Interior and Fitout work for IIAC at 4th and 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BILL OF QUANTITIES (BOQ)

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji

Nagar, New Delhi

Amount (In Rs.)

S No. Particulars

1 CIVIL & INTERIOR WORKS 11,219,584.03 67,699,960.75

3 PLUMBING & FIREFIGHTING WORKS 5,899,750.80 1,011,737.01

4 FURNITURE 33,410,448.70

7 Grand Total 316,486,727.53

7 Grand Total 316,486,727.53

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

Summary of Civil and Interior Works

S.No. Description of Works Amount (SR, in Rs.)

1 Masonry & Plaster 2,568,487.30 125,136.71

3 Partitions & Wall Cladding 1,835,546.60 25,341,838.76

6 Finishes & Miscellaneous 656,742.10 9,875,366.96

Total cost of DSR Items(Correction Factor @0.973) 11219584.03

GRAND TOTAL (Carried Forward) 78,919,544.78

GRAND TOTAL (Carried Forward) 78,919,544.78

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

CIVIL & INTERIOR WORKS

2 MASONRY AND PLASTER

Providing and laying in position cement concrete of specified grade excluding the cost of centering

and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40

mm nominal size derived from natural sources)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

2.2 11.3 floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 981.00 614.20 602,530.20

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 310.00 1,123.80 348,378.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick

2.5 13.2 CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.

2.6 13.4 12 mm cement plaster of mix

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth

2.7 5.3 level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with CUM 0.60 11,505.50 6,903.30

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20

mm nominal size derived from natural sources).

2.8 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

2.9 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 12.00 736.40 8,836.80

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete above plinth level.

5.22A.4 Hot rolled deformed bars kg 90.00 107.85 9,706.50

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick POP Punning over

cement plaster in line & plumb finished smooth to receive paint. (Internal surfaces of walls).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of

slurry of cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This

2.12 22.5 layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed SQM 70.00 617.05 43,193.50

with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4

hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and

sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

AAC BLOCK FILLING: Providing and Laying of AAC Block Filling in the Slab Sunk or Raised Areas as a

Back fill or platform. Laying should be done in layers with pounding done at every level to ensure a

proper cavity free installation without disturbing any existing services in the area. Cost to also include

haunching for plumbing pipes.

SUB TOTAL OF MASONRY AND PLASTER 2,568,487.30 125,136.71

3 PAVING AND WET WORKS

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

3.1 8.31 green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over SQM 120.00 1,267.95 152,154.00

12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

3.2 11.41A sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and

matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of

tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and

rubber mallet for placing the tiles gently and easily.

11.41A.2 Glazed vitrified floor tiles polished finish of size

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be

specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours,

3.3 11.40 shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement SQM 24.00 1,439.40 34,545.60

: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white

cement and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of upto 5 mm width, using epoxy grout mix of 0.70 kg of

3.4 MR organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /

grouting and finishing complete as per direction of Engineer-in-charge.

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In

3.5 MR Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with RMT 1,400.00 360.35 504,496.51

Rubber/ PVC Jointers and Gasket.

Providing and fixing removable raised/false access flooring with system and its components of

approved make for different plenum height with possible height adjustment upto 50 mm,comprising of

3.6 11.54 modular load bearing floor panels supported on G.I. rectangular stinger framework and G.I. Pedestal

etc. all complete, as per the architectural drawings, as specified and asdirected by Engineer-in-charge

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI

Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal

head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base

plate using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid,

rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

between the bottom of the floor for electrical conduits and wiring etc. all complete as per the

architectural drawings, as specified and as directed by

the Engineer-in-charge

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with

an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of

Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each

dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust

protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible

Portland cementitious core mixed with lightweight foaming compound. The access floor shall be

factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness

for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated

Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is

placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum

1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers

specification and as per the direction of Engineer-in-charge. All specification must be printed on the

side of the panel to ensure the quality of the product.

11.54.1 300 mm Finished Floor Height (FFH) SQM 45.00 5,623.95 253,077.75

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Supply of modular carpet of approved model and shade and made with 100% nylon 6/6.6 tufted

textured tiles/ plank of all sizes as approved, stain resistant, anti microbial, and having colour fastness to

water, fastness to light, rubbing fastness and castor chair suitability as per relevant standard for heavy

commercial usage, with 100% PVC free Backing with having average density 6000 oz/cu. yd. or

more,Nominal total thickness of 5.9mm, and Pile weight – 16-18 oz/ sq yard. Material shall be CRI GREEN

LABEL PLUS certified, and shall have recycled content complying to GRIHA requirement, including fixing

with GRIHA compliant adhesive of approved make, minimum 15 years manufacturer's warrantee, all

complete as per drawings, manufacturer's specifications and direction of Engineer in Charge

Providing and Fixing of 15mm thick Engineered Woooden Flooring with plank width of 135/185mm and

length of 1800/2100mm and top layer up to 3mm in approved finish. Surface of Top layer shall be pre

finished with several layer of UV hardened Acrylic lacquer. The product shall be Free from

Formaldehyde and solvents. Flooring plank shall be interlocked using Plank locking system in a glue less

3.8 MR floating manner. Engineered wood planks shall be a composition of 3 layer of Pine wood with direction SQM 945.00 8,839.43 8,353,262.21

of each layer oriented at right angle to the adjacent layer of natural strain in Lacquer and Beveled in

length and width as specified by the manufacturer-in-charge. Product shall be MAKE IN INDIA. The cost

to include providing and fixing of all acessories i.e Skirting, beading, profile etc. and Underlay 2mm PE

foam and polythene combo with 40 Micron complete as required.

TOTAL FOR PAVING & WET WORKS 5,361,294.15 9,854,311.83

4 PARTITIONS AND WALL CLADDING

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I. frame and

required board, including providing and fixing of frame work made of special section power pressed/

roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling

channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at

the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or

suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange

of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling

channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including

fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal

screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of

frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300

mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads

at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum

(GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall paneling using board

of required thickness fixed on the ‘W’ profile (0.55 mm thick ) having a knurled web of 51.55 mm and

two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having

one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27

4.2 9.133 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with

fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk

ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-

incharge, the joints of the boards are finished with specially formulated jointing compound and 48 mm

wide jointing tape to provide seamless finish.

9.133.3 Plain Gypsum plaster board conforming to IS: 2095 Part -1:2011 (Board with BIS certification marks)

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk. Glass with anodised

Aluminium frame fixing glass with snap on option consisting of top, bottom and side frame measuring

40-46mm x 18mm-26mm complete with glazing rubber as per manufacturer's specifications and

4.3 MR instructions of Engineer- in-charge. Rate include supply & Installation of 12 mm thk toughened glass SQM 75.00 6,015.51 451,163.15

with double sided adhesive tapes for glass to glass butt joints. Partition system from FFL to False Ceiling

level, inclusive of cost of support required for fixing in the ceiling. The frame to be powder coated in

desired shade as per the instructions of the Architect.

Providing & Fixing of double glazed modular system consists of Aluminium section of 30x75x1.5mm thick.

All sections duly anodised up to 20-25 microns with 6063-T6 grade and required accessories i.e. glass to

glass aluminium I/H sections, T section & 90 degree L sections & Glass packing to adjust the floor level.

Ceiling profile, Floor profile and wall profile are 30 mm visible face and 75 mm wide with 2 Layers of 10

mm toughened glass & insertion of Thermoplastic gasket to adhere the glass firm & airtight. The sound

reduction Value is from 42 to 45 Db complete in all respects as per instruction of engineer-in-charge.

PARTITIONING - Partition using 12mm thick HDHMR fixed on both sides on aluminium Studs Frame 50mm

x 50mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm c/c in

both directions. Aluminuim frame to be fixed to floor and RCC Ceiling using fastners. The cost to

include finishing visible edges with 12mm thick mdf strip as per detail drawings.

PANELLING- Panelling using 12mm thick HDHMR fixed on one side on Aluminium Frame 50mm x 25mm x

4.6 MR 1.5mm as per approved sample and architectural drawings placing the same 600mm c/c in both SQM 1,395.00 2,477.47 3,456,066.00

directions. Aluminuim frame to be fixed to walls, floor and RCC Ceiling using fastners.

Supply and cladding using 12mm thick HDHMR on existing frame/ surfaces in CNC cut letters/ patterns

as per design and approvals.

Supply and cladding using 12mm thick HDHMR on existing frame/ surfaces in strips upto 200mm wide as

per design and approvals.

1200mm high paneling in 2 layers of 6mm thick bendable ply including aluminium frame as per general

paneling specification.

Supply & Installation of solid manual Operable Acoustic Partition consisting of series of 100 mm thick

individual movable elements travelling along the ceiling track assembled to form a solid wall. The entire

system must function as a solid wall and even when closed should reveal minimal screws, fixing or other

similar solid metal parts. The sound insulation of the operable partition should be 50dB tested under third

party reputed laboratory in accordance to EN 20140-3. The test certificate should show the make and

model of the system.

Elements must be constructed of a torsion-free steel horizontal tube frame and torsion-stiff vertical

aluminium profiles, bolted together to make the element strong and sturdy. The frame must be clad

either side with 16mm MDF panels hung in acoustic free suspension from the panel frame. The panel

skin shall be installed on site and able to be replaced without totally disassembling the panel frame.

The element must be constructed in accordance with the specified sound insulation requirements. The

elements must be inter-connected by means of a positive locking concave/convex aluminium profile

with an integrated magnetic strip and sealing lip having a linear attraction of 40N/m. The spindle

mechanism in every element should be connected to the top and bottom horizontal seals which

should be constructed of aluminium plates with flexible rubber at the contact point. Specially formed

polyurethane corner rubber seal to be provided for overlapping acoustic seals horizontal sealing strip.

Each element must have a spindle mechanism which should be connected to the spring loaded top

and bottom retractable seal. The spindle mechanism should be operated manually by a bayonet

connected crank handle that acts as a lock in function during cranking process. The horizontal top and

bottom seals must be retracted as per the operating mechanism and should ensure a contact pressure

of 800N when the seals are completely extended. The spring loaded retractable horizontal seals should

also be able to adjust to minor floor undulation for better accoustic efficiency. The seal spindle

mechanism must be accessible while the panel is hanging for servicing and adjustment if necessary.

Total disassembly of the panel frame to access internal components is not acceptable. No fixed sweep

seals allowed in top and bottom of the element that would rub against the track or floor while moving

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

The telescopic element or the end closure element must open and close 120mm horizontally through

an additional telescopic panel made of 16mm MDF provided and fixed to the telescopic element. The

movement of the telescopic panel and the operation of the horizontal top and bottom seal and must

be operated by a single mechanism. The telescopic element must maintain all the same quality criteria

as the other elements.

Sound Baffle/Barrier above Operable Partition

After installation a sound barrier is erected between the false ceiling and the RCC ceiling using two 12.5

thick gypsum boards on each side of the track filled with a mineral wool mattress and fitted to a G.I.

sheet framework. All cracks, joints, openings are caulked with special compound and taped over to

form a solid wall of the same STC as of the partition. The efficiency in sound insulation of a partition

depends on its installation, which has to be done in order to achieve the same insulation coefficient

above the false ceiling as that of the movable wall.Entire work to be done as per drawing,

specifications and as per directions of Engineer-in-charge.

VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative/ Natural Veneer of approved design

and shade, cladded on to existing surfaces. (base rate Rs. 1750/- sqm)

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade

texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of

160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st

coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove

excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied

with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be

allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to

dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and

melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is

again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is

applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed

in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2

layers without gap of time.)

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing Plywood

Providing and fixing of 1.25mm thick high pressure decorative laminates (conforming to applicable

IS:2046-1995, EN 438-3: 2016, NEMA LD3-2005 quality standard), made out of urea free, thermosetting

phenolic resins treated Kraft papers as core material and Amino plastic resin treated decor papers on

the finish surface.

Performance properties of laminates must meet having a minimum density of 1.35g/cm3 and possess

Anti-viral, Anti-Fungal & Antibacterial properties and fulfil the criteria of FSC, Greengard-Gold, GRIHA &

GreenPro certification. Surface of laminates accomplice the properties as per classification HGS Grade

for Resistance to surface wear (350 revolutions), Resistance to cigarette burns (Rating-Not worse than 3)

, Resistance to staining(Rating 5), Resistance to dry heat @180°C (Rating 4), Resistance to cracking ( >4

rating) & Resistance to scratching(>2.0 N) . Resistance to Color Change-Xenon Arch Lamp (Rating

Color/Decor, size and finish of laminates should be agreed and finalized under direction of the in-

charge. The cost to include pasting over 4 mm thick MDF and fixing on existing surfaces as per

directions of engineer-in-charge.

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS:

8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh

screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per

directions of Engineer-in-Charge.

Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and

length 2400 mm or as specified by the Architect/ approving engineer, made of a high density fibre

board with minimum 725 Kg/M3 density substrate with a laminated facing as per the approved shade

& finish and a melamine balancing layer on the reverse side. The boards shall have a special

perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and

5mm/13mm/21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to

4.16 MR receive special clips for installation. The back of the perforated panel shall have sound absorbing non- SQM 360.00 4,544.09 1,635,872.90

woven acoustical fleece having NRC of 0.52-0.63. The panels shall be mounted on special aluminium

splines using clips. The works to be done complete as per drawings and satisfaction of engineer-in-

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Providing and supplying Acoustical Wall Paneling with square edges made of fibre glass substrate 9

mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction

4.17 MR Class A as per ASTM E-84, fabric as per the selection of the Architect of approved size providing a SQM 40.00 5,004.69 200,187.74

minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel impalers and

construction adhesives as per the instructions laid down by the manufacturer.

Supply and installation of 12mm HD PET panels with density of 2400GSM in approved colour with

customized pattern as per the designers requirement, the panel shall be made from-

-100% polyester fiber, with up to 70% recycled fiber. size of panel 2800mm x 1200mm (± 0.5mm).

Panel Should be mostiure resistant and also Non-toxic, non-irritant, and fire-compliance with safety

standards confirm to Class 1 Fire Ratings tested as per BS 476 Part 6 (Fire Propagation) & Part 7 (Surface

spread of flame) for interior applications. ASTM E84 class A, ASTM D 2859, BS 5852 PART 1.

Noice reduction coefficient (NRC) - 0.45 with direct fix method, can be

achive upto 0.70 with 50 mm gap with pet wool infill and Thermal conductivity ASTM C 518 upto 0.05

The product should be 100% make in india and resistance to fungal growth As Per ASTM C 518.

OEM must have own manufacturing plant along with ISO CERTIFICATIONS- complying to- IGBC

ISO 14184-2 (Release formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system) The cost to

include all required adhesive/ fixing arrangements complete as per instructions of engineer-in-charge.

Supply of VMT Embossed 12mm PET panels which shall be processed with VMT technology for surface

customised colour options with available pattern as per the designers requirement, the panel shall be

-100% polyester fiber, with up to 70% recycled fiber. size of panel 2800mm x 1200mm (± 0.5mm).

Panel Should be mostiure resistant and also Non-toxic, non-irritant, and fire-resistant complying with

safety standards confirm to Class 1 Fire Ratings tested as per BS 476 Part 6 (Fire Propagation) & Part 7

(Surface spread of flame) ASTM E 84 CLASS A, EN 13501 PART 1C,s2,d0 for interior applications.

Noice reduction coefficient (NRC) - 0.3 with direct fix method, 0.85

with 25 mm gap with infill, 0.95 with 50 mm gap with PET WOOL infill.

The product should be 100% make in india and OEM must have ISO CERTIFICATIONS- complying to-

IGBC Membership

ISO 14184-2 (Release formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system). The cost to include all required adhesive/

fixing arrangements complete as per instructions of engineer-in-charge.

particle board or graded wood particle board IS : 3087 marked, with one side decorative and other

4.19 9.18 side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and

fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle

board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one

4.20 9.129 side decorative lamination and other side balancing lamination, including IInd class teak wood lipping SQM 25.00 2,307.35 57,683.75

of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges,

complete as per direction of the Engineer-in-Charge

LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 18mm thick HDHMR Board finished using

1mm thick laminate. The storage shall be complete with all hinges, drawer glides and hardware from

4.21 M.R. approved make. All internal surfaces to be completed using balancing laminate. Including brass D- SQM 95.00 12,003.13 1,140,297.75

type handles for shutters and recessed type handles for drawers. Storage to be of all heights as per

design. Storage shutters to be made in solid laminate/ glass as per design and drawings.

