ADDN/ALTN TO WINDOWS OF P-203, TOILETS AND BATHROOMS OF ZONE A AND B AND BLDG NO. 185 B, PROVN OF FANS, WATER COOLER AND SPLIT AC AT NCHC POWAI UNDER GE(NW) BHANDUP

Amount

Taking down chowkats or frames, exc 1.5 sqm and n. exec. 4 sqm each with shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also including taking down grills/guard bars (where exists), complete all as specified and directed

Taking down chowkats or frames, not exc 1.5 sqm each with shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also including taking down grills/guard bars (where exists), complete all as specified and directed

Taking down shutters of any description including fittings exc. 1.00 to 2.00 Sqm and removing from site.

Taking down cement or cement lime plaster on brick or stone wall etc., including racking out joints, hacking for key, scrubbing down with water etc.

M&L for 18 to 20 mm thick Udaipur Green Slab (table rubbed and Polished) including molding of edges in single piece as in window cills, jambs and the like over and including 15mm thick cement mortor screed bed in CM 1:4, also including pointing with white cemet (1:2) using marble dust with admixture of pigment to match with the shade of stone slab, complete all as specified and directed.

M&L for Rendering 15 mm thick (1:6) CM on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement.

M&L for rendering in CM in ceiling on fair faces of brick work or concrete surfaces,1:3, 10mm thick finished even and smooth with out using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in Cement Mortar 1:4 in two coats (10 + 5) with water proofing compound including finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid separately).

Supply only integral water proofing compound

S&F IInd class hard wood plain solid straight chowkats and framed rebated on the solid rounded put together with glue pinned at joints all as specified.

S&F plain framed factory made pannelled shutters (two panels with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and stile as per IS:1003(part-I) , kiln seasoned and chemically treated all as specified.

M & L for 2nd class hard wood (SAL) glazed and skelton shutters, 35mm thick, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, Chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc sizes of members of shutters as specified in SSR Part I Section 8 cluase 8.20(a) and fitted to chowkats complete all as specified and directed.

M&L for MS hold fasts size 25x6mm FI fixed to chowkats.

M&L for providing PCC 1:2:4 type B1 cement concrete in bed blocks for hold fasts.

Hacking out old broken glass panes (any thickness, size, quality and description) from steel frames fixed with oil putty area n.exc .5 Sqm all as directed

S&F alluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 300 mm

S&F aluminium section in sliding windows/ventilators ,any type (sliding on minimum two PVC roller of best qulaity for each shutter), powder coated in approved colour (Thickness of powder coating not less than 50 micron), aluminium section (medium weight of series 'B') as section directed by Engineer-in-Charge, cut to size, jointed together with cadmium plated steel screws including rubber beading or gasket for aluminium sections for fixing glass/XPM jali and all necessary fittings complete, screws, plugs for fixing screws, etc all as specified and directed Notes : (i) Weight of aluminium sections shall only be measured. (ii) Rate quoted by the contractor shall deemed to be inclusive of all necessary fittings and fixture such as roller, handle locks etc. Quoted rate shall be deemed including cost of rubber beading or gasket etc and will be not measured separately. (iii) Glass pane and wire mesh will be measured and paid separately under relevant items as supply only.

S&F in repairs 4 mm thick sheet glass, ordinary quality and glazing with aluminium beading/packing with rubber gasket in squares n.exc 0.50 sqm complete as specified and directed.

Supply only 4mm thick Sheet glass, ordinary quality in squares exc 0.5 sq. m in each pane complete all as specified and directed.

Supply only figured glass,tinted colour, pin head type,4mm thick, in square n.exc.0.5sqm in each pane for fixing aluminium frame complete all as specified and as directed.

Supply only aluminium wire cloth 0.45mm nominal dia of wire and arrange width of aperture 1.40mm for fixing in aluminium windows along with complete all as specified and directed by the Engr-in-Charge

S&F aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel all as specified and directed. Note: The Grills shall be of Model DG-102 or any other Model of Make Deco or equivalent make as approved by the GE.

S&F and mild steel framed work as in grills, greating and guard bar with end of bars shouldered and / or reveted or forged into spikes nad similar works confirming to Fe-410 and Fe-310.

M & L for preparation of new surfaces on wall and applying two coats of 100 % acrylic emulsion paint over a coat of acrylic primer incl. complete removal of existing treatment and necessary scaffolding complete all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying two coats of 100% anti fungal weather resistant acrylic paint over a coat of acrylic primer in approved shade and as per manufacturer's instructions including necessary scaffolding complete all as specified and as directed.

M&L for preparation new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer compelte all as specified and directed by EIC

M&L applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any desccription exc. 10Cm width or girth incl. preparation of surfaces.

M&L for preparation of new plastered surface of celling and applying 3 coats of white wash.

M & L for preparation of old plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including washing down with water etc. applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

S & F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown in drg for SI No. 8095 on ser page No. 160 in SSR-2010 (Pt-II), complete all as specified and directed.

