SPECIAL REPAIR TO BUILDING NO 3AC AND ROOF WITH CONNECTED WORK AT BUILDING NO CB 03 BAYONET SCHOOL AT INF SCHOOL UNDER GE MIS MHOW

Amount

B/R ITEMS:

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) area not exceeding 1.5 sqm each complete all as specified

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) area exceeding 1.5 but not exceeding 4.0 sqm each complete all as specified

S & F second class hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified

S&F 35mm thick factory made second class hard wood plain, framed pannelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified

S & F 35 mm thick factory made, second class hard wood glazed and skeleton shutters open rebeated and prepared to received glass, gauzed, without sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR Part-I Section 8, clause 8.24 (a) and for door and fixed with chowkats, chemically pressure treated complete all as specified

S&F factory made both side prelam PVC sheet door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with ms square tube, & edges will be painted to match with prelam sheet complete all as specified and as directed. Note: Colour/Texture Style of Frame / Prelam Sheet shall be approved by GE

S&F factory made both Side Prelam PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Single Side Prelam PVC sheet for top rail, lock rail & bottom rail. Panelling of Single Side Prelam PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement including Hinges for fixing handle/tower bolt as per site requirement complete all as specified and as directed. Note: Colour/Texture Style of Frame / Prelam Sheet shall be approved by GE

S&F factory made 25 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free, water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws including necessary Locking arrangement complete all as specified and as directed. Note-:(a)Colour/Texture Style of Door/Prelam Sheet shall be approved by GE (b)Test certificate from original Manufactuer shall be provided before incorporation in the work site.

S&F factory made 100% solid WPC (Wood polymer composite) Door frame 90mm X 45mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade), calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/borer proof, water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-charge.Note-:(a)Colour/Texture Style of Door/Prelam Sheet shall be approved by GE (b)Test certificate from original Manufactuer shall be provided before incorporation in the work site.

S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section

S&F aluminum alloy handles fabricated anodised of 150 mm long

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring and rubber piece in floor

S&F 25 mm dia Stainless steel chromium plated drappery curtain rod with standard weight and thickness including desiner bracket and other necessary fixing accessories complete all as specified .Note :Design /Size of Bracket shall be approved by GE .

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified

M&L for applying two coats of first quality oil emulsion distember over a coat of primer over a coat of Acrylic / Water proofing wall Putty on walls complete all as specified . Note:- Putty shall be measured and paid seperately under relevant item.

M&L for preparation of old decorated surface of wall including brooming , scraping down smoke spot, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and applying two coats of first quality oil emulsion distemper white/coloured over a coat of Acrylic / water proofing wall Putty (where ever required at site in patches) all as specified and directed by Engineer-in-Charge. Note:- Putty shall be measured and paid seperately under relevan item.

M&L for applying two coats of Acrylic Smooth exterior paint of required shade @ 1.67 litre /10 sqm over and including a coat of primer @ 2.20 kg /10 sqm of same make base over a coat of Acrylic / water proofing wall putty all as specified Make: Asian - Apex or other equivalent as approved by GE

M&L for preparation of old decorated surface of wall including brooming , scraping down smoke spot, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and applying two coats of exterior weather proof water base emulsion paint white / coloured over a coat of primer of same make over white cement based putty (where ever required in site in patches) all as specified .Note: Putty shall be measured and paid seperately under relevant item . Make: Asian - Apex or other equivalent as approved by GE

M&L for preparation of newly plastered surface of wall and and applying 2mm thick Acrylic / water proofing wall putty in two coats (each coat not less than 1mm thick ) and surface finished even and smooth with sand paper complete all as specified

M&L for applying 2mm thick Acrylic / water proofing Wall putty on walls and surface finished even and smooth with sand paper complete all as specified

Demolition of brick work built in cement mortar of any description including all quions ,arcches , pillars etc complete all as specified

M&L for brick work in cement mortar 1:6 using sub class `B ` modular brick straight or curved on plan exceeding 6.0m mean radius complete all as specified

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement complete all as specified

M&L for rendering 10 mm thick in cement mortar 1:6 on fair faces of wall / concrete surfaces finished even and fair complete all as specified

M&L for rendering 5mm thick in ceiling in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified

M&L for preparation of old painted surfaces of wood / wood based materials exceeding 10cm in width or girth and applying one coat of synthetic enamel paint all specified.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick ( below or above ground level ) complete including removal of debries out side MD land all as specified and as directed .