VENEER STORAGE CABINET FOR GENERAL STORAGE- Out of 18mm thick HDHMR Board finished using

4mm thick veneer and polished in melamine to match the veneer cladding item. The venner to be

same as the venner cladding under separate sub- head above complete with all hinges, drawer glides

4.22 M.R. and hardware from Hettich or equivalent. All internal surfaces to be completed using balancing SQM 5.00 15,651.17 78,255.84

laminate. Including brass D-type handles for shutters and recessed type handles for drawers. Storage to

be of all heights as per design. Storage shutters to be made in solid veneer/ glass as per design and

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet Shutters out of 18mm thick

HDHMR board finished in 1mm Laminate. Shutters to be fixed to a frame. Rigidly fixed on both sides and

top finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. Internal

Surface of the shutter in balancing white laminate. All shutters to be provided with Stainless steel louvers

at the top and bottom of the shutter as per the site requirements and instrcution of the Engineer In

SUB TOTAL OF PARTITIONS AND WALL CLADDING 1,835,546.60 25,341,838.76

GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating

of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x

1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the

ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to

the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end

of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200

mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm

long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long.

Including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

600 x 600mm ACOUTIC GRID CEILING - SITC of acoustical grid ceiling with tegular edge and 15 mm

thickness, visible surface of each tile is 7 mm below the grid, visible surface is a batch painted glass

tissue in white, back of the tile covered with glass tissue. Size -600x600x15mm. Acoustics-Sound

absorption Class - Class C at 200 mm o.d.s as per EN ISO 11654, NRC - 0.8 NRC as per ASTM C 423, Fire

Safety - Tested and classified as non combustible according to EN ISO 1182 with reaction to fire

classification class A2 s1 d0 according to EN 13501-1 - European Standard. Flexural tensile strength -

Class C/3N Indoor Air quality - Complying with the French regulation on VOC emissions, A+ level.

Certified by the Finnish Building Information Group (RTS) with the M1 label. Environmental Footprint -

Environmental Product declaration (EPD) acc to international ISO 14025 & EN 15804 series of standards.

Circularity - Minimum post-consumer recycled content 51%, Fully recyclable. Humidity Resistance -Class

C, relative humidity 95% and 30°C, according to EN 13964:2014. Light Reflectance - 80% light

reflectance. Cleanability- Weekly dusting and vacuum cleaning. Accessibilty - The tiles should be easily

demountable, The cost to include all necessary hardwares required for suspending and fixing the

1200 x 300mm ACOUTIC GRID CEILING - SITC of Acoustical microlook tegular edge with 15 mm

thickness ,easily demountable tile , manufactured from High density glass wool, visible surface is

a batch painted glass tissue in white, back of the tile covered with glass tissue. Size- 1200x300x15mm

Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s as per EN ISO 354

Acoustics-Sound absorption Class - Class A at 200 mm o.d.s as per EN ISO 11654

Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110

NRC - 0.9 NRC as per ASTM C 423

Humidity Resistance -Permanent ambient RH up to 95% at 30*C without sagging, warping and

Light Reflectance - 83% light reflectance.

Certified by the Finnish Building Information Group (RTS) with the M1 label. Free from substances of very

high Concern (SVHC) above 100 ppm as defined by the European REACH regulation

(No1907/2006).Product Certified under GRIHA council of India for Green Ratings. Environmental Product

declaration (EPD) acc to international ISO 14025 & EN 15804 series of standards.

Circularity - Re-cycled content of more than 70%

CE marking - CE-marked according to the harmonised standard EN 13964:2014. The cost to include all

necessary hardwares required for suspending and fixing the ceiling.

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Providing and fixing suspended false ceiling of size 900/1200 X 2400 X 12.5mm perforation 3X3mm of

tangent perforation ,8.3MM C/C with 7.1 - 9.8% perforation and NRC upto 0.70: Micro perforation of

glass-fibre reinforced gypsum material, including providing and fixing GI perimeter channels The furring

should be min. 60 mm wide at the short end joints (if wood is used; the steel furring can be min. 45 mm).

The remaining furring can be 45 mm wide. of size 0.55 mm. Thk. having one flange of 20 mm and

another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick

wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI

intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900

mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and

steel expansion fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm

each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in

direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is

then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm centers to G.I. framing in

perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable

attachment. Finally the boards are to be joined and finished so as to have a flush look with jointing

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied

with two coats of primer and Paint to the satisfaction of Architects.

TRAP DOOR :- Providing and fixing trap door in false ceiling made of "pre-laminated board with

5.5 MR hardwood framing, dead locks, lapping all around including all hardware, hinges etc. complete as per SQM 22.00 2,936.78 64,609.06

design and drawing.

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood

framings hung from ceiling @1000mm centre to centre with 2 nos of 6mm thk. Commercial ply on

vertical & 12mm thk. Commercial ply on horizontal surface (straight & curved). Inclusive of finishing in

WOODEN VENEER CEILING :- Providing and fixing wooden veneer ceiling by Fixing Natural Teak Veneer

on 12mm Underlay commercial Ply fixed to a subframe made using 50mm X 50mm Kiln seasoned and

chemically treated hollock wood fixed to RCC ceiilng using Fastners complete as per the instructions of

the Engineer In Charge. (base rate of veneer Rs. 1750/- sqm).

Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the

specifications same as gypsum ceiling.

Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth the

specifications same as gypsum ceiling.

Providing the wooden cove of 150mm x 150mm having a facia of 75mm to match the specifications

5.10 MR same as above. The cove shall be cladded including the cost of cladding 4 mm decorated veneer (BR RMT 20.00 2,676.89 53,537.88

= Rs. 1450/- per sqm) and melamine polish.

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum

ceiling. In order to make the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto

100mm as per drawings. (visible surface of gypsum band to not exceed 100mm) including plastic

emulsion paint.

Providing and fixing of open cell ceiling of approved manufactured from light weight G.I and folded

into u shape profiles. Each panel has a nominal cell wall thickness of 15 mm to give a precise

engineeredceiling appearance. It has a width of 15mm and height 60mm. Maximum length available

is 2 mtr and its thickness 0.45 in G.I. It has equilateral triangles having each side length 175mm. It allows

fire detection and controlsystem, air conditioning and other services to be located within the ceiling

void. all complete as approved & directed by Engineerin-Charge.

Providing of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U

Shape panels in wooden or approved finish. Panels shall be made of 0.5 mm thick galvanized steel

after Powder-coated and length up to 4000 mm. Panel shall be high corrosion resistance and good

color stability. Centre to Centre panel gap will be 100-125 mm. Panels are fixed on to roll formed

carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold

the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss

by 6 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max.

1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are

factory cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side

cap are used to cover the edges of the panels.

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

PET BAFFLES: Providing and fixing of PET acoustic baffles OF SIZE 40*120*2400MM made from standard

9mm PET panels of size 2440mm x 1220mm. The centre to centre spacing can be in multiple of 25mm.

Maximum length of one baffle can be 2440mm and can be increased by joining two or more baffles.

The baffles to be installed with help of specially designed U clamps, 25mm x 25mm x 25mm GI carrier

powder coated in black. Spacing between two carrier to be 1200mm. The carrier should be supported

from true ceiling with help of 4mm threaded rods. The NRC of baffle system to be 0.5

SITC of Baffles of thickness 40 mm with drop height 150.mm at 150mm center to center. Easily

demountable. Manufactured from high density glass wool, with Acoustic painted surface on both the

sides. Edges are straight cut and painted. Acoustics-Sound absorption(Alpha p) - 0.9 at 1000 Hz at 600

mm o.d.s as per EN ISO 354:2003 Humidity Resistance -Permanent ambient RH upto 95% at 30 *

C without sagging , warping or delaminating (EN 13964:2014). Fire Safety-Tested and classified as non

combustible according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN

5.15 MR 13501 -1 -European Standard. Light Reflectance - 85% light reflectance. Indoor Health & Well-being - SQM 120.00 18,341.65 2,200,998.36

Complying with the French regulation on VOC emissions, A+ level. They should also be certified by the

Finnish Building Information Group (RTS) with the M1 label. Free from substances of very high concern

(SVHC) above 100 ppm as defined by the European REACH regulation (No1907/2006). Environmental

Product declaration (EPD) acc to international ISO 14025 & EN 15804 series of standards. Circularity - Re-

cycled content of more than 70% CE marking - CE-marked according to the harmonised standard EN

13964:2014. The cost to include all necessary hardwares required for suspending and fixing the ceiling.

SUB TOTAL OF CEILING 939,569.40 16,491,746.19

6 DOORS/ WINDOWS

35MM THICK LAMINATED FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors finished using 4mm

Thick veneer on both sides panel of size upto 2400mm x 1050mm complete with Hardware including

6.1 MR floor spring, Door Closer, dead Lock with inbuilt key, 800mm D-Handle etc. including cost of teak Nos 5.00 34,989.89 174,949.47

lipping all around. All surfaces to be finished in melamine polish as per approval. The item to include

installation of all kinds of latches as per the requirement.

STILE DOOR - Providing & Fixing of Stile Door System having size of 75*45 with Door Frame formed out of

45* 40mm / 50*50mm of 6063-T6 Virgin grade duly Anodized Aluminium, including 10 mm Toughened

6.2 MR Glass. The cost to include hardware like Door Closure, 4nos Hinges, Lever Handle with mortice lock, Nos 10.00 67,286.87 672,868.73

Door Seal & Gaskets etc. in approved shade and design as per architectural drawings and instructions

of the architect. The size of door shall be upto 1050mm X 2400mm.

Double Glazed Single Swing Door Size: 900 x 2400mm - Providing & Fixing of double Glazed Stile Door

having size of 75x55mm with door profile 6063-T6 Virgin grade duly Anodized Aluminium Door Sections

6.3 MR having sizes of 75x30x1.5mm thick, 2 Layers of 6 mm toughened Glass including Door Closer TS 2000, Nos 40.00 114,587.57 4,583,502.96

4nos Flush Hinges, SS Offset D type Pull Handle 25 x 450mm with narrow Stile mortise Dead lock &

Gaskets. complete in all respects as per instruction of engineer-in-charge.

STILE DOOR - Providing & Fixing of Stile Door System having size of 75*45 with Door Frame formed out of

45* 40mm / 50*50mm of 6063-T6 Virgin grade duly Anodized Aluminium, including 10 mm Toughened

6.4 MR Glass. The cost to include hardware like Door Closure, 4nos Hinges, Lever Handle with mortice lock, Nos 3.00 87,901.51 263,704.52

Door Seal & Gaskets etc. in approved shade and design as per architectural drawings and instructions

of the architect. The size of door shall be upto 1200mm X 2400mm.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

6.5 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast

lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood CUM 0.90 142,949.70 128,654.73

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,

6.6 9.53 nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 EACH 60.00 228.85 13,731.00

coarse sand : 6 graded stone aggregate 20mm nominal size).

LAMINATED FLUSH DOOR- Flush Doors finished using 1mm Thick Laminate on both sides panel of size

upto 2400mm x 1000mm complete with Hardware including hinges, Door Closer, Mortice Lock with

Handle, latches etc. including cost of Door frame with melamine/ duco finish. The cost to include

providing and fixing of vision panel as per design.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc.

FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 1050x2400. with vision panel

using FR glass complete with Fire proof door frame. One side to be finished in fire retardant paint and

one side to be finished in Laminate of approved shade. All Frame to be finished in fire retardant paint.

All hinges and hardware to be thermatically sealed and 120 mins fire rated. Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring

type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete

as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

SUB TOTAL OF DOORS 169,279.29 6,011,560.31

7 FINISHES & MISCELLANEOUS

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per

manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer

applied @ 0.75 ltr /10 sqm

PAINT ON DUCTS & METAL SURFACES: Providing and applying Satin Spray Paint to AC Duct external

metal Surfaces, including paint putty, base coat as pre manufacturers recommendations and finishing

with 2/3 coats of paint of approved color and make. Surface coating to be achieved as per

manufacturer’s recommendations for coverage of paint.

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 15.00 172.60 2,589.00

7.4 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

13.61.1 Two or more coats on new work SQM 30.00 155.90 4,677.00

Providing & fixing decorative Poly décor fabric Wall Paper (on walls and ceiling) of weight 475 g

7.5 MR /sqm as per approved shade & design including prepration of surface with 2 coats of Nubin Glue SQM 80.00 4,518.28 361,462.07

based epoxy quote.

ZEBRA BLINDS - Providing and fixing of Blinds in band width 7.5 cm - 12 cm and made up of 100%

polyster, in width of 250 - 280 cm, weight - 160g/sqm - 190g/sqm, thickness - 0.50 mm - 0.70mm ( opaue

part ), Colorfastness to light - above 4 grade. Blind tube made of aluminium with a diameter of 36mm,

botom rail made of aluminum with powder coated having weight 390 gm/meter fitted with end caps

in colour matching to the fabric and mechanism of plastic with chain and metal bracket. The blind

shall have aluminum cover with the matching fabric designed on it. Aluminium profile should have

temper WP consisting of alloy 63400 along with anodizing of 10 micron and powder coating of 60

micron. The tensile strength of profile should be 9.10 Kg/mm square and elongation 18.The control

clutch drive unit engineered heavy duty chain drive pulley operating system consisting of gear clutch

7.6 M.R. housing and locking plug containing minimum 6 ribs and inserted at minimum of 38mm into roller tube. SQM 675.00 5,875.59 3,966,020.48

Self-lubricating exclusive clutch with safety pins for secure bracket installation and unlocking pin for

quick manual removal. It shall be driven by a ball chain pulley with ball chain and can be positioned

at Right hand or Left hand side of the shade. Clutch gear ratio of 1.75:1 for reduced operating force on

larger blinds. Mounting hardware brackets universal brackets including end plug bracket with lock

down retainer device. Brackets finish of powder coated metal installation brackets made of stamped

and hardened steel. Roller tube circular-shaped aluminium tube extruded from alloy 63400 and temper

WP. Bottom rail flat-shaped extruded aluminium from alloy 63400 and temper WP. Ball chain shall be

2mm diameter cord with plastic balls moulded to form an endless ball chain used for raising or lowering

action of the shades. All plastic components must be UV-stable - white in colour.

Digitally signed by AMIT

S.No. (CIVIL) REF. DESCRIPTION UNIT QTY DSR DSR AMOUNT MARKET RATE MR AMOUNT

Providing and fixing of window blinds as per approved sample consisting of cell in cell , dual cell and

single cell honeycomb shades with easy rise operating system and standard design option original non -

woven honeycomb shades having soft fabric appearance and high energy -efficient fabric with high

tear strength constructed out of anti static , anti-UV, damp proof , resilient, colour fast & sanitized treat

100% spun bonded non -woven polyester fibre & precision manufacture to form a hexagonally shaped

cell . Cell size 3Ú4”Honeycomb structure with dis nct air pocket for energy efficiency and increased

insulation. Shadings are single tone facing both exterior and interior . Being a Low shading co -efficient

will have following Comfort rating & solar optical properties . Aluminium profile should have temper WP

consisting of alloy 63400 along with anodizing of 10 micron and powder coating of 60 micron. The

tensile strength of profile should be 9.10 Kg/mm square and elongation 18.The control clutch drive unit

engineered heavy duty chain drive pulley operating system consisting of gear clutch housing and

locking plug containing minimum 6 ribs and inserted at minimum of 38mm into roller tube . It is

selflubricating exclusive clutch with safety pins for secure bracket installation and unlocking pin for

quick manual removal . Universal clutch is most convenient for large windows down to the smallest

windows. It shall be driven by a ball chain pulley with ball chain and can be positioned at right hand or

left hand side of the shade . Clutch gear ratio of 1.75:1 for reduced Quotation operating force on larger

blinds. Mounting hardware brackets universal brackets including end plug bracket with lock down

retainer device . Brackets finish of powder coated metal installation brackets made of stamped and

hardened steel. Roller tube circular-shaped aluminium tube extruded from alloy 63400 and temper WP .

Bottom rail flat -shaped extruded aluminium from alloy 63400 and temper WP . Ball chain shall be 2mm

diameter cord with plastic balls moulded to form an endless ball chain . It is used for raising or lowering

action of the shades. Plastic parts all plastic components are UV-stable compounds available white.

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface with 15 yrs MCS

warranty as approval of the Architect. (Only film surface area shall be measured and paid).

