ADDITION / ALTERATION AND SPECIAL REPAIRS TO BUILDING (P-261) AT ECHS POLYCLINIC MUMBAI UPNAGAR (POWAI) UNDER GE (NW) BHANDUP

Amount

Demolition of brick /cement (unreinforced) from existing Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work. Complete all as specfied and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope including making rounded or chamfered on edges mixed with WPC @2% by weight of cement, Complete all as specfied and directed by Engineer-in-Charge. Note: WPC shall be measured and paid separately as supply only.

M&L Rendering 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces with WPC in the proportion as recommended by the manufacture finished even and smooth,over top of roof surface Complete all as specfied and directed by Engineer-in-Charge.

M&L for supply and application of 7 layer SHR waterproofing coating system on leaking concrete surfaces by thorough surface preparation, opening of cracks followed by one absorption coat of thermacool wp51, nano tech modified, uv resistant electroplast clear coat having min 50% solids,filling of crack, then overcoating with sandwitch coat of electromeric (thermacool wp51 + cement) waterproofing layer weigh 80 gsm non woven fibre mesh, application of 3 rd coat of elastomeric waterproofing laye having +450% elogation, tensile strength min 2.2 with two cats of thermacool 0.3c pure acrylic based, uv resistant mpa and then top-coated non-yellowing bio- organism resistant. Complete all as specfied and directed by Engineer-in-Charge.

Supply only Integral waterproofing compound, Complete all as specfied and directed by Engineer-in-Charge.

Taking down the cement plaster or lime plaster on walls ceiling of any descrioption from concrete or brick wall. Complete all as specfied and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in cement mortar (1:6) on the surface of walls including finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Change.

M&L for rendering 5mm thick in cement mortar (1:3) on the surface of ceiling finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Change.

M&L Sand faced cement plaster 20 mm thick in two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt. Ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 12 mm thick and finishing coat of 8 mm thick final rendering,including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing etc. Complete all as specfied and directed by Engineer-in-Charge. Note: The rate inclusive of scaffolding.

M&L for 3mm thick wall care putty on new or old surface of walls/ceiling finished even and smooth Complete all as specfied and directed by Engineer-in-Charge.

M&L for preperation of new external wall plastered surface and applying one coat of primeseal prime of M/s Dr fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating under torch dry collection and subsequently applying two coat of water proofing decorative elastomeric coating system raincoat of M/s Dr fixit with DFT 100 microns or shalicry 215 of M/s STP Ltd or chemstic PDE 600 elastomeric coating including necessary scaffolding etc complete all as per manufacturer instructions and all specified & directed

M&L for preperation of new plastered surface of wall and applying two coats of oil bound distemper with roller over one coat of chalk whitening primer Complete all as specfied and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment of walls by broming down or steel wire brushing,scrapping down smoke soot,mould,moss and efflorescent salts and trading oil and greasy spots including washing down with water and thereafter applying with roller Two coat of oil bound distemper complete all as per manufaturer's instructions Complete all as specfied and directed by Engineer-in-Charge.

M&L for preparation new plastered surfaces of ceiling and applying two coats of distemper over a coat of primer Complete all as specfied and directed by Engineer-in-Charge.

M & L for preparation of old decorated surfaces of ceiling by brooming down or steel wire brushing scrapping down smoke, soot ,moulds, moss and efflorecent salts and treating oil and gresy spots and thereafter applying one coat of oil bound distemper with roller Complete all as specfied and directed by Engineer-in-Charge.

M&L for complete remoal of existing treatment from the surface of existing walls,parapet walls,chajjas etc by bromming down or wire brushing, scrapping down smoke soot,moulds, moss and efflorescent salts and trading oil and geasy including washing dowm with water etc, preparing the surface and there after applying one coat of primeseal primer of M/s Dr fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating under torch dry collection and subsequently applying two coat of water proofing decorative elastomeric coating system raincoat of M/s Dr fixit with DFT 100 microns or shalicry 215 of M/s STP Ltd or chemstic PDE 600 elastomeric coating including necessary scaffolding etc complete all as per manufacturer's instructions. Complete all as specfied and directed by Engineer-in-Charge.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness(below or above ground level) including removing debris outside MD land, Complete all as specfied and directed by Engineer-in-Charge.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection surface finished even & smooth without using extra cement including provision of 10mm joints duly filled with fine sand and bitumen in the ratio of 3:1 complete all as spcified and directed.

M&L providing cement concrete type B0, 1:2:4 (12.5mm graded aggregate) 25mm thick as in flooring Complete all as specfied and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specfied and directed by Engineer-in-Charge.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 Complete all as specfied and directed by Engineer-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match alongwith rendering 10mm thick with CM 1:4 on fair faces of brick work or concrete surfaces Complete all as specfied and directed by Engineer-in-Charge.

M&L for vitrified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finished Complete all as specfied and directed by Engineer-in-Charge.

M&L for vitrified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in walls skirting etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles. Complete all as specfied and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings Complete all as specfied and directed by Engineer-in-Charge.

M&L for Sand filling under floors or in foundation including watering and consolidation Complete all as specfied and directed by Engineer-in-Charge.

