-in-Charge).

M & L for hard wear stone (of any type) granite stone slab 20 mm thick in flooring machine cut, in platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types and including 15 mm thick screed bed in CM 1:4 complete all as specified.

S & F in repairs for aluminium anodised Deco grill 7.5 mm size DG-102, fixed to F/H frames, 1.5mm thick, bar size 6.2mm and 7.5mm thick in required size complete all as specified and as directed by Engr-in-Charge.

S&F in repair 12 mm thick Prelaminated medium density fibre board both side decorative lamination interior grade, fixed in aluminium/wooden frame work complete all as specified and directed.

S&F in repair vitreous china urinal, half stall type complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet ,outlet etc complete all as specified Fixed in repairs.

S & F Vitreous china urinal partition white of size 310x700 mm slabs, terminating about 40 cm above floor line, fixed in repairs complete all as specified and directed.

S&F 32mm dia PVC waste pipe for WHB and urinals fixed in repairs complete all as specified and directed.

S&F Bathroom Cabinet Mirror 500x400 mm screwing in all conrner with chromium plated brass screws and cup washers all as specified and directed. (Make Prayag : Cat Part No 556).

S&F Push type taps for urinals, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm dia iron pipe or for brass ferrule and fixed in repairs as specified.

S&F in repairs 140mm dia overhead shower round shape single flow with air effect (ABS body & Face plate chrome plated) with rubit cleaning system.

S&F in repairs fancy type CP Pillar taps 15 mm dia, cast copper alloy , with capstan heads, screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for iron pipe and fixed complete all as specified and as directed

S&F in repairs fancy type bib taps, chromium plated cast copper alloy 15mm bore with crutch or butter fly handle, screwed down, & fixed complete all as specified and as directed

S&F in repairs fancy type angular Stop Cock valve chromium plated cast copper alloy 15mm bore with crutch or butter fly handle complete all as specified and as directed

Removing building material exc. 1.50 km but n exc. 5 km and depositing where directed

S & F in repair for health faucet ( Jet) 1 m long PVC tube with wall hook chromium plated fitted to stopcock 15 mm bore complete all as directed.

S&F in repairs 10 litres capacity PVC low level flushing cistern of approved make including ball valve,syphon set, inlet and outlet pipe, brackets etc. Complete.

S & F white glazed earthen ware vitreous Oval type china wash hand basin of size 600x700 mm with and including CI brackets, with granite including 32mm bore brass CP waste coupling Inlet/ outlet PVC flexible pipe etc complete

S&F in repairs vitreous china wash down water closet pan coloured (pedestal pattern) including plastic sheet cover with nuts and bolts etc all as specified and directed.

S&F in repairs, Plastic water closet seat, black or white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed.

SHREE JAGDISH FURNITURE CO.

MADHU ENTERPRIZES

georson constructions