COMPREHENSIVE REPAIR/MAINT TO CERTAIN BLDGS OF PADMANBHAN and UMRAO ENCLAVE, ASSAYE LINE, MH, MDC, NCC, BGDE CAMP and MES AT AGE AURANGABAD UNDER GE(S) AHMEDNAGAR

Amount

Taking down cement or cement lime plaster on brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and fair without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick on ceiling surfaces of brick work or concrete in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and as directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portions ordered complete all as specified and as directed.

M&L for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 6 above but except bricks.

M&L for preparation of new plastered surfaces of walls and applying two coats of Acrylic emulsion distemper over a coat of acrylic primer complete all as specified and as directed.

M&L for preparation new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and as directed

M&L for preparation of newly plastered surfaces and applying three coats of white wash on wall complete all as specified and directed.

M&L for preparation of surfaces of walls and applying 1mm thick wall care putty complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and as directed

M&L for preparation of plastered or unplastered old surfaces of ceiling applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying one coat of Acrylic emulsion distemper complete all as specified and as directed.

M&L for preparation of old surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying two coat of Acrylic emulsion distemper in any colour complete all as specified and as directed.

M&L for preparation of old surfaces of walls by washing rubbing down & stopping of painted surfaces and applying one coat of cement base paint complete all as specified and as directed.

M&L for preparation of old surfaces of walls by washing rubbing down & stopping of painted surfaces and applying two coat of cement base paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces wall and applying two coats of exterior acryclic emulsion weather coat paint, white or tinted over a coat of primer complete all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces and applying one coat of exterior acryclic emulsion weather coat paint, white or tinted complete all as specified and as directed.

M&L for complete removal of existing treatment of old plastered or unplastered wall surfaces, preparation of surfaces and applying two coats of exterior acryclic emulsion weather coat paint, white or tinted, over a coat of primer complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) and rubbish off the premises etc complete all as specified and as directed.

M&L for coloured non-skid ceramic tiles, 7 to 8 mm thick (Square or Rectangular), area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles, 7 to 8 mm thick (Square /Rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tiles, laid over and including screed bed or bedding layer of 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 26 above but as in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for coloured non-skid ceramic tiles, 7 to 8 mm thick (square or rectangular), area of each tiles exc 0.18 Sqm but n exc 0.38 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 28 above but as in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for Vitrified tiles double charged (light shade) 8 to 9mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in cement mortar 1:6, complete all as specified and as directed.

All as per serial item No 30 above but as in dado/skirting or on vertical surfaces, laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as dircted.

M&L for 10 mm thick double charged/ ultracharged vitrified tiles (any shade), Square or rectangular as in floors area of each tile exc 0.42 Sqm but n exc 1.00 sqm, set and jointed in neat cement slurry & pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 32 above but as in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 complete.

M&L for glazed coloured ceramic tiles (shade as approved by GE) of size 350mm x 250mm x 7mm/450mm x 300mm x 7 mm thick, as in dado, skirting, risers to step etc laid over and including 10 mm thick backing coat in cement mortar 1:4, jointed in neat cement slurry and pointed in coloured cement to match with colour of tiles complete all as specified and as directed.

Dismantling of kota stone slab of any description, laid, bedded & pointed in any mortar all as specified and as directed.

M&L for 20-22 mm thick machine cut kota stone slab flooring (size 22"x22"), as in cooking platform and other similar situation laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including rounding one edge of stone slab, cutting, rubbing and mirror polishing and removing dust complete all as specified and as directed.

All as per serial item No 36 above but as in risers to steps and staircase, skirting etc over and including 10mm thick backing layer of cement mortar 1:3 all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & as directed. Note:- Colour/shade shall be as approved by GE / Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregates as in sub base of flooring, paving etc complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for chequered cement concrete tiles, glossy finish, rubberized, 25cmx25cmx25mm /30cm x 30cmx25 mm thick, as in floors, set jointed and pointed in neat cement slurry with grey cement and pigments over 15 mm screed bed in cement mortar 1:6 complete all as specified & as directed.

Rounding edges of stone slabs, one edge of steps, cooking platform and other similar situations complete all as specified & as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exc 1.50 sqm but n exc 4 sqm each and making good disturbed surfaces of walls in cement mortar (1:3) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area n.exc 1.50 sqm each and making good disturbed surface of walls in cement mortar 1:3 complete all as specified and as directed.

