Construction of Guest House/ Transit Hostel and Principal Awas at ATS Konchhabhanwar, Jhansi

Amount

Construction of Principal Awas

Cleaning of jungle including of rank vegetations grass bush wood trees and saplings of grith up to 30cm

Layout of Building

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Earth Filling By Avilable Earth

Earth work in filling under floor upto plinth including watering ramming by Cartage Earth

Sand Filling Under Floor

Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in Foundation

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in In Column G.F.

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in in Lintel G.F.

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in in Beam

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in in Slab

Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M.

Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.

25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work.up to 30.06.14

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. F.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. F.F.

12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc

6mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including supply of all Material, Labour T.&.P. complete of work G.F.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. S/L Door

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Providing & Fixing of inlet mouth of rain water pipe cost iron Greting 15 cm. diameter and weighting not less than 440gm.

Centering and shuttering including strtting, propping etc. and removel Foundations, footings etc

Centering and shuttering including strtting, propping etc. and removel Columns, pillars, Abutments, posts and struts

Centering and shuttering including strtting, propping etc. and removel Suspended Floor roofs, Landings, balconies and acces plateform with water proof pply 12mm.

Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm

Construction of Sanitary & Water Supply

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 630x450 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Stainless Steel A ISI 304 Utensel Wash kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,ncluding painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 510*1040mm bowl depth 200 mm

Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia.

90mm. Dia

Providing and fixing P.V. C. Clamp including all Material, Labour T.&P. Complete of work. For 110 mm dia.

Providing and fixing P.V. C. Clamp including all Material, Labour T.&P. Complete of work. For 90mm. Dia

Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.

Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 90mm. Dia

Providing and fixing P.V. C. N Trape including all Material, Labour T.&P. Complete of work. 90*90mm.

Providing and fixing of P.V.C. Copler For 110 mm dia.

Providing and fixing of P.V.C. Copler For 90mm. Dia

Providing and fixing of P.V.C. Covel 90mm. Ddia

Providing and fixing of P.V.C. Tee For 110 mm dia.

Providing and fixing of P.V.C. Tee For 90mm. Dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge 20 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge 25 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and Fixing of G.I. Pipe in external work 25mm. dia

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks.

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. as Such Hindwair 15 mm nominal bore.

Providing and fixing C.P. brass Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore

Providing and fixing of C.P. towel rod 24"heavy.

Providing and fixing C.P. brass Shower of approved quality as Such Hindwair

Providing and fixing C.P. brass healthfacet of approved quality as Such Hindwair

Providing and fixing C.P. brass Two way bibcock of approved quality as Such Hindwair

Providing & Placing of polyethylene waterstorage tank, ISI 12701 locking arregment and making necessary holes for inlet, outlet and overflowpipes but without fittings.

Providing & Making of Platefom for 1000 Ltr. P.V.C. Water Storege Tank.

Electrical work of Principal Awas

Wiring for light point/fan point /exhaust fan point /call bell point with 1.50 Sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable G I box and earthing the point with 1.50 sq. mm FRLS PVC insulated copper conductor single core etc. as required. Group A

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Wiring for light / power plug with 2 x 4.00 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, along with 1 No. 4.00 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required.

Wiring for light / power plug with 4 x 10.00 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, along with 2 No. 6.00 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1010 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35.00 sq. mm

Supplying and fixing 5 A to 32 A rating, 250 / 415 V, 10 Ka, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. required. Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. required. 63 Amp.

Earthing with G I earth pipe 4.5 mtr. Long 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required.

Providing and fixing 25 mm x 5 mm G I strip on surface or in recess for connections etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but modular plate etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface / recess, complete with tinned copper bes bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. required. 63 Amp.

Supplying and fixing following way surface / recess mounting, verticall type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (But without MCB and incomer) as required. 4 way (4 + 12), double door

4 way (4 + 12), TPN Vertical Type MCB/ DB double door.

Installation, testing and commissioning of ceiling fan, including wiring of the down rods of standard length (upto 30 cm) with 1.50 sq. mm, FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc.. as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230 V, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc.. as required. Upto 450 mm sweep.