M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in sub base, levelling course, etc complete all as specified

M&L for PCC1:4:8 type D2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified

Dismantling of floor, hearth , or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the primeses complete all as specified

M&L for scratch free Glazed (Porcelain) Vitrified Tiles (GVT)/ Polished Glazed Vitrified Tiles (PGVT) 9mm to 10mm thick (square or rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.72 sqm ( ie) size 600x1200 in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed. Make of tile : Superior quality tiles from Kajaria/Somany/Orient Tiles. Note : (a) Size and pattern / texture of GVT (Matt Finish) / PGVT(Glossy Finish) shall be approved by GE (b)Glazed Coating on GVT / PGVTshall not be less than 1mm thick .

All as per item No 31 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified

M&L for scratch free Glazed (Porcelain) Vitrified Tiles(GVT) /Polished Glazed Vitrified Tiles (PGVT) 9mm to 10mm thick (square or rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm (ie) of size 600x600mm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified Make of tile : Superior quality tiles from Kajaria/Somany/Orient Tiles. Note : (a) Size and pattern / texture of GVT (Matt Finish) / PGVT(Glossy Finish) shall be approved by GE (b)Glazed Coating on GVT / PGVTshall not be less than 1mm thick .

All as per item No 33 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified

M&L for glazed ceramic coloured tiles (Matte /Gloss Finish) of size not less than 450x300x7 mm thick on vertical surfaces such as wall ,dado,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 15 mm thick backing coat on fair faces of brick work in CM 1:4 complete all as specified Make of tile:- Superior quality tile from Kajaria/Somany/Orient tiles. Note:Pattern/Texture and finish of wall tile shall be approved by GE

M&L for glazed ceramic coloured tiles (Matte/Gloss Finish) of size not less than 300x600x7 mm thick on vertical surfaces such as wall,dado,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 15 mm thick backing coat on fair faces of brick work in CM 1:4 complete all as specified Make of tile:- Superior quality tile from Kajaria/Somany/Orient tiles. Note:Pattern/Texture and finish of wall tile shall be approved by GE

M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular) of size 400x400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile including 15mm thick screed bed or bedding layer in cement mortar 1: 6 complete all as specified Make of tile:- Superior quality tile from Kajaria/Somany/Orient tiles. Note:Pattern/Texture and finish of wall tile shall be approved by GE

S&F Mild steel framed work as in doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc, to prepared for hanging or sliding with including either hooks and hinges also fastening grills, grating, hold fast of doors and windows chowkat etc, with ends of bars shouldered and or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanksand fixing and similar work confirming to Fe 290 Gde E-165 including dismantling and removing of existing timber structure if any complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified .

M&L for machine cut kota stone slab in flooring 20mm to 25mm thick laid over and including 15mm thick screed bed in cement mortar 1:6 and pointed with cement mixed with pigment to match with the shade of slab including rubbing and polishing complete all as specified

M&L for 18mm to 20 mm thick Granite slab work (table rubbed and polish) of approved quality of required size in floor,wall,cooking platform and like bedded and jointed in grey cement slurry and pointed with coloured cement (1:2) usig marble dust with admixture of pigment to match the shade of granite stone laid over and including 20 mm thick screed bed in cement mortar 1:4 including polishing by using mechanical grinder complete all as specified and directed. Note : Size of Granite slab shall be maximum as available at market /as per site requirement and shall be approved by GE

M&L for 60mm thick machine pressed rubber moulded precast cement concrete interlocking paver block (glossy finish) of M-35 Gde of approved shape, size and colour conferming to IS 15658-2006 and including joints filled with sand and stone dust 50mm thick as in levelling course of interlocking complete all as specified

M&L for chequered cement concrete tiles with grey cement and pigment of size 30cmX30cmX30mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for chequered cement concrete tiles with grey cement and pigment of size 40cmX40cmX40mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stone / kerb block ,machine pressed ,bul lnosed shape at top as directed and finished the surface even and smooth including necessary form work /moulding ,fixing, jointing kerb block in cement mortar (1:4) complete all as specified

M&L for preparation of old decorated surfaces of wall by removing existing putty/distemper complete and applying two coats of sureseal of Dr Fixit or other equivalent as approved by GE and subsequently applying two coats of Oil Emulsion Distemper over a coat of 2 mm Acrylic/WaterProofing Wall Putty(each Coat not less than 2mm) complete all as specified and directed. Note: (a) First coat of sureseal (no dilution) shall be applied and allow it to dry for 6-8 hours. (b) Second coat of sureseal (no dilution) shall be applied, Perpendicular to first coat direction and allow it to dry for 6-8 hours. (c) Application of sureseal treatment shall be executed through expert team of Manufacturer or through authorised applicator of Manufacturer.

