Re constrcution of PHC at Kiltan Island

Amount

Surface dressing of the ground including removing vegitation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50meter and lift up to 15 meter.(Labour Element)

Earth work excavation by manual means in foundation trenches or drains (not exceeding 1.5m width or 10sqm on plan) including dressing of sides and ramming of bottom,lift up to 1.5,including getting out othe excavated soil and disposal of surplus excavated soil as dirdcted ,withinm a lead of 50mtr. Ordinary Soil (Labour Element)

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundation etc layers not exceeding 20cm in depth consolidating each deposited layers by ramming and watering lead up to 50mtr and lift up to 1.5mtr.(Labour Element)

Filling with Quarry waste/debris ( Dismantled materials issued by department) in trenches, plinth, sides of foundations etc layers not exeeding 20cm plinth, side od foundations etc layers not exceeding 20cm and watering lead up to 50 mtr and lift up to 1.50mtr including loading , transportation and unloading at site.(Labour Element)

Providing and laying cement concrete 1:4:8 (1cement :4 M.sand :8 Granite chips) foundation and plinth .(Labour Element)

Providing and laying cement concrete 1:5:10 (1cement : 5 M.sand : 10 Granite chips) foundation and plinth .(Labour Element)

Providing and laying damp proof course 40mm thick with cement cocrete 1:2:4(1cement 2M.sand 4 granite chips 20mm nominal size).(Labour Element)

Reinforced cemnt concrete 1:1:5:3(1cement 1.5 M. sand :3granite chips 20mm nominal size ) excluding cost of cenring shuttering and reinforcement all work up to plinth level. (Labour Element)

a) Foundation footings bases of column etc,and mass concrete.

Reinforced cement concret working (wall any thickness) including attached pilasters ,buttresses plinth and string course, fillets, column, pillars, piers ,abutments,post and struts etc..up to floor five level excluding cost of centering and shuttering finishing and reinforcement.1:1.5:3(1 cement 1.5 M. sand :3 granite chips 20 mm nominal size )(Labour Element)

Reinforced cement concrete work in beams ,suspended floors ,roofs,having slope up to 15 degree landing ,shelves chejjas,lintels ,bands,palin window sills,staircase and spiral staircase up to five level excluding cost of centering and shuttering finishing and reinforcemetn with 1:1.5:3(1cement 1.5 M.sand :3graded stone sggregate 20mm nominal size).(Labour Element)

Cold twisted steel reinforcement for RCC work including bending,binding and placing inposition complete.(Labour Element)

Centering and shuttering including strutting propping etc and removal of form work.(Full Cost)

a) Foundation footings bases of column etc,and mass concrete.

Centering and shuttering including strutting propping etc and removal of form work.(Full Cost)

Suspended floors,roofs,landings,balconies and acess plat form

Centering and shuttering including strutting propping etc and removal of form work.(Full Cost)

Lintels,beams,plinth beams,girders.bressumers and cantilevers

Centering and shuttering including strutting propping etc and removal of form work.(Full Cost)

Column,piller,piers,abutments,posts and struts

Centering and shuttering including strutting propping etc and removal of form work.(FC)

Stairs,(excluding landings) except spiral-staircase.

Cement concrete block (machine moulded) masonry in Foundation and plinth in CM 1:6 with blocks of size 40 cm x 20 cm x15 cm. (Labour Element)

Cement concrete block (machine moulded) masonry in Super structure above plinth level in CM 1 : 6 with blocks of size40 cmx 20cm x15 cm.(Labour Element)

Half brick work in superstrucute above plinth level up to floor five level in cement mortor 1:4(1 cement 4 M.sand).(Labour Element)

Providing wood work in frames of doos ,windows,clearstory windows and othe fames wrough ,framed and fixed in position complete Ist class karimaruth or equivalent.(Full Cost)

Providing and fixing 35mm thick panelled ,glazed or panelled and glazed shutters for doors, windows and clestory windows including anodised aluminium butt hinges with necessery screw.first class karimaruth or equivalent.Including 4mm thick float glass panes (Full Cost)

Providing and fixing Flush door shutters confirming to IS : 2202 (part.I) decorative type, core of block board construction frame offirst cladd hard wood and well matched first class teak 3 ply veneering with vertical grain so across bands and face veneers on both faces of shutters. 35mm thick including ISI marked Stainless steel butthinges with necessary screws(Full Cost)