Preparation of complete set of civil and interior finishing drawings including details. A qualified

professional for the purpose shall be appointed after due appproval from Engineer In Charge.

Providing and fixing of 4,6 mm thick annealed GRIHA rated lacquered glass manufactured industrially

by curtain coating process with PU lacquer (50 micron thick), opaque (if viewed against a support wall)

conforming to EN 16477 standards for back painted glass , of approved color by Architect/ Client fixed

with compatible Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack

free time of 10 to 30 mins compatible for installation of mirror and lacquered glass / Foam based

double sided adhesive tape for instantaneous adhesion, compatible with mirror and lacquered glass

having Shear bond strength (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water

proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other

structure. The contractor should submit test reports for backpainted glass from manufacturer - High

humidity Resistance (conforms to BS EN 1036 1999); Color fastness ISO 105B02 standard & Mechanical

Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross Hatch Test ) standard The manufactured

backpainted glass should be environmentally friendly (no lead, no arsenic, no copper,

noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive

strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass

Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and colour using approved

Adhesive to 12 mm thk. Waterproof Plywood of approved brand as per shape, pattern & details given

7.11 M.R. in the drawing. The rate includes providing & fixing beading, cutting, scaffolding, nails, all materials, SQM 52.00 15,955.16 829,668.41

labour, lead, lifts, HOM etc., complete.-for Lift Cladding. (The make, Shade, pattern etc., to be

approved by EIC).

SUB TOTAL OF FINISHES 656,742.10 9,875,366.96

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

1 CHAIRMAN'S TABLE Main Table Dimension:(L)2800mm X (D)1130mm X (H)770mm

Side Runner Dimension: :(L)1200mm X (D)600mm X (H)770mm

Supplying, and placing in position of table. Made of engineered wood-HDHMR board & veneer glossy finish on the

same. Main Table top thkness 80mm , side panel/gable end in 70mm thk HDHMR with veneer glossy finish. Main table

and side runner having a skirting @120mm thk with gives a rich look. The office desk comes with the side runner having

enough storage space.The side runner top with a thickness of 80mm thk that gives the great look . Side table, side

panel, shelves,drawers made up of 18mm thk HDHMR with veneer finish. Table having a provision of Pedestal of size:

400(L) X 500(D) X 660(H) having three drawers to store essential & undestructure made out of 18mm thk HDHMR with

veneer finish .Drawers have the stylish handle which enhance the look. Side storage unit having a side panel, one

drawer , one shutter & one shelf of 18mm thk HDHMR with veneer finish. The product should be from

manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/ AIOTA Certification.The product should

be as per above given specification subject to approval of EIC

Supply and placing of main chair. Total height 1210 to 1280mm. High back Chair having back height of 770 +/-5mm

and width of 380 +/-5mm from top & 500 from mid (lumbar) level. Seat Depth shall be 480 +/-5mm and seat width shall

be 540 +/-5mm at front & 450 +/-5mm at back. Armrest to Armrest distance of 680 +/-5mm. Seat height shall range

between 410 mm to 470 mm. Armest shall be finished with foam & leather on the user side & top with water fall edge

to provide comfort to user & outside of armrests as well as below back shall be finished with wooden texture. Below

portion of armrest opening towards seat shall be finished with crome surface. Knee tilt mechanism shall be provided

having tilt tension adjustment & height adjustment at same level on right hand side of user & any position locking level

2 CHAIRMAN'S MAIN CHAIR NOS 1.00 123,173.19 123,173.19

at the left hand side of user. Padded lumber support to be provided of height minimum 200 mm. Back of the chair shall

be finished with leather upto height of 600 mm & wooden texture finish upto 200 mm & leather below the wooden

texture. Aluminium die cast pedestal having length of prongs 310 mm with 50 mm height towards centre & 25 mm

height outside. High Quality leather in beige or black to be suppiled. Twin wheel castors to be provided.Tolerance of +/-

5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe

thickness & Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification,

AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of chair. Total heigt 1050 to 1120mm. Mid back Chair having back height of 610 +/-5mm and width

of 380 +/-5mm from top & 500 +/-5from mid (lumbar) level. Seat Depth shall be 480 +/-5mm and seat width shall be 540

+/-5mm at front & 450 +/-5mm at back. Armrest to Armrest distance of 680 +/-5mm. Seat height shall range between

410 +/-5mm to 470 +/-5mm. Armest shall be finished with foam & leather on the user side & top with water fall edge to

provide comfort to user & outside of armrests as well as below back shall be finished with wooden texture. Below

portion of armrest opening towards seat shall be finished with crome surface. Knee tilt mechanism shall be provided

having tilt tension adjustment & height adjustment at same level on right hand side of user & any position locking level

3 CHAIRMAN'S VISITOR CHAIR NOS 4.00 119,496.38 477,985.51

at the left hand side of user. Padded lumber support to be provided of height min. 200 mm. Back of the chair shall be

finished with leather upto height of 440 mm & wooden texture finish upto 200 mm & leather below the wooden texture.

Aluminium die cast pedestal having length of prongs 310 mm with 50 mm height towards centre & 25 mm height

outside. High Quality leather in beige or black to be suppiled. Twin wheel castors to be provided. Tolerance of +/- 5mm

to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness &

Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and

anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided

with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat &

back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish

with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam,

100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm

thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden

4 SOFA Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood

polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper

support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 -

180mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and

shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as

directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and

with 05 years warranty.

4.1 3 seater sofa overall dimension - 1950mm W x 760-780mm D x 680-700mm H NOS 1.00 93,985.85 93,985.85

4.2 2 seater sofa overall dimension - 1550mm W x 760-780mm D x 680-700mm H NOS 1.00 69,432.85 69,432.85

4.3 1 seater sofa overall dimension - 810mm W x 760-780mm D x 680-700mm H NOS 1.00 40,564.89 40,564.89

Providing and fixing tables of Centre table Size - 900mm W x 600mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

5 CENTER TABLE 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 1.00 16,735.41 16,735.41

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

Providing and fixing tables of Side table Size - 500mm W x 500mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

6 SIDE TABLE 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 3.00 14,706.93 44,120.80

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

7 RECLINER Recliner sofa for ante room

Dimension (W)870mm X (D)970mm X (H)1000mm

Supplying, and placing in position of recliner sofa with manual recline mechanism, completely from a sitting position to

a sleeping position. The seat cushion to be made of multi layered foam of density 40kg/m3. The seating cushion to

have 2.75 & 1.75 inches of elastic webbing. The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 NOS 1.00 83,606.96 83,606.96

gsm. The product should be from manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/

AIOTA Certification.The product should be as per above given specification subject to approval of EIC

Supplying and placing in position of wardrobe. The Top, side panel, shutter, bottom , drawer facia & shelves made out

of 18mm thk laminated mdf board with pvc edge banding . All the exposed edges are edge banded with 2mm thk

pvc edging. Wardrobe back & drawer bottom are made of 8mm thk laminated mdf board with 2mm thk pvc edge

8 WARDROBE banding. Having a Provision of openable shutter with D shape handles and locking arrangement . Also having a NOS 1.00 51,236.39 51,236.39

provision of drawer, shelves & hanging rod . The product should be from manufacturer(OEM) which have BIFMA

Certification /GREEN PRO Certification/ AIOTA Certification.The product should be as per above given specification

subject to approval of EIC. Dimension: 900mm(L) x 600mm(D) x 1800mm(h)

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of Chamber member Room Table & Side Table

Overall Size : W 2300 x D 1000 x H 750mm & Side Unit Extention: W 1400 x D 550 x H 750mm. Table Top: 25mm thick pre

laminated particle board with 2mm PVC edge lipping supported on V Shape aluminium die cast connectors of min

size 430 mm L x 110 mm H x 25 mm Thick. 4 Connectors on Main table & 2 on side unit shall be provided. All sides of the

worktop except corners of main & side table shall be provided with 2mm thick alumimum extrusion of 40mm + 25 mm +

30 MM + 8 mm formed into horizontal & vertical direction to enable support as well as top surface coverage. edge

surface extrusion supporting the worktop to be tappered towards top. Support: End Legs: 50mm thick pre laminated

particle board with 2mm PVC edge lipping & 3 equal drawer pedestal size of 600 x 850 x 570mm (LDH). Modesty

Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 65mm dia wire manager

CEO & MEMBER'S CHAMBER - grommet on table, flip up and provision to place CPU in side extension drawer. Sufficient storage space to be

TABLE priovided in the storage pedestal of the table having drawers at the main table & hinged door storage below the side

unit. The main and the return table top will have 10 mm thick Euro bronze glass with white vinyl film hot laminated and

Kuraray pvb interlayer. Back Unit Overall Size W 1500 x D 600 x H 750mm, Table Top: 25mm thick pre laminated particle

board with 2mm PVC edge lipping sides covered with 2mm thick anodised alumimum extrusion of same size as above

supported on V Shape aluminium die cast connectors of same size as above. Back: 25mm thick pre laminated particle

board with 2mm PVC edge lipping with aluminium die cast arms Shutters: 25mm thick pre laminated particle board

with 2mm PVC edge lipping with brush steel handles and softclose drawer slides and hinges. The back unit table top

shall also have 10 mm thick Euro bronze glass with white vinyl film hot laminated and Kuraray pvb interlayer. The OEM

shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification, India Design Mark.

Supply and placing of High Back Chair (Leatherite)

High back Chair having overall height 1200-1300mm, back height of 790 mm from seat level and width of 460 mm from

top & 520 from mid (lumbar) level. Seat Depth shall be 490 mm and adjustable upto 530mm. seat width shall be 520

mm measured at centre of the seat. Seat height shall range between 430 mm to 520 mm. Armest shall be finished with

foam & leatherite on the top & the structure of the armrest shall a die cast aluminium with buffed finish & fixed with the

seat below. The length of the top of the arm shall be 250 mm & width of 60 mm. Seat should be made up of foam pre

CEO & MEMBER'S CHAMBER moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat, back & headrest

MAIN CHAIR shall be upholstered with Leatherette 75% PVC & 25% polyester – 640 GSM, Abrasion-100000 cycles over PU faom. The

synchro mechanism shall be provided having 3 position multilocking & seat adjustable on the left hand side and height

adjustment on the right hand side of the user.The mechanism shall allow 360 degree revolving feature along with

height adjustablility. Aluminium die cast pedestal having length 5 twin 60 mm wheel castors heavy duty shall be

provided. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. tolerance of 25mm for seat & back size

to be considered. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA,

IGBC Gold rated factory certification, India Design Mark.

Supply and placing of Medium Back Chair (Leatherite)

Medium back Chair having overall height 1050-1150mm, back height of 590 mm from seat level and width of 460 mm

from top & 520 from mid (lumbar) level. Seat Depth shall be 490 mm and adjustable upto 530mm. seat width shall be

520 mm measured at centre of the seat. Seat height shall range between 430 mm to 520 mm. Armest shall be finished

with foam & leatherite on the top & the structure of the armrest shall a die cast aluminium with buffed finish & fixed

with the seat below. The length of the top of the arm shall be 250 mm & width of 60 mm. Seat should be made up of

CEO & MEMBER'S CHAMBER - foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat and back

VISITOR CHAIR shall be upholstered with Leatherette 75% PVC & 25% polyester – 640 GSM, Abrasion-100000 cycles over PU faom. The

synchro mechanism shall be provided having 3 position multilocking & seat adjustable on the left hand side and height

adjustment on the right hand side of the user.The mechanism shall allow 360 degree revolving feature along with

height adjustablility. Aluminium die cast pedestal having length 5 twin 60 mm wheel castors heavy duty shall be

provided. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. tolerance of 25mm for seat & back size

to be considered. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA,

IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and

anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided

with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat &

back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish

with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam,

100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm

thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden

12 SOFA Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood

polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper

support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 -

180mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and

shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as

directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and

with 05 years warranty.

12.1 3 seater sofa overall dimension - 1950mm W x 760-780mm D x 680-700mm H NOS 3.00 93,985.85 281,957.54

12.2 2 seater sofa overall dimension - 1550mm W x 760-780mm D x 680-700mm H NOS 1.00 69,432.85 69,432.85

12.3 1 seater sofa overall dimension - 810mm W x 760-780mm D x 680-700mm H NOS 2.00 40,564.89 81,129.78

Providing and fixing tables of Centre table Size - 900mm W x 600mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

13 CENTER TABLE 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 3.00 16,735.41 50,206.24

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

Providing and fixing tables of Side table Size - 500mm W x 500mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

14 SIDE TABLE 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 4.00 14,706.93 58,827.74

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

15 RECLINER Recliner sofa for ante room

Dimension (W)870mm X (D)970mm X (H)1000mm

Supplying, and placing in position of recliner sofa as perphotograph (only for reference). with manual recline

mechanism, completely from a sitting position to a sleeping position. The seat cushion to be made of multi layered

foam of density 40kg/m3. The seating cushion to have 2.75 & 1.75 inches of elastic webbing. The backrest has a foam

of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The product should be from manufacturer(OEM) which have

BIFMA Certification /GREEN PRO Certification/ AIOTA Certification.The product should be as per above given

specification subject to approval of EIC

Supplying and placing in position of wardrobe as perphotograph (only for reference)/drawing. . The Top, side panel,

shutter, bottom , drawer facia & shelves made out of 18mm thk laminated mdf board with pvc edge banding . All

the exposed edges are edge banded with 2mm thk pvc edging. Wardrobe back & drawer bottom are made of 8mm

16 WARDROBE thk laminated mdf board with 2mm thk pvc edge banding. Having a Provision of openable shutter with D shape NOS 1.00 51,236.39 51,236.39

handles and locking arrangement . Also having a provision of drawer, shelves & hanging rod . The product should be

from manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/ AIOTA Certification.The product

should be as per above given specification subject to approval of EIC. Dimension: 900mm(L) x 600mm(D) x 1800mm(h)

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of table of overall size of table shall be 2400L x 1850D x 750H.The main table top shall be size of

2000L x 900D. The table shall be made of E1 grade particle board with melamine finish. Table shall have corner golden

aluminium parts. Table modesty panel shall have aluminum and hard PU decorations.The table top shall have 50mm

thick. table side unit shall have size of 1800L x 600D x 600H. Side unit shall have Fixed side return can be left or right

when first assembly, including swing door, drawers and open space for CPU. Wire Management: 1 No. Aluminium Flip

Up and provision to mount swicthes and sockets on metal cable Dump and vertebra considered for wire uptake from

17 DY. REGISTRAR & REGISTRAR NOS 2.00 345,521.02 691,042.03

floor to cable dump.

The overall size of back unitshall be of 2400W x 400D x 1950H. The back unit shall be made of E1 grade particle board

with melamine finish. The back unit shall have golden extruction in both side. The storage comes with openable door

and open shelves for storage and display. The storage shall have multiply shelf. 50mm skirting shall be present at the

bottom. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Supply and placing of chair of overall size of High back shall be : Back width : 480mm , Total height : 1150 to 1250 mm,

Back height- 755 mm. Seat width : 490 mm, Seat depth : 480 mm, Seat height : 455 to 555 mm. Arms & back: It shall bea

molded shell with MS frame and upholstered with leatherette. Leatherette upholstery: Shell shall be upholstered with

75% PVC & 25% polyester – 640 GSM, Abrasion- 100000 cycles. Foam: Cushion with pre moulded foam of 65 kg/m3

density in the shape of the mold. Hardness – 22 ± 3 kgf. Seat: upholstery : Seat shall beupholstered with leatherette.

Leatherette upholstery: Shell shall be upholstered with 75% PVC & 25% polyester – 640 GSM, Abrasion- 100000 cycles

Foam: Cushion with pre moulded foam of 65 kg/m3 density in the shape of plywood. Hardness – 18 ± 3 kgf. Ply wood:

12 mm thick with 9 ply. It shall behot pressed ply - conforming to shall be303. The plywood shall befitted with metal “T”

nut to have metal to metal contact for the hardware used for fixing the mechanism. Thshall betechnology ensures long

and efficient and safe functioning of the chair without any shake and play in the long run. The seat profile shall

18 DY. REGISTRAR & REGISTRAR bedesigned with water fall to provide necessary comfort in popliteal region.Mechanism: Synchro tilt Mechanism – NBA NOS 2.00 51,236.37 102,472.74

005 mechanism offered in Multi lock features. Thshall be mechanism shall be manufactured out of cold Rolled Carbon

Steel shall be 513-1994 Sheets, the steel components are manufactured with highly precision tools for accuracy in

matching other parts for smooth functioning. The taper angle should match with the taper angle of gas lift swaging--

1°26’16”.Gas lift: : Single swage Class 4 tested -ANSI BIFMA performance standards. The pneumatic height adjustment

has an adjustment stroke of 95 -100 mm as per the seat height criteria and 360° revolving.Base: The 660mm PCD (26

inches) five pronged base shall be made out of Aluminium. The base Outer diameter shall be 750 mm with

casters.Casters : Twin Casters 60mm dia with Nylon material complying to ANSI / BIFMA X 5.1 – 2017 standards. The axle

pin shall be rust protected- Zinc passivated. The pin shall be designed to have push fit with lock ring. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification, India Design Mark.

