Construction of Warehouse at Greenfield Electronics Manufacturing Cluster (EMC) in Tuem Village of Pernem Taluka Warehouse Type A (01 number) ,Warehouse Type B (01 Number) and External work of warehouse plot

Amount

SECTION A - EARTHWORK

Clearing jungle including up rooting of rank vegetation grass bush wood trees and sapling of girth upto 30 cm. measured at a height of 1 m above ground level & removal of rubbish upto a distance of 50 mt. outside the periphery of the area cleared. (if however, only grass is met with the area will be measured and paid for under item 4001).

Earthwork in excavation over areas (exceeding 30cms in depth, 1.50m in width as well as 10sqmts on plan) in all types of stratas comprising of any type of materials such as soil, silt clay, sand, gravel, murrum of all types of conglomerates, laterite rock, soft rock, ordinary rock, disintegrated rock, fissured / shattered rock, decomposed rocks, weathered rock, etc and all such other materials either in full or part as the case may be adopting any method / methods as may be convenient or permitted including chiseling, wedging etc. in all conditions such as dry, moist, foul, saturated, submerged etc as directed by Engineer etc. all complete including refilling, dressing of sides, ramming of bottom, including all lead and lift, including getting out the excavated soil as directed including pumping and bailing out water, barricading danger, lightening, guarding as directed by Engineer upto depth of 1.5m (Blasting Prohibited).

Earthwork in excavation over areas (exceeding 30cms in depth, 1.50m in width as well as 10sqmts on plan) in all types of stratas comprising of any type of materials such as soil, silt clay, sand, gravel, murrum of all types of conglomerates, laterite rock, soft rock, ordinary rock, disintegrated rock, fissured / shattered rock, decomposed rocks, weathered rock, etc and all such other materials either in full or part as the case may be adopting any method / methods as may be convenient or permitted including chiseling, wedging etc. in all conditions such as dry, moist, foul, saturated, submerged etc as directed by Engineer etc. all complete including refilling, dressing of sides ramming of bottom, including all lead and lift, including getting out the excavated soil as directed including pumping and bailing out water, barricading danger, lightening, guarding as directed by Engineer. Extra for additional depth of 1.5m or part thereof (Blasting Prohibited).

Earthwork in excavation in foundation, pipeline trenches, drain (not exceeding 1.5m in width or 10 sq.m. on plan) in all types of stratas comprising of any type of materials such as soil, silt clay, sand, gravel, murrum of all types of conglomerates, laterite rock, soft rock, ordinary rock, disintegrated rock, fissured / shattered rock, decomposed rocks, weathered rock, etc and all such other materials either in full or part as the case may be adopting any method / methods as may be convenient or permitted including chiseling, wedging etc. in all conditions such as dry, moist, foul, saturated, submerged etc. as directed by Engineer etc. all complete including refilling, dressing of sides, ramming of bottom, including all lead and lift, including getting out the excavated soil as directed including pumping and bailing out water, barricading danger, lightening, guarding as directed by Engineer upto depth of 1.5m (Blasting Prohibited).

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth outside the premises in the dumping ground approved by the Corporation and as directed by Engineer in Charge.

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete : murrum

SECTION B - LATERITE MASONRY WORK

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Available on site

SECTION C - BRICK MASONRY WORK

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 coarse sand ) in foundation and plinth size of blocks (30 x 23 x 15)

Brick work using fly ash bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with bricks of class designation 40 kgs / cm2. in superstructure upto floor five level. : 230 x 110 x 80 mm

SECTION D - PLAIN CEMENT CONCRETE

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

SECTION E - FORMWORK

Centering & shuttering including Strutting, Propping & removal of forms for :

Foundations, Footings, Bases for columns

Vertical surfaces such as retaining walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Columns, Piers, Pillars, Abutments, Posts and struts (square rectangle polygon in plan)

Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, bressumers and Lintels, chajjas, sills, plinth beams not exceeding 1m in depth

Suspended floors, roofs landings, shelves & their supports

SECTION F - REINFORCED CEMENT CONCRETE

Providing and laying in position machine batched concrete (BMC), machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering , shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing the strength and durability as per the direction of the Engineer-in-charge. M25 grade of reinforced cement concrete by using 410kg of cement per cu.m. of concrete. All works upto floor V level. (Note:- RMC Can be accepted if required by the contractor, But without any additional financial Implications)