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

S/F of 50 Amp. to 63 Amp. SPMCB (10 KA) Cat-B

S/F of 63 Amp. TPMCB (10 KA) Cat-B

Supply and fixing of hexagonal / round G P fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.40 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.50 mm G P sheet made upper and lower cover duly screwed fitted with 300 mm round zink coted M S bar x 12 mm and brand name should be embossed, fixing with wiring conduit laid in the R.C.C. roof before concreting along with supply of all material, labour, T&P etc. required for proper completion of work.

Supply and fixing of 16 gauge M S drum with louvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respects .

Supply and fixing of LED Tube Light with Metal heavy duty box type batten Light fitting 1 x 22 watt suitable for upto 1 x 22 watt LED Polycarbonate tube light complete including tube suitable for both surface & suspended complete in all respect With 3 years warranty.

Supply and fixing of recess/Surface mounting round 24 watt to 32 watt Cut out Min 150mm, Height Min 40mm, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24Hr Continuous Operation, complete in all respect With 3 years warranty.

Supply and fixing of water tight oblong 10 watt LED bulkhead luminaire having die cast housing with driver set confirming to IP 65 and above protection. complete in all respect. 1100 system lumens, 1101m/watt, PF>0.95, with 5 year warrantee Cat AAA

Supply & Fixing of single light wall bracket on matching M.D.F.E.G. Board base etc. complete in all respect. Cat.-AAA

Supply and fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

S/f of ceiling fan 1200 mm sweep. Single star rated Usha / Crompton/Bajaj mak

Supply & Fixing of Fan Sheet of Backelite

S/F of LED Bulb 9 watt ISI

Supply & Fixing of light duties exhaust fan (Not Fresh Air Fan) 12”dia ISI double ball bearing metalic Usha / Crompton/Bajaj/ Havells make

Supply & Fixing of exhaust fan luvers 12”dia

S/F of Kit-Kat fuse 100 Amp with neutrail link ,wooden ply board ,Hole fasner with connection

Supply of Al. Armoured Cable 16 sq.mm x 4 core.

Construction Of Guest House/Tarnsit Hostel

Cleaning of jungle including of rank vegetations grass bush wood trees and saplings of grith up to 30cm

Layout of Building

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Earth filling in under Floor By Avilable Earth including watering, Ramming Comlete of work

Supplying and Filling in Plinth with sand under Floor including Watering, ramming, consoldating and dressing complete.

Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.

R.C.C. works with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete in Foundation

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size in Super StructureIn In Column G.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size in Super StructureIn In Column F.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size in Super StructureIn In Column S.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size in Super StructureIn In Column T.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size Lintel G.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size Lintel F.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size Lintel S.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm. niminal size Lintel T.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm Beam G.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm Beam F.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm Beam S.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm Beam T.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm in Slab G.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm in Slab F.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm in Slab S.F.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all Work above plinth up to Floor V level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm in Slab T.F.

Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M. as per plinth aria.

Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.

25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work.up to 30.06.14

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. F.F.

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. S.F.

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. T.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. F.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. S.F.

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. T.F.

12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc. G.F.

12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc. F.F.

12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc. S.F.

12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc. T.F.

6mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including supply of all Material, Labour T.&.P. complete of work G.F.

6mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including supply of all Material, Labour T.&.P. complete of work F.F.

6mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including supply of all Material, Labour T.&.P. complete of work S.F.

6mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including supply of all Material, Labour T.&.P. complete of work T.F.

Providing & Laying Polished Vitrified tiles in Dado different sizes (thickness to be specified by the manufacturer) with water absorption's less than n 0.08% and conforming IS 15622 of approved make in all Colours and shades, laid on 20mm. Thick 1:4 (1cement : 4 Coarse sand) Including grouting the joints with white cement and matching pigment etc. Complete.Size 600*600 mm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) andjointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 andIS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : D/L Door

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 andIS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : Sliding Door

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 andIS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : Window

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing & Fixing of M.S. Tubler frame for Door, Window Ventilaters and copboard with rectungler / L-Type section made and MS sheet joints mitred welded and grinded finish with profiles of required size including fixing of necessary but hinges and screws and applying priming coat of approved steel primer fixing with 15x3 mm lugs 10cm long embedded in cement concrete block 15x10x10cm of cc 1:3:6 (1cement : 3 coarse sand : 6 graded stone sggregate 20mm. nominal size)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment(B) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5(1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (C)After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.