Supply and placing of chair of overall size of Dimensions: Medium back : Back width : 490mm , Total height : 935 to 1035

mm, Back height- 550 mm. Seat width : 490 mm, Seat depth : 480 mm, Seat height : 455 to 555 mm. Arms & back: It

shall be molded shell with MS frame and upholstered with leatherette. Leatherette upholstery: Shell shall be

upholstered with 75% PVC & 25% polyester – 640 GSM, Abrasion- 100000 cycles. Foam: Cushion with pre moulded foam

of 65 kg/m3 density in the shape of the mold. Hardness – 22 ± 3 kgf. Seat: upholstery : Seat shall beupholstered with

leatherette. Leatherette upholstery: Shell shall be upholstered with 75% PVC & 25% polyester – 640 GSM, Abrasion-

100000 cycles Foam: Cushion with pre moulded foam of 65 kg/m3 density in the shape of plywood. Hardness – 18 ± 3

kgf. Ply wood: 12 mm thick with 9 ply. It shall behot pressed ply - conforming to shall be303. The plywood shall befitted

with metal “T” nut to have metal to metal contact for the hardware used for fixing the mechanism. Thshall

betechnology ensures long and efficient and safe functioning of the chair without any shake and play in the long run.

19 DY. REGISTRAR & REGISTRAR The seat profile shall bedesigned with water fall to provide necessary comfort in popliteal region. Mechanism: Synchro NOS 6.00 44,379.12 266,274.70

tilt Mechanism – NBA 005 mechanism offered in Multi lock features. Thshall be mechanism shall be manufactured out

of cold Rolled Carbon Steel shall be 513-1994 Sheets, the steel components are manufactured with highly precision

tools for accuracy in matching other parts for smooth functioning. The taper angle should match with the taper angle

of gas lift swaging-- 1°26’16”.Gas lift: : Single swage Class 4 tested -ANSI BIFMA performance standards. The pneumatic

height adjustment has an adjustment stroke of 95 -100 mm as per the seat height criteria and 360° revolving. Base: The

660mm PCD (26 inches) five pronged base shall be made out of Aluminium. The base Outer diameter shall be 750 mm

with casters.Casters : Twin Casters 60mm dia with Nylon material complying to ANSI / BIFMA X 5.1 – 2017 standards. The

axle pin shall be rust protected- Zinc passivated. The pin shall be designed to have push fit with lock ring. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of 2-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 1545L x 880D x 840H. The seat/back mounting frame assy. holds the two

side frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure

shall be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should

be used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall

be used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and

20 back are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best NOS 1.00 64,858.96 64,858.96

seating comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be

elevated from ground by about 3 inches using metal powder coated legs, which shall create provision for easy

cleaning at the same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more

than 50K rubs, colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best

feel & comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of 1-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 900L x 880D x 840H. The seat/back mounting frame assy. holds the two side

frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure shall

be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should be

used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall be

used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and back

21 are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best seating NOS 1.00 54,576.35 54,576.35

comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be elevated

from ground by about 3 inches using metal powder coated legs, which shall create provision for easy cleaning at the

same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more than 50K rubs,

colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best feel &

comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Supply and placing of Centre table Size

The overall size of the Centre table shall be 1050 mm Length x 550 mm depth, 450 mm height. the table top shall be

made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion surface shall be

provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC. Under

22 Structure Support: Table top shall be supported on CRCA legs duly powder coated. The Chair understructure should be NOS 1.00 14,538.11 14,538.11

provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom. The edges of the table top

shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker on the top & thinner on the

bottom side. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of corner table. The overall size of the corner table shall be dia 600mm, 450 mm height. the table

top shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion

surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any

VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The table

understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom.

The edges of the table top shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker

on the top & thinner on the bottom side.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of overall size of chair shall be total width 620mm, total depth 600mm and total height

800mm.Back width at bottom shall be 520mm, Back height from seat shall be 390 mm. Seat width 440 mm, Seat depth

450 mm and Seat height 445 mm. The Frame shall be made out of rectangular tube 40X20X2mm & circular tube 32 mm

swaged to 19 mm & 1.6 mm thickness. Frame shall welded by CO2 welding process for uniform finsh. Frame leg shall

be fitted with Molded LDPE bushes. It shall have molded shell upholstered with fabric. Fire rated of fabric confirming to

BS EN 1021(match), IS 15061-2002 is optional. seat shall be provided with top cushion for good comfort. Cushion with

pre moulded foam of 50 kg/m3 density & Hardness 29 to 31 kgf at 50% deflection. Powder coat shall be done with

black color to provide an attractive finshall h. The powder coating pre-treatment shall be carried out with three in one

chemical. After pre-treatment process, the components are powder coated for better adhesion of paint. The frames

shall powder coated with epoxy polyester powder to the thickness of 40-60 microns as per shall 101 and oven baked

at 180°. Product undergoes the following testing process for durability and functionality, cross cut test for ensuring

adhesion of powder coating as per shall 13871. Powder coated products shall be durable & reduce the rshall k of

scratches, chipping, abrasions, corrosion, fading and other wear shall sues.The OEM shall have ISO 9001, ISO 14001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of Cabin Table in size of 1800W X 900D X 750H, Side unit of 1050W X 450D X 750H Table Top: 25mm

thick Pre laminate particle board E1 norms with 2mm PVC edge lipping on all exposed edges. Two Long sides of the

work surface shall be provided with reverse tapered edge design created by chamfering the board at 45 degree

inside for 17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic

machine. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number “7” shape &

oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm table height, it acts

as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube &

connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast 90deg – 02 way

connectors. The connector should have “V” / “U” shape tapered groove for sliding a Aluminium diecast slider nut. The

slider nut shall be an Aluminium diecast part that has same taper as of “V” / “U” shape in the diecast connector.

Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 450mm

Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover.

Cross Beam: Leg to Leg shall be connected using cross beams made from 50x25x1.60mm (16g) Rectangular tube and

to give floating look & to connect the table top with cross beams injection moulded polycarbonate spacers should be

COUNSEL & ASST. REGISTRAR -

25 used of dia 61mm x 42.50mm H insert moulded with M6x1P zinc blue plated bolt of 22mm L.Spacer height including 4.00 131,736.48 526,945.93

bolt should be 64.50mm. Side Composite Storage (Openable Shutter +3D+1F) Top & Sides : 18mm Thk pre laminated

particle board Back E1 norms: 9mm Thk pre laminated particle board Shutters : 18mm Thk pre laminated particle board

Handle. Handless Finger groove shall be created on top edge of shutter doors by providing a reverse tapered profile

edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. Suitable number lock shall be provided.

The overall size of Back storage shall be 1500 x 450 x 750 (WDH) mm. Top shall be made up of 18mm thick pre

laminated particle board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm

PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. Shutters to be provied for

compartment. The storage shall have adjustable shelf. Edge: All exposed shall be sealed with 2mm thick PVC edge

lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered

towards inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Cam Lock

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2,

Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of chair. The overall size of Chair shall be : width 600 +/-5mm, depth 640 +/-5mm. Total height 1170

to 1270 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm

and Seat height 470mm to 570 mm +/-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density. hardness

of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be made up of foam pre moulded at 55 kg/m3 density.

hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster

180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be

supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey shade,

armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar Support

made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar Support

COUNSEL & ASST. REGISTRAR - material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock Mechanism

MAIN CHAIR (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The mechanism shall

allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied

with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm to 260mm

adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4

tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 980 to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar

Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock

COUNSEL & ASST. REGISTRAR -

27 Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The 8.00 23,678.67 189,429.33

mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height)

to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm

to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Supply and placing of overall size of chair shall be total width 620mm, total depth 600mm and total height

800mm.Back width at bottom shall be 520mm, Back height from seat shall be 390 mm. Seat width 440 mm, Seat depth

450 mm and Seat height 445 mm. The Frame shall be made out of rectangular tube 40X20X2mm & circular tube 32 mm

swaged to 19 mm & 1.6 mm thickness. Frame shall welded by CO2 welding process for uniform finsh. Frame leg shall

be fitted with Molded LDPE bushes. It shall have molded shell upholstered with fabric. Fire rated of fabric confirming to

BS EN 1021(match), IS 15061-2002 is optional. seat shall be provided with top cushion for good comfort. Cushion with

COUNSEL & ASST. REGISTRAR - pre moulded foam of 50 kg/m3 density & Hardness 29 to 31 kgf at 50% deflection. Powder coat shall be done with

SOFA CHAIR black color to provide an attractive finshall h. The powder coating pre-treatment shall be carried out with three in one

chemical. After pre-treatment process, the components are powder coated for better adhesion of paint. The frames

shall powder coated with epoxy polyester powder to the thickness of 40-60 microns as per shall 101 and oven baked

at 180°. Product undergoes the following testing process for durability and functionality, cross cut test for ensuring

adhesion of powder coating as per shall 13871. Powder coated products shall be durable & reduce the rshall k of

scratches, chipping, abrasions, corrosion, fading and other wear shall sues.The OEM shall have ISO 9001, ISO 14001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of Cabin Table in size of 1500W X 750D X 750H, Side unit of 1050W X 450D X 750H Table Top: 25mm

thick Pre laminate particle board E1 norms with 2mm PVC edge lipping on all exposed edges. Two Long sides of the

work surface shall be provided with reverse tapered edge design created by chamfering the board at 45 degree

inside for 17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic

machine. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number “7” shape &

oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm table height, it acts

as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube &

connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast 90deg – 02 way

connectors. The connector should have “V” / “U” shape tapered groove for sliding a Aluminium diecast slider nut. The

slider nut shall be an Aluminium diecast part that has same taper as of “V” / “U” shape in the diecast connector.

Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 450mm

Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover.

Cross Beam: Leg to Leg shall be connected using cross beams made from 50x25x1.60mm (16g) Rectangular tube and

to give floating look & to connect the table top with cross beams injection moulded polycarbonate spacers should be

29 PA/ PS - TABLE used of dia 61mm x 42.50mm H insert moulded with M6x1P zinc blue plated bolt of 22mm L.Spacer height including NOS 3.00 126,850.00 380,550.00

bolt should be 64.50mm. Side Composite Storage (Openable Shutter +3D+1F) Top & Sides : 18mm Thk pre laminated

particle board Back E1 norms: 9mm Thk pre laminated particle board Shutters : 18mm Thk pre laminated particle board

Handle. Handless Finger groove shall be created on top edge of shutter doors by providing a reverse tapered profile

edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. Suitable number lock shall be provided.

The overall size of Back storage shall be 1500 x 450 x 750 (WDH) mm. Top shall be made up of 18mm thick pre

laminated particle board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm

PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. Shutters to be provied for

compartment. The storage shall have adjustable shelf. Edge: All exposed shall be sealed with 2mm thick PVC edge

lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered

towards inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Cam Lock

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2,

Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of chair, The overall size of Chair shall be : width 600 +/-5mm, depth 640 +/-5mm. Total height 1170

to 1270 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm

and Seat height 470mm to 570 mm +/-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density. hardness

of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be made up of foam pre moulded at 55 kg/m3 density.

hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster

180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be

supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey shade,

armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar Support

made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar Support

material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock Mechanism

(Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The mechanism shall

allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied

with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm to 260mm

adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4

tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 980 to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar

Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock

31 PA/ PS - VISITOR CHAIR Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The NOS 6.00 23,678.67 142,072.00

mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height)

to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm

to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Supply and placing of cafe table. The overall size of the café table is 1050 dia. The top shall be made up of 18mm

Hydroshield material to enable use of table in cafeteria and water reistant. Leg: shall be made up of high pressure

aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at

32 BREAKOUT AREA - TABLE bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural support member, NOS 2.00 49,636.96 99,273.91

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical

legs through a high pressure Aluminium diecast connectors. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2,

Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of chair. overall size of chair shall be total width 620mm, total depth 600mm and total height

800mm.Back width at bottom shall be 520mm, Back height from seat shall be 390 mm. Seat width 440 mm, Seat depth

450 mm and Seat height 445 mm. The Frame shall be made out of rectangular tube 40X20X2mm & circular tube 32 mm

swaged to 19 mm & 1.6 mm thickness. Frame shall welded by CO2 welding process for uniform finsh. Frame leg shall

be fitted with Molded LDPE bushes. It shall have molded shell upholstered with fabric. Fire rated of fabric confirming to

BS EN 1021(match), IS 15061-2002 is optional. seat shall be provided with top cushion for good comfort. Cushion with

pre moulded foam of 50 kg/m3 density & Hardness 29 to 31 kgf at 50% deflection. Powder coat shall be done with

33 BREAKOUT AREA - CHAIR NOS 6.00 30,899.92 185,399.55

black color to provide an attractive finshall h. The powder coating pre-treatment shall be carried out with three in one

chemical. After pre-treatment process, the components are powder coated for better adhesion of paint. The frames

shall powder coated with epoxy polyester powder to the thickness of 40-60 microns as per shall 101 and oven baked

at 180°. Product undergoes the following testing process for durability and functionality, cross cut test for ensuring

adhesion of powder coating as per shall 13871. Powder coated products shall be durable & reduce the rshall k of

scratches, chipping, abrasions, corrosion, fading and other wear shall sues.The OEM shall have ISO 9001, ISO 14001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of workstation. The overall size of workstation shall be 1500L1 x 1500L2 x 600D x 750H. The partition

shall be provided at main and return side. Workstations of overall panel thickness 65 mm (+/-5mm) and height of

1200mm (+/- 5mm). The worktop shall be made up of 25mm E1 norm PLPB with matching PVC edge band 2mm thick.

The worktop shall be provided with 65mm gromet cut & shall be supported on CRCA bracket with one side fixed on

rectangular slot of frame vertical and other side to worksurface. The partition frame shall be made up of nonferrous

6063 grade alum alloy confirming to DIN ISO-2768-1 & fabricated through weldless technology & fitted with pre

moulded M8 levellers zinc passivated for height adjustment. Frame shall have vertical & horizontal members, vertical

channels have inbuilt groove with rectangular slots to fix cantilever / gable end brackets. Frame to frame shall be

attached through male/ female hook mechanism pressure die casted parts made in zinc alloy Mazak5. Adequate ribs

to be given in extrusion profiles having variable thicknesses of 1.10mm to 2.50mm for better durability. Frame to post

shall be attached by male/female hooks made up of 2mm thick CRCA material zinc passivated to 10-12 microns. Each

frame shall be fitted with tiles, male & female hooks, two end cap at top and bottom. Bottom caps shall be provided

with leveller fixing arrangement. all caps shall be of aluminium ADC-12 pressure die cast. top trip shall be flat

aluminium confirming to DIN ISO-2768-1. The data & power cables provision to be given at different levels. skirting

raceways shall be designed for snap fitting for data cables and for power cables raceway below worktop shall be

provided. Tiles of overall thickness 6mm thickness constructed out of PLPB E-1 norms upholstered with

fabric/Laminated/lacqured glass tile should be slide to the grooves provided in aluminium frame vertically, two tiles on

either side of the frame to complete the assembly.

Mobile Drawer Unit : It shall be of size of 400 x 450 x 600 (WDH) mm made up of 18mm thick Pre-laminate particle board

as per E1 norms and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Drawer front &

sides shall be made up of 18mm, back 9 mm thick pre laminated particle board of E1 grade with visible edges sealed

with 2mm PVC edge band. The drawer side surface shall be provided with finger groove handle-less design. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered

towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock

shall be provided. Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of

5% to be considered in pipe thickness & Pipe sizes.