M&L for preparation of old / new plastered surfaces of wall and applying two coats of Rain Coat Neo ( Dr Fixit or other equivalent ) over a coat of 2 mm thick Acrylic /Water Proofing Wall Putty complete all as specified and as per Manufacture's instruction . Note:(a) Apply first coat of RainCoat Neo and allow it to dry for 6 to 8 hours (b) Apply second Coat of RainCoat Neo perpendicular to first coat and allow it to dry for 6 to 8 hours (c) Application of RainCoat Neo treatment shall be executed through authorised applicator of Manufacturers and quantity of Raincoat Neo shall be as needed by the expert team on site requirement (d) Shade/Colour/Texture of Raincoat Neo shall be approved by GE before execution (e) Putty Shall be measured and paid Seperately under relevant item

S&F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters with glazed /Glass and one shutter with wire mesh) with following specification complete all as specified and as directed by Engineer-in-charge. (i) Windows frame of cross section 101mm x 44mm (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm (iii) Sliding shutter frame of cross section 40mm x 18mm (iv) 4 mm thick glass superior quality. (Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 No. (Min) (vii) Sliding rollers per shutter - 02 Nos. (Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutter- 01 No. Note:(a)Thickness of Aluminium Section should be 2 to 3mm. Over all thickness and Cross Section of Aluminium section if any increase in above specification shall be approved by Engineer in Charge as per Site requirement without any extra cost. (b) Size / drawing of Window shutter shall be provided by Engineer in Charge during execution as per site requirement.

S&F powder coated aluminum door with the following specification and making good the disturbed surfaces as per existing finishes complete all as specified and as directed. (a) Cross section of chowkhat frame 101.60 mm x 44.45mm (b) Cross section of hanging and meeting style 83 mm x 44mm (c) Top rail of cross section 114 mm x 44 mm (d) Bottom rail of cross section 114 mm x 44 mm (e) Locking rail (middle rail) of cross section 83 mm x 44 mm (f) 4 mm thick glass superior quality. (Min) (g) Aluminum handle eisc type -02 Nos per shutter (inside & out side). (h) Aluminum door stopper heavy duty-01 No per shutter. (i) Aluminum tower bolt 200mm long-01 No per shutter (inside). (j) Concealed Lock with key superior quality makae and type as approved by GE openable both from inside & out side -01 No per shutter. Note :- (1)Thickness of Aluminium Section should be 2 to 3mm. Over all thickness and Cross Section of Aluminium section if any increase in above specification shall be approved by Engineer in Charge as per Site requirement without any extra cost. (b) Size / drawing of door shutter shall be provided by Engineer in Charge during execution as per site requirement.

M&L for 25mm thick plain cement concrete1:2:4, type B1, using 20 mm aggregate as in roof padding etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on roof surface including mixed with WPC as per manufacturer's instruction's and finishing the surfaces even and smooth without using extra cement complete all as specified

M&L for providing water proofing roof treatment with polymeric standard water proofing membrane, Aqua flex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd / Hyperplas manufactured by IWL Ltd with 10 years guarantee for water tightness complete all as specified as under and all as per Manufacture's instruction :- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 grade @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufacturer's specification complete all as specified and directed. (b) Supply & laying water proofing APP polymeric membrane 3mm thick and 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100 micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed (C) Applying one coat of polymeric modified bitumen 85/25 grade @ 1.2Kg/Sqm over APP membrane (d) Applying two coats of Aluminium bituminous paint @ 0.15 Kg/Sqm over the APP membrane surface. NOTE:- Application of water proofing treatment shall be executed through expert team of manufacturers or their authorised applicator

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings etc complete all as specified

Dismantling of timber scantlings as in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in un-framed work complete all as specified

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting / sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.

S&F Plain, galvanised, mild steel sheeting 0.63 mm thickness as in ridges,hips, valley gutters on roof,with grade of zinc coating 275 with all fixing arrangement complete as directed and specified.

S&F mild steel hollow ,Joist, channel, angle, tee or tubular Section work in tubular trusses, purlins, rafter, tubular column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified .

S&F Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for RCC M-25 grade concrete (Design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, etc complete all as specified.NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) etc rough finished surface of concrete complete all as specified

M&L for high strength steel deformed TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, etc complete all as specified

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified

S&F for anodised aluminium snap grid of 605mmx605mm size frame work for false ceiling with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

M&L for exposed metal frame ceiling with 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid frame work complete all as specified.Note: Frame work shall be measured and paid separately under relevant item.

S&F Gypsum Board 12mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre on GI frame work for seamless ceiling comprising of GI perimeter chennel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm susoended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre inluding finishing the joint of face board with specially formulatted jointing compound and 48 mm wide fibre tape to provide seamless finish Ceiling shall be sealed at joints and finished with jointing compound etc complete including finishing the exposed surfaces of false ceiling with two coats of plastic emulsion paint over a coat of primer complete all as specified and directed.

S&F PVC Ceiling Lining (False Ceiling) consisting of 5mm thick Plain colour PVC sheet 8 to 10 mm hollow section inclusive of solvent cement and fixing at site on frame work as per requirement on site complete all as specified

S&F fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partitions with one or more rebates sections of approved tint as required for partitions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified

S&F aluminium coloured power coated partition,window , ventilator shutters, sliding type without sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws complete all as specified and directed.

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors /window /partition including necessary cutting / moulding and chamferring of edges for service window /counters complete all as specified .

S&F for galvanised Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples etc complete all as specified

S&F PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet 8 to 10 mm hollow section inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, including taking down of old board, complete all as specified

S&F Veneered decorative 18 mm plywood, grade 1 (with BWR resin) with decorative laminate min 1mm thick on both faces, fixed with screws to timber frame work as in cupboard shelf/partition including taking down the existing structure / board on site all as specified . Note : Colour and texture of laminate shall be approved by GE

S&F factory made PVC shelf / partition of required size consisting of panel of 18 mm thick required size consisting of panel of 18 mm thick celuka PVC ply and for supporting the hold of shelf / partition and shall provided 3 edges in size 18mm x 18 mm as per required length the front side of the edge visible in the front of the shelf/partition to be edge lipped by 18mm width x 1 mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company , using solvent cement etc. complete all as specified and directed by Engineer-in-charge.

S& F in repair Rotational moulded Polyethylene water storage tank 1000 litres capacity (cylidrical vertical with closed top) three layered hoisted and fixed in position all as specified in SSR part I complete all as specified

S& F in repair Rotational moulded Polyethylene water storage tank 500 litres capacity (cylidrical vertical with closed top) three layered hoisted and fixed in position all as specified in SSR part I complete all as specified

S&F in repair 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified and as directed.

All as per item no 76 above but 20mm bore

S&F in repair vitreous china European wash down water closet pedestal pattern of size 570x370x390mm white including seat cover ,"p" or "S" trap excluding flushing cistern and flush pipes complete all as specified and as directed .Make :Plumber Cat Part No.- PBW-EWC-001P/002S or other equivalent as approved by GE

S&F in repair PVC valveless,syphonic action type flushing cistern, 10 litres capacity ,low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed.Make : Parryware/Plumber/Essco of jaguar (Economical Range)

S&F in repair CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified .Make:Plumber/Essco of jaguar(Economical Range)

S&F in repair fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed.Make: Parryware Cat Part No: T1381A1 or other equivalent as approved by GE

S& F CP toilet paper holder with Lid Cover complete all as specified and as directed.Make :Plumber/Essco of jaguar(Economical Range)

S & F in repair vitreous china wash basin white table top of size 490x400x145 mm including 32mm brass CP waste coupling complete all as specified . Make :Plumber Cat Part No: CTB-2315 or other equivalent as approved by GE

S&F in repair vitreous china Single Piece WC of size 650x375x720 mm white with "P" or "S" trap ,UF soft close slim seat cover, hinges, dual flushing cistern fitting, fixing accessories and flush pipes complete all as specified and as directed . Make: Plumber Cat Part No: PBW-OWC111P or other equivalent as approved by GE

S&F health faucet with flexible pipe of one metre length including wall hook for EWC complete all as specified.Make:Plumber/Essco of jaguar (Economical Range)

S&F in repair chromium plated shower rose with siwel joint and arm not less than 20cm long suitable for 15 mm bore GI pipes comlete all as specified Make :Plumber/Essco of jaguar(Economical Range) Note:Size/Shape/Design of Shower rose shall be approved by GE

S&F in repair CP wall mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and as directed.Make:Plumber ,Cat Part No: KNA-5100-LB or other equivalent as approved by GE

S&F in repair CP 15 mm Tall Body wash basin mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe etc complete all as specfied and directed Make :Parryware ,Cat Part No: T1346A1 or other equivalent as approved by GE

S&F in repair CP 15 mm Kitchen Sink mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe etc complete all as specfied and directed . Make: Parryware ,Cat Part No: T5035A1 or other equivalent as approved by GE

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450 mm long complete all as specified .