Providing and laying in position machine batched concrete (BMC), machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering , shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing the strength and durability as per the direction of the Engineer-in-charge. M25 grade of reinforced cement concrete by using 410kg of cement per cu.m. of concrete. All works upto floor V level. M-30 grade concrete by using 420kgs of cement per cu.m. of concrete instead of M-25 grade of B.M.C. (Note:- RMC Can be accepted if required by the contractor, But without any additional financial Implications)

Vaccum dewatering of laid concrete for roads / areas using Tremix machinery including formwork with MS channel/ angle sections on sides of concrete with proper supporting system, surface/screed & needle vibrating & levelling of concrete. Vaccum dewatering should be done using suction mats (spread on surface) & suction pump, power floating/ trowelling using screen floater, manual spreading of hardening compound (if any), smooth/rough/broom finish to the required slope, camber & level, groove cutting (upto 10mm wide x50mm deep) for contraction/expansion, construction & longitudinal joints, Providing dowel bars with sleeve/tie bars, filling two component polysulphide sealant/joint filler (Bitumen hot sealing compound: Grade A), taping with masking tape etc complete. (Concrete, reinforcement, Dowel Bar with sleeve/tie bar Reinforcement, tarpaulin sheet to be paid separately)

SECTION G - STEEL REINFORCEMENT & STRUCTURAL WORK

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work ,cutting, hoisting, fixing in position including bases & gussets plates, holding down bolts with nuts & washer and applying priming coat of red lead paint: In tees, angles, flats and channels, tubular sections inclusive of application of three coats of marine paint of approved shade and brand or epoxy painting using Nitocote ET 550 /ET 140 (Fosroc) with prior approval, to steel work as per manufacturer's specification approved by the Engineer.

In tees, angles, flats and channels

Providing & fixing in position polyster powder coated hand rails in staircase, landing, external passages and the like with 2" dia G.I. pipe (light class) resting on 25 mm (1") size M.S. square bars of clear height 90cms placed at 30 cm c/c including making necessary hold fast fixture (25 mm square bars 22 cm long) embedded in concrete for resting the M.S. vertical square bars with holding etc. as required for the work including bending hand rail pipe to proper shape in curves with specials etc. complete(measurement will be made along the running length of hand rail)”

SECTION H - PLASTERING, PAINTING, ROOFING & FLOORING

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

12mm cement plaster 1:4 (1 cement : 4 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand), grooves as per design, finished with sponge.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acrylic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), High strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Providing and fixing colour coated Galvalume roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Supplying and Providing in position under deck 50mm thk non combustible Glass wool insulation 24 kg/m3 density with white prelaminated polypropylene facing (WMP-50) under the metallic roof complete for sound and heat insulation including cost of GI welded mesh of 75x75x1.60 thk stretched over purlin complete. The GI Welded mesh should be primed and painted with min. 2 coats of superior quality ready mixed paint for steel work

Providing & Fixing turbo Ventilator on Roof as per drawing & to the requirement to Correct Location & line & lvl as per site condition Turbine Dia - 28 Inch (760mm); Neck/Throat - 24 Inch (610mm); Height - 18 Inch (460mm); Vanes(Blades) - 42 Vanes , Aluminum 0.5 mm thickness Alloy 8011; Base Ring MOC (Mounting ring) - Stainless steel ; Top Plate MOC - Stainless Steel 0.8 mm thickness; Rotation - Twin Sealed 6203ZZ bearings with self lubricating Dupont Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity Twin Sealed 6201ZZ bearings with self lubricating Dupont Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity. Centre shaft - 18mm high carbon steel zinc plated.; Inner Arms - M.S. with electro zinc plating; Outer Arms - M.S. with electro zinc plating; Frp base plate - 2 mm thick clear 1.020 mtr wide and 1.65 mtr long matching your sheet profile. Weight 8 kg(Approx); Weight - 6.5 Kg approx; Center Width - 800mm ± 5 mm; Dia of Bottom Ring - 600mm ± 15 mm; Nos of Bearing - 02 Nos; Bearing Type - SKF – 6001 ZZ & 6003 ZZ Permanently Lubricated & Sealed; Rivets - Aluminum Alloy with Washer

Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately

Extra for crimp curving for curved 0.5mm TCT Galvalume/Zincalume sheets.

Providing & fixing in position Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yield Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS-3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed.

Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S. top cover of 1.25mm thick for folling shutterstop cover and spring.