Taking down shutters of any description, area exc 1 sqm & n.exc 2 sqm each leaf and complete all as specified & as directed.

M&L for rolled mild steel work (angle iron or any other section) as in door frame (Chowkhats) & cooler stand confirming to Fe-290 (Gde E165) including preparing back of chowkhat applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and as directed.

M&L for plain cement concrete, type B-0, 1:2:4 (using 12.5 mm graded aggregate) as in bed block, hold fast, coping and similar work etc including necessary form work complete all as specified and as directed.

S&F 30mm thick, factory made flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both faces including 6mm thick teak wood beading all around complete all as specified and as directed.

S&F 35 mm thick second hard wood, factory made, plain framed panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35mm thick IInd class hard wood glazed skelton shutters, factory made, open rebated and prepared to recive glass, guage etc, (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR part - I section - 8, clause 8.20 (a) and fixed to chowkhat complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet reiforced with mild steel square tube, supplying & fixing in openning as per specifications and drawings all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm wood grains Printed PVC sheet reinforced with mild steel square tube, suppling and fixing in opening as per specifications & drawings all as specified and as directed.

S&F 30mm thick factory made solid panel PVC door shutters made out of MS tubes of top and bottom rail mild steel frame shall be covered with heat moulded PVC "C" channel 5mm thick and having width of 50mm for from stiles and H section of 100mm wide for the rails, the inner panel 6mm thick PVC sheet insulated between frame and panel should be struck to the stiles and rails 50x30x5 mm, channel rails 100x30x5 mm H junction all as per drawings / manufacturers instructions complete including locking device and all necessary fitting etc complete all as specified and as directed. Note : The size, design and pattern of shutter shall be approved by GE / Eng-in-Charge.

S&F fatory made solid panel PVC door shutter, 30mm thick (stiles), consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded feathered edges wood grain printed PVC sheet used instead of plain colour PVC sheet & 5 mm thick x15 mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10 mm x 10mm (90 degree) used instead of exposed portion of PVC sheet beading and fixed as per specifications & drawings complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC sheet on back face and fixed as per specification & drawing complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges, steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges, steel handle and steel peg stay complete without glazing bars, complete all as specified and as directed.

S&F powder coated anodized aluminium frames for door, window, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed. Note:- Colour shall be as approved by GE/Engineer-in-Charge.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed. Note:- Colour shall be as approved by GE/Engineer-in-Charge.

S&F powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and as directed. Note : Colour shall be as approved by GE/Engineer-in-Charge.

S&F powder coated aluminium anodized side hung type window/ventilators shutters without sash bars section weight not less than 0.55Kg/RM with extruded built up standard tubular and other sections of approved make according to IS(thickness of powder coating not less than 50micron including necessay glazing clips weight not less than 0.124Kg/Rm for fixing sheet glass anodized aluminium fittings/fixtures such as required number of roller of suitable size interlocking cleats/ plates etc as required for complete fixing window shutters complete all as specified and as directed. Notes:- (i) Only aluminium shutters for the window/ventilator shall be measured and paid under this item. Sheet glass and wiremesh shall be measured and paid in respective items. (ii) Colour shall be as approved by GE/ Engineer-in-Charge.

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed comprises of following sections :- (a) Window frame (i) Bottom- Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m) Note:- Colour shall be as approved by GE/Engineer-in-Charge.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screwsetc complete all as specified and as directed Note:- Colour shall be as approved by GE/Engineer-in-Charge

S&F factory made UPVC any colour sliding window, three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Note: (i) The unit rate quoted shall includes all other connected accessories but exclude cost of glass and . (ii) Net opening shall be measured for payment. Area of window not exceeding 2.00 sqm each (iii) Colour shall be as approved by GE/Engineer-in-Charge.

S&F in position 4.8 to 5mm thick clear float/frosted glass of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium frame exc 0.5 sqm in each pane complete all as specified and as directed.

S&F position 4.8 to 5mm thick float/frosted glass on one side quality and glazing with glazing clips including necessary rubber packing, fixed to PVC/aluminium frame, area n. exc 0.5 sqm in each pane all as specified and as directed.

S&F solid PVC wall lining and solid PVC partitions fixed with aluminium frame/other consisting of 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing complete all as specified and as directed. Note:- Design and Colour shall be as approved by GE/Engineer-in-Charge.