S&F in repairs PVC waste pipe for urinal/wash basin/ sink pipe 32mm bore 65cm long complete all as specified

S&F in repairs of brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets complete all as specified

S& F in repair CP towel ring, dia not less than 200mm complete all as specified

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. Note:Size/Shape/Thickness of Glass Shelf shall be approved by GE

S&F in repair corner glass shelf (with bracket) all as specified and directed Note:Size/Shape/Thickness of Glass Shelf shall be approved by GE

S&F in repair 150 mm long ordinary rat tail rod pattern spring including roller and roller plate complete all as specified

S&F CP grating 100mm dia complete all as specified

S&F in repair PVC (SWR) floor trap plain or multi with stainless steel grating including joining to waste pipe with solvent cement , dia of outlet 75mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints laid on wall / floor complete all as specified

S&F in repair PVC ( SWR) bends any radius bore of 100 mm all as specified

S&F in repair sink with drainage board made of stainless steel 1.0 mm thick in kitchen with plug , washer and waste including fixing cantilever bracket in wall with CM (1:6) and connection to union pipe , over all size 915x460 mm with bowl size 410x330x160 mm complete all as specified .

S&F in repair stainless steel plate rack of suitable size for kitchen made with 1 mm thick stainless steel sheet of best quality with suitable hanging arrangement and fixed to wall complete all as specified and as directed . Note:- Size and weight of rack shall be approved by GE

M&L for providing precast cement concrete louvers and jallies 50mm thick (measured solid), made with cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate, set in cement mortar (1:4) including all moldings but excluding frame complete all as specified and as directed.

S&F in repairs salt glazed stoneware drain pipe of 150mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified .

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested internal dia of pipe 150mm complete all as specified

M&L for RCC type 1:2:4 type B1 using 20 mm graded granite stone aggregate) as in precast cover slab for manholes and soak well cover slab etc set in cement mortar (1:4) etc with and including necessary form work all as specified . Note:- Reinforcement shall be measured & paid separately under relevant item.

M&L for plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations, filling and mass-concrete complete all as specified

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for shafts, wells, cespits, manholes, pier hold etc not exceeding 10 Sqm on plan and getting out in had/dense soil complete all as specified

Excavating over area not exceeding 1.5 m deep and getting out getting out in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified

Returning, filling in, soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete.

Demolition of cement concrete (unreinforced) in roof / terrace other than ground floor etc, including existing roof treatment of any description not exceeding 15cm thickness all as specified. and directed

E/M PORTION:

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good distrubed surfaces of walls, floors etc. complete all as specified

Taking down ceiling fan / exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engineer-in-charge for the following

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on Same board.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on Independent board.

(e) One bell point controlled by one, bell switch 5 Amps

All as per item No 122 here in before but wiring with 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point on independent board including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

All as per item No 122 here in before but wiring with 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for geyser point/AC point connecting to metal plug and socket DB incl necessary running of 4.0 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Modular Switch , single pole, one way, and 5/6 Amp single module

S&F Modular Switch , single pole, one way, and 15/16 Amp single module

S&F Bell push modular 6 Amps single module

S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module

S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module

S&F modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply

S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified

S&F Modular type TV Socket out let complete all as specified

S&F in repairs LED ceiling light fittings 34/36 watt recess mounting type 2x2 luminaire, 6000k complete with driver duly connection wire etc complete . Make: Jaguar Cat No. LSVR01S036XC, Crompton Cat No. LCTLRN-36-FO-CDL, Bajaj Cat Pt No. BZRSQL 36W GZ1 WH or other equivalent in Havells/ Wipro.

S&F in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or other equivalent in Wipro

S&F Decorative ultra slim LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified and as directed. Make : Havells Cat No LHEXACP7IN1W010 or other equivalent make in / Wipro/Philips.

S&F Decorative wall mounted luminaire brushed nickel finish fixture with opal glass diffuser made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 7W watts complete all as specified and as directed. Make: Havells Cat No LHFOAJE1TZ11060 or other equivalent make in Philips/Crompton/wipro.