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 995 to 1095 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable

Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The

Chair should be provided with Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the

35 WORKSTATION CHAIR NOS 24.00 21,270.36 510,488.52

tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with

height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x

18mm made of Delrin P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made

up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength.Tolerance of +/- 5mm to

be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness &

Providing and fixing of low height storage with/ without planter top. The depth of the storage shall be upto 450mm. Top

shall be made up of 18mm thick pre laminated particle board E1 norms and Back shall be made up of 9 mm thick pre

laminated particle board with 2mm PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated

particle board. Shutters to be provied for compartment. Planter Box Shall height of 150mm to keep the planter pot.

36 LOW HEIGHT STORAGE sqm 75.00 19,826.74 1,487,005.43

Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged doors top shall be provided with finger

groove handle-less design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile

edge of 6mm straight surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. Cam Lock faciltity should be provided for safe storage of documents.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing and fixing of storage of depth upto 500mm. Top shall be made up of 18mm thick pre laminated particle

board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping,

Shutters shall be made up of 18 mm thick pre laminated particle board. Shutters to be provied for compartment. Edge:

37 FULL HEIGHT STORAGE All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged doors top shall be provided with finger sqm 28.00 23,911.74 669,528.70

groove handle-less design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile

edge of 6mm straight surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. Cam Lock faciltity should be provided for safe storage of documents.

Supply and placing of Meeting Table

Overall Size as below. Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping supported on

V Shape aluminium die cast connectors of min size 430 mm L x 110 mm H x 25 mm Thick. 4 Connectors on Main table &

2 on side unit shall be provided. All sides of the worktop except corners of main table shall be provided with 2mm thick

alumimum extrusion of 40mm + 25 mm + 30 MM + 8 mm formed into horizontal & vertical direction to enable support as

well as top surface coverage. edge surface extrusion supporting the worktop to be tappered towards top. Support:

38 End Legs: 50mm thick pre laminated particle board with 2mm PVC edge lipping. Modesty Panel: 18mm thk pre lam

board with 2mm PVC edge lipping of 450mm Ht. Wire Management: Slide Connect with PVC cable dump. Slide

connect Configuration - Standard switch configuration no deviation 2 Power,2 USB Charger,1 Network,1 HDMI.

Sufficient storage space to be priovided in the storage pedestal of the table having drawers at the main table &

hinged door storage below the side unit. The table top will have 10 mm thick Euro bronze glass with white vinyl film hot

laminated and Kuraray pvb interlayer. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

38.1 6 PAX MEETING ROOM TABLE Overall Size : W 2400 x D 1200 x H 750mm. NOS 1.00 247,357.50 247,357.50

11 PAX MEETING ROOM

Supply and placing of Mediation room Table

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its

edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. The OEM shall have ISO 9001, ISO

14001, Bifma Level 2, Green Guard by UL, India Design Mark & IGBC Gold rated factory certification. . Two Long sides

of the work surface shall be provided with reverse tapered edge design created by chamfering the board at 45

degree inside for 17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic

39 MEDIATION CENTER TABLES

machine. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number “7” shape &

oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm table height, it shall

acts as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube &

connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast 90deg – 02 way

connectors. Wire Management: 350mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable

dump and Vertical wire entry cover made up of steel sheets.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of chair. The overall size of Chair shall be : width 600 +/-5mm, depth 640 +/-5mm. Total height 1170

to 1270 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm

and Seat height 470mm to 570 mm +/-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density. hardness

of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be made up of foam pre moulded at 55 kg/m3 density.

hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster

180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be

supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey shade,

armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar Support

made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar Support

MEETING ROOM HIGH BACK material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock Mechanism

CHAIR (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The mechanism shall

allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied

with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm to 260mm

adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4

tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 980 to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar

Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock

MEETING ROOM MID BACK

40 Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The NOS 58.00 23,678.67 1,373,362.67

mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height)

to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm

to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Supply and placing of Single Sided Book Rack : The overall size of the book rack shall be 900 L X 350 D X 1950 (LDH)mm.

Uprights shall be made up of - MS Pole 40 x 40 x 1.6 Tube having slot single side, size of 25 x 5mm rctangular slot to

support the partition bracket having overall size of 300 x 99mm. Two U channel shall be welded with MS square pole

size of 13 x 10 x 13 and have 1mm thick for support of back panel. Shelves should be made of MS powder coated

41 LIBRARY BOOK SHELFS NOS 13.00 39,260.87 510,391.30

metal 1.2mm, supported with hat shaped brackets size of 9 x 10 x 20 x 10 x 9mm and overall size of 36 x 10mm. Back

Panel shall be made up of MS Powder coted metal 0.8mm. Top panel, Side Panel & Bottom Panle shall be made up of

18mm thick PLT. Skriting shall be provided of size of 900 x 40mm. Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supplying, and placing in position of reception Table as per Image/drawing in engineered wood.Table top made of

25mm thick HDHMR board with both sides laminated, side panel's made of 18mm thick Laminated HDHMR board .

Combination construction of reception desk above table top 18 mm thick. Counter top to table top height @ 300mm,

overall reception desk height is @ 1050mm with counter top, table top made of 25 mm thick Laminated HDHMR board

work surface with the exposed edges finished with 2mm thick pvc edge binding tape of matching colour and shade

42 RECEPTION TABLE

fixed with hot melt glue. Along with 18mm thk HDHMR additional modesty panel of size 1350 mm (l) x 700 mm (h).1

mobile pedestal (2 drawers + 1 filing cabinet) of size 450 mm (l) x 450 mm (d) x 725 mm (h) provided with central lock's

for security and handles provided for easy opening & pedestal's move on nylon castors. The product should be from

manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/ AIOTA Certification. The product

should be as per above given specification subject to approval of Engineer in charge.

Dimension(L) 2000mm X (D) 750mmX (H) 750mm (all over ht 1050mm) NOS 1.00 189,879.24 189,879.24

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 995 to 1095 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable

Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The

Chair should be provided with Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the

43 RECEPTION CHAIR NOS 1.00 21,270.36 21,270.36

tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with

height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x

18mm made of Delrin P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made

up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength.Tolerance of +/- 5mm to

be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness &

Supply and placing of 2-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 1545L x 880D x 840H. The seat/back mounting frame assy. holds the two

side frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure

shall be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should

be used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall

be used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and

RECEPTION & WAITING

44 back are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best NOS 2.00 64,858.96 129,717.91

LOBBY SOFA - 2 SEATER

seating comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be

elevated from ground by about 3 inches using metal powder coated legs, which shall create provision for easy

cleaning at the same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more

than 50K rubs, colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best

feel & comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of 1-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 900L x 880D x 840H. The seat/back mounting frame assy. holds the two side

frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure shall

be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should be

used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall be

used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and back

RECEPTION & WAITING

45 are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best seating NOS 4.00 54,576.35 218,305.39

LOBBY SOFA - 1 SEATER

comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be elevated

from ground by about 3 inches using metal powder coated legs, which shall create provision for easy cleaning at the

same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more than 50K rubs,

colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best feel &

comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of Centre table Size

The overall size of the Centre table shall be 1050 mm Length x 550 mm depth, 450 mm height. the table top shall be

made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion surface shall be

provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC. Under

46 CENTER TABLE Structure Support: Table top shall be supported on CRCA legs duly powder coated. The Chair understructure should be NOS 3.00 14,538.11 43,614.34

provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom. The edges of the table top

shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker on the top & thinner on the

bottom side. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of corner tabl. The overall size of the corner table shall be dia 600mm, 450 mm height. the table

top shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion

surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any

VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The table

understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom.

The edges of the table top shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker

on the top & thinner on the bottom side.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of Compactor-Overall Dimesnion: 900mm(l) X 450mm (D) x 2080mm(H)

Supplying, and placing in position of compactor . Designed for long life and

easy part replacement. Uses one common aisle spacethat optimizes available space. PU drive wheel for firm grip and

hassle-free mobility. Channel stoppers prevent derailment. Label holders with neat transparent acrylic sheets facilitate

easy identification. Locking stiffeners for centralised locking ensures safety of documents. Rotating locks with easy to

identify lock/unlock positions ensures safety. Shims providedbelow the rails for right laveling All the shelf & body shall be

made out of 0.8mm thk ms powder coated (50 microns thickness) od approved shade.The product should be as per

above given specification subject to approval of EIC

Supply and placing in place of training chair. The overall size of Chair shall be: Total height 885 +/-5 mm, Back Width

415mm at Top and 470mm at bottom, Seat Width 490 +/-3 mm, Seat Depth 465+/-3 mm and Seat height 495mm +/-

5mm . Over all chair width should be 600 +/-5mm and Overall chair depth should be 585 +/-5mm. Seat shall be

upholstered with 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one

hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall

be supplied with Mesh at the back rest. The OEM shall have ISO 9001, ISO 14001, Bifma Level 2, Green Guard by UL,

India Design Mark & IGBC Gold rated factory certification.. The chair shall be supplied with injuction moulded Back

49 TRANING CHAIRS NOS 28.00 11,943.59 334,420.55

rest with material of PA620%GF. The Chair understructure should be provided with 25.4x1.6 mm thickness Round tube.

understructure shall connected with 4nos 50mm dia Twin castors PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. the axle pin shall be rust protected zinc passivated. Understructure shall powder coated upto 40microns.

Fixed arms connected to Back rest with Textured arm pad with size of 290x38x3.5mm. Understructure shall powder

coated upto 40 to 60microns. Injection moulded ABS writing tablet with370mm lenght, 265mm width and 10 thickness

shall assembled for arm rest. Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and

tolerance of 5% to be considered in pipe thickness & Pipe sizes.

TOTAL OF 5TH FLOOR 15,270,373.01

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supplying, and placing in position of reception Table as per Image/drawing in engineered wood.Table top made of

25mm thick HDHMR board with both sides laminated, side panel's made of 18mm thick Laminated HDHMR board .

Combination construction of reception desk above table top 18 mm thick. Counter top to table top height @ 300mm,

overall reception desk height is @ 1050mm with counter top, table top made of 25 mm thick Laminated HDHMR board

work surface with the exposed edges finished with 2mm thick pvc edge binding tape of matching colour and shade

1 RECEPTION TABLE

fixed with hot melt glue. Along with 18mm thk HDHMR additional modesty panel of size 1350 mm (l) x 700 mm (h).1

mobile pedestal (2 drawers + 1 filing cabinet) of size 450 mm (l) x 450 mm (d) x 725 mm (h) provided with central lock's

for security and handles provided for easy opening & pedestal's move on nylon castors. The product should be from

manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/ AIOTA Certification. The product

should be as per above given specification subject to approval of Engineer in charge.

Dimension(L) 3000mm X (D) 750mmX (H) 750mm (all over ht 1050mm) NOS 1.00 284,818.35 284,818.35

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 995 to 1095 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable

Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The

Chair should be provided with Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the

2 RECEPTION CHAIR NOS 2.00 21,270.36 42,540.71

tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with

height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x

18mm made of Delrin P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made

up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength.Tolerance of +/- 5mm to

be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness &

Supply and placing of 2-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 1545L x 880D x 840H. The seat/back mounting frame assy. holds the two

side frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure

shall be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should

be used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall

be used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and

RECEPTION & WAITING

3 back are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best NOS 7.00 64,858.96 454,012.70

LOBBY SOFA - 2 SEATER

seating comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be

elevated from ground by about 3 inches using metal powder coated legs, which shall create provision for easy

cleaning at the same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more

than 50K rubs, colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best

feel & comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of 1-SEATER SOFA

Overall Dimensions of 2 seater soaf shall be, 900L x 880D x 840H. The seat/back mounting frame assy. holds the two side

frames together. the mounting frames, 2nos should be used to connect the side frames. Sofa inner frame structure shall

be made from the combination of treated solid wood (Neem / Pine wood) and plywood, webbing belts should be

used to have good strength, rigid & stable construction to ensure higher durability. The polyurethane (PU) foam shall be

used in Seat & back rest having 40 density and 32 density respectively. Leatherette/ fabric upholstery Seat and back

RECEPTION & WAITING

4 are upholstered using leatherette/fabric of Aprooved make shall be ergonomically designed to offer the best seating NOS 23.00 54,576.35 1,255,256.00

LOBBY SOFA - 1 SEATER

comfort, Seat height should be normally between 17 to 18 inches and depth of 20-22 inches. Sofa shall be elevated

from ground by about 3 inches using metal powder coated legs, which shall create provision for easy cleaning at the

same time offers floating look. The Fabric used for upholstery shall have abrasion resistance of more than 50K rubs,

colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality Fabric to offer the best feel &

comfort.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of Centre table Size

The overall size of the Centre table shall be 1050 mm Length x 550 mm depth, 450 mm height. the table top shall be

made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion surface shall be

provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC. Under

5 CENTER TABLE Structure Support: Table top shall be supported on CRCA legs duly powder coated. The Chair understructure should be NOS 7.00 14,538.11 101,766.79

provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom. The edges of the table top

shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker on the top & thinner on the

bottom side. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC

Gold rated factory certification, India Design Mark.

Supply and placing of corner table. The overall size of the corner table shall be dia 600mm, 450 mm height. the table

top shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion

surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any

VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The table

understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom.

The edges of the table top shall be rounded & edges shall not be sharp. The legs shall be in angular design & thicker

on the top & thinner on the bottom side.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Providing and placing of 3 Pax triangular Café Table of each size upto 1350mm, Worktop shall be made out of 25mm

thick E-1 grade (Environmentally Friendly) particle board cover with laminate and all the edges of worktop shall be

provided with machine pressed 1.5-2 mm thick ABS edge banding glued with hot melt EVA glue. E1 grade laminate

7 CAFETERIA TABLES NOS 7.00 27,131.13 189,917.91

with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air

quality. The under structure is made of MS Powder coated Pole base leg with supporting MS plate. Product should be

BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing and fixing Cafe chair of Size - 400mm (W) x 500mm (D) x 830mm (H) 450SH. Seat / Backrest: Polypropylene

plastic (PP) injection in a specific design. The seat and back are made up injection moulded high impact strength

8 CAFETERIA CHAIRS polypropylene polymer (PP) compound with indoor grade UV Resistance. Base: PP Base. Leveller are made of high NOS 21.00 10,395.72 218,310.07

impact strength polypropylene polymer compound with indoor grad UV Resistance and pressed fitted with tubular

frame. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing and fixing tables of High table Counter - High Café Table of size: 1450Wx 500Dx 1050Hmm. High Table top is

made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding

(PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated

method) for better in-house quality. This should comply with (EN 120-1992).The understructure is made of MS Powder

coated PLoe base leg with supporting MS plate. Product should be BIFMA gold rated SCSglobal certified for inhouse

air quality and with 05 years warranty.

Providing and fixing tables of High Chair, High chair of size: 480Wx 440Dx 990Hmm & seating Height is 760 mm. Seat &

10 HIGH STOOLS Understurcture are madeout of teak wood with melamine plish.Product should be BIFMA gold rated SCSglobal NOS 8.00 16,481.15 131,849.22

certified for inhouse air quality and with 05 years warranty.

Supply and placing of Meeting Table

Overall Size as below. Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping supported on

V Shape aluminium die cast connectors of min size 430 mm L x 110 mm H x 25 mm Thick. 4 Connectors on Main table &

2 on side unit shall be provided. All sides of the worktop except corners of main table shall be provided with 2mm thick

alumimum extrusion of 40mm + 25 mm + 30 MM + 8 mm formed into horizontal & vertical direction to enable support as

well as top surface coverage. edge surface extrusion supporting the worktop to be tappered towards top. Support:

11 6 PAX MEETING ROOM TABLE End Legs: 50mm thick pre laminated particle board with 2mm PVC edge lipping. Modesty Panel: 18mm thk pre lam

board with 2mm PVC edge lipping of 450mm Ht. Wire Management: Slide Connect with PVC cable dump. Slide

connect Configuration - Standard switch configuration no deviation 2 Power,2 USB Charger,1 Network,1 HDMI.

Sufficient storage space to be priovided in the storage pedestal of the table having drawers at the main table &

hinged door storage below the side unit. The table top will have 10 mm thick Euro bronze glass with white vinyl film hot

laminated and Kuraray pvb interlayer. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 980 to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar

Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock

12 6 PAX MEETING ROOM CHAIR Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The NOS 6.00 23,678.67 142,072.00

mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height)

to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm

to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and

anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided

with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat &

back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish

with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam,

100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm

thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden

13 SOFA FOR JUDGES LOUNGE Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood

polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper

support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 -

180mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and

shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as

directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and

with 05 years warranty.