M&L for framed mild steel work, such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; framed baluster, railings and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed

S&F in repair door seal, 0.90m to 1.20m long with brown coated aluminium frame 20mm wide and 0.50mm thick with nylon brush, 30mm wide along full length and fixed to aluminium/wooden doors with screws complete all as specified and as directed.

S&F in repair mild steel 300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L for preparing the new wooden surfaces over 10cm width or girth & applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden/steel frames with tinned tacks or galvanized wire staple & complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames with tinned tacks or galvanized wire staple & complete all as specified and as directed.

S&F in repair 150 mm long floor door stopper of Aluminium alloy body tongue, anodised, with hard drawn steel spring fixed to door all as specified and as directed.

S&F Mild Steel 300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F 75 mm size stainless steel butt hinges, medium weight, cold rolled, ISI marked, complete all as specified and as directed.

S&F butt hinges medium weight cold rolled mild steel ISI marked size 100 mm size complete all as specified and directed.

S&F butt hinges medium weight cold rolled, mild steel ISI marked size 125 mm size complete all as specified and directed.

S&F 125mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and as directed.

S&F 150mm aluminium handle fabricated type, anodised conforming to IS complete all as specified and as directed.

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and as directed.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed.

S&F in repairs aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 200 mm long complete all as specified and as directed.

S&F in repairs aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and as directed.

S&F in repair 150mm aluminium handle fabricated type, anodised conforming to IS complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F in repair 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F in repair stainless steel handle 100 mm size complete all as specified and as directed.

Resecuring or easing of door shutters exc 1 sqm but n.exc 2 Sqm for easy closing / opening tightening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts with new screws etc complete all as specified and as directed.

Resecuring or easing of window shutters, kitchen cupboard shutters, show case shutter drawers incl fixing of screws adjusting handles, knobs,tightening piano hinges incl misc small adjustments complete all as specified and as directed.

Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed.

Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed.

M&L for 15mm dia UPVC pipes Pressure rating 10 kgf/cm2, laid in floors / trenches/fixed to walls including fittings (Elbow, Tee, FTA, Socket, reducer, solvent etc) complete all as specified and as directed.

M&L for 20 mm dia UPVC pipes Pressure rating 10 kgf/cm2, laid in floors / trenches/fixed to walls including fittings (Elbow, Tee, FTA, Socket, reducer, solvent etc) complete all as specified and as directed.

M&L cutting chases, in brick wall/plaster, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

S&F in repair, vitreous China wash hand basin, white, flat back, size 550x400mm including brackets, waste coupling 32mm of PTMT (half or full threaded) (Minimum weight 32mm 45gms), waste pipe complete all as specified and as directed.

S&F in repair vitreous China, Squatting pan, Orissa pattern, size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and as directed.

S&F in repair vitreous China wash down water closet pan (pedestal pattern), white, including plastic white seat cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and as directed

S&F in repairs, viterous China urinals, half stall, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including brass chromium plated urinal spreader, flush pipe, grating and union for discharge pipe and PVC waste pipe 32mm dia all as specified and as directed.

S&F in repair PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and as directed.

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repair Chromium plated/Stainless steel Jet with flexible tube upto 1 metre long with S.S. triangular plate to vitreous China wash down water closet pan (pedestal pattern) complete all as specified and as directed.

S&F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and as directed.

S&F in repair PVC waste pipe 32mm bore 600mm long with one end socketed complete all as specified & as directed.

S&F in repair Stainless steel grating, square of 100mm size with centre hole to fix waste pipe complete all as specified & as directed.

S&F in repair Stainless steel grating, square, 100mm size complete all as specified & as directed.

S&F in repair soap dish cast Copper alloy , Chromium plated, fancy type, fixed on wall/ tiles with chromium plated brass screws complete all as specified & as directed.

S&F in repair vitreous china wash down water closet, one piece/ curatore cascade with cistern set and soft close glossy (white) seat cover complete all as specified and as directed.

S&F in repair, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and as directed.

S&F in repair 15mm bore brass Chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and as directed.

S&F in repair 15mm bore brass Chromium plated center hole wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repair brass Chromium plated shower rose, 125mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified & as directed.

S&F in repairs, stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repair 15mm bore dia stop valve, angle valve of cast copper alloy, fancy type CP long body (concealed type) high pressure screwed for iron pipe complete all as specified and as directed.

