COMPREHENSIVE MAINTENANCE AND CERTAIN B/R AND E/M REPAIR WORK OF JCO/ORS MD ACCN BLDG NO P-98 (06 QTRS) AND P-99 (06 QTRS) AT TARAPORE ENCLAVE AND OTHERS BLDGS IN THE AOR OF AGE B/R-I UNDER GE (A) SURATGARH AT SURATGARH MIL STN

M&L for 50mm thick PCC 1:3:6 type B-1, using 20mm graded stone aggregate as in plinth protection, laid in slope in 1:30 in pannels n. exc. 2m long including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level),complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M & L sand Stone slab 25 to 35 mm thick, dressed True and squre in one length not less than 60 CM and n exc 120 CM in coping, window cill , chajjs, sunshed etc, punched dressed on exposed faces and self faced on the embeded unexposed bed and joints exposed edges rounded and chamfered as directed set jointed in cement mortor.

M & L for brick work with fly ash, old size bricks, straight or curved on plan exc 6 m mean radius , built in CM in 1:6 including demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M & L 15 mm thick rendering on fair faces of brick walls or concrete surface in CM 1:4 , finished fair & smooth without using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specifeid and as directed

M & L 10 mm thick rendering on ceiling in CM 1:3 , finished fair & smooth w/o using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

Taking down / dismantling ceiling plaster,cutting surface in square or rectangular pattern & remove loose material all around the exposed reinforcement,binding/welding mild steel XPM wire to exposed reinforcement,applying the concrete rich mix 1:1.5:3, using 6mm stone aggregate and making the surface level and curing for 6-7 days and ceiling plaster in 1:3 etc complete all as specified and as directed by Engineer-in-charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc including two coat of sinthetic enamel paintcomplete all as specified and as directed

M&L for 20-25mm thick machine cut Kota stone slab flooring as in floor, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab incl. rubbing and polishing with mirror polish including & over 15 mm thick screed bed or bedding layer in CM 1:6 including demolition of existing stone slabsany type and tiles in flooring or on vertical surfaces complete all as specified.

M&L for 20-25mm thick machine cut Kota stone slab in single piece on treads of steps, , laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab incl. Rubbing and polishing with mirror polish complete & rendering 10 mm thick in CM(1:4) inclunding dismentling of stone/Kota stone slabs and tiles in flooring or on vertical surfaces all as specified and complete.

M&L for machine cut16-18mm thick Granite (of any type) , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including & over 15 mm thick screed bed or bedding layer in CM 1:6.inclunding demolition of stone slabs any type and tiles in flooring or on vertical surfaces complete all as specified.

M&L for Glazed ceramic tiles in vertical surface of 600x 300x 7 mm thick on vertical surface such as dado, skirting etc, set in tile adhesive conforming to IS-15477-2019 type-2 and thickness as per manufacturer instruction of approved make including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge all as specified and complete.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering or bedding layer in CM 1:4. including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for preparation old plastered ceiling/soffits of chajjas surfaces and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of Old plastered surfaces of walls and applying two coats of white wash complete as spd & directed

M&L for preparation of new plastered ceiling/soffits of chajjas surfaces and applying three coat of white wash complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall by vaccume based sanding machine, applying 2mm thick wall care putty(Multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats of interior emulsion paint over a coat of primer white or coloured by Roller or Air Spray complete all as specified and as directed. Note :- Paint and primer shall be same make. (MAKE :-Tractor Emulsion (Asian Paints), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent brand of Make specified in Appendix 'A

Material and labour for complete removal of existing treatment from old plastered surfaces of wall by Vaccume based sanding machine, removal of nails etc & filling cracks/hole with putty, applying wall care putty upto 2mm thick or as required ( Multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats of Interior emulsion paint white or coloured over a coat of primer by Roller or Air Spray complete all as specified and as directed. (MAKE :-Tractor Emulsion (Asian Paints), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent brand of Make specified in Appendix 'A

M&L for complete removal of exterior old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying two coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete over a layer of acrylic wall putty to achieve desired smoothness all as specified & directed by Engineer-in-Charge. (Brand :- Apex Ultima (Asian Paint), Weather Coat ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent brand of Make specified in Appendix 'A')