Finishing walls with 2 Coat Premium Acrylic Smooth exterior paint with Silicone additives of required shade

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

40mm. Thick Apren Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,( for payment purpose only weight of stainless steel members shall beconsidered excluding fixing accessories such as nuts, bolts, fasteners etc.). For Stair case & Ramp

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Providing & Fixing of ISI Marked Flush Door Shutters non Decoretive Type 30mm. Thick

Providing & Fixing of S.S. Door Bolt with Nuts & Screw Complete 300*16mm.

Providing & Fixing of S.S. Door Bolt with Nuts & Screw Complete 250*16mm.

Providing & Fixing of S.S.Tower Bolt with Nuts & Screw Complete 200*10mm.

Providing & Fixing of S.S.Tower Bolt with Nuts & Screw Complete 150*10mm.

Providing & Fixing of S.S.. Handles with Nuts & Screw Complete 125mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete Twin rubber stopper

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality. Providing and fixing of Lamination of door shutter.

20mm.thick 1:3 Cement: C.sand Mortor Bearing Plaster with Floting Coat of Neat Cement

Supply & Filling of Cinder in Sunken Portition of Toilet

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters With ISI marked stainless steel butt hinges of required size Second class teak wood

Centering and shuttering including strtting, propping etc. and removel Foundations, footings etc

Centering and shuttering including strtting, propping etc. and removel Columns, pillars, Abutments, posts and struts

Centering and shuttering including strtting, propping etc. and removel Suspended Floor roofs, Landings, balconies and acces plateform with water proof pply 12mm.

Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm

Sanitary & Water Supply for Guest House/Tarnsit Hostel

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 610x510 mm bowl depth 200 mm

Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia.

Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.

Providing and fixing P.V. C. N Trape including all Material, Labour T.&P. Complete of work. 100*100mm.

Providing and fixing of P.V.C. Copler For 110 mm dia.

Providing and fixing of P.V.C. Tee For 110 mm dia.

Providing and fixing of P.V.C. Door Bend For 110 mm dia.

Providing and fixing of P.V.C. Clamp For 110 mm dia.

Providing and fixing of P.V.C. Covel 90mm. Ddia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 15 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 25 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks.

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.

Providing and fixing C.P. brass long body /shortbody bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. as Such Hindwair 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore

Providing and fixing of C.P. towel rod 24"heavy.

Providing and fixing C.P. brass Shower of approved quality as Such Hindwair

Providing and fixing C.P. brass healthfacet of approved quality as Such Hindwair

Providing and fixing C.P. brass Two way bibcock of approved quality as Such Hindwair

Providing & Placing of polyethylene waterstorage tank, ISI 12701 locking arregment and making necessary holes for inlet, outlet and overflowpipes but without fittings.

For Fire Fighting

Providing & Making of Platefom for 1000 Ltr. P.V.C. Water Storege Tank.

Providing & Making of Platefom for 2000 Ltr. P.V.C. Water Storege Tank.

Providing & Fixing of Disable Toilet Kit set complete such as make Hindwair or Eq.

External Sanitary & Water Supply for Guest House/Tarnsit Hostel

Providing & Laying of 160mm. Dia P.V.C. pipe 6kgcm Sewer Line including excavation of Tranch Providing 1:4:8 cement Concrete P.C.C. Base & Pipe covered with P.C.C. 1:2:4 including all Labour, T.&P. complete of work

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc32mm.dia

Construction of 100 user Saptic tank & Soke pit (300mter Dia)

Earth Work excavation in ordaenory soil including 1.5 mtr Lift & 30.00mtr. Lead With all Labour. T&P. Complete of work

PCC 1:4:8 Cement Corse sand stone ballast 40mm size Under Floor

Class m-150 Brick Work in 1:4 Cement:C: sand Mortor Including supply of all material, Labour T.P Complete of Work in Super Structer

RCC Work 1:1:3 ( Cement: 1 Coarse sand : 3 graded stone aggregate 20 mm nominal size) in Stair case. Mumty Slab & parapet Patta including Supply of all material, Labour T.P etc Complete of work

Centring & Shutring Work Saptic tank

Centring & Shutring Work Soke pit

M.S. Work in R.C.C Work

20 mm. Thik 1:2 Cement:C. Sand mortor Plaster with Neat Cement Finish

Filling of Brick Bats in sokpit

providing and laying in cemrmt concrete 1:2:4 (1 cement 4 coarse sand 4 graded stone aggregate 40 mm nominal size) and curing complete, inlcuding cost if form-work . In foundation and floors.