S&F in repairs, bib tap 15mm dia, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair 15mm bore chromium plated two way angle cock, screwed down,high pressure,with crutch or butterfly handle for iron pipe and fixed, complete all as specified & as directed.

S&F in repairs 15mm bore, fancy type pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with orwithout lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as specified & as directed.

S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all as specified and as directed.

S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass corner shelf complete all as specified and as directed.

S&F in repair sink made of stain less steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union overall size not less than 495x420mm, bowl size 410x330x 160mm complete all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair 32 mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repair bevelled edge looking mirror 5.5mm thick of size 60cmx 45cm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position and connecting including dismantling existing water tank all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position and connecting including dismantling existing water tank all as specified and as directed.

M&L for cleaning of service tank upto 500 ltrs by removing all scale, dirt, silt, mud etc, from tanks and from mouths of circulating pipes including washing of tank internally with bleaching powder after removing scale dirt mud etc from tank and removing algae outside from tank from below bottom of tank and disinfecting tank by soraying sodium hypochlorite solution in tank writing down date of cleaning on tank by synthetic enamel paint size of alphabet/ numerical shall be minimum 7 cm using stencils complete all as specified and as directed Note:- The unit rate quoted shall include dismantling and refixing of water tank and check float valve refixed or provide new as applicable as etc complete.

M&L for cleaning of service tank upto 1000 ltrs by removing all scale, dirt, silt, mud etc, from tanks and from mouths of circulating pipes including washing of tank internally with bleaching powder after removing scale dirt mud ec from tank and removing algae outside from tank from below bottom of tank and disinfecting tank by soraying sodium hypo chlorite solution in tank writing down date of cleaning on tank by synthetic enamel paint size of alphabet/numerical shall be minimum 7 cm using stencils complete all as specified andas directed. Note:- The unit rate quoted shall include dismantling and refixing of water tank and check float valve refixed or provide new as applicable as etc complete.

S&F in repair cover/lid for PVC any type water storage tank covers suitable for 500/1000 litre capacity all as specified and as directed

S&F in repair 20mm dia ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, compete (Minimum weight 210 gm) complete all as specified & as directed.

S&F in repair 15mm dia ball valve high pressure of PTMT with apoxi coated aluminium rod and high density plastic ball screwed for iron pipe all as specified and as directed

S&F in repair 20 mm dia gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, ISI marked complete all as specified & as directed.

S&F in repairs 25 mm dia gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union ISI marked complete all as specified & as directed.

S&F in repairs, 20mm dia harrison curtain rails, mild steel, plastic coated, fancy type with fixing brackets, stops with knob etc complete all as specified and as directed.

S&F in repairs toilet paper holder of chromium plated fixed to walls with chromium plated brass screws complete all as specified and as directed.

M&L for special treatment to sunken slab floor including WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 CPS over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC vitreous china squatting pan 580x440mm with integral footrests/pedestal pan incl seat cover, white, area of WC n exc 1.50 Sqm each etc after dismantling the existing sunken floor etc complete all as specified and as directed. Note : Work shall be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specifications as approved by GE.

All as per serial item No 138 above but floor area of WC/bath-room/toilet exc 1.5 Sqm but not exceeding 3.0 Sqm.

S&F in repairs, 75 mm dia PVC(SWR) nahani/floor trap with grtaing including jointing to waste pipe with solvent cement complete all as specified and as directed.

Hacking out of old broken glass (any thickness ,size quality or description/ any height of building ) from wooden / metal frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or beads in square n.exc 0.50 sqm in each pane, of any description complete all as specified and as directed.

S&F 3 mm thick frosted/figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

M&L for welding work in repairs n. exc 2.5cm in length to n.exc 6mm thick of metal surfaces complete all as specified and as directed.

S&F in repair 18/19mm thick prelaminated particle board, interior, grade prelaminated one side with decorative choice lamination and other side balancing white, including teak wood lipping 19 x 6mm thick fixed with nails in shelves,cupboard shutter and similar works all as spepcified and as directed.

S&F in repair continous (Piano) hinges, brass finish of whem open 30mm width of flaps complete all as specified and as directed

S&F in repair 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and as directed

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed

S&F in repair magnet catcher with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed

Dismantling asbestos cement sheet (corrugated or semi corrugated etc) including ridges in large patches as in roof covering complete all as specified and as directed. Note:- Dismantling existing wind tie and refixing the same where required for taking down of sheets shall deemed to be included in the unit rate quoted .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spaced exc 15 cm complete all as specified and as directed.