Providing mechanical device, chain and crank operation for operating rolling shutters. : Exceeding 16.80 sq.m. in area Chain & overhead operation

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. Dark & Light Shades

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete. : 600 x 600 mm - Dark & light Shades

Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete :

600x 600 mm light and dark Shades

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm : Jet Black

SECTION I - DOORS & WINDOWS

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. : with 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Wood Finish Wood Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wooden styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) and printed matt having wooden textures used along with UV Resistant resin to give the clear texture on the door. The core of shutter will be filled with MR 2nd grade Block Board. The Shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories - i) S.S. Hinges 4 " - 3 no, ii) S.S.latch - 1 no, iii) Tower Bolt 5 " - 2 no, iv) Handle 5 " - 2 no : Shutter Thickness - 40 mm

FRP (Fiber Reinforced Polymer) Frames with Wood Finish Manufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2008 certified company : Specified Cross Section of 4” x 2 ½ “

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol& II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with three sliding shutters using 18 mm series shutters section and Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section. (b) Plain glass

Providing and fixing powder coated aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vole & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge and Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section: Adjustable louvered windows - Figured glass

SECTION J - MISCELLANEOUS WORK

Providing preconstruction anti – termite treatment to the buildings conforming to I.S.S. 6313 part II 1971 (revised) including adopting the precautions for health hazards and safety measures as mentioned therein with the cost of all materials chemicals, plants, equipments etc. required for the treatment and furnishing a guaranty for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. The payment will be made on plinth of the building. (a)pre-construction as approved by Engineer

Spray applied fast curing, heat resistant polyurethane seamless waterproofing membrane Providing and applying on a well prepared horizontal surface Coniroof 2111 of BASF make or equivalent Supply and Installation of BBA Approved spray applied waterproofing membrane system, a multi-layered system comprising, primer, waterproofing membrane. The product shall have the green label certificate. The primer shall be CONCRESSIVE 2525 or equivalent, a two component, solvent free epoxy resin based. The fast-drying primer shall be CONCRESSIVE 2525 or equivalent, a two component, solvent free epoxy resin based. It shall be formulated to meet the requirements of non tainting for usage in food storage and potable grade structures. It shall be fully compatible with CONCRESSIVE Range of repair mortars. Dried, graded MASTERTOP SRA no. 3 sand or equivalent is immediately and evenly spread over the entire wet surface by hand or mechanically. When sufficiently cured the surface is vacuumed to remove any loose sand. Waterproofing Membrane: The waterproofing membrane shall be CONIPUR M 800 or equivalent, a solvent free two component spray applied system. Ladders supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete.

It is highly reactive and can only be applied by special, two component spray equipment. UV Top Coat: The top sealer for use on exposed areas shall be Conipur TC459 or equivalent based on aliphatic polyurethane, pigmented, single component; moisture curing, UV and weather resistant. Conipur TC459 or equivalent should be stirred well and applied evenly by spraying. The rates are inclusive of labor, tools and tackles. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete.

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of approved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manufactured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. : 80 mm thick in all colours except grey (M40 grade)

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Directorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification.: Size 30 cm L x 50 cm H x 15 cm T

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces as per MORTH Specification 803

Painting (two or more coats) with black anticorrosive bitumastic paint of approved brand and manufacture on new work to give an even shade.

SECTION K - PLUMBING & SANITARY WORK

Fixing water meter & stop cock in G. I. Pipe line including cutting & treading the pipe and making long screw etc. complete (cost of water meter and stop cock to be paid separately)

Proving and fixing white vitreous China water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cistern (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fittings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required. : Orissa pattern W.C. pan

Proving and fixing white vitreous China Wall Hung type (European Type) water closet with seat and lid with C.I. brass hinges and rubber fittings with flush valve nelson/ similar fully chromium plated with stop cock, wall flanges, flush pipe or elbow and vaccum breaker coupling etc. including chair bracket/rag bolts, cutting & making good the walls and floors Each 8735.00 212 where required and concealed seat support - W.C. Pan with white plastic seat and lid

Providing and fixing white vitreous China flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm sizes respectively with PVC automatic flushing cistern with fittings, R.S. or C.I. brackets, standard size galvanized steel flush pipe and spreaders with brass unions & G.I. clamps complete, including painting of cistern and fittings, cutting and making good the walls and floors where required.: a) One urinal basin with 5 litres p .v .c. automatic flushing cistern