M&L for preparation of newly plastered surface of walls & Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a layer of 1.5mm thick acrylic wall putty to achieve desired smoothness. complete all as specified and directed by Engineer-in-charge. Note : Paint and primer shall be same make (Brand :- Apex Ultima (Asian Paint), Weather Coat ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent brand of Make specified in Appendix 'A'.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 sqm but n.exc 4 sqm (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats including S &F pressed steel door frame of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 sqm but n.exc 4 sqm (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats including S &F pressed steel door frame of size 105x60mm for doors with one or more rebates including nacessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats including S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 19-20 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 and natural gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,including 150mm extruded aluminium tower bolt ( 2 for each door) & 125mm extruded aluminium handle ( 2 No each door) all as per direction of Engineer-In-Charge.

S&F anodised aluminium window / ventilators shutters powder coated (thickness of powder coating shall not less than 50 micron) side hung type/Fixed type, without sash bars having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, anodised aluminium snap beading, screws, rubber neoprene packing including anodised aluminium fitting such as peg stay 150mm long (1 No), hinges type B21 100mm size (2 Nos), suitable handle (1No) including taking down steel window/ ventilator of any description and of any type with or without guard bars, including 5mm Glass and Galvanized Stainles steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, complete all as specified and directed by Engineer-in-Charge.

Taking down old UnSV windows/ ventilator of any description and S&F anodised aluminium frames powder coated (thickness of powder coating shall not less than 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc including taking down steel window/ ventilator of any description and of any type with or without guard bars complete all as specified and directed by Engineer-in-Charge.

S&F as in repairs stainless steel drapery rod of 20 mm inner dia (in lengths as directed) with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

Supplying and laying of 20mm OD bore / 1/2" CPVC pipes SDR 11 & Plain / brass CPVC SDR 11 fittings including all fittings and fixed complete to walls and ceilings or laid in floors, trenches including plug at opening or points for fitting and fixtures and powder coated clamps for fixing in walls including special fittings Brass Elbow(3/4x1/2), tee, Brass threaded Adapter(MTA/MBTA), Brass threaded Adapter(FTA/FBTA), tank Adapter ,Union, ball valve for connection of CPVC tubing inlcluding taking down existing old unseviceable tubing complete all as specified and directed by Engineer-in-charge.

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain / brass CPVC SDR 11 fittings including all fittings and fixed complete to walls and ceilings or laid in floors, trenches including plug at opening or points for fitting and fixtures and powder coated clamps for fixing in walls including special fittings Brass Elbow(3/4x1/2), tee, Brass threaded Adapter(MTA/MBTA), Brass threaded Adapter(FTA/FBTA), tank Adapter ,Union, ball valve for connection of CPVC tubing inlcluding taking down old existing unseviceable tubing complete all as specified and directed by Engineer-in-charge.

Supply & fixing in repair vitreous china premium/1st quality wash down water closet wall hung EWC white/ivory/off white (closed pattern incl all necessary accessories like rag bolts/gel gasket etc with & including WC seat cover closed pattern symphonic action type twin flush flushing cistern of 10 litre capacity with lid , incl CP jet spray and Health faucets of made of stainless steel connected for EWC necessary fitting and also incl Angle Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and 600 mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and as directed. Make :- Parryware Cat Part No "C022N & C0762" /Jaquar/kohlerTechno commercial equivalent in make equivalent to Appx 'A'.

S&F as in repair 15mm bore cast copper alloy, bib tap with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed.

S & F in repair brass chromium plated shower rose, 125 mm and arm with swivel joint including stop valve cast copper alloy concealed , screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 15 mm dia, ISI marked complete.

S & F as in repair 15 mm bore chromium plated Angular stop valve of cast copper alloy screwed down high pressure with on/off handle screwed both ends for iron pipe or for unions and fixed all as specified and directed

S&F as in repairs 20mm dia CPVC Ball valve or Gate Valve both ends for CPVC pipe and fixed complete all as specified and directed.

