11 KV Feeder Construction Work on Semi Turnkey Basis

Amount

Part-A (Supply of Material) 11 KV 3 Core Al. XLPE Insulated 3x185 mm sq. Cable

11KV XLPE Cable (3x185 sq.mm.) Heat Shrinkable Jointing kit Outdoor

M.S. Top Channel 100x50mm, 2240 mm with clamp, bolts, nuts and washers

M.S. Dropper Channel 100x50 mm, 2028 mm with clamp, bolts, nuts and washers

Earthing of pole by MS earthing rod of 20x2500 mm. and 6 SWG earthing wire etc.

11 KV Pin Insulator with G.I. Pin, nuts & washers

11KV 45 KN Disc fitting T&C type complete

Tee-off Channel 100x50x1300 mm with clamp, Nut & Bolt

Stey Complete (G.I. Stay Rod 16x1800mm, Stey Wire, Stey Clamp, Insulator, N/B etc.)

11KV V-Type Cross-arm (Angle 65x65x6mm)

F-bracket with bolts & nuts suitable for 11/13 Mtrs. Long ST Pole.

G.I. Pipe 6" dia. with Clamps

Holding clamps for MS Channel, T Channel & MS Angle with bolts & nuts

Bolt, Nuts & Washer

Part -B (Labour Work) Carriage of 9/11 Mtr Long ST Pole from 132 KV Store Center Mathura to dump site through the Kacha and Pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, T&P, carrier etc. required for proper completion of work.(Distance 00-70 Kms.)

Carriage of 13 Mtr Long ST Pole from 132 KV Store Center Mathura to dump site through the Kacha and Pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, T&P, carrier etc. required for proper completion of work.(Distance 00-70 Kms.)

Carriage of 11 KV XLPE Cable size 3x185 sq.mm. from 132 KV Store Center Mathura to site of work through the Kacha and Pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, T&P, carrier etc. required for proper completion of work.(Distance 00-70 Kms.)

Carriage of Line material i.e. conductor, G.I. wire, stay rod, disc insulator, cross arm, Angle channel and other required material from Store Center at 132 KV substation Mathura to the site of work including loading and unloading of material at both ends.

Erection of single pole structure 11 Mtrs on ST Pole by digging of pits fitting of all relevant accessories as per RESPO norms.

Erection of Double pole/Section Pole structure 11 Mtrs on ST Pole by digging of pits fitting of all relevant accessories as per RESPO norms including grouting of pole in ratio 1:4:8 cement, sand and brick ballast as per standard norms, including cost of all grouting material.

Erection of single pole structure 13 Mtrs on ST Pole by digging of pits fitting of all relevant accessories as per RESPO norms.

Construction of Section pole/“T” pole for H.T. line on the erected pole/Existing Tower with the help of gas cutter as per RESPO manual and as per direction of supervising engineer. It including the cost of all labour, gas cutter, T&P, etc. required for proper completion of work.

Installation of stay set with grouting and nuzzling etc. as per RESPO drawing along with all routine material to be used for such works.

Earthing of poles by fixing earthing rods and binding with earth wire as per standard norms including cost of labour T&P and required material for such work.

Laying, sagging stringing and binding of ACSR Dog Conductor on the erected PCC pole/STP including jumpering as per RESPO manual.

Chopping of Tree branches to Clear the route properly.

Straightening of 11 KV Line tilted pole structure on ST Pole at various places by straightening of pole including the cost of labour ,T&P charges required for proper completion of work (inside/outside village)

Re-sagging of loose H.T/L.T line as per direction of supervising engineer. It includes the cost of labour, T&P etc required for proper completion of work.(work will be done inside and outside of village)

Digging of trench for laying of 11 KV cable size 3x185 sqmm in to the trench as per supervising engineer.

Laying of 11 KV XLPE Cable size 3x185 sq.mm. in the trench as per RESPO manual.

Re-dressing of trench after laying of cable properly by send/earth work as per norms and direction of supervising engineer.

Fixing of 11 KV Cable Jointing Kit 3x120/3x185 sq.mm outdoor/indoor including removal of insulation, semi-conductor of the cable end and filling of cable box complete work as per direction of supervising engineer.

Grouting of PCC/ST pole in ratio 1:4:8 cement, sand and brick ballast as per standard norms, including cost of all grouting material.

Safe loading of 11KV V.C.B. in store center at 132 KV S/s Mathura with the help of Crain/Hydra machine including all accessories complete.

Carriage of the new 11KV V.C.B. from store center at 132KV S/s Mathura to 33/11 KV S/s Side-B as per direction of supervising engineer. Approximate distance 30 Km.

Safe unloading of 11KV V.C.B. at 33/11 KV S/s Side-B with the help of crain/hydra machine including all accessories complete as per direction of supervising engineer.

Very carefully shifting of 11KV V.C.B. panel from outside of control room into the control room as per direction of supervising engineer.

Installation of 11KV V.C.B. in control room at 33/11KV S/s Side-B and making all connection ie. Bus bar etc. as per direction of supervising engineer.

Earthing of V.C.B. panel by the chemical earthing as per direction of supervising engineer.

Vivek Electricals

Gowri Associates

M/s. Siddhi Vinayak Enterprises, Agra

M/S PRAVEEN ELECTRIC COMPANY SALES