Proviidng 40x3mm Iron hold fast 40cm long i/c fixing to frames 10mm dia bolts,nuts and wooden plugs and embedding in cement concrete blocks of size 30x10x15cm of mix 1:3:6(1cement 3M.sand 6stone aggregate 20mm nominal size).(Department shall provide cement , sand and stone aggregate.Contractor has to bring hold fast)

Providing and fixing curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P.brass screws and wooden plugs, etc., wherever necessary complete :.(Full Cost) a)20mm dia

Providing and fixing anodised Brass tower bolt(barrel type) with screws etc complete.(Full Cost)

a)250mmx10mm

b)150mmx10mm

Providing and fixing Brass Handle with necessry screws ect complete.a) 125 mm (Full Cost)

Providing and fixing Bright finished brass door latch with necessery screws.(Full Cost) a)300mmx 16mm x 5mm

Providing and fixing 100mm bras lock( best make of approved quality) for aluminium doors including necessary cutting and making good complete.(Full Cost)

Providing and fixing 100 mm Bright finished brass mortice latch and lock with 6 levers and a pair of lever handles with necessary screws..(Full Cost)

Providing and fixing Bright finished brass Hydraulic door closer with necessary fittings &screws ..(Full Cost)

Providing and fixing Bright finished brass door stoper with rubber cusion & necessary screws.(Full Cost)

Providing and fixing anodised Aluminium hooks and eyes anodised transparent or dyed to required color and shade with bolts , nuts and screws etc complete.(Full Cost) 200mm

Providing and fixing to existing door frame 24mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24mm and wall thickness 2mm± 0.2mm with in builted ging on both sides.The styles and rails mitred and joined at the corners by means of M.S. galvanised/ plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20mm and 1mm ± 0.1mm wall thickness.The lock rail made up of ’H’ section,a UPVC hollow section of size 100x24mm and2mm ± or 0.2mm wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S.‘U’cleats.The shutter frame filled with a UPVC multi - chambered single panel of size not less than 620 mm,having over all thickness of 20mm and 1mm ±0.1mm wall thickness.The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).(Full Cost)

Providing and fixing hand rail of approved size by welding etc.to steel ladder rail-ing ,balcony railing and stair case railing including applying a priming coat of approved steel primer.a)M.S Tube 96x48mm and 4.50mm thick. (Full Cost)

Providing and fixing stainless steel (Grade3 16)railing made of Hollow tubes ,channels,plates etc...including welding grinding ,buffing ,polishing and making good curvature (where required)and fitting the same with necessery stainless steel bolts etc.. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge (for payemnet purpose only weight of stainless steel members ahall be considered excluding fixing acessories such as nuts,bolts,fasteners etc...(Full Cost)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed withrawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gapsat junctions, attop, bottom and sides with required EPDM rubber / Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /panelling, C.P.brass / stainless steel screws, all complete as per architectural drawing sand the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately):For fixed portion..(Full Cost)

a)Anodised aluminium (anodised transparent or dyed to required shade according toIS:1868,Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed withrawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gapsat junctions, attop, bottom and sides with required EPDM rubber / Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /panelling, C.P.brass / stainless steel screws, all complete as per architectural drawing sand the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately):For fixed portion..(Full Cost).For shutters of doors, windows & ventilators including providing and fixing hinges /pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade1 TypeII in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass /stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.(Full Cost)

Prelaminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door,window,ventilator shutters and partitions etc.with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness

With float glass panes of 8 mm thickness

Providing and fixing aluminium tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screws etc.complete as per direction of Engineer-in-Charge.Anodized (AC 15 ) aluminium tubular handle bar.(Full cost)

Providing ans fixing glazing with 4mm thick clear transparent. Plane fibre glass erecting frame work made of power coated wooden grain finish aluminium rectangular section of size 100mm x 50 mm as per approved detail.( Frame work paid seperately).(Full cost)

Providing and laying vitrified floor tiles (premium quality)in different sizes (thickness to be specified by the manufacture) with water absorbtion less than 0.08% and confirming to IS:15622 of approved make in all coloures and shades,laid 20mm thick cement mortor 1:4 (1 cement :4 M.sand )including griouting the joints with white cement and matching pigments etc.complete(flooring) Department shall be provide cement and sand .Contractor has to be bring tiles size of 800x800mm.(Polished vitrified tiles-Khajariya/ Jhonson / Bell/Zeal top.(Full Cost)