M&L for Machine pressed (LAQUER FINISH) cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80 mm thickness, M-40 Grade, machine pressed of pattern and colour as approved by GE. Complete all as specfied and directed by Engineer-in-Charge.

S&F in repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern) etc Complete all as specfied and directed by Engineer-in-Charge.

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and including 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S&F of Cast iron floor trap 100mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate and taking out existing unserviable traps by hacking out concrete joints and making good of surface Complete all as specfied and directed by Engineer-in-Charge.

S&F of 32mm dia low density polyet?hylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc, Complete all as specfied and directed by Engineer-in-Charge.

S&F in repairs flushing cristern, 10 liters capacity,PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets,flush pipe of polyethylene of low or high density or PVC, 32mm dia Complete all as specfied and directed by Engineer-in-Charge.

S&F of 15mm bore brass CP Stop cock,make ESSCO Cat no MQT 513 or equivalent as approved by the GE, Complete all as specfied and directed by Engineer-in-Charge.

S&F of 15mm bore brass CP Bib tap,make ESSCO Cat no MQT 511 or equivalent as approved by the GE, Complete all as specfied and directed by Engineer-in-Charge.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, Complete all as specfied and directed by Engineer-in-Charge.

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed Complete all as specfied and directed by Engineer-in-Charge.

S&F in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc. Complete all as specfied and directed by Engineer-in-Charge.

S&F in repair SS soap dish. complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP Health faucet with 1 mtr tube & hook Complete all as specfied and directed by Engineer-in-Charge.

S&F in repair CP corner glass with brass bracket screws etc Complete all as specfied and directed by Engineer-in-Charge.

S&F in repair brass chromium plated towel rail 20mm dia 'D' type 600mm long between flanges with and including chromium plated brass screws etc Complete all as specfied and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm Complete all as specfied and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm Complete all as specfied and directed by Engineer-in-Charge.

S&F 15mm bore U-PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings Complete all as specfied and directed by Engineer-in-Charge.

All as per item No 45 above but 20 mm bore. Complete all as specfied and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc Complete all as specfied and directed by Engineer-in-Charge.

M&L for rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails, staging for water tank and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to FE 290 Gde 165 Complete all as specfied and directed by Engineer-in-Charge.

M&L two coats of synthetic enamel paint over one coat of red oxide primer on new steel surface after necessary preparaton of surface over 10 cm in width or girth Complete all as specfied and directed by Engineer-in-Charge.

M&L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over and including 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specfied and directed by Engineer-in-Charge.

M&L for taking down carefully copper/aluminium point wiring (light, fan socket or power) complete such as switches, ceiling rose pendents ,regulators, sockets etc removing materials to store for keeping in safe custody or for taking credit ( credit for above item should be made as per condition seperately) and making good disturbed surfaces of walls , floors etc.

M&L for taking down and refixing carefully old unserviceable Ceiling fan/exhaust fan. Complete all as specfied and directed by Engineer-in-Charge.

M&L for taking down old unserviceable MCB DBs including MCBs Complete all as specfied and directed by Engineer-in-Charge.

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn E36wiring with PVC counduit in wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly Complete all as specfied and directed by Engineer-in-Charge. (a) One light point controlled by one switch Note: (i) Modular Metal Flush Box, cover plate and frame shall be measured and paid separately. (ii) Rates for cutting chasing and making good are inclusive in quoted price.

All as per item No 54 but for one fan/ exhaust fan one fan/exhaust fan point controlled by one switch. Complete all as specfied and directed by Engineer-in-Charge.

All as per item No 54 but for one 3 pin socket point 5A controlled by switch on same board. Complete all as specfied and directed by Engineer-in-Charge.

All as per item No 54 but for one 3 pin socket point 5A controlled by switch on independent board. Complete all as specfied and directed by Engineer-in-Charge.

All as per item No 54 but for one bell point controlled by one switch. Complete all as specfied and directed by Engineer-in-Charge.

M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductor drawn in concealed conduit wiring with PVC counduit in wall, ceiling etc with all accessories, fittings in wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, also including 2.5 Sqmm, PVC insulated, FRLS, unsheathed, multistranded, copper conductor 1100 Volts grade, green color, continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent Complete all as specfied and directed by Engineer-in-Charge. Note: Modular Metal Flush Box, cover plate and frame shall be measured and paid separately.

Supply and Fix Bell, AC, 230 Volts, single pole, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix modular bell push, 6 Amp, 1 module, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix modular switch, 1 way, 6 Amp ,1 module, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix modular switch, 1 way ,16 Amp, 1 module, Complete all as specfied and directed by Engineer-in-Charge.