Dismantling of timber scantling 40Sqcm and over in section in any position such as in rafter, purlins etc in unframed work complete all as specified and as directed

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position all as specified and as directed.

M&L for second class hardwood batten, clean sawn, sectional area exc 5sqcm & n.exc 15 Sqcm at spacing 15cm centre complete all as specified and as directed.

Cutting holes into or through brick wall built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified & as directed by Engr-in-Charge.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates and cooler stand and similar work confirming to Fe 410W(Gde E-250 quality A) complete all as specified and as directed

M&L for rolled mild steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections conforming to Fe 410-W(Gde-E250) quality A) including distance pieces, cleats etc. all as specified and as directed.

M&L for 6mm thick asbestos cement corrugated or semi corrugated sheets in roof, wall etc. fixed with L-type or cranked hook bolts (at any height of building) including necessary scaffolding complete all as specified and as directed.

M&L for 6mm thick asbestos cement two piece adjustable plain wing ridge fixed with L-type or J-type or cranked hook bolt (at any height of building) including necessary scaffolding complete all as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated/ Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified & as directed. Note:- Colour & Pattern shall be as approved by GE/Engineer-in-Charge.

S&F prepainted galvalume aluminum zinc coating GI based mangalore pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified & as directed. Note:- Colour & Pattern shall be as approved by GE/Engineer-in-Charge.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & as directed.

Dismantling mangalore pattern or similar tiles in roofing complete all as specified and as directed.

M&L for roof tiles mangalore pattern, interlocking at side joint laid dry complete all as specified and as directed.

M&L ridge or hip tiles to suit Mangalore pattern or roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed.

S&F laminated Gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, including dismantling existing false ceiling work of any description all as specified and as directed.

Taking down wall panelling and similar work of any type complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and as directed.

S&F solid PVC wall lining consisting of 5mm thick of any design and colour PVC sheet inclusive of solvent cement and strip & channel feathered at the edges for fixing on PVC wall lining as per specifications and drawing complete all as specified and as directed. Note:- Design and colour shall be as approved by GE/Engineer-in-Charge.

S&F in repair window venetian blinds of approved colour imported cloth blinds, horizontal / Vertical including stainless steel channels, sliding nylone rope & all necessary fittings and fixtures as required complete all as specified & as directed. Note:- Design and colour shall be as approved by GE/Engineer-in-Charge

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in PCC band, PCC beam, benching of drain, coping, slightly rounded or chamfered angles and throating, and similar work including necessary formwork complete all as specified and as directed.

Demolition of reinforced cement concrete in any description and in any position not otherwise specifically provided (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works flat n exc 200mm thick (Horizontal or slopping) for fair finished surfaces complete all as specified and as directed.

M&L for form work to edges of concrete flats, treads floor and roofs n exc 20 cm wide and sides of RCC/PCC bends in walls (horizontal or slopping) and similar works exc 10 cm but n exc 20 cm wide for fair finished surfaces complete all as specified and directed.

M&L for mild steel TMT bars, 8mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M & L for RCC 1:2:4 (Nominal Mix), type B-1, using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and shelves and the like etc .complete all as specified and as directed.

Taking down PVC SWR pipes (any size or pattern), including all fittings like heads, shoes, bends etc complete and all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed with rubber ring joints, laid in trenches or in floors complete all as specified & as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & as directed.

S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & as directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Supply only stack clamps made out of 50mm by 3mm flat iron and 16 mm dia round iron stays fixed to pipe of bore 110mm complete all as specified.

S&F PVC bend/ shoe of dia. 110mm complete all as specified including taking down old unserviceable complete all as specified and as directed.

sunil kaduba dakale (BID ID -3122753)

D V Engineers and Contractors Pvt Ltd (BID ID -3121766)

M/s.M G Kulkarni (BID ID -3109472)

sonu enterprises (BID ID -3109625)

M/S Tirupati Goroba Shendge (BID ID -3124107)

M/S. M.A. Sharief engineers and contractors (BID ID -3111197)

M/s S.R lahoti (BID ID -3101087)

B.R.ANAND (BID ID -3099494)