13.1 3 seater sofa overall dimension - 1950mm W x 760-780mm D x 680-700mm H NOS 2.00 93,985.85 187,971.70

13.2 2 seater sofa overall dimension - 1550mm W x 760-780mm D x 680-700mm H NOS 6.00 69,432.85 416,597.09

13.3 1 seater sofa overall dimension - 810mm W x 760-780mm D x 680-700mm H NOS 10.00 40,564.89 405,648.91

Providing and fixing tables of Centre table Size - 900mm W x 600mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

CENTER TABLE FOR JUDGES

14 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 8.00 16,735.41 133,883.30

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

Providing and fixing tables of Side table Size - 500mm W x 500mm D x 365mm H for whose top & Base are made of

Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC)

CORNER TABLE FOR JUDGES

15 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) NOS 10.00 14,706.93 147,069.35

for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of Meeting Table

Overall Size as below. Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping supported on

V Shape aluminium die cast connectors of min size 430 mm L x 110 mm H x 25 mm Thick. 4 Connectors on Main table &

2 on side unit shall be provided. All sides of the worktop except corners of main table shall be provided with 2mm thick

alumimum extrusion of 40mm + 25 mm + 30 MM + 8 mm formed into horizontal & vertical direction to enable support as

well as top surface coverage. edge surface extrusion supporting the worktop to be tappered towards top. Support:

16 LAWYERS BREAKOUT ROOM End Legs: 50mm thick pre laminated particle board with 2mm PVC edge lipping. Modesty Panel: 18mm thk pre lam

board with 2mm PVC edge lipping of 450mm Ht. Wire Management: Slide Connect with PVC cable dump. Slide

connect Configuration - Standard switch configuration no deviation 2 Power,2 USB Charger,1 Network,1 HDMI.

Sufficient storage space to be priovided in the storage pedestal of the table having drawers at the main table &

hinged door storage below the side unit. The table top will have 10 mm thick Euro bronze glass with white vinyl film hot

laminated and Kuraray pvb interlayer. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supply and placing of chair. The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall

be 980 to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100%

polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair

shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar

Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock

17 CHAIR Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The NOS 52.00 23,678.67 1,231,290.67

mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height)

to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm

to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be

class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of

chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered for product

sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The OEM shall have

ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification,

India Design Mark.

Proving and placing of V-type table of depth 750mm. Worktop shall be Made of 36mm thick MDF finished with 12mm

thick bendable acrylic solid surface. The acrylic solid surface to be wraped around edges to have tapered nosing as

per design. The Under-structure shall be made of 25mm thick prelaminate partical board with 2mm pvc edge banding

all the visible side. Modesty Panel shall be made up of 18mm thick 600mm ht plt modesty panel should be considered.

It shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any

ARBITRATION ROOM TABLE -

18 VOC. Wire Management: The metal Raceways shall provided below the work surface for carrying wires from one end RMT 115.00 15,797.83 1,816,750.00

to other end of the table, With vertical wire entry cover. The raceway shall be made of 0.8mm CRCA with duly powder

coated. 450 mm Anodised flip up Made of Aluminum in anodised finish, that shall have soft closure and three way wire

acess . Per table one 450 mm flip up and cable tray shall be provided for easy wire access.The OEM shall have ISO

9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Proving and placing of rectangular/ tapered-type table as per layout/ drawings. Worktop shall be Made of 36mm

thick MDF finished with 12mm thick bendable acrylic solid surface. The acrylic solid surface to be wraped around

edges to have tapered nosing as per design. The Under-structure shall be made of 25mm thick prelaminate partical

board with 2mm pvc edge banding all the visible side. Modesty Panel shall be made up of 18mm thick 600mm ht plt

modesty panel should be considered. It shall be provided with machine pressed 2mm thick imported PVC lipping

ARBITRATION ROOM TABLE -

19 glued with hotmelt Eva glue free from any VOC. Wire Management: The metal Raceways shall provided below the SQM 48.00 42,469.04 2,038,514.09

work surface for carrying wires from one end to other end of the table, With vertical wire entry cover. The raceway

shall be made of 0.8mm CRCA with duly powder coated. 450 mm Anodised flip up Made of Aluminum in anodised

finish, that shall have soft closure and three way wire acess . Per table one 450 mm flip up and cable tray shall be

provided for easy wire access.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark. The top shall be measure for payment.

Supply and placing of chair. The overall size of Chair shall be : Total height 1050 to 1150 +/-5 mm, Back Width 480 mm

at Top and 470mm at bottom, Seat Width 490 +/-5 mm, Seat Depth 460+/-5 mm and Seat height 440mm to 540 mm +/-

5mm range. And over all chair width should be 560 +/-5mm and Overall chair depth should be 660 +/-5mm. Seat and

back should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat and back shall be made up of PU foarm pre moulded at 55kg/m3 density. Hardness of 25+

3kg at 50% deflection conforming to IS 3400. Seat and back shall be upholtered with leatherette 75% PVC & 25%

polyster - 640 GSM, Abrasion - 100000 cycles. The Chair should be provided with synchro mechanism with single lever

ARBITRATION ROOM HIGH with one position lock. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One

BACK CHAIR Way Adjustable Arms (Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon

Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle

pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged bases made up of

PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe

sizes. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Supply and placing of chair. The overall size of Chair shall be : Total height 950 – 1050 +/-5 mm, Back Width 480 mm at

Top and 470mm at bottom, Seat Width 490 +/-5 mm, Seat Depth 460+/-5 mm and Seat height 440mm to 540 mm +/-

5mm range. And over all chair width should be 560 +/-5mm and Overall chair depth should be 660 +/-5mm. Seat and

back should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400.Seat and back shall be made up of PU foarm pre moulded at 55kg/m3 density. Hardness of 25+

3kg at 50% deflection conforming to IS 3400. Seat and back shall be upholtered with leatherette 75% PVC & 25%

polyster - 640 GSM, Abrasion - 100000 cycles. The Chair should be provided with synchro mechanism with single lever

ARBITRATION ROOM MID with one position lock. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One

BACK CHAIR Way Adjustable Arms (Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon

Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle

pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged bases made up of

PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe

sizes. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Supplying, and placing in position of steno table of overall size 1200mm X 600mm x 750mm (H). Table top made out of

25mm thk laminated HDHMR board with 2mm thk pvc edge banding with ms powder coated "C" shape legs of size 50

STENO TABLE IN ARBITRATION x 50mm. Comprising of metal powder coated cross connectors of size 40mm X 40mm. . The working edges shall be

ROOMS provided with machine pressed 2mm thick PVC edging using special hot melt glue . The product should be from

manufacturer(OEM) which have BIFMA Certification /GREEN PRO Certification/ AIOTA Certification.The product should

be as per above given specification subject to approval of EIC

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and placing of chair. The overall size of Chair shall be : Total height 950 – 1050 +/-5 mm, Back Width 480 mm at

Top and 470mm at bottom, Seat Width 490 +/-5 mm, Seat Depth 460+/-5 mm and Seat height 440mm to 540 mm +/-

5mm range. And over all chair width should be 560 +/-5mm and Overall chair depth should be 660 +/-5mm. Seat and

back should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400.Seat and back shall be made up of PU foarm pre moulded at 55kg/m3 density. Hardness of 25+

3kg at 50% deflection conforming to IS 3400. Seat and back shall be upholtered with leatherette 75% PVC & 25%

polyster - 640 GSM, Abrasion - 100000 cycles. The Chair should be provided with synchro mechanism with single lever

STENO CHAIR IN with one position lock. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One

ARBITRATION ROOMS Way Adjustable Arms (Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon

Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle

pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged bases made up of

PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe

sizes. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold

rated factory certification, India Design Mark.

Providing and fixing of custom made running sofa as per detail drawings. All visible surface to be cladded with 1mm

RUNNING SOFA IN thick decorative laminate as per approval. The sofa to have 75mm-100mm thick cushion on seat and back.

ARBITRATION ROOM Intermidiate arm rest to be provided. The cost to include making cut out of electrical boxes, etc. complete as per

satisfaction of engineer-in-charge.

Providing and fixing of low height storage with/ without planter top. The depth of the storage shall be upto 450mm. Top

shall be made up of 18mm thick pre laminated particle board E1 norms and Back shall be made up of 9 mm thick pre

laminated particle board with 2mm PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated

particle board. Shutters to be provied for compartment. Planter Box Shall height of 150mm to keep the planter pot.

25 LOW HEIGHT STORAGE sqm 56.00 19,826.74 1,110,297.39

Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged doors top shall be provided with finger

groove handle-less design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile

edge of 6mm straight surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. Cam Lock faciltity should be provided for safe storage of documents.

TOTAL OF 4TH FLOOR 18,140,075.69

TOTAL OF 5TH & 4TH FLOOR 33,410,448.70

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji

Nagar, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SECTION DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 0.00 505,767.96

B WATER SUPPLY 408,629.80 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 615,138.00 0.00

D SPRINKLER PIPING & ACCESSORIES 4,875,983.00 505,969.05

Total Cost ( Carried Forward) in Rs. 6,911,487.81

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SUB HEAD A: SANITARY FIXTURES & FITTINGS

SL. NO. DSR - DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Supply, installation, testing and commissioning of glazed

vitreous china single trap syphonic pattern having back

inlet, supporting chair, wall hung water closet complete

with all internal fittings/ accessories and CP brass flush bend

1 MR (European type) water closet with seat and lid, with C.P.

brass hinges and rubber buffers, adapter, rubber joints fixed

to W.C., C.P. brass screwed washers including cutting and

making good the walls and floors wherever required and

HDPE WC pan connector including jointing with white

cement complete in all respects.

Wall hung W.C. pan (White colour)with white plastic seat &

lid "Thermoset moulded ( bakelite ) IS 2548 Part I Each 5 27,825.34 139,126.70

Supply, installation, testing and commissioning of concealed

2 MR cistern including flush plate and all internal fittings/

accessories including cutting and making good the walls

and floors wherever required complete in all respects. Each 5 12,365.33 61,826.67

Supply, installation, testing and commissioning of glazed

vitreous china wash basin with R.S. or C.I. brackets painted

white, 32mm C.P. brass waste of standard pattern , C.P

3 MR brass wall flange 32 mm dia. C.P. brass bottle trap and

union 32 mm dia C.P. pipes to wall flange. complete

including cutting and making good the walls wherever

3.1 Undercounter wash basin Each 1 8,363.70 8,363.70

3.2 Table top wash basin Each 4 15,063.73 60,254.91

Supply, installation, testing and commissioning of 15mm C.P.

brass single hole wash basin mixer without popup waste

system with 450mm long copper pipes and brass nut Each 5 6,064.37 30,321.87

Providing & fixing toilet paper holding including cutting and

making good the walls. Each 5 1,566.63 7,833.13

Providing & fixing Horizontal liquid soap dispenser with

6 MR stainless steel lid and brackets fixed to wooden cleats with

C.P. brass screws. Each 5 3,714.79 18,573.93

Providing & fixing C.P. brass coat hooks fixed on toilet door

with C.P. brass screws Each 5 618.70 3,093.50

Providing & fixing beveled edge mirror 5.5mm thick of

superior quality plate glass complete with 6mm thick marine

8 MR ply sheet ground fixed to wooden cleats with CP brass

screws and washerswith 40 mm wide teak wood frame as

per design including polishing Sqm 5 2,815.06 14,075.31

9 MR Providing & fixing Hand Shower (Health Faucet) with 8mm

dia, 1M long PVC tube and wall hook CP brass wall flange Each 5 1,786.14 8,930.72

Providing & fixing, testing and commissioning of storage type

electric water heater with automatic thermostatic control

10 MR electric element, pressure release valve, brackets fixed to

expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever

Digitally signed by AMIT

SL. NO. DSR - DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

05 litres capacity (Horizontal /Vertical type1.5 kw electrical

Providing & fixing wall mounted 25 mm dia Stainless steel

11 MR coated grab bar including cutting & making good the

walls(size 450mm long) Each 5 1,041.09 5,205.46

Providing & fixing 15 mm dia C.P. brass bib cock with C.P.

wall flange of approved quality. Each 5 1,585.89 7,929.44

FRAGRANCE DISPENSER MACHINE :-Providing and fixing of

Automatic Fragrance Dispenser machine complete with

refill can and 'C' size battery (2 Nos) for operation fixed to

wooden cleats with CP brass screws Each 5 4,623.87 23,119.33

Providing and fixing of stainless steel finish Paper Towel

14 MR Dispenser having capacity of 300-350 paper towels fixed to

wooden cleats with C.P. brass screws Each 5 5,556.35 27,781.74

Providing and fixing of wall mounted fully automatic hand

15 MR dryer in SS/ black finish as per approval complete will all

accessories. Each 5 5,902.96 29,514.81

Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary fixtures

shall be selected by Architect/Interior designer/Project

manager and the same shall be binding for execution.

No additional fixing cost shall be paid for change in type of

sanitary fixtures.

Contractor to receive all the above mentioned items &

store at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 505,767.96

Digitally signed by AMIT

SUB HEAD B: WATER SUPPLY

SL. DSR Rate DSR Amount NS Amount

(CIVIL) DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

18.7.3 25 mm nominal outer dia pipes. Metre 80.00 401.55 32,124.00

18.7.4 32 mm nominal outer dia pipes. Metre 135.00 518.75 70,031.25

18.7.5 40 mm nominal outer dia pipes. Metre 20.00 702.95 14,059.00

18.7.6 50 mm nominal outer dia pipes. Metre 60.00 934.15 56,049.00

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

2 18.8 clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the the same including testing

of joints complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the

18.8.2 20 mm nominal outer dia pipes. Metre 160.00 537.60 86,016.00

18.8.3 25 mm nominal dia Pipes Metre 75.00 627.25 47,043.75

18.8.4 32 mm nominal dia Pipes Metre 100.00 739.00 73,900.00

Providing and fixing brass stop cock of approved quality

Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end):

Digitally signed by AMIT

SL. DSR Rate DSR Amount NS Amount

(CIVIL) DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

Providing and fixing C.P. bass angle valve for basin mixer and

5 18.53 geyser points of approved quality conforming to I.S:8931 a) 15

mm nominal bore.

Providing and fixing unplasticised P.V.C connection pipe with

PTMT Nuts coller and bush of approved quality and colour.

18.74.2 15mm nominal bore with 45cm length Each 25.00 121.90 3,047.50

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 408,629.80

Digitally signed by AMIT

SUB HEAD C: INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)

SL. DSR Rate NS Rate DSR Amount NS Amount

(CIVIL) DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

2 17.35 Providing and fixing soil, waste and vent pipes.

17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 Metre 150.00 1,180.75 177,112.50

17.35.2 75 mm diameter :

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Metre 125.00 1,186.00 148,250.00

Providing and fixing single equal plain junction of reqd. degree with

3 17.43 access door, insertion rubber washer 3mm thick, bolts and nuts

17.43.1.2 Sand cast (spun) iron pipe IS-3989 Each 12.00 925.70 11,108.40

17.43.2.2 Sand cast (spun) iron pipe IS-3989 Each 10.00 665.05 6,650.50

4 17.44 Providing and fixing single equal plain junction of reqd. degree.

17.44.1.2 Sand cast (spun) iron pipe IS-3989 Each 12.00 811.90 9,742.80

17.44.2.2 Sand cast (spun) iron pipe IS-3989 Each 10.00 561.20 5,612.00

Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.

17.38.1.2 Sand cast iron S&S as per IS - 3989 Each 12.00 705.20 8,462.40

17.38.2.2 Sand cast iron S&S as per IS- 3989 Each 10.00 522.80 5,228.00

6 17.39 Providing and fixing bend of required degree .

Digitally signed by AMIT

SL. DSR Rate NS Rate DSR Amount NS Amount

(CIVIL) DESCRIPTION OF ITEMS UNIT Qty

17.39.1.2 Sand cast iron S&S as per IS : 3989 Each 12.00 570.05 6,840.60

17.39.2.2 Sand cast iron S&S as per IS - 3989 Each 10.00 390.50 3,905.00

7 17.57 Providing and fixing collar.

17.57.1.2 Sand cast iron S&S as per IS - 3989 Each 12.00 513.15 6,157.80

17.57.2.2 Sand cast iron S&S as per IS - 3989 Each 10.00 362.05 3,620.50

Providing and fixing MS holder bat clamps of approved design to

cast iron (spun) pipe embedded in and Including cement concrete

8 17.37 blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) including cost of cutting holes

and making good the walls etc.