Providing and laying vitrified wall tiles (premium quality)in different sizes (thickness to be specified by the manufacture) with water absorbtion less than 0.08% and confirming to IS:15622 of approved make in all coloures and shades, in skirting riser of steps,over 12mm thick bed cement mortor 1:3 (1 cement :3 M.sand )including griouting the joints with white cement and matching pigments etc.Department shall be provide cement and sand .Contractor has to be bring tiles size of 800x800mm.(Polished vitrified tiles-Khajariya/ Jhonson / Bell/Zeal top.(Full Cost)

Providing and fixing ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacture)of first quality confirming to IS: 15622 of approved make, in colours such as White, ivory, Grey, Fumered brown, laid on 20mm thick cement mortar 1:4(1cement,4metal sand)and joining with white cement and matching pigment etc... complete.(Matt/ smooth finish) Khajaria/Jhonon/Bell.Department shall provide cement and sand.Contractor has to bring tiles.(Full Cost)

Providing and fixing ceramic glazed wall tiles to confirming to IS:15622 (thickness to be specified by the manufacture) ,bottle ,green ,black of any size as approved by Engineer in charge in skirting ,risers of steos and dado over 12mm thick cment mortor 1:3(1cemnt 3M.sand )and joining wih grey cement slurry @3.3kg per sqm ,including pointing in white cement mixed with pigment and matching shade etc...complete.(Matt/ smooth finish) Khajaria/Jhonon/Bell.Department shall provide cement and sand.Contractor has to bring tiles.(Full Cost)

Chequerred precast cement concrete tiles 22mm thick in foot path & court yard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaninge tc. complete on 20mm thick bed of cement mortar 1:4 (1 cement : 4 metal sand sand). Dark shade using ordinary Cement. (Department shall be provide cement and sand . Contractor has to be bring tiles)

Providing and fixing 18mm thick gang saw cut mirror polished (pre moulded and pre polished) machine cut for kitchen plat forms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1cement : 4metal sand) with joints treated with white cement, mixed with matching pigment, epoxy to uchups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc.complete at all levels.(Department shall provide cement & sand. Contractor shall provide cement & Sand. Contractor has to bring Granite.

a) Raj Naggar plain white marble / Udaipur green marble/ Zebra black marble. Area of slab up to 0.50 Sqm.

a) Raj Naggar plain white marble / Udaipur green marble/ Zebra black marble. Area of slab over 0.50 Sqm.

6mm thick cement plaster to ceiling 1:3 (1 cement 3 Metal sand).(Labour Element)

12mm thick cement plaster 1:6. (1 cement 6 Metal sand).(Labour Element)

15mm thick cement plaster 1:6 (1 cement 6 Metal sand)on the rough side of single or half brick wall .(Labour Element)

French spirit polishing for a new work (two or more coats) including a coat of wood filler with ready mixed polish of approved brand and manufacture.(Berger/Nerolac/Asian Paint) (Full Cost)

Pinting wood work with Delux multi surface paint to give an even shade.Two or more coats applied on @0.90ltr/10sqm over uner coat of primer applied @0.75ltr/10sqm of approved manufacture. ( Berge / Shalimar / Asian paints)(Full Cost)

Pinting steel work with Delux multi surface paint to give an even shade.Two or more coats applied on @0.90ltr/10sqm over uner coat of primer applied @0.80ltr/10sqm of approved manufacture. ( Berge / Shalimar / Asian paints)(Full Cost)

Finishing with Delux multi surface paint system for interior and exteriors using primer as per manuifacture specifications two or more coats applied on walls @ 1.25 ltr/10 sqm over including priming coat of special primer appiled@ 0.75 ltr/10sqm.With Teflon coating (Berger / Nerolac / Asian paint)(Full Cost)

