Balance work of Canteen Block of Polytechnic College at Shopian

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed: All kinds of soil

Filling with available earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 em), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of EARTH, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in -charge.

Disposal of excavated material from site to site of disposal by mechanical means upto 6 km.

Supply and LAYING of boulders IN MASONARY PATTERN FOR SOAKAGE PITS incl carriage,loading and unloading complete job.

SUPPLY anfd filling of nallah muck inside plinth including carriage ,loading and unloading necessary watering and compaction in layers complete job.

Bricks work with common burnt clay F.P.S (non modular) bricks of class desi- 75 in superstructure including extra charges above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 :6(1 cement : 6 coarse sand)

Application of internal cement sand plaster of thickness 15mm with a cement sand mortar of mix 1:6 including scaffolding curing and including cost of cement,sand.

Application of External cement sand plaster of thickness 15mmwith a cement sand mortar of mix 1:6 including scaffolding curing and including cost of cement,sand.

Providing and laying in position reinforced cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:1½ :3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size. .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - : 1:2 :4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size. .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - : 1:3 :6 (1 cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size. .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4 :8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size. .

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 11.51.1 In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fixing of first class Kailwood glazed shutters 35mm thick for windows and clerestory windows, bright finished of required size with necessery screws, using glass pans 4mm thick (10 kg/sqm) including ISI marked MS Butt Hinges75x60x3.10 mm mm with necessary screws. INCL COST OF GLASS PANS FIXED IN SHUTTERS.

Providing and fixing of first class Kailwood wire gauge shutters 35 mm thick using stainless steel MS wire gauge with wire of dia 0.63 mm and average width of aperture 1.4 mm in both directions for windows and clerestory windows with necessary screws including with hinges and necessary screws : lSI marked M.S. pressed bright finished butt hinges 75x60x3.10 mm mm with necessary screws of required size

Providing and fixing of Kailwood Door shutters 35 mm thick including ISI marked MS Butt Hinges 125x90x4.00 mm with necessaryscrews excluding cost of panelling which will be paid separately.

Providing and fixing of panelling 25 to 40 mm thick of first class Kailwood in Door shutters (Area of opening for panel inserts excluding portion of inside grooves or rebates to be measured)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Applying priming coats with Metal primerWith ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Applying priming coats with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and fixing 16 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm

Providing and fixing of MILD steel Grill panels fabricated from mild steel sections(square bars,flats,ISA ETC.) inclusive electric,machinery charges,adhesives like araldite complete job.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board 610x460mm bowl depth 200mm

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Walls Pillars, Piers, Abutments, Posts and Struts

P/F of below mentioned CP fittings(Jaquar series)or equivalent including c/o screws electric and machinery charges complete job..

CP Brass Sink MIXER(jaquar/marc)

CP Brass Wall MIXER(jaquar/marc)

CP Brass Basin MIXER(jaquar/marc)

CP Brass Bibcock(jaquar/marc)

CP Brass Angle valve(jaquar/marc)

CP Brass Nipples 15mm dia and 20 mm long

CP Brass Grating

CP Brass Soap case

CP Brass Towel Rail with CP Brackets fixed to wooden cleats with CP Brass Screws

Supply, fixing, laying and jointing of GI Pipes of Variable daimeter with fittings like Elbows, Sockets, Tee's, Clamps, Plugs within the building i/c providing of Yarn at joints, inclusive eletric and machinary charge.

15mm Dia GI Pipe(.5'inch)Medium

20mm Dia GI Pipe (.75'inch))Medium

Supply, fixing, laying and jointing of various GI pipe fittings and water controlling devices of Variable daimeter i/c providing of Yarn at joints, inclusive eledtric and machinary charge.

Ball valve (1")

Ball valve (1 1/4")

Union (1/2")

Union (1 ")

Tank nipple (1")

Tank nipple (1 1/4")

Ball cock

Providing and fixing of sintex/comfort or equivalent overhead water tanks in attics within the grid network of pipes including managing of water supply and return with with the facilities of wash out and over flow and alignment.

Providing,fixing,laying of sanitary soil and waste water PVC Prince B Pipes of variable diameter with proper alignment including jointing with solvent complete job.

160mm OD UPVC Prince B Type

110mm OD UPVC Prince B Type

75mm OD UPVC Prince B Type

Supply and fixing of below mentioned PVC fittings in the sanitary system including jointing by solvent.

4"floor trap

4" p trap

4"door bend

4"door T

4" Cowel with cap

3" door bend

3" door Tee

3"floor trap

Providing and fixing of Builders Hardware including cost of screws.

AlUMUNIUM Aldrops 10"

AlUMUNIUM Tower Bolts 6"

AlUMUNIUM Handles 4"

AlUMUNIUM Handles 5"

AlUMUNIUM Tower Bolts 4"

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C. P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Supply, fixing, laying and jointing of insulation for various GI pipeline Using suitable foam exposed to environmental effects

Providing and fixing of water pump 0.5 H.P including starter and all accessories (compton greaves or Kirloskar make)

Cement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand . : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, etc. complete. 50 mmthick with 20mm nominal size stone aggregate. (a) Crushed. Incl cost of 50 mm thick glass strips.

Providing and fixing of 3.5 to 4mm thick glass pans including cost of beading 25mm wide and 15mm thick incl cost of nails

Providing wood work in frames of false ceiling, jam work partitions etc. sawn and fixed in position Budloo wood

Providing and fixing of 12mm thick ply sheets as a base for ceiling veneer over structural framework of Budloo wood joists including cost of nails of variety etc. including scaffolding (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in charge. External work including trenching, refilling etc

3.1PN-16 pipe, 16mm OD(SDR-7.4)

3.2 PN-16 pipe , 20mm OD(SDR-7.4)

3.3PN-16 pipe , 25mm OD(SDR-7.4)

4.1 PPR Union 20mm

4.2 PPR Union 25mm

PPR BALL VALVE 20mm(1/2”)

PPR BALL VALVE 25mm(3/4”)

PPR MALE ELBOWBRASS THREAD20MM X 1/2”

PPR MALE ELBOWBRASS THREAD 25MM x 3/4”

PPR MALE TEEBRASS THREAD20MM X 3/4”

PPR MALE TEEBRASS THREAD25MM x 1/2”

PPR MALE ADAPTOR BRASSTHREAD 20MM X 1/2”

PPR MALE ADAPTOR BRASSTHREAD25MM x 1/2”

PPR FEMALE TEE 20MM X 1/2”

PPR FEMALE TEE 20MM X 3/4”

PPR FEMALE TEE 25MM x 1/2”

Mushtaq Ahmad Dar