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps.

including cutting and making good the walls etc.

18.10.4 32 mm nominal bore Metre 60.00 667.00 40,020.00

18.10.5 40 mm nominal bore Metre 10.00 811.90 8,119.00

Painting G.I. Pipes and fittings with two coats of anticorrosive

bitumastic paint of approved quality

18.40.4 32 mm nominal bore Metre 60.00 22.20 1,332.00

18.40.5 40 mm nominal bore Metre 10.00 25.25 252.50

18.40.6 50 mm nominal bore Metre 40.00 30.50 1,220.00

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

quality) for new work

17.65.1 100mm dia cast (spun) iron S&S pipe Metre 150.00 82.80 12,420.00

17.65.2 75mm dia cast (spun) iron S&S pipe Metre 125.00 62.95 7,868.75

Providing lead caulked joints to sand cast iron/centrifugally

cast(spun) iron pipes & fittings of diameter :.

Digitally signed by AMIT

SL. DSR Rate NS Rate DSR Amount NS Amount

(CIVIL) DESCRIPTION OF ITEMS UNIT Qty

Providing & filling the joints with spun yarn,cement slurry & cement

mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.

15 17.48 Providing and fixing single unequal plain junction of reqd. degree.

17.48.1.2 Sand cast (spun) iron pipe IS-3989 Each 10.00 1,032.40 10,324.00

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 615,138.00 0.00

Digitally signed by AMIT

SUB-HEAD - D - SPRINKLER PIPING & ACCESSORIES

SL. DSR 2025 (E & M) DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

NO. REF. NO. (Rs.) (Rs.) (Rs) (Rs)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

1 27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on

the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic

enamel paint of required shade complete as required :

Supplying, fixing, testing and commissioning of

butterfly valve of PN 1.6 rating with bronze/ gunmetal

2 27.11 seat duly ISI marked complete with nuts, bolts,

washers, gaskets conforming to IS 13095 of following

sizes as required :

Providing and fixing ISI Marked of approved make Fire

4 NS Extinguishers complete with all accessories as per

manufacturer's specifications.

4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 8.00 13,940.64 111,525.11

Mechanical Foam gas cartridge type. 9 Kg capacity

Digitally signed by AMIT

SL. DSR 2025 (E & M) DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

NO. REF. NO. (Rs.) (Rs.) (Rs) (Rs)

ABC dry powder stored pressure type 6 kg capacity

Providing, fixing, testing & commissioning of 15mm dia

5 27.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

6 27.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT male

thread to sprinkler head (Outlet) 15mm NPT female

thread with reducer, nipple, 2 side brackets, center

bracket, stockbar of following sizes complete as

Providing & fixing flow switch in following sizes M.S.

pipe including connection etc as required.

Providing and fixing signages/ evacuation plans

printed on photoluminescent U1000 aluminium sheet

of 1.0 mm (+ -10%) containing lumigen II as base

chemical, covered under UV stablized coating and of

appropriate size including fixing on wall, door, ceiling

etc. with proper clamps, hangers, cleats anchor

fasteners etc. complete in all respacts as diercted by

Engineer-in-charge

Providing, jointing and testing of automaticaly

operated Halotron fire extinguishers(cap-

5kg,temperature rating-68degc,test pressure-30bar)

complete with all accessories/fittings.

TOTAL CARRIED TO SUMMARY 4,875,983.00 505,969.05

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

Summary for E & M Component

Sub Head Descriptions DSR Amounts NDSR Amounts

SH-l EI- Point Wiring, DB, Earthing, Lighting, Cable, Cable Tray, LT Panel 8,143,109.00 19,377,850.30

SH-ll HVAC- Chilled pipe, Duct, Inulation, Grill,VRF, Split ac 29,078,057.00 5,534,687.46

Total Amount 46,349,390.42

Total Amount 46,349,390.42

Digitally signed by AMIT

Name of Work: Interior and Fitout work for IIAC at 4th & 5th Floor, Tower A, World Trade Centre, Nauroji Nagar, New Delhi

Bill of Quantity for E & M Component

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

(SH-I: EI WORKS)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without

independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/

recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including

connections but excluding modular plate etc. as required.

4.5 1.24.7 TV antenna socket outlet Each 30.00 168.00 5,040.00

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular

switches in recess etc. as required.

6 1.28 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch

box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular

plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,

9 1.31 including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. Each 20.00 545.00 10,900.00

upplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including

10 1.32 providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. Each 25.00 659.00 16,475.00

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

upplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug

11 2.18 top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal Each 20.00 1,806.00 36,120.00

cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Fabricating, supplying & installation on surface/ recess 2.0 mm thick factory fabricated GI Sheet raceways

height 40 mm and of totally enclosed with 2 mm thick covered. Two lengths of raceways and junction box

12 MR. shall be joined together to make it dust proof. Chipping and removing screed to install the raceways in floor,

including removal and disposing of debris / fixing in ceiling along with suspender and accessories as per

instruction of Engineer in charge.

Fabricating, supplying & installation on surface/ recess 2.0 mm thick factory fabricated GI Sheet raceways

height 40 mm and of totally enclosed with 2 mm thick covered. Two lengths of raceways and junction box

13 MR. shall be joined together to make it dust proof. Chipping and removing screed to install the junction box in

floor, including removal and disposing of debris / fixing in ceiling along with suspender and accessories as per

instruction of Engineer in charge.

13.1 a 500 mm (wide) x 500 mm (length) X 40 mm (height) Each 60.00 2,760.00 165,600.00

13.2 b 350 mm (wide) x 350 mm (length) X 40 mm (height) Each 50.00 2,290.00 114,500.00

13.3 c 250 mm (wide) x 300 mm (length) X 40 mm (height) Each 35.00 1,870.00 65,450.00

13.4 d 200 mm (wide) x 200 mm (length) X 40 mm (height) Each 50.00 1,660.00 83,000.00

13.5 e 150 mm (wide) x 150 mm (length) X 40 mm (height) Each 80.00 1,270.00 101,600.00

13.6 f 100 mm (wide) x 100 mm (length) X 40 mm (height) Each 180.00 1,080.00 194,400.00

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including

14 1.2 painting in case of surface conduit, or cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess

including cutting the wall and making good the same in case of recessed conduit as required.

16 MR Providing and fixing in position the following pvc flexible conduits including all fixing accessories as required.

16.1 a 20 mm dia flexible conduit with end couplers P/Mtr 250.00 35.00 8,750.00

16.2 b 25 mm dia flexible conduit with end couplers P/Mtr 290.00 45.00 13,050.00

16.3 c 32 mm dia flexible conduit with end couplers P/Mtr 120.00 65.00 7,800.00

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the

existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on

18 2.3 surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution

19 2.4 board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution

board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common

neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note :

Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

Providing and fixing following rating and breaking capacity and pole MCCB with thermo magnetic

21 2.2 release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel,

making connections, etc. as required.

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying and fixing 63 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for

22 inductive load of following poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Triple pole Each 64.00 1,980.00 126,720.00

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit

24 2.14 breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit

25 2.15 breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for

26 2.10 inductive load of following poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supply, installation, testing and commissioning of the following sizes of PVC trunking system with end caps,

bends, elbows complete as required.

Providing and fixing of Gel-Chemical Earthing Electrode of G.I. made as pipe in pipe technology(IS:3043 :

1987)duly CPRI Approved as per following specification:

Length - (3000 mm)

DIA (outer) - (80 mm)

DIA (Inner) - (40 mm)

28 MR DIA-Terminal Strip Hole - (25 mm) Each 4.00 46,890.00 187,560.00

Space Inside Electrodes - (Filled with Conductive Mixture)

Hot Dip Galvanizing - (70 - 100 Microns)

And earth enhancing compound should be used to treat the soil for lowering the effective ground

impedance 50Kg for each earth pit to make it maintenance free and to minimize the ground voltage

potential rise and pit covered with PVC Cover.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including

connection with brass nut bolt, spring, washer excavation and re-filling etc. as required.

Preparation of complete set of MEP drawings including details. A qualified professsional for the purpose shall

be appointed after due appproval from Engineer In Charge.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including

connection with G.I. nut, bolt, spring, washer excavation and re- filling etc. as required.

32 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. P/Mtr 100.00 1,246.00 124,600.00

33 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. P/Mtr 550.00 287.00 157,850.00

34 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. P/Mtr 100.00 84.00 8,400.00

Supplying & Laying of following sizes copper conductor PVC insulated PVC unsheathed

35 unarmoured flexible cables confirming to IS: 7098 (Part-I) 1988 of 1.1 KV in existing open 0.00

masonry duct/surface/raceways/pipe etc complete as reqd.

Supply, installation, testing and commissioning of copper Earth busbar of size 50 X 5 X 400 mm in

36 suitable size MS sheet enclosure made out of 1.6mm thick MS Sheet duly painted with locking Each 4.00 3,502.00 14,008.00

arrangement etc. complete as reqd.

37 8.3 LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt)

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round

/square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and

construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage

AC 140-270 Volt, frequency 50/60 hz, Operating temp range - 5 0C to 40 0C, internal surge protection of 2.5

KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19,

Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum

50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11

report, CCT 3000°K/ 4000°K /5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS

standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all

respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape

size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat

sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die

cast /Extruded aluminium Body including trim .

Supply, installation, testing and commissining of 20W, recessed, 1205mm linear, IP20, LED luminaire with system

efficacy of 105 lumen/watt, and system lumen output of 2100 lumen, operating in an ambient temperature

of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with

high efficiency translucence diffuser and must have provision for end to end seamless connectivity. EMC

package of wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC 62471 for Photo-biological

safety. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul

should be provided. The LED shall comply with L70 life of 50000 burning hours tested at maximum current. The

38 LEDs used should be with CCT of 4000 K and CRI of Minimum 80, with MacAdam CCT binning ≤3 . LED Driver Each 20.00 4,642.38 92,847.54

shall be Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to

operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 3KV internal surge

protection, Power factor of minimum 0.95, driver efficacy of minimum 85% and total harmonic distortion (THD)

of less than or equal to 10% should be integral to the luminaire. Manufacturer shall have inhouse lab

approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 /

Supply, installation, testing and commissioning of 30W, recessed, 1205mm linear, IP20, LED luminaire with

system efficacy of 105 lumen/watt, and system lumen output of 3150 lumen, operating in an ambient

temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in

white with high efficiency translucence diffuser and must have provision for end to end seamless connectivity.

EMC package of wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC 62471 for Photo-

biological safety. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/

Osram/Seoul should be provided. The LED shall comply with L70 life of 50000 burning hours tested at maximum

39 current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80, with MacAdam CCT binning ≤3 . Each 20.00 5,280.10 105,602.04

LED Driver shall be Isolated type, Constant Current topology driver with proper heat sink for heat dissipation

suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 3KV internal

surge protection, Power factor of minimum 0.95, driver efficacy of minimum 85% and total harmonic distortion

(THD) of less than or equal to 10% should be integral to the luminaire. Manufacturer shall have inhouse lab

approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 /

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, installation, testing and commissining of 20W, suspended 1205mm linear, IP20, SMD LED luminaire with

system efficacy of 150 lumen/watt, and system lumen output of 3000 lumen, operating in an ambient

temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in

white with prismatic diffuser and UGR rating <19 and must have provision for end to end seamless

connectivity. Luminaire shall have distribution 70% Down,30% Up .EMC package of wattage of 0.2-0.5 W LEDs

used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant LEDs from

reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall

comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used should be with CCT of

4000 K and CRI of Minimum 80, with MacAdam CCT binning ≤3 . LED Driver shall be Isolated type, Constant

Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of

150V to 270V (nominal rated voltage – 240V) with 3KV internal surge protection, Power factor of minimum

0.95, driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should

be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of

govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above

parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS

15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Dimension: 1203 mm

Supply, installation, testing and commissioning of Integral, SMD 4x1 Backlit LED Panel, IP 20, 36W LED recessed

mounted fixture with system efficacy of minimum 100lm/W and system lumen output of minimum 3600lm,

operating in ambient temperature of 0⁰C to 45⁰C at 50Hz frequency. Luminaire shall have CRCA housing

coated in white with translucent HET diffuser for uniform illumination and wider light distribution. LEDs used in

the product shall comply with IEC 62471. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/

Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life of 50000 burning hours

tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80. LED Driver

shall be Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to

operate in input voltage range of 140V to 300V (nominal rated voltage – 240V) with 4KV internal surge

protection, Power factor of minimum 0.95 and total harmonic distortion (THD) of less than or equal to 10%

should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of

science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to

verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS

Supply, Installation, Testing and Commisioning of IP20 linear suspended standalone fitting made of extruded

aluminium housing and is should have high transmissive diffuser. Fixture should have minimum efficacy at

System level (Not Chip Level) >70lumens/watt(SDCM<3) and a minimum system lumen output of 1260

(downlight) lumens/4ft and maximum system wattage of 18W/4ft. Fixture should have office compliance with

low UGR. Luminaire should have Life of 50,000hrs@L70 Lumen maintenance at 45deg C ambient temperature,

CCT up to 4000/5700K, IP20, IK02, CRI >80, PF >0.95, THD<10% at full load and an operating Voltage Range of

140 - 300V AC, Internal Surge Protection 3KV & driver efficacy >85%. The fixture should comply with the

parameters as per IS10322. Fixture should have class I indulation. Manufacturer shall have inhouse lab

approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters.

Supply, installation, testing and commissioning of Suspended LED stretch fabric with white fabric Luminaire

with edge to edge illumination of required dimension made of extruded aluminum housing delivering

≥2800lumen/sq m and it draws 55W/sq m maximum from standard 220-240V AC supply. Fixture offers excellent

light output, long source life, high CRI, and energy efficiency, in a beautiful, clean plane of light. Industry-best

quality of 80+ CRI and color consistency within a 3-step MacAdam ellipse provides a glare-free direct view

luminaire, and abundant, uniform daylight illumination evenly lit across the entire task surface. Product to be

supplied with specially designed suspensions system. The diffuser shall be Special translucent stretch fabric is

100% Recyclable having good resistance properties -Flame retardant, Non-Flammable, Self extinguishing,

Anti-bacterial, Anti-Fungal and Anti-Static, Impermeable to Water and steam for uniform and optimum light

distribution. Light Reflection Properties with High gloss fabric >80% & Light Transmission Properties Upto 77%. Fire

rated to European standard B-s1-d0 according to EN 13501-1. Having acoustic properties of strecth ceiling:

Reverberation time at 125/250/500/1000/2000 Herts reduces from 1.5s to 0.7s with designed perforations and

insulation.Fixture should have IP20, CCT Range – 4000K/5700/6500k, PF ≥ 0.95, THD<=10%, CRI 80 and drive

should have Surge Protection upto 2KV . The LED Driver shall be easily available in India for repair and service.

The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo

Biological Safety Standard.

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Suppling, installation, testing and commissioning of electrically operated on 220 V, 50 Hz, AC Supply

illuminated exit signage conforming to IS- 10322 for the bank premises ceiling having the following

specifications etc. complete as reqd. (Make:- Prolite Auto Glow, Model No.FASCIA-E)

a. Housing extruded aluminum alloy.

44 b. Diffuser cum message panel-CAD design prnting on 8 mm crystal acrylic sheet. Each 20.00 7,602.00 152,040.00

c. Battery-lithium ion rechargeable battery.

d. Backup time 180 minutes.

e. Charging type - constant current charger.

f. Recharging cycle - 16 to 24 Hours.

Supply, installation, testing and commissioning of LED flexistrip having minimum rating 9.6W/mtr, CCT

45 3000K/4000K, 5 mtr roll with LED Driver lumens nots less than 3800, luminous efficacy not less than 80 Each 50.00 1,384.48 69,223.82

Lumens per watt etc. complete as reqd.

