Improvement of Pump Room Building of LIS Suhagani under UT Capex Budget 2025-26.

Amount

Demolishing R.C.C. work manually/by mechanical means includingstacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet

Providing and fixing special quality chromium plated brass cupboard locks of approved quality with six levers including necessary screws etc. complete : 75 mm.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement Mortar.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead :Of area of 3 sqm. and below

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50M ( Stacking of cleaned bricks shall be measured.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in- charge: 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) .

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) .

Brick work with common burn clay ( Non modular) bricks of class designation 7.5. in foundation and plinth including curing in : cement mortar 1:6 ( 1 cement : 6 coarse sand.

Extra for brick work with common burnt clay bricks /cement conc. Bricks in superstructure above plinth level upto floor five level.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels beams girders brussumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floor, roofs landings balconies and access platforms.

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs breaks in floors and walls aove under 20CM wide.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Cold twisted bars.

12MM cement plaster of mix ( 1:4 ) 1 cement : 4 coarse sand.

6 MM thick cement plaster to ceiling of mix 1:3

Filling available excavated earth ( excluding rock) in trenches, plinth sides of foundations etc in layers not exceeding 20CM in depth, consolidating each deposited layer by ramming and watering lead upto 50M and lift upto 1.5M.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete 50 mm thick with 20mm nominal size stone aggregate.

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm

Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: Two coats

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

Providing and fdixing 1MM thick MS Sheet door with frame of 40x40x6MM angle Iron.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.First class kail wood

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing bright finished brass handles with screws etc complete 125Mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :250x10 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. 150x10MM

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Carriage of bricks average 20Km by MT to site of work.

Carriage of sand and stone agg. Avg distance 10 Km by MT.

Lump sump provision for electrication.

M/S ATUL KOHLI (BID ID -2653484)