S&Fas in repair vitreous china Wash hand basin angle back 400x400mm ,including angle iron brackets and stainless steel coupling and waste pipe including 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD" with long screwed shank fly nuts, screwed suitable for iron pipes of 15mm bore and also including 32 mm bore brass chromium plated bottle trap for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing, union and cap and also 600 mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-Charge

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc and Supply & fixing 110mm bore PVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Note:- Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. Note: (i) the testing for leakage of pipe shall be done before connecting the pipes (ii) All pipes shall be minimum 4" away from walls fixed with GI bracket (iii) The gully trap shall be minimum 90 cm away from wall. (iv) Separate pipes for each floor should be provided. (v) Sewage and drain system shall be seperate.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc and S&F in repair PVC (SWR) pipes bore 75 mm single socketed, in any length with rubber ring joints,incl all the necessary fitting like bends/trap/tee etc in wall including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Note:- Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. Note: (i) the testing for leakage of pipe shall be done before connecting the pipes (ii) All pipes shall be minimum 4" away from walls fixed with GI bracket (iii) The gully trap shall be minimum 90 cm away from wall. (iv) Separate pipes for each floor should be provided (v) Sewage and drain system shall be seperate.

M&L for Roof Treatment in as specified below and as directed : (a) Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed. (b) Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed. (c) 40 mm avg thick PCC 1:2:4 type C 2 (12.5 mm graded aggregate) in roof complete all as specified and directed (d) Cleaning, washing of surface and removing any debris, Surface should be free from any loose paint, dust or grease. (e) Applying one coat of Elastomeric PU Based liquid membrane diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm. (f) Laying polyster reinforced fiber net/150 gsm Geotextile mesh, upto 300 mm on walls. (g) Applying two coats of undiluted PU Based liquid membrane, having Elongation more than 400%, Tensile Strength more than 2 N/mm2 and alkali & fungal resistant maintaining thickness of 1.5mm, with paint brush/ roller upto 300 mm on walls.(h) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment .

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 48 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 48 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per serial item No. 48 here-in-before but for One light point controlled by Two 2- way switches.

All as per serial item No. 48 here-in-before but for One bell or buzzer point controlled by by one push button on independent board.

All as per Srl item No. 48 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 15/16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 6 Amps single pole, two way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular bell push, flush type, 5 Amp, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F Modular socket outlet 2/3 pin 06/16A, 6 pin,2 module, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F electric bell (ding - dong), AC, 230 Volts, Single pole & connecting up complete all as specified and directed by Engineer-in-charge.

Supply and fixing LED luminaire surface/ceiling light, 12 watt, 220 V AC recessed type with opal diffuser complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make : Havells Cat Part No.:- LHEABMP7UL1W012/Crompton Cat Part LCDSPLN-R-12CDL/Wipro Cat Part D641265 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix "A".

Supply, fixing and testing in repair LED Street / Security light fitting of 30 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge. S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHETAVU7PA7J030/Crompton Cat Part TRP-415-30-57-SL-LM-NBK/Wipro Cat Part D912065 or equivalent cat part of Make as specified in Appendix "A".

Notes for srl Item No 61 :- (a) Tenderer shall submit test report of LED street light fitting from Government accredited test laboratory for LM - 79 and LM - 80 . (b) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. Contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. The product will be replaced free of cost in the following case :- (i) Manfacturing defects (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (c) All LED light/luminare must meet the provision laid down in IS - 16101 , 16102 Part -I/II ,16103 Part -I , 16104 ,16105 ,16106 , 16108/2012 and 15885 Part -II / Section 13. (d) Scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, If street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, In that case cost of additional / alteration is included in the unit rate of this item, which also includes needful T & P and required accessories such as 1.5 sqmm, 3 core PVC insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .No extra payment is admissible on this account. (e) Light fittings shall be provided with 10 KV surge protection as mentioned in description of item. If 10 KV surge protection is not provided in light fitting for which cat part is mentioned in BOQ. Contractor has to provide light fitting with 10 KV surge protection without any extra cost to department. (f) Contractor shall write CA No on street light fitting with synthetic enamel paint which should be visible from ground level. Cost of the same is included in the unit rate of this item nothing shall be extra paid on this account.

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F as in repair MCB 40-63 Amps, SPN, 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F as in repair MCB 40-100 Amps, TPN 415 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

S&F as in repair street light bracket made out of 32mm dia GI pipe light grade 1.20m long , bent to shape at 120 degree angle from vertical fixed along pole with and dirlling holes including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint including any addition / alteration (if required) for fixing street light complete all as specified and as directed by Engineer-in-charge.

Please Enable Macros to View BoQ information