Repair and renovation of Forest Corporation Building, Haddo for Covid Facility Centre under PBND, APWD, Port Blair. SW_ Partition work of Covid Facility Centre at Haddo for proposed ANM Training School.

Amount

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing white vitreous china laboratory sink includingmaking all connections excluding cost of fittings :

Size 600x450x200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete.

Semi rigid pipe 32 mm dia

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Superior hardwood Cart-II (A)

Providing and fixing UPVC (SWR) plain bend of required degree (6Kg/Sqcm)

75mm dia

Providing and fixing UPVC (SWR) soil, waste and vent pipe (6kg/Sqcm)

75mm dia

Providing and fixing UPVC (SWR) single equal plain junction of required degree (6kg/Sqcm)

Providing and laying hollow cement concrete block walling 100mm thick consisting hollow block of size 400 x 100x200mm of mix 1:3:6(1cement :3 coarse sand:6 graded stone agg. 10mm nominal down size) having a crushing strength of 3.5N/mm2 at 28 days as per I.S. 2185 (Part-I) 1979 laid in cement mortar 1:6(1cement : 6 coarse sand).

Upto floor five level

Providing and fixing ISI marked stainless steel sliding door bolts with necessary nuts and screws etc. complete.

Providing and fixing stainless steel handles with stainless steel screws etc complete

Providing and fixing stainless steel tower bolts with necessary screws etc complete

Providing and fixing "File Storage Unit" having one unit maximum size of block 0.75m (L) X 0.45m (W) X 0.75m (h) along with one centre shelves and open shutters made of superior quality marine plywood of 19mm thick(Greenply or equivalent) confirming to IS 710 in three sides and 6mm thick marine plywood (Greenply or equivalent) confirming to IS 710 at backside and all outer visible surface pasted with sunmica as per the colour and design approved by the Engineer-in-charge and pressed minimum 12 hours including snap hingesm lock, handles etc complete. The cabinet fixed on wall inside surface painted with enamel paint and smoothening the surface with chalk putty. (Measurment to be paid for front face only)

Providing and fixing marine plywood partition/panelling of approved quality (Green ply, SIR or equivalent) confirming to IS:710 with necessary nails and screws etc. complete (frame work to be paid separately).

6mm thick marine plywood

12mm thick marine plywood

Providing and fixing stainless steel hanging floor door stopper ISI marked with necessary screws etc. complete

Twin rubber

SANTOSH KUMAR SINGH

Raj Construction

ARJUN MANDAL

SHRI BALAJI ENTERPRISES

M/s V ALAGAR SAMY & SONS