Supply, installation, testing and commissioning of suspended round disc shaped LED decorative fixture of dia

Ø1000mm. . Fixture to be made of extrusion Aluminum housing in white finish with HET plastic diffuser. LED

Used shall be SMD type with Minimum system Lumens 5750 @50W & system efficacy 115lm/W, IP20, Life of LED :

50000 burning Hrs. @ L70 Lumen maintenance, CCT of 4000/5700K (SDCM<=3), CRI >=80, PF >0.95, operating

Voltage Range of 150-270 V AC. Minimum Internal Surge Protection 2.0KV. Manufacturer shall have inhouse

lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted

from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate

Supply, installation, testing and commissioning of suspended round disc shaped LED decorative fixture of dia

Ø600mm. . Fixture to be made of extrusion Aluminum housing in white finish with HET plastic diffuser. LED Used

shall be SMD type with Minimum system Lumens 3300 @30W & system efficacy 110lm/W, IP20, Life of LED :

50000 burning Hrs. @ L70 Lumen maintenance, CCT of 4000/5700K (SDCM<=3), CRI >=80, PF >0.95, operating

Voltage Range of 150-270 V AC. Minimum Internal Surge Protection 2.0KV. Manufacturer shall have inhouse

lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted

from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate

Supply & Laying of following sizes Aluminum conductor armoured PVC insulated PVC sheathed XLPE

cable of grade 1.1 KV in the existing open masonry duct/ surface/ cable tray/ pipe etc complete as reqd.

Supplying and making end termination with brass compression gland and aluminium lugs for following size

of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required.

Supply & Laying of following sizes Copper conductor armoured PVC insulated PVC sheathed XLPE cable of

grade 1.1 KV in the existing open masonary duct/ surface/ cable tray/ pipe etc complete as reqd.

Supplying and making end termination with brass compression gland and Copper lugs for following

size of PVC insulated and PVC sheathed / XLPE Copper conductor cable of 1.1 KV grade as required.

Hot Dipped Galvanized Iron Cable Tray

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying and installing following size of perforated Hot dipped galvanized iron cable tray (Galvanized

thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with

G.I. suspenders including bolts & nuts, painting suspenders etc as required.

52.1 450 mm width X 50 mm depth X 2.0 mm thickness P/Mtr. 100.00 1,325.00 132,500.00

52.2 300 mm width X 50 mm depth X 1.6 mm thickness P/Mtr. 380.00 963.00 365,940.00

52.3 150 mm width X 50 mm depth X 1.6 mm thickness P/Mtr. 300.00 716.00 214,800.00

Main Floor Panel

Fabrication, supplying, installation, Testing & Commissioning of electrical panel of cubical

construction, of suitable size with 800 amp 4P Aluminum Bus Bar insulated with heat shrinkable PVC

sleeve, floor mounted type, fabricated out of 2mm.thick CRCA sheet, compartmentalised with hinged

lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank Each 2.00 677,085.13 1,354,170.26

treatment process, cable alley, inter-connection, having following switchgears and accessories

mounting and internal wiring, earth terminals, numbering etc. Complete in all respect, suitable for

operation on 415 V, 3phase, with neutral 50 HZ. AC

supply etc. complete as reqd.

630 Amp 4P MCCB - 1No

Indicating Light - 6Nos Multifunction Meter with RS485 communication port-1No Control MCB-7Nos

OUTGOING FEEDER

500AMP FP MCCB - 1No.

125AMP FP MCCB - 2Nos.

100A FP MCCB -4Nos

63A FP MCB -4Nos

40A FP MCB -9Nos

UPS OUTPUT PANELS

Fabrication, supplying, installation, Testing & Commissioning of electrical panel of cubical

construction, of suitable size with 200 Amp FP Aluminum Bus Bar insulated with heat shrinkable PVC

sleeve, floor mounted type, fabricated out of 2mm.thick CRCA sheet, compartmentalised with

hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank Each 2.00 380,832.00 761,664.00

treatment process, cable alley, inter-connection, having following switchgears and accessories

54 mounting and internal wiring, earth terminals, numbering etc. Complete in all respect, suitable for

operation on 415 V, 3phase, with neutral 50 HZ. AC

supply etc. complete as reqd.

100 Amp 4P MCCB - 1 No

Indicating Light - 6Nos Multifunction Meter with RS485 communication port-1No Control MCB-7Nos

OUTGOING FEEDER

40A FP MCB -5Nos

Fabrication, supplying, installtion, testing and commissioning of HVAC panel (Outdoor type Weather proof/

exterior grade) suitable size with 630 amp FP Aluminium Bus bar insulated with heat shrinkable PVC sleeve,

floor mounted type, fabricated out of 2mm thick CRCA sheet compartmentalised with hinged lockable

doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley,

inter-connection, having following switchgears and accessories mounting and internal wiring, earth terminals,

numbering etc. Complete in all respect, suitable for operation on 415 V, 50 HZs, Three phase AC supply etc.

complete as reqd.

Incomer:500A FP MCCB- 1 Nos

Multifunction meter with RS-485 PORT CL-1- 1 Nos

Outgoing:63A, FP MCB - 7 Nos, 100A FP MCCB - 2 No., 125A FP MCCB - 1No.

Providing of rubber mat 1 mtr. wide and 12 mm thick to withstand 3.3 KV dielectric strength as per IS

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm

57 thick, and vitreous enameled white on both sides, and with inscription in single red colour on front Each 6.00 269.00 1,614.00

side as required.

Providing First Aid Box as approved by St. John Ambulance Brigade/Indian Red Cross conforming to IS

Supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as

reqd. (approximate front area 1.20 sq. metre)

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

(SH-II: HVAC SYSTEM)

CHILLED WATER HVAC SYSTEM

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air

path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring

return so as to close the damper in the event of power failure automatically and open the same in case

of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted.

The damper shall also be closed in the event of fire signal complete as required and as per

specifications.

Supply, installation, testing and commissioning of GI volume control duct damper complete with

neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume

control dampers as per specifications.

Supplying, & fixing, of powder coated extruded aluminium section return air grills with louvers but without

volume control dampers, complete as per required.

Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly

64 30.19 supported at regular interval as per site requirement etc. complete as required as per 0.00

specifications.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes,

hangers, supports etc. as per approved drawings

and specifications of following sheet thickness complete as required.

Supplying, fixing, testing commissioning of supply air diffusers of powder coated aluminium with aluminium

66 30.17 volume control dampers with anti smudge ring & P/Sqm 10.00 12,841.00 128,410.00

removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without

67 30.18 volume control dampers with anti smudge ring & P/Sq m 10.00 8,595.00 85,950.00

removable core.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell

Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The

joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation

complete as per specifications and as required.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following capacity with

GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller

directly driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V ± 10 %, etc. complete as

70.1 7500 cfm at 15 mm static pressure for fresh air With Class "H" insulation. Each 4.00 151,725.00 606,900.00

70.2 7500 cfm at 15 mm static pressure for fresh air With Class "H" insulation. Each 4.00 147,823.00 591,292.00

70.3 Axial fan control panel Each 8.00 65,621.00 524,968.00

Supply, Installation, Testing and Commissioning of fire retardant flexible Canvas Connection between

Indoor Units and Ducts and Filters for Ducted Units etc. complete as reqd.

Supply, Installation, Testing and Commissioning of inline exhaust fan of 200CFM capacity in toilet area etc.

complete as reqd.

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound attenuator made of

22G GI sheet casing length suitable length consisting of 25mm thick 48kg/m3 density fiber glass wool covered

73 MR with tissue paper ,elliptical volume control damper ,calibrated differential pressure sensor (DPT sensors) at inlet

complete with digital Thermostat,temprature control feature including motorized damper and actuator .(All

VAV shall be factory calibrated).

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, installation, testing and commissioning of Variable Frequency Drive (VFD)

380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

VFD upto 20 HP or as directed by the engineer in charge Nos 2.00 74,948.97 149,897.94

Supply, Installation and Testing of pressure sensors to be installed in supply air ducts.

75 MR Quoted price shall be inclusive of necessary conduting, copper control cabling from the Nos 4.00 17,499.96 69,999.84

sensors to the respective VFDs as per "Approved Shop Drawings".

Supply, Installation, Testing and Commissioning of Digital thermometers as per the

specifications.

77 SITC of Plasma Air Ionization

The Bi-Polar ionization system should consist of Supply, Installation, Testing and commissioning of Bipolar

Ionization System. The Bipolar Ionization System must be a combination of Needle Point Model for Air Handlers

(Needle Point should have Nitinol (nickel titanium) Needles and Carbon Fiber Brush Model for Cassettes and

HI Wall AC units. The System should produce positive and negative ions for creating a Bio Climate rich in ions

and hence neutralizing harmful pollutants including pathogens, Volatile Organic Compounds and Particulate

The Carbon Brush and Self Cleaning nickel titanium based Needle Point Bipolar Ionizer must be UL 2043

certified for Fire and Smoke Safety.

The Carbon Brush and Self Cleaning nickel titanium based Needle Point Bipolar Ionizer must have UL-2998

Certification for Safety against Zero Ozone Emission as per recommendation by ASHRAE.

The Carbon Brush and Self Cleaning nickel titanium based Needle Point Bipolar Ionizer and should be tested

on UL or Intertek/ETL, to prove conformance to UL 867 for electronic devices.

The Technology should have ISO 16000 , CARB and , CSA C22.2# 187 Certifications

Manufacturers shall provide Test report from Internationally/Nationally recognized Lab for proven efficacy on

below pathogens with minimum kill rates for the following pathogens given the allotted time and in a space

a) SARS-CoV-2 (COVID-19) Human Strain

b) MS2 Bacteriophage (Surrogates COVID-19) per CFM 51,000.00 22.09 1,126,435.99

c) Omicron Variant of SARS-CoV-2

e) Total Bacterial Count Reduction rate of more than 90% from NABL Accredited Lab

f) Yeast & Mold/Total fungal count Reduction rate of more than 90% from NABL Accredited Lab

VRV OUTDOOR UNIT

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant

Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type

twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP

modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or

equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency

condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the

rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C

ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39

Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS

compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The

condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the

heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall

performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per

Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD

specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40

and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

For Cooling or Heating or Both

VRV INDOOR UNIT

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan /

dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion

valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc.,

suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units

must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to

adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity Single way wall/corner

VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded

80 31.6 remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as

required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The

system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of

indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be

same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit

equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer

cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ±

10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a

singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C

DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following

nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with

82 31.14 suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-

O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick

insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

82.1 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MTR. 200.00 256.00 51,200.00

82.2 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MTR. 250.00 346.00 86,500.00

82.3 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MTR. 250.00 487.00 121,750.00

82.4 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MTR. 300.00 615.00 184,500.00

82.5 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MTR. 400.00 739.00 295,600.00

82.6 31.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MTR. 400.00 904.00 361,600.00

82.7 31.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MTR. 500.00 1,068.00 534,000.00

82.8 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MTR. 500.00 1,157.00 578,500.00

82.9 31.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm MTR. 600.00 1,222.00 733,200.00

74.10 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm MTR. 650.00 1,286.00 835,900.00

74.11 31.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm MTR. 700.00 1,322.00 925,400.00

74.12 31.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm MTR. 800.00 1,368.00 1,094,400.00

Providing and fixing rigid 25mm UPVC piping complete with fittings, supports, adjustable hangers as per

specifications and duly insulated with 9 mm thick closed cell nitrile rubber insulation etc complete as required.

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in suitable conduits

between indoor and outdoor unit.

85 Timer for Split AC for Server Nos 3.00 3,810.00 11,430.00

(SH-III: FAS & PA )

Supplying, installation, testing and commissioning of micro processor based intelligent addressable main

fire alarm panel, central processing unit with the following loop modules and capable of

supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop

and loop length up to 2 km, network communication card, minimum 320 character

graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non

86 28.2.1 volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The panel shall have facility to connect printer to

printout log and facility to have seamless integration with analog/digital voice evacuation system (which

is part of the schedule of work under SH: PA System) and shall be complete with all accessories. The

panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per

specifications.

28.2.1.2 Two Loop Control Panel Each 1.00 250,420.00 250,420.00

Supplying and fixing of following size Wall Mount

Rack having Fixed Structure with 0.8mm CRCA

Sheet, completely knocked-down condition (CKD)

Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking,

Minimum 2 cable entry/exit provision at Top and

87 39.23 bottom with rubber protection, Front 5mm Toughened

Glass with lock, wall mounting kit, Powder coated

Color- RAL- 7035, complied with UL & RoHS, 2 x 6

sockets 16A power distribution units, 3 numbers

closed cable organizer, Hardware mounting screws

packet of 20 x 1 number, etc. complete as required.

Supplying, installation, testing & commissioning of repeater panel with 320 character/ Touch screen

LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photo thermal

detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of

90 MR rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection Each 10.00 3,871.00 38,710.00

etc. as required.

Supplying, installation, testing & commissioning of response indicator on surface/ recessed MS Box

91 28.2.5 having two LED, metallic cover complete with all Each 140.00 306.00 42,840.00

connections etc as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as

93 28.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. Each 8.00 3,682.00 29,456.00

Supplying, installation, testing & commissioning of addressable fire control module complete as

95 28.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. Each 18.00 3,434.00 61,812.00

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper

conductor having XLPE insulation, steel wire armouring & FRLS/ HFFR outer sheath complete as required.

97 28.2.19 Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. Each 8.00 1,689.00 13,512.00

Supplying, installation, testing & commissioning of intelligent addressable duct detector including

suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as

Public Address System

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player

101 28.3.1 (including 6 zone button paging station) with seamless integration facility with main fire alarm Each 1.00 132,115.00 132,115.00

panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W recess mount ceiling/wall speakers complete

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying, installation, testing & commissioning of digital audio amplifier 250 Watt, 25V rms operating

at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone

assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing

105 28.5.3 surface / recessed steel conduit of following pairs, cores and size including connections and

interconnections etc. as required.

28.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Each 870.00 61.00 53,070.00

SH-IV: (CCTV SYSTEM)

106 40.1 2 MP IP IR Dome Camera

Supplying Installation Testing and Commissioning of 2 MP IP IR Dome Camera having following specifications,

type of lens and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: >50 dB, Camera should display Camera title, Date & Time in

live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum

Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical

IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance upto

50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support,

Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital

3) Compression (Minimum):-Video:- H.265 or better, H.264H, H.264, Audio:- G.711U/A, G.711Mu, G.726, AAC,

4) Wide Dynamic Range:- WDR (120db or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable (Main stream: 2MP (1920 ×1080)@25/30

fps,Sub streams minimum: 720P@25/30 fps).

7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software

or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs,

account lockout, syslog, video encryption, IP/MAC filtering, HTTPS, trusted upgrade, trusted boot.

9) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be

supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device

11) Alarm Trigger : Motion/tampering detection; audio detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL,

DHCP, SMTP, RTSPS, unicast

13) System Capability: ONVIF, Camera shall support open source VMS

14) Ethernet: 1 RJ 45 10/100 Ethernet port

15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter)

and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VAC/PoE (802.3af)/ePoE

18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body

19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing)

20) IR life: 40000 hours or higher

21) Video Bit rate: 32 KBPS - 8 MBPS or better

22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

2MP @ 25/30fps@1080P (1920×1080) Dome Camera with 2.7 to 4 mm ~12 to 13.5mm or better Varifocal

Motorized lens.

107 2 MP IP IR Outdoor Bullet Camera

Digitally signed by AMIT

Sr. No. DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying Installation Testing and Commissioning of 2MP Fixed Lens IP IR Outdoor Bullet Camera having

following specifications and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in

live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum

Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical

IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt Smart IR LED's with effective distance

upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter

support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC,

Digital Watermarking.

3) Compression (Minimum):-Video:- H.265 or better, H.264H, H.264, Audio:- G.711U/A, G.711Mu, G.726, AAC,

4) Wide Dynamic Range:- WDR (120db or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable(Main stream: 2MP (1920 × 1080)@25/30 fps

Sub streams minimum: 720P@25/30 fps).

7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software

or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs,

account lockout, syslog, video encryption, IP/MAC filtering, HTTPS, trusted upgrade, trusted boot.

9) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be

supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device,

11) Alarm Trigger : Motion/tampering detection; audio detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL,

DHCP, SMTP, RTSPS, unicast,

13) System Capability: ONVIF, Camera shall support open source VMS

14) Ethernet: 1 RJ 45 10/100 Ethernet port

15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter)

and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VAC/PoE (802.3af)/ePoE

18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body

19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing)

20) IR life: 40000 hours or higher

21) Video Bit rate: 32 KBPS - 8 MBPS or better

22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

2MP @ 25/30fps@1080P (1920×1080) Outdoor Bullet Camera with 2.7 to 4 mm ~12 to 13.5mm or better

Varifocal Motorized lens.

Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with

camera licenses to record for all channels having specifications and features etc as mentioned below :

1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses for number of

channels of NVR to record per NVR and to provide a live view, storage and simultaneously Multi-channel