Providingand applying wall putty of2mm thickness over plastered surface to prapre the surface even and smooth complete.Birla white/ Berger Bison/ JK(Full Cost)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Pipes ,having thermal stebility for hot & cold water supply including all CPVC plain & brass threaded fittings,this included jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints as per direction of Engineer in charge .(External work.(Class I SDR 11).(Full Cost)

a)15mm nominal bore

b)32mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Pipes ,having thermal stebility for hot & cold water supply including all CPVC plain & brass threaded fittings,i/c fixing the pipes with clamps at1.00m spacing .This includes jointing of pipes and fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints as per direction of Engineer in charge .(Concealed work including cutting chases and making good the walls etc..)(Class I SDR 11).(Full Cost)

b)20 mm nominal bore

Providing and fixing C.P Brass bib cock of approved quality and manufacture complete.(Cera / Hindware / Parryware).(Full Cost)

a)15mm nominal bore

Providing and fixing C.P Brass stop cock of approved quality and manufacture complete.(Cera / Hindware / Parryware).(Full Cost)

a)15mm nominal bore

Providing and fixing C.P shower rose with 15to20mm inlet,150mm dia Telephonic shower of superior quality .(Full Cost)

Providing and fixing GM full way wheel valve of approved quality and manufacture complete. (Zoloto/leader/ Orient).(Full Cost) 32 mm nominal bore

Providing and fixing nominal guage PVC Pipe of approved quality comple with special flang compression type fittings including trenching and re filling etc. External work .110 mm nominal bore ( 6 kg/sqcms)(prince/ supreme/ Fenolex). (Full Cost)

Providing and placing on terrace at floor level Polythene water storage tank ISI:12701 marked with cover an suitable locking arrangement and making necessery holes for inlet,outlet an over flow pipe but without fittings and the base support for tank .a) 1000Litre capacity. Syntex/ Ocian/ Acqua Tech) . (Full Cost)

Providing and fixing white vitour china water closet pedestal pan(European) type WC pans with plastic seat lis and rubber buffers ,15white vitrous china low level flusing system of approved make with fittings and brackets 40mm flush bend ,20mm over flow pipe with complte includding cutting and making good the walls and floors where requred .White EWC pan with plastic seat and lid(Jaquar or equivalent. ( Cera Conventional type Model No.2008 / Hindware / Parryware).(Full Cost)

Providing anfd fixing white vitrous china wash basin with RS OR CI brackets painted white ,15mm C.P brass pillar tap and C.P bras chain and rubber plug 32mm C.P brass wsate of standard pattern 32mm dia metre and waste pipe complete including cutting and making good with walls and floors where required ( Cera Cognac type Model No.1011/ Hindware / Parryware).(Full Cost)

Providing and fiixng 600x450 mm mirror of superior glass (approved quality)complete with 6mm thick asbestos sheet ground fixed to wooden cleat with necessery screws and washers.(Cera. Model No.5567 Mirror size 600x300mm / Hindware / Parryware).(Full Cost)

Providing and fixing towel rail brackets fixed to wooden cleat with screws and washers .a)600x20mm C.P brass towel rail with brackets .600mm long towel rail brackets with total length of 645mm width 78mm and effective height of 88mm weighing not less than 190gms.(cera/ Parryware/ Neycer).(Full Cost)

Providing and fixing PTMT liquid soap container with C.P Brass lid and beraket fixed to wooden cleats with screws and washers .Viking /Hindware/ Parryware. (Full Cost)

Providing and laying PVC pipes grade "A" with stiff mixture of 1:3 (1cement :3 metal sand) including testing of joints etc .complete.(10 kg/cm2).(Full Cost)

a)110mm diametre

b)90mm diametre

Providing and fixing precast cement concrete 1:2:4(1cement : 2M.Sand :4graded stone aggregate 20mm nominal size)set in position with cement mortar 1:2(1cement: 2 fine sand) and finished smooth with 6mm thick cement plaster 1:3(1cement: 3fine sand)on exposed surfaces including centering and shuttering in baffle wall and slab .(Labour Element)

Brick work with modular bricks of class designation in foundation and plinth in C.M.1:6 (1Cement: 6 Metal sand).(Labour Element)

Cement concrete flooring1:2:4(1cement, 2metal sand, 4 granite chips) finished with floating coat of neat cement, including cement slurry,but excluding the cost of noising of steps etc…complete.(Labour Element)

a) 40mm thick with 20 mm nominal size stone aggregate

Neat cement Punning

Providing and laying cemnet concrete 1:5:10(1 cement :5 metal sand:10 graded stone aggregate 40mm nominal size) up to hauches of pipes including bed concrete a sper standard design. (Full cost). a)100 diameter

b)90mm diameter