S&F Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed.Make : Bajaj Cat No : BIBWP 10W LED or other equivalent make in Philips/ Wipro/Havells

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make : Bajaj Cat No ENXT P 36L WH CR PC SD or other equivalent make in Philips, Wipro/Havells

M&L for Sub main wiring in repairs with two runs of single core FRLS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25/32 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FRLS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engineer-in-Charge.- Note:- Two runs of 6 sqmm wiring cable,one run of 6 sqmm earth cable and one run of PVC conduit shall be measured as one unit length.

S&F PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

S&F in repairs double door TPN DB 04 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed Make:- HPL/L&T/HPL/Havells

S&F in repairs double door SPN DB 08 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed . Make : HPL/L&T/HPL/Havells

S&F in repairs MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium /copper lugs complete all as specified and directed . Make:- HPL/L&T/HPL/Havells

S&F MCB SPN 6 to 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

S&F in repairs metal clad box suitable for 230 volt 50 Hz for AC connection three pin and socket with MCB SP 20/32 Amps complete all as specified and as directed

S&F Brushless direct current motor (BLDC) ceiling fans complete with blades (03Nos), suitable length of down rods, with remote control and accessories , 230 V, 50 Hz, 1200 mm sweep, Min air delivery 210 CFM with service value greater than 7.00 BEE , Five star rated, provide electrical connection from ceiling rose to fan terminal by providing flexible cable three core Copper conductor of size 23/0.0076 (3 Core x 0.50 Sqmm), ISI marked including write down MES Number on fan with black paint / permanent Marker complete all as specified and directed .Make: Havells/Orient/Bajaj

S&F Exhaust fan , steel body AC single phase, 230 V of size 300 mm sweep ventil air DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection including making suitable size of hole into existing brick wall to fix fan base compelte all as specified and directed.

S&F energy efficient exhaust fan of metal body 225/230 mm sweep Ventil Air -DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection including making suitable size of hole into existing brick wall to fix fan base compelte all as specified and directed.

S&F water heater storage type of 5 Star rating, capacity 25 liters with glass coated heating element to protect the heating element from oxidation and carbonization. The geyser should be tough enough to withstand pressure upto 8 bars . The inner tank should have a minimum 7 years warranty . The geyser should have company fitted and warrented ELCB or shock safe plug including PTMT connections 15 mm size with nuts and length of 450 mm with all accessories such as safety valve, thermostate including all fixing arrangements as required complete all as specified and as directed.

S&F three phase Electronic Energy Meter accuracy Class 1.0, 3X, 240V, with in-home display 10-60A, 50Hz, counter type display with transparent hinge type Box. self locking meter seal, LCD diplay with optical port, anti temper features, LCD test ,serial no, Date, RTC,Cumulative Kwh, Last bill Kwh, Instanteous Load, KW,Volts,PF,HZ, total Tamper Count, including all incoming and out goinig connections .Make:HPL Model No TPPC1510000002OC00 or other equivalent make in L&T/ Secure

Supply, installation, commissioning and testing of factory made Meter box for three phase meter 300mm x 300mm x 170mm , made out of IP 66 thermo plastic PS polystyrene weather proof with multi level knock out for cable glands in different sizes at bottom of the box , rain water proof,wall thickness 3 mm including complete internal wiring with 6 sqmm copper wire complete all as directed for JCO, OR, Civilian Md Accn Make : Hensel/L&T/Havells

Earthing complete with galvanisedsteel earth plate electrode60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate otless'than 1.5 metres below normalground level, connected togalvanised earth lead wire 4.0mm dia by means of bolts, nuts, checknuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 m from earth plate shall deemed to be included in rate quoted.

Taking down existing old existing unserviceable LT UG / service cable of any description and size complete all as specified

Excavation in trenches not exceeding 1.5 metre wide & not exceeding 1.5 meter in depth for foundation ,laying of cable or pipe and getting out in soft/loose soil complete all as specified

M&L for Local sand cushioning with dry and clean sand over and under the under ground cable in trenches complete all as specified.

Supply and laying reinforced precast concrete cable cover, class LV, type 1 flat , of size 250mm x 150mm x 40mm complete all as specified

Supply and laying galvanised iron pipe 'light Grade' 50 mm dia in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified and directed .Make: Jindal/Prakash Surya/Tata

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 3.5 core x 35 Sqmm complete all as specified and directed

Chitragupta Construction

SATHI ENTERPRISES

ss construction

BHATIA ASSOCIATES

NIDHI CONSTRUCTION

M/S Sunshine Construction

M/S UnitedConstruction

sunway associates