Levelling & Dressing of site after complition of work

Construction of Drain 250 X 300 mm

Earth work in exacavtion in trenches for foundatione land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1:5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c With in a lead of 50m.

providing and laying in cemrmt concrete 1:2:4 (1 cement 4 coarse sand 4 graded stone aggregate 40 mm nominal size) and curing complete, inlcuding cost if form-work . In foundation and floors.

Class 150 brick work in 1:4 cement and Coarse sand of 2.20 fineness modulus mortar in foundation and plinth including supply of all material, labour and tools nd plants etc. required for proper completion of the work

Cement concrete flooring 1:2:4(1 Cement ;2 coarse sand : finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc complete

20 mm Cement plaster on singal or half brick wall finished with a floating coat of neat cement of mix : 1:3(1 cement; 3 Coarse sand)

Electrical Work of Transit Hostel & Guest House

Wiring for light point/fan point /exhaust fan point /call bell point with 1.50 Sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable G I box and earthing the point with 1.50 sq. mm FRLS PVC insulated copper conductor single core etc. as required. Group A

Wiring for twin control light point with 1.5 Sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, 2 way Modular switch, Modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Wiring for light / power plug with 2 x 4.00 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, along with 1 No. 4.00 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required.

Wiring for light / power plug with 2 x 6.00 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, along with 1 No. 6.00 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1010 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35.00 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1010 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.Above 35.00 sq. mm & Upto 95 sq.mm

Supplying and fixing 5 A to 32 A rating, 250 / 415 V, 10 Ka, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. required. Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. required. 63 Amp.

Earthing with G I earth pipe 4.5 mtr. Long 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required.

Providing and fixing 25 mm x 5 mm G I strip on surface or in recess for connections etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but modular plate etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface / recess, complete with tinned copper bes bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing following way surface / recess mounting, verticall type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (But without MCB and incomer) as required. 4 way (4 + 12), double door

4 way (4 + 12), TPN Vertical Type MCB/ DB double door.

Installation, testing and commissioning of ceiling fan, including wiring of the down rods of standard length (upto 30 cm) with 1.50 sq. mm, FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc.. as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230 V, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc.. as required. Upto 450 mm sweep.

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Electrical Work of Transit Hostel & Guest House (Market Rate)

S/F of 50 Amp. to 63 Amp. SPMCB (10 KA) Cat-B

Supply and fixing of hexagonal / round G P fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.40 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.50 mm G P sheet made upper and lower cover duly screwed fitted with 300 mm round zink coted M S bar x 12 mm and brand name should be embossed, fixing with wiring conduit laid in the R.C.C. roof before concreting along with supply of all material, labour, T&P etc. required for proper completion of work.

Supply and fixing of 16 gauge M S drum with louvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respects .

Supply and fixing of LED Tube Light with Metal heavy duty box type batten Light fitting 1 x 22 watt suitable for upto 1 x 22 watt LED Polycarbonate tube light complete including tube suitable for both surface & suspended complete in all respect With 3 years warranty.

Supply and fixing of recess/Surface mounting round 12 watt to 15 watt Cut out Min 150mm, Height Min 40mm, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24Hr Continuous Operation, complete in all respect With 3 years warranty.

Supply and fixing of water tight oblong 10 watt LED bulkhead luminaire having die cast housing with driver set confirming to IP 65 and above protection. complete in all respect. 1100 system lumens, 1101m/watt, PF>0.95, with 5 year warrantee Cat AAA

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 52 watt to 72 watt. Confirming to IP 66 protection complete in all rescept Cat-AAA

Supply and fixing of crimping, solderless, copper tin electroplated lugs of Dowells/Ismail make suitable for 1.5 sq.mm to 2.5 sq.mm cables, including tapping with insulating tape, complete in all respect.

Supply and fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of fire bucket, round bottom made of G.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge.

S&F of shock treatment chart (Prescribed under I.E Rule) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work.

Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality.

Supply and fixing of single phase multifunctional electronic energy meter 10 to 60 Amp. capacity fitted in integral box on wall complete in all respect .