S&F Factory Made Solid Panel PVC Door Shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet shall be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, as per specification & drawing for SI No.8080 on srl page No.156 in SSR-2010 (Pt-II), complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, 100mm long, complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, 75mm long, complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section, 100 mm long, complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section, 200 mm long, complete all as specified and directed.

S&F aluminium anodised bow handles of 100mm size, fabricated type of extruded section fixed with screws to shutters, complete all as specified and directed.

S&F aluminium anodised bow handles of 125mm size, fabricated type of extruded section fixed with screws to shutters, complete all as specified and directed.

S&F alluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 300 mm

M&L for applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth complete all as specified and directed.

S & F machine cut cudappa stone slab 20-25 mm thick over cement screed bed 15 mm thick in CM 1:4 laid and jointed with pigment to match the shade of slab including rubbing and polishing in doors /windows cills and jambs in step complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thick (above or below ground level) and removing the retrieved debris outside MD land, complete all as specified and directed.

Dismantling floor, hearth or wall tiling and stone slabs including cement mortar bedding (but not backing), removing rubbish off the premises outside MD Land complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for coloured 450x350x7mm/350x250x7mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete all as specified and directed.

M&L PCC 1:4:8 type-D2 with using 40mm graded aggregate, 75mm thick sub base.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement mortar screed

S&F in repairs vitreous china squatting pan orissa, pattern size 580x440mm white with integral footrest. incl trap set & concrete including flushing cistern 10 liters capacity of white PVC connection 15mm size with PTMT nuts of length 450mm long including stop valves cast copper alloy 15mm bore screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or unions etc complete.

S&F low density polyethylene pipes 32mm bore fixed complete to walls ceiling or in floorcomplete all as specified.

S&F Grating doom 100mm dia of PTMT (Minimum Weight 25 gms) complete all as specified.

S&F in repair bib taps 15mm, cast copper alloy with crutch or butterfly handle screwed for iron pipe or for brass ferrule and fixed.

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MD land, complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement, complete all as specified and directed.

S&F PVC connections 15mm size with brass nuts & PVC washers of length 450mm.

S&F WC Pedestal pattern vitreous china coloured with match colored plastic seat cover, including 10 Ltr capacity PVC flush tank low level coloured match with WC.

M&L for Brick work with Sub class 'B' old size Bricks and of class designation 35(minimum compresive strenght 35 Kg/cm2), straight or curved on plan to any radius, as in half brick thick wall built complete all as specified and directed.

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

S&F for stop valves, cost copper alloy 15mm bore, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union & fixed.

S&F brass chromium plated shower rose 125mm size.

S&F in repairs, White, Vitreous china, 1st quality, bowl urinal,(flat back or corner wall type) of size 465x355x265mm (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and directed.

S&F in repairs Vitreous china coloured wash hand basin of oval size 575x475mm with waste cupling including fancy type pillar tap 15mm dia . including mild steel angle brackets,CP brass fittings, waste, union, cutting for and pinning ends of brackets, provision of 32 mm dia PVC waste pipe complete all as specified and directed .

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, wash hand basin platform and other similar situations

Taking down GI tubing 15mm bore including connections

Taking down GI tubing 20mm bore including connections

S&F tubes medium grade, galvanized 15mm bore with all fitting & fixed complete to walls & ceiling or laid in floor.

S&F tubes medium grade, galvanized 20mm bore with all fitting & fixed complete to walls & ceiling or laid in floor.

S&F stainless steel Urinal Push cock complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated unsheathed 1100 volts grade FRLS cable stranded copper conductor single core in rigid PVC conduit/casing caping of 20/25 mm complete with sunken iron pressed steel terminal box with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth dolly for the following points all as specified and directed. (a) One fan point controlled by one Socket Complete

S&F for switch,Piano flush type 5A single pole,one way, 230 V ISI marked

S&F for Socket Outlet 2 in 1 3/5 Pin 5Amp flush type, 230V,50 Hz complete

Supply and Fix wall mounted fan 250 mm sweep Jerk free oscillation and smooth running, incl. thermal overload protector (TOP) for protecting the motor in case of any high voltage fluctuation, Aerodynamically designed balanced heavy duty PP blades complete all as specified and directed.

Supply, installation and commissioning of water cooler fully stainless steel with RO water purifier, two faucets, electric driven at 230V, 50Hz, 1 Phase AC having 80 litres storage capacity and 40 litres/hr cooling capacity complete all as specified and directed.

S&F gun metal gate valve with iron wheel head of size 20 mm with external threaded both ends for connecting to pipe line incl. complete all as specified and directed.

M&L in trenches/wall and jointing 20 mm bore GI tubing incl. all fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc complete all as specified and directed.

Supply and installation of wall split type air conditioner indoor/outdoor units having dust filter, 5 Star BEE rating with copper tubing of capacity 1.5 ton complete with cordless remote control unit incl. testing all as specified and directed.

S&F Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of + 2.5% and of capacity 4.0 kVA.

Deduct Credit for Demolished/ Dismantled material Rs. (-) 1,16,550.00 (Minus) as listed in Schedule of Credit Note: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

M/s. Deepak Traders

M/S VISHRANTA CONSTRUCTION

R K TYAGIS

SB CONSTRUCTION