S&F ceiling rose three terminal, 230 Volts, PVC / Polycarbonate body, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix Modular socket outlet, 6 Amps, 2/3 pin combined 2 module, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix Modular socket outlet 6A/16 Amps, 2/3 pin combined 2 module, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix modular fan step regulator, 120W, 2 module, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix concealed modular GI coating metal flush box with and including matching modular cover plate with frame, 1 Modules, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix concealed modular GI coating metal flush box with and including matching modular cover plate with frame, 3/4 Modules,Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix concealed modular GI coating metal flush box with and including matching modular cover plate with frame, 6 Modules, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix concealed modular GI coating metal flush box with and including matching modular cover plate with frame, 8 Modules, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fix concealed modular GI coating square metal flush box with and including matching modular cover plate with frame, 12 Modules, complete all as specified and directed

Supply & Fix in repair of heavy duty metallic Exhaust fan of sweep 300 mm sweep , 900 RPM Complete all as specfied and directed by Engineer-in-Charge.

S&F LED Batten, integrated sleek aluminium extruded LED channel with acrylic cover, with and including 20 Watt white light and driver, prewired, provision of 0.5 Sqmm 3 core flexible copper conductor wire for connecting from ceiling rose, Complete all as specfied and directed by Engineer-in-Charge.

S & F MCB protected socket modular AC box, 3 module with sheet steel enclosure with 20 Amp MCB including taking down Complete all as specfied and directed by Engineer-in-Charge.

S & F MCB DB, 08 way, SPN, double door, 240 Volts, fixed concealed/ surfaces on the wall, making all connections, Complete all as specfied and directed by Engineer-in-Charge.

S & F MCB DB, 12 way, SPN, double door, 240 Volts, fixed concealed/ surfaces on the wall, making all connections, Complete all as specfied and directed by Engineer-in-Charge.

S & F triple pole and neutral MCB DB, 4 way, double door, 240 Volts, fixed concealed/ surfaces on the wall, making all connections, Complete all as specfied and directed by Engineer-in-Charge.

Supply and fixing MCB, Three pole, 40Amp, 415V 10KA 'C' curve type Complete all as specfied and directed by Engineer-in-Charge.

Supply and fixing MCB, Three pole, 63Amp, 415V 10KA 'C' curve type Complete all as specfied and directed by Engineer-in-Charge.

S&F MCB SPN 32 Apms, 240 Volts Complete all as specfied and directed by Engineer-in-Charge.

S&F MCB SPN 40 Apms, 240 Volts Complete all as specfied and directed by Engineer-in-Charge.

S&F MCB SP 6-32 Apms, 240 Volts Complete all as specfied and directed by Engineer-in-Charge.

M& L for Taking down submain wiring and M&L for sub main wiring complete with Two runs of 4 Sqmm single core PVC insulated unsheathed,heavy duty, 1100 Volt grade multistranded copper conductor cable (FRLS) and drawer through and including PVC conduit (minimum 20 mm dia) in concealed conduit with all accessories, fittings etc and including one run of PVC insulated and unshethed copper conductor 6.00 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains Complete all as specfied and directed by Engineer-in-Charge. Note: Three run of 4 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length.

Taking out existing unserviceable kiosk terminal box and S&F mounting type weather proof terminal box of size 150 x 150 x 100mm heavy duty (machine mould) consisting of 01 No MCB SP 06 Amps and backlite connector of 32 A for single phase and neutral (Three terminals) for cable in cable out entire complete. Terminal box to be fixed to wall Complete all as specfied and directed by Engineer-in-Charge. Make : Sintex/National or equivalent.

Taking down unserviceable building security light fitting and Supply and fixing pressure die cast housing with epoxy power coated dark graphite grey colour finish. Prismatic polycarbonate cover with individual LED lenses IP65 20 watt, AC 240 Volts 50 HZ Complete all as specfied and directed by Engineer-in-Charge.

Taking down old change over panel and Supply and fix on load change over switch of capacity 200 Amp manual changeover, front handle operated in sheet metal enclosure with making incoming and outgoing connection with sutable size copper cable Complete all as specfied and directed by Engineer-in-Charge.

M& L for Taking down submain wiring and M&L for sub main wiring complete with Two runs of 2.5 Sqmm single core PVC insulated unsheathed, heavy duty, 1100 Volt grade multistranded copper conductor cable (FRLS) and drawer through and including PVC conduit (minimum 20 mm dia) on the surfaces of the walls etc with all accessories, fittings etc and including one run of PVC insulated and unshethed copper conductor 2.5 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains Complete all as specfied and directed by Engineer-in-Charge. Note: Three run of 2.5 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length.

M& L for Taking down submain wiring and M&L for sub main wiring complete with Two runs of 6.0 Sqmm single core PVC insulated unsheathed, heavy duty, 1100 Volt grade multistranded copper conductor cable (FRLS) and drawer through and including PVC conduit (minimum 20 mm dia) on the surfaces of the walls etc with all accessories, fittings etc and including one run of PVC insulated and unshethed copper conductor 6.0 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains Complete all as specfied and directed by Engineer-in-Charge. Note: Three run of 6.0 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length.

Deduct Credit for Demolished/ Dismantled material Rs. (-) 24,465.00 (Minus) as listed in Schedule of Credit. Note 1:- Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'. Note 2:- The tenderer must keep in mind when quoting rates against items having height 2 mts to 5 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

Advait Enterprises (BID ID -3492381)

Super Construction (BID ID -3492192)

archana enterprises (BID ID -3492480)

AMBICA ENGINEERING (BID ID -3489628)