Restoration and Rejuvenation of Pond of village Kherki Daula in Ward No.24 Zone 1 MCG.

Amount

Providing and fixing public information board consisting of 75 mm G.I. Pipe of size 2.45 metre x 1.15 metre with 900 mm x 900 mm G.I. Sheet 16 gauge connected/welded with 5 mm thick steel plate of 50 mm duly painted as per column mention in drawing and fixing at site in 60 x 60 x 75 cms cement concrete in 1:2:4 block complete in all respect

(i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with two coats of enamel paint. (iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor and without sitting bench. rates are including with all taxes

Bridge Ladder: 10’L x 2’W x 6’H. Horizontal ladder is of m.s pipe 2” and ¾” and vertical ladder is of same material of 12 gauge ISI mark with suitable PU Primer and PU Paints. Complete item with GST, Transportation, Installation with C.C and labor at site.

Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge and m.s rectangular pipe

NS Item = Supply of RH Pipe 1` dia.

Providing and fixing 3/4`dia Hydrant connection

-Pull Chair and Push Chair ( Two in one ) 1. Dimensions (LxWxH) 1800 x 700 x 1800mm. 2. Fabricated with main post of NB 100mm (G.I) `C` Class pipe of approved make. 3. Seat main frame of NB 50 mm (G.I.) `C` Class pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) `C` Class pipe. 4. Handle frame of pipe NB 32mm and NB 25mm (G.I.) `C` Class. (NB stands for nominal bore i.e. internal diameter of pipe in millimeters. 5. All pipes are powder coated with 80-120 micron thick akzo Nobel or equivalent paints. 6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. 7. Zinc primer paints is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness, coloured, UV resistant and environment friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the Each NSADRate 5.00 32,400.00 162,000.00 Work Name Work Code Sub Division Estimate Amount Lumpsum Amount Total Amount Renovation and Beautification of 10 Nos Parks of Sector-9A and Chath Pooja Ghat of Ward no. 14 Zone 1 MCG GUR01220210412230 155 Gurgaon 17414401.22 0.00 17414401.22 equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS mark, EN16630, DIN 79000 and ISO 14001 international standard for outdoor fitness equipment. 17. Self-explanatory stainless steel label fixed on equipment for ease of use. The rates are inclusive of all taxes like GST, transportation

Air Walker: Providing designing and fixing of Air Walker of size 1100 x 550 x 1480mm fabricated with main post of 114mm dia and 2.5mm thick and rest of pipes or 40mm dia 2.5 mm thick made up of hot rolled tubular steel and hot dipped gaivahized and powder coated 80-120 micron thick using Akzo Nobel or equivalent in desired shade and colour. All welding joints or pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all the welding points prior to finishing. All open ends of pipe to be closed with GI/ LLDPE caps base plate cover shall be made or virgin LLDPE plastic by rotational moulding with minimum 3mm thickness UV resistant and colour as approved by Engineer in charge. High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipments maufactured by reputed company duly oil sealed and self lubricated to be approved by Engineer in charge. The equipment shall be fitted with in built limiters. The equipments shall be fixed on ground with concrete or minimum strength M-25 and J shaped welded bolts and when concrete is set fixing the equipment on to it and cover nuts and bolts with base plate cover all complete as per directions and approval of Engineer in charge regarding material shape of equipment colour all complete as per directions and approval of Engineer in charge regarding material shape of equipment colour (of metal seat and pedal) and fixing of equipments etc (the cement concrete and excavation work shall be paid for separately).

Providing and fixing of Gate valve for hydrant connection

RM181-NP3/NP4 600 dia RCC pipes

Seated chest press: Providing designing and fixing of seated chest press in a pair of size 1800 x 700 x2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick.

texmo motor

-`Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of G.I pipes are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company like SKF to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of G.I pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.` The rates are inclusive of all taxes like GST, Transportation, Installation in CC with 2 years defect liability period free of cost to full satisfaction of engineer in charge complete in all respect.

`-``Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` `

Providing and laying 3/4`dia G.I pipe line.

Bidder Name

Amount

NR ENTERPRISES (GSTN-06AAOFN7557P1ZA) BID ID -1116236

Go Green Leaf(GSTN-NA)--1113400

K & A India Engineering Construction Pvt Ltd(GSTN-NA)--1116136

K & A India Engineering Construction Pvt Ltd

Go Green Leaf

NR ENTERPRISES

K & A India Engineering Construction Pvt Ltd