S/f of ceiling fan 1200 mm sweep. Single star rated Usha / Crompton/Bajaj mak

S/F of Wall Fan 16" Usha / Crompton/Bajaj make

S/F of 'Al' Lugs & Gland complete in all respect.

Supply & Fixing of Fan Sheet of Backelite

S/F of LED Bulb 9 watt ISI

Supply & Fixing of light duties exhaust fan (Not Fresh Air Fan) 12”dia ISI double ball bearing metalic Usha / Crompton/Bajaj/ Havells make

Supply & Fixing of heavy duties exhaust fan 12”dia ISI double ball bearing metalic Usha /Crompton/Bajaj/ Havells make

S/F of Kit-Kat fuse 200 Amp with neutrail link ,wooden ply board ,Hole fasner with connection

Supply & Fixing of exhaust fan luvers 12”dia

Supply of Al. Armoured Cable 16 sq.mm x 4 core.

Supply of Al. Armoured Cable 25 sq.mm x 3½ core.

Supply of Al. Armoured Cable 70 sq.mm x 3½ core.

Fire Alarm System

Supplying, installation, testing & commissioning of manual call boxes of M.S. Construction in surface/ recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning of Fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, inatallation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuite fault, fire condition and all other standard facilities as per IS: 2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 6 Zone

Wiring for light / power plug with 2 x 1.50 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, along with 1 No. 1.50 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required.

S/F of 7 AH 12 Volt Battery. (Market Rate)

Fire Hydrant System

Supply & fixing of welding Heavy Quality Class 'C', MS pipe conforming to IS:1239 (part-1) for pipes up to 150 mm dia and IS: 3589-1991 for pipes above 150 mm including cutting, threading, welding, clamping fitting with elbow, socket nipple, clamping with MS angle iron supports and fasteners etc. also painting with red oxide and PO red enamel paint with required wrapping Coating complete in all respects. 100 mm

Supply & fixing of welding Heavy Quality Class 'C', MS pipe conforming to IS:1239 (part-1) for pipes up to 150 mm dia and IS: 3589-1991 for pipes above 150 mm including cutting, threading, welding, clamping fitting with elbow, socket nipple, clamping with MS angle iron supports and fasteners etc. also painting with red oxide and PO red enamel paint with required wrapping Coating complete in all respects. 80 mm

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying and fixing single headed internal hydrant valve With instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia With cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal /Stainless Steel cap and chain as required Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required. Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Stainless Steel (Grade 304)

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304 sheet with 3 mm dia holes with stainless steel flange 100 mm dia

Supplying (Grade and 304) fixing With orifice plate Of made required out size of 6 to mm be fitted thick tO stainless between reduce flange & landing valve of external and internal hydrants pressure at the outlet to the level of 3.5 kg/cm2 complete as required

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way - 150 mm dia M.S. Pipe

Providing, installation, testing and commissioning of non-returr valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 100 mm

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, pronze/gun metal seat, ISI marked complete with nuts bolts, washers, gaskets and conforming to 1S 780 of following sizes as required 100 mm

Supplying, fixing, testing and commissioning mmiecinning of of butterfly butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to 1S 13095 of following80 mm

Supplying, fixing, testing and commissioning mmiecinning of of butterfly butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to 1S 13095 of following 100 mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1010 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35.00 sq. mm

S/F of Air Vessel made of 250 mm dia, 8 mm thick MS Sheet, 1200 mm in Height With air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories,pressure gauge and painting with synthetic enamel paint of approved shade as required.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS: 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for pperation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F insulation, conforming to l$-325 (D) M.S. fabricated common base plate, coupling, coupling guard foundation bolts etc. as required (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head

Supplying and fixing of Pressure Switch in M S pipe line including connection etc. as required.

Fire Hydrant System (Non Scheduled Items) - Market rate

SITC of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted "FIRE" in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete.

Supply, Installation, Testing & Commissioning of Pressure Gauge.

Supply of Al. Armoured Cable 16 sq.mm x 4 core.

S&F of Fire extinguisher, ABC Type 6.00 Kg. capacity (ISI marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

S&F of Co2 type Fire extinguisher, 4.5 Kg. capacity (ISI marked IS: 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

S/F of 'Al' Lugs & Gland complete in all respect.

M/S DINESH KUMAR AGRAWAL