Providing 20mm thick marble slab to urinal partitions with cement complete

Supply and fixing of under counter type of approved make wash basin, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including with approved mirror polish granite top in single piece & for sides in single piece over average 40 mm thick cuddappa supporting top slab, 25 mm nosing and rounding of granite top and sides, inclusive of sandwitched partitions of 25 mm thick cuddappa slabs using cement slurry or equivalent, cut out of required sizes to receive fittings an pipes , chasing in walls and making grooves etc complete ( Rate quoted per unit of wash basin complete in all respects)

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993 :15mm nominal bore

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainless steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing toilet paper holder :C.P. brass

Providing & fixing liquid soap container with C.P. brass lid and brackets fixed to wooden cleats with C. P. brass screws : Glass container

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Proving and fixing multi-connection floor trap (deep seal) with 150 mm x 150 mm square S.S grating with anti-cockroach trap assembly for above ( deep seal ).

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with sheet flange, Jaquar make or equivalent. Confirming to IS 8931;1993 : 15 mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :

20 mm nominal bore

25 mm nominal bore .

Providing and fixing rigid PVC S.W.W.(Soil, waste & rain water) drainage pipes of approved make including lubricants etc. complete ( single / double socketed)

110 mm dia

75 mm dia

Providing and fixing rigid PVC bend for ( of approved make) for S.W.R. drainage pipes of approved make including lubricants etc. complete bend with door

110 mm dia

75 mm dia

Providing and fixing RPVC vent cowl

110 mm dia

75 mm dia

Providing and fixing Single Tee of rigid PVC for ( of approved make) for S.W.R. drainage pipes of approved make including lubricants etc. complete with door

110 mm dia

75 mm dia

Providing and fixing Single "Y " of rigid PVC for ( of approved make) for S.W.R. drainage pipes of approved make including lubricants etc. complete with door

110 mm dia

75 mm dia

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc

15 mm nominal outer dia CPVC pipe

20 mm nominal outer dia CPVC pipe

25 mm nominal outer dia CPVC pipe

Providing and fixing 40mm dia G.I. pipes outlet in cement mortar 1: 3 (1 cement : 3 fine sand) including cutting and making good the wall.

Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design.

Providing and fixing non return valve of approved quality :32 mm nominal bore

Providing and fixing rigid PVC S.W.W.(Soil, waste & rain water) drainage pipes of approved make including lubricants etc. complete ( single / double socketed)

160 mm dia

Providing and fixing rigid PVC bend for ( of approved make) for S.W.R. drainage pipes of approved make including lubricants etc. complete bend with door

160 mm dia

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

Inside size 90 x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg.)

Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Extra for depth for manholes : a) size 90 x 80 cm

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per directions of the Engineer in charge.(External work (heavy duty SDR 11 pipe) : 32 mm nominal outer dia pipes.

SECTION L - ELECTRICAL WORK

Wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in PVC casing caping with modular switch, modular plates, suitable size modular surface box of specified Category and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. (a) Group A -- with Cat C Modular Accessories

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in PVC casing caping with 2 way modular switch, modular plates, suitable size modular surface box of specified Category and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. (a) with Cat A Modular accessories (b) with Cat C Modular accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in PVC casing capping and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Wiring for 5A /15A plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in PVC casing capping along with 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent PVC casing capping of appropriate size as required. (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire (20mm casing )

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent PVC casing capping of appropriate size as required. (d) 2 x 6 sq.mm + 1 x 6 sq.mm earth wire (25mm casing )

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent PVC casing capping of appropriate size as required.(j) 4 x 6 sq.mm + 2 x 6 sq.mm earth wire (32mm casing )

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent PVC casing capping of appropriate size as required. (k) 4 x 10 sq.mm + 2 x 10 sq.mm earth wire (32mm casing )

Telephone Wiring

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wall or in the existing surface/recessed steel/PVC conduit having following pair(s), complete as required. '(a) 2 Pair

Supplying and drawing/fixing jelly filled outdoor type armoured telephone cable with 0.5 sq.mm dia. tinned copper conductor, ITD/DOT approved, with GI saddles on wall or in the existing surface/recessed steel/PVC conduit having following pair(s), complete as required. (a) 5 Pair

Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone make modules, crimping and terminations, etc. complete as required.''(a) 10 Pair

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required. '(b) Cat 6 +

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 450x550x367 mm) as per specification No. WG-NAS/RAK

Supplying and fixing of following sizes of PVC casing caping along with accessories on surface as required. (a)20mm casing capping

Switches and sockets

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. (b) Cat C

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (b) Cat C

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT B

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT B

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sun mica board

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. ''(b) Cat C

DB and MCB

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper bus bar neutral bus bar earth bar din bar detachable gland plate interconnections phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (g) 6 way (4+18), double door, Horizontal type Cat B

Supplying and fixing following way TPN sheet steel, double door, Vertical type MCB distribution board 415 V on surface/ recess complete with tinned copper bus bar neutral bus bar earth bar din bar detachable gland plate interconnections phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and bus bars of following ways (but without MCBs as required). (e) 8 way (8+24), double door, Vertical type, Cat B

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required. (f) SP, Cat B

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required.(j) TPN, Cat B

Supplying and fixing 20 A 240 V SPN industrial type socket outlet with 2 pole and earth metal enclosed plug top along with 20 A, C series SP MCB in sheet steel enclosure in surface or in recess with chained metal cover for the socket outlet and complete with connections testing and commissioning etc. as required" '(b) Cat B

Indoor Fixtures

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (c) Cat C

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel up to 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Providing and erecting air circulator 600 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for 230/250 volts single phase, 50 cycles A.C. supply, core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation

Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting high bay LED fitting IP 65 with lamp 70W-80W, PF >0.95 duly connected complete with accessories as per specification no. FG-ODF/LED

Outdoor Fixtures

Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB

Supplying and erecting LED street light fitting suitable for above75W - 90W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No. FGODF/ FLS2.

Supplying & erecting FRP box of size 150 x 125 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. CB-SB

Cables

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. ' 3 Core 2.5 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.(1) 3 x 1.5/2.5 Sq. mm.

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 Core 16 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (5) 4 x 16 Sq. mm.

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 Core 25 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge, sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project at least 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. In all type of strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm in the existing masonry open duct, etc. complete as required

Supplying and making cable end terminations with brass compression gland and aluminium lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.(6) 4 x 25 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet)

LT Panels

MAIN PANEL - Supply ,installation testing and commissioning of indoor , IP54,duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint, LT panel ,floor mounted , single front ,14 G. MS CR Sheet fully compartmentalised, all MCCBs, Disconnect or fuse switch unit, MCB's etc. with rotary handles, terminal spreaders for use on MCCB incoming and outgoing terminals, separate bus bar 300A and cable chambers with cable entry at top/ bottom as required.

Incomer Surge arrestor/ surge protection device 2 tested for Imax 15 kA for three phase and neutral - 1No. 100A Adjustable 35/40 KA, CAT A - 1 No Metering Electricity Department Approved Three phase LT CT multifunction energy meter of accuracy of class 0.5, - 1 Nos Outgoings 6 A to 32 A, C series MCB TPN, Cat A - 5 Nos 40A, C series MCB TPN, Cat A - 1 Nos

Earthing

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge. The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid separately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonry chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the piping)watering arrangement(plumbing will be paid separately). in all type of strata

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge. The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid separately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonry chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid separately). In all types of Strata

Extra for using salt and charcoal for pipe earth electrode as required ( 65 Kgs of Charcoal and 5 Kgs of Salt).

Extra for using salt and charcoal for GI or copper plate earth electrode as required( 96 Kgs of Charcoal and 5 Kgs of Salt)

Supplying and laying 25 mm x 5 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for connections etc. as required

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required

Cable Tray

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.100mm width x 50mm depth

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.200mm width x 50mm depth

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.300mm width x 50mm depth

Supplying and Installing following size perforated type 14 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 450mm width x 50mm depth

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 100mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 200mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 300mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 450mm width x 50mm depth (14 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 100mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 200mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 300mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 450mm width x 50mm depth (14 SWG)

Laying of Cables

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge, sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project at least 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. In all type of Strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required

Cable End Terminations

Supplying and making cable end terminations with brass compression gland and aluminium lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.'(5) 4 x 16 Sq. mm.

Poles with Bracket & Fittings

Providing & erecting 7 m high galvanised conical pole with foundation bolts having bottom dia. 145 to 175 mm, top dia. 65 to 75 mm on provided foundation as per specification no. OHPL/ CPL

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OHPL/ PBKT

Supplying and fixing 0.5 A to 5 A rating, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required"(f) SP, Cat B

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supplying & erecting mains with 3x2.5 sq.mm FRLHS copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WGMA/ BW

Street Light Panel

TANMAY KHOLKAR

M/s. R. Z. Malpani

INDAGE DEVELOPMENT CONSTRUCTION PVT LTD