SPECIAL REPAIRS TO HEAT TREATMENT SHOP (FOUNDRY COMPLEX) OF BUILDING NO. P-68 IN TECH AREA AT CVRDE, AVADI

Amount

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 75mm thick Cement concrete 1:4:8 type D2, (40mm graded aggregate) as in sub base complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded aggregate laid to slope 40mm thick as levelling course complete all as specified and directed.

M &L Screed bed or bedding layer of cement mortar 1:6 of 15mm thick for laying floor finishes complete all as specified and directed.

M&L Non Skid joint free colour ceramic tiles 8-10 mm thick (squares/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Non Skid joint free colour ceramic tiles 8 -10 mm thick (squares/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surfaces/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 as in backing coat on fair faces of brick work or concrete surfaces complete all as specified and directed.

Removing the existing deteriorated reinforcement and supply and placing of new cold twisted TMT bars including cutting, bending and straightening and placing in position complete in all levels and if necessary welding the new bars with the existing. Rods by over lapping with all lead and lift etc. complete all as specified and as directed by the Engineer in charge. (All labour, materials, tools and plants are to be supplied by the contractor only at his own cost)

Application of NITOZINC PRIMER: Removing the loose particles rust / mill scale deposits completely duly cleaning it with wire brush / crush sheet etc. and removing the dust etc. complete over the old concrete surface and supply of zinc rich epoxy primer NITOZINC PRIMER and mixing mechanically until it is homogenous and applying the same as one rich coat of reinforcement complete with all dead and lift etc. complete all as specified and as directed by the Engineer in charge. (All labour, materials, tools and plants are to be supplied by the contractor only at his own cost).

Repair to slab & beam using structural grade repair mortar:- After surface preparation the substrate should be thoroughly soaked with water (any excess being removed) prior to applying one coat of Nitobond SBR and scrubbing it well into the surface. Renderoc S2 can be applied as soon as the Nitobond AR become tacky. Place about 2.75 litres of drinking quality water in the mixer and, add the supplied liquid polymer part and mix with the machine in operation, add Renderoc S2 powder and mix for 2 to 3 minutes Apply the mixed Renderoc S2 to the prepared substrate with a gloved hand or trowel. First work a mini layer of the mortar on to the layer. Thoroughly compact the mortar on to primed substrate. Where thicker sections are required, the surface of the intermediate layer should be scratch keyed and primed with Nitobond AR. Repriming with Nitobond AR and further application of Renderoc S2 may proceed as soon as this layer has set. Renderoc S2 is finished by striking off with a straight edge and closing with a steel float. Applying one coat of acrylic curing membrane NITOBOND AR mixed with water in the ratio 1:1 with all lead and lift etc., complete and as directed by the Engineer in charge. (All labour, materials, tools are to be supplied by the contractor only at his own cost). Avg. Thickness 30mm.

Preparation of new plastered surface of ceiling and apply three coat of white wash complete all as specified and directed.

Taking down cement plaster on brick walls including racking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Rendering 15mm thick in fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth with out using extra cement but using water proofing compound complete all as specified and directed.

Rendering 10mm thick in fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth with out using extra cement complete all as specified and directed.

M&L for preparation of new plastered wall surface and applying two coats of weather coat paint over a coat of primer and 2mm thick wall putty complete all as specified and directed.

M&L for preparation of new plastered wall surface and applying two coats of distemper oil emulsion over a coat of primer and 2mm thick wall putty complete all as specified and directed.

Supply only integral water proofing compound

Taking down chowkats with shutters (without taking off shutters from the frames) n.exc area 1.50 Sqm complete all as specified and directed.

S&F anodised alumnium powder coated frame for doors and windows with one or more rebates including joining cleats for fixing etc complete all as specified and directed.

S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars and aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.), aluminium anodised tower bolt 150 mm long( 1 no.) aluminium handle (1no.) in each shutter complete all as specified including powder coating of any colour(Thickness or powder coating not less than 50 micron) complete all as specified and directed.

S&F 10mm wide 6mm thick powder coated Anodised aluminium grill(anodised transparent or dyed to required shade according to IS-1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws@200 mm centre to centre,including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening,all complete as per requirement and direction of engineer in charge.

S&F Sheet glass 4mm thick tinted including glazing in square n. exe 0.5sqm in each pane complete all as specified and directed.

S&F Sheet glass 5.5mm thick tinted including glazing in square exe 0.5sqm in each pane complete all as specified and directed.

Dismantling of Asbestos cement sheet in roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Prepainted galvalume aluminium zinc coated sheet of trapezoidal profile in roof covering/ cladding. Sheeting shall be provided with PUF panels with 50mm thick puff (50mm polyurethane foam of 40 +/-2 Kg/Cum density) sandwiched between top and bottom 0.5mm TCT colour coated corrugated sheets with minimum yield strength 550 N/ Sqmm. The sheet shall have a hot dipped metallic Aluminium-Zinc alloy coating of 55% Aluminium 43.5% Zinc & 1.5% Silicon with total mass coating of 150 g/Sqm on both sides as Galvalume/Zincalume AZ 150 as per AS 1397: 2007/IS 15961:2012. The roof panel shall be trapezoidal profile, 930-10230mm effective width, 28-38mm crest depth at 250-350 c/c, manufactured out of 0.50mm TCT, Hi Tensile Galvalume/ Zincalume steel pre painted with super durable polyster paint system of approved colour shade suitable for external exposure condition. The sheet shall have suitable square fluting or shall have 2-3 Nos stiffening ribs in profile pan for better strength and effective water shedding. The sheet shall have special male/ female ends with full return legs on side laps for purlin support and anti capillary groove to avoid any seepage of water through lateral overlap. Profile of the sheet shall be approved by AGE (I). All laps of roof panels shall lbe sealed with a contnuous ribbon of tape sealer. Silicon rubber sealent of approved make shall be applied a all end laps as per manufacturer's recommendation and approved by Engineer-in-Charge. The sheet shall be fastened with min 40 micron zinc coated or min 20 micron Zinc-Tin alloy coated, hexagonal head, self-drilling screw as per AS 3566-2002 class 3 fasteners of approved make with EDPM washer on each crest of sheets for connecting with purlin and all as per manufacturers instruction complete all as specified and directed.Make : Jindal Mectec Pvt Ltd./ Metecno India Pvt Ltd./ E-Pack Polymers Pvt Ltd.NOTE: Overlap shall be as specified by manufacturer.

S&F Roof trusses (framed), Fe 410-W(Gde 250) Quality trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

Preparation of new steel surface exe.10cm girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F wired glass 6.4 mm thick and glazing with oil putty in square for north light area exceeding 1.0 Sqm and not exceeding 1.50 Sqm complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar (but not backing) complete all as specified and directed.

M&L non skid joint free coloured ceramic tiles 7 to 8mm thick area of each tiles (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc., complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surfaces 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, etc., complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm complete all as specified and directed.

S&F in opening solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed by Engineer-in-Charge.

S&F Factory made solid PVC Moulded Door shutter 28 to 30mm thick(stiled) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face with particle board core complete all as specified and directed.

S&F 200mm Aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F Aluminium handle cast type anodized of size 150mm long complete all as specified and directed.

S&F aluminium Butt hinges,100 mm, medium weight complete all as specified and directed.

S&F in repairs vitreous china squatting pan orissa pattern of size 580x440mm white with integral foot rests including connecting to trap and to flushing pipe anti syphonage pipe etc. complete including making good to floor including trap set including complete concrete. flush pipe to squatt pattern closet complete all as specified and directed.

S&F in repairs 10 litres PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 15mm CP stop cock and pic connection 600mm long complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolt, sheet cover complete all as specified and as directed.

S&F in repairs 15mm dia Pillar taps, cast copper alloy with capstan heads, chromium platted screwed down high pressure with or without lettered HOT or cold with long screwed shanks and fly nuts, Screwed for iron pipe and fixed for 15mm bore dia (Fancy type), complete all as specified and directed.

S&F in repairs 15mm dia brass chromium plated bib cock fancy type screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore dia complete all as specified and directed.

S&F in repairs stop valves (angle valve)cast copper alloy screwed down high pressure with butter fly handle size 15mm dia bore(fancy type) complete all as specified and directed.

S&F 75mm dia PVC (SWR) multi floor trap plain with grating lincluding jointing with solvent cement complete all as specified and directed.

Taking up or down steel tubing and connections 15mm dia complete all as specified and directed.

All as described in serial item No. 47 above, but 20mm dia

S&F 15mm bore medium grade GI tubing with all fitting and fixed to wall and celing or laid in floors complete all as specified and directed.

S&F 20mm bore medium grade GI tubing with all fitting and fixed to wall and celing or laid in floors complete all as specified and directed.

S&F in repairs brass cromium plated tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type complete including providing and fixing plugs, bedding urinal against wall in CM (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing autometic flushing cistern with brackets. flush pipe with grating union for discharge pipe(Exclusive of fixing supply pipe to flushing cistern trap and waste pipe) complete all as specified and directed.

M&L granite jet black colourt 20mm thick,factory polished fixed to RCC slab with neat cement slurry including cutting to shape,grinding,polishing and bulnosing etc all as directed incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M & L Precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in cover slabs, shelves of any thickness, size or shape including necessary form work, finished concrete surfaces fair and even complete all as specified and as directed.

M&L TMT steel bars ,6 to 8 mm dia and over cut to length and bent to shape as required including cranking,hooking ends and binding with and including MS wire(annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

S & F in repairs vitreous china wash hand basin white/coloured flat back size 550 x 400mm including 32mm waste coupling, waste pipe and procelain stopper brackets etc complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F Health faucet chromium platted including flexible pipe, Screwed for iron pipe and fixed for 15mm bore dia(Fancy type) complete all as specified and directed.

S&F vitreous china urinal partition, white, of size 310 x 200 mm complete all as specified and directed.

Demolition and breaking up 150 mm dia drain pipes set in cement morter complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any radius complete all as specified and directed.

Complete removal of existing treatment of any type on the wall and applying two coats of weather coat paint over a coat of primerover a 2mm thick wall putty complete all as specified and directed.

Complete removal of exisiting treatment of wall and applying two coat of oil emulsion distemper over a coat of primer over a 2mm thick wall putty complete all as specified and directed.

Preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

Preparation of old steel surfaces exe.10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L 75mm thick Cement concrete 1:3:6 typeC-2, (40mm graded aggregate) including finishing the surfaces even and smooth without using extra cement as in plinth protection complete all as specified and directed.

S&F in repairs 1.25mm thick Steel rolling shutters, gear operated type with ball bearing, including mild steel high tension spring of required length, mild steel tubes of 32 mm to 50 mm dia,cleat,anchoring rod,hasp,staple,stays and one shop coat of primer; erected in position complete including top cover of 1.25 mm thick steel as directed with gear operated type with bevel gear box and crank handle with two safety lever lock and keys for each rolling shutter, complete all as specified and directed.

M&L for fabrication, testing and commissioning to electrical system LT panel CPRI approved (Indoor type) suitable size, factory made, compartmentalised design, back door hinged type & openable fabricated out of 2mm thick CRCA steel sheet, weather, dust and vermin proof suitable spaced totally enclosed in chamber, earthing arangement locking arrangement with one lock with duplicate key duly painted with powder coated paint having danger notice boards and earthing terminal on both both sides and provding the following item including connection all incoming and outgoing cables using suitable size spreader terminals lugs and glands control wiring complete including taking down old LT Panel in all respect all as specified & directed comprising of following items:- (i) 4 Nos Copper bus bars of high conducitivity 3 Nos for phase (RYB) rating 1200 Amp, 01 No for neutral rating 600 Amp and out going bus bars mounted on DMC support wth heat shrink sleeve-01 set (ii) ACB 800 Amp 50 KA breaking capacity 4 pole with microprocessor release (incoming) - -01 Nos (iii) MCCB 4P 320A, 415 volts , 36 KA fixed thermal magnetic release with handle type-1Nos.(out going) (iv) MCCB 4P 250A- 415 volts , 25 KA fixed thermal magnetic r elease with handle type - 3 Nos (out going) (v) MCCB 4P 40 A -415 volts , 16 KA fixed thermal magnetic release handle type -1 Nos (Out going) (vi) Multi function meter , three phase digital type with parameters like voltage amphere, frequency and Main suitable CTs for 3 Phase (vii) Indication lamp (RYB) LED type with toggle swtiches -01 set of three

M&L for fabrication, testing and commissioning to electrical system LT panel CPRI approved (Indoor type) suitable size, factory made, compartmentalised design, back door hinged type & openable fabricated out of 2mm thick CRCA steel sheet, weather, dust and vermin proof suitable spaced totally enclosed in chamber, earthing arangement locking arrangement with one lock with duplicate key duly painted with powder coated paint having denger notice boards and earthing terminal on both both sides and provding the following item incl connection all incoming and outgoing cables using suitables size spreader terminals lugs and glands control wiring complete including taking down old LT Panel in all respect all as specified & directed comprising of following items:- (i) 4 Nos Copper bus bars of high conducitivity 3 Nos for phase (RYB) rating 300 Amp and 01 No for neutral rating 150 Amp and out going bus bars mounted on DMC support wth heat shrink sleeve-01 set (ii) MCCB 4P 200A, 415 volts , 25KA fixed thermal magnetic release with handle type- 1Nos.(Incoming ) (iii) MCCB 4P 100A- 415 volts , 16 KA fixed thermal magnetic release with handle type- 2 Nos (out going) (iv) MCCB 4P 63 A -415 volts , 16 KA fixed thermal magnetic release with handle type -1Nos (Out going) (v) Multi function meter , three phase digital type with parameters like voltage ampere, frequency and Main suitable CTs for 3 Phase (vi) Indication lamp (RYB) LED type with toggle swtiches -01 set of three

Supply, laying and testing cable XLPE Insulated PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 sq mm 3.5 core laid in existing duct and including taking down unserviceable LT cable complete all as specifed and directed.

Supply, laying and testing cable XLPE Insulated, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 4 core laid in existing duct and including taking down unserviceable LT cable complete all as specifed and directed.

S&F fix in repair Earthing complete with galvanised steel earth plate electrode 60x60cm x 6.0mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to and including using of 32 x 6 GI strip as earthing lead by means of bolts, nuts, check nuts and washers of galvanised steel , connected to earthing test point, all as specified & indicated, including testing on completion including earth work and excavation in any type of soil, PCC 1:3:6 type C1, earthing chamber, precast RCC slab 50mm thick in cement concrete 1:2:4 type B1 reinforced with welded steel wire fabric weight hot less than 4 Kg/Sqm, funnel with GI watering pipe of 20mm bore, medium grade wire mesh and lugs, GI protection pipe of 40mm bore light grade upto 7.50 mtr long test point etc all as specified and directed.

Supply and fixing in repairs/ replacement LED street light fitting 35 Watts,100 lumens/watts efficiency 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repairs/ replacement of SMC loop junction box of size not less than 140x140x95 size with connector, MCB SP 6A complete all as specifed and directed.

Taking down unserviceable chequered plates and S & F ( chequered) plate Fe 410-W(Gde-E-250 Quality-A)Square cut or notched (Ordinary and counter sunk) for covering polates and base plates, cladding , etc forming holes, with any attachement angle or other section with gusset plates, rails, braces with ornamental and intricate design , drilled for fixing of steel sheeting or other covering with handles, running rails and guides, hanging including fastening and fixing complete all as specified and directed (Cable duct chequered plate)

Taking down aluminium point wiring (light, fan, socket or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. complete all as specified and as directed.

M&L for Point wiring with 1100Volts grade, single core, PVC insulated FRLS cable multi-stranded copper conductor of size 1.5 sqmm nominal area for phase and neutral, drawn through and including ISI marked non metallic pvc conduit 20mm dia with all necessary fittings and accessories for concealed wiring incl cutting chases in walls/ ceiling and making good disturbed surfaces with one run of single core cable1.5sqmm green colour in continues earthing wire connected to common earth dolly including PVC junction / mounting boxes on / in the wall / ceiling for modular switches/ switch socket combination/ fan regulators etc complete for the following :- One light point controlled by one switch complete

All as described in serial item No. 82 above, but for One 5A Socket on Independent board

All as per Serial Item No. 82 above but for one 15 Amps socket, with 2.5 Sq.mm single core PVC insulated, FRLS cable, multi-stranded, copper conductor and including 2.5 Sq.mm single core PVC insulated, FRLS cable, multi-stranded, copper conductor as earth continuity conductor and connecting to earth dollycomplete all as specified and as directed.

S&F Modular switch 1 way 6A, 230 Volts, 50 HZ, 1 module complete all as specified and directed.

S&F Modular socket 6A, 230 Volts, 50 HZ, 2 module complete all as specified and directed.

S&F Modular socket 6/16A combination, 230 Volts, 50 HZ, 2 module complete all as specified and directed.

S&F Modular type Fan step regulator, 120W, 230 Volts, 50 HZ, 2 module complete all as specified and directed.

M&L for sub main wiring complete with 2 runs of 1.5 sqmm single core PVC insulated and unsheathed FRLS cable with copper conductor multistranded 1100 volts grade including steel conduit with accessories fixing on surface/wall/floor/truss etc including one run 1.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly incl taking down unserviceable aluminium wiring of any size complete all as specified and directed.NOTE: ONE RUN OF EARTH CONTINUITY CONDUCTOR,TWO RUN OF COPPER CONDUCTOR AND ONE RUN OF STEEL CONDUIT TOGETHER TAKEN AS ONE LENGTH FOR MEASURING UNIT LENGTH.

S&F Switch piano, flush type, single pole, one way, 5 Amps, 230 v, 50 HZ complete all as specified and directed.

M&L for sub main wiring with 2 runs of 2.5 sqmm single core PVC insulated and unsheathed FRLS cable with copper conductor multistranded 1100 volts grade including steel conduit with accessories fixing on surface/wall/floor/truss etc including one run 2.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly incl taking down unserviceable aluminium wiring of any size complete all as specified and directed.NOTE: ONE RUN OF EARTH CONTINUITY CONDUCTOR,TWO RUN OF COPPER CONDUCTOR AND ONE RUN OF STEEL CONDUIT TOGETHER TAKEN AS ONE LENGTH FOR MEASURING UNIT LENGTH.

M&L for sub main wiring with 4 runs of 2.5 sqmm single core PVC insulated and unsheathed FRLS cable with copper conductor multistranded 1100 volts grade including steel conduit with accessories fixing on surface/wall/floor/truss etc including one run 2.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly incl taking down unserviceable aluminium wiring of any size complete all as specified and directed.NOTE: ONE RUN OF EARTH CONTINUITY CONDUCTOR,FOUR RUN OF COPPER CONDUCTOR AND ONE RUN OF STEEL CONDUIT TOGETHER TAKEN AS ONE LENGTH FOR MEASURING UNIT LENGTH.

M&L for Socket outlet 2 in1, 5/15A, Piano type, 230 Volts, 50 HZ complete all as specified and directed.

M&L for Switch 15A, Piano type, 230 Volts, 50 HZ complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 100 lumens/watts, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in repair energy efficient high bay light fitting of 120 Watt 100 lumens/watts including No. of LEDs in fittings as per manufacturer’s instructions for lighting of 120 watt ,epoxy powder coated pressure die cast aluminium housing to act as heat sink for efficient dissipation of heat and toughened glass with IP 66 degree of protection, system luminous efficiency more than 100 lumens / watt individual LED's should have lenses for better throw across and along road, PF>0.9 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 10 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including making electrical connection for cable connection complete all as specified and directed by Engineer in charge.

M&L for DOL starter suitable415V, 1-5A rating complete all as specified and directed.

M&L for TPN DB 6Way double door horizontal type, 415 volts, IP 43 including MCB TPN 63A as Incomer, MCB DP 32A-1No, MCB 3P 25A-4Nos as outgoing complete all as specified and directed.

S&F modular switch 16A 230V 50 Hz 1 module complete all as specified and directed.

M&L for TPN DB 4Way double door horizontal type, 415 Volt, 50HZ, IP 43 with MCB 4P 25A as Incomer , MCB SP 6A-1Nos, MCB 16A-10Nos as outgoing complete all as specified and directed.

M&L for SPN DB 12Way double door 415 Volt, 50HZ, IP 43 including MCB DP 32A as Incomer, MCB SP 6A-4Nos, MCB SP 16A - 4Nos complete all as specified and directed.

M&L for taking down unserviceable High bay MH 150W fittings complete all as specifed and directed.

Supply & fix single pointed air termination aluminium rod 12mm dia, 300 mm long including taking down unservieable air termination complete all as specified and directed.

Supply and fix Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including taking down unserviceable aluminium strip complete all as specified and directed.

Supply and fix GI strip 32mm x 6mm buried in ground and including taking down unserviceable GI Strip complete all as specified and directed.

Supply and fixing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

thirukumaran developers

SAMYDOSS